Optimal design of sintered Ce_9Nd_(21)Fe_(bal)B_1 magnets with a low-melting-point (Ce,Nd)-rich phase

A systemic investigation was done on the chemistry and crystal structure of boundary phases in sintered Ce9Nd21FebalB1 （wt%） magnets. Ce2Fe14B is believed to be more soluble in the rare-earth （RE）-rich liquid phase during the sintering process. Thus, the grain size and oxygen content were controlled via low-temperature sintering, resulting in high coercivity and maximum energy products. In addition, Ce formed massive agglomerations at the triple-point junctions, as confirmed by elemental mapping results. Transmission electron micros- copy （TEM） images indicated the presence of （Ce,Nd）Ox phases at grain boundaries. By controlling the composition and optimizing the preparation process, we successfully obtained Ce9Nd21FebalBx sintered magnets; the prepared magnets exhibited a residual induction, coerciv- ity, and energy product of 1.353 T, 759 kA/m, and 342 kJ/m3, respectively.

Influence of high magnetic field on as-cast structure of Cu-25wt.%Ag alloys

To investigate the influence of high magnetic field (HMF) on the solidification microstructure of Cu-25wt.%Ag alloy, the Cu-25wt.%Ag alloy was prepared under HMF of 12 T, and for comparison, the alloy solidified without HMF was also fabricated. Macro and microstructures of the alloys were observed using the stereomicroscope, and scanning electron microscope, field emission scanning electron microscopy. The weight percentages of the pro-eutectic and eutectic, Cu phase and Ag phase in eutectic, and precipitates of Ag phase in pro-eutectic were analyzed by using of IPP software. Results show that the morphology of the column dendrites changes into cellular dendrites and the grains are refined under HMF of 12 T. Meanwhile, the thickness of the eutectic wall increases, but the sizes of Cu phase and Ag phase and the eutectic lamellar spacings are decreased. The Ag precipitates in the Cu matrix become coarser and sparser. The weight percentage variation of the phases in the microstructure and the Cu-Ag binary phase diagram reveals that the eutectic point moves to the left of the eutectic point in the equilibrium condition and the supersaturated solid solubility of Ag decreases under HMF.

Thermodynamic prediction of the composition of Fe-based amorphous alloys

The liquidus univariant lines of the Fe-Nb-B ternary system have been thermodynamically calculated by means of CALPHAD method and Fe-based thermodynamic data. It is found that there are two eutectic reactions in the Fe-rich corner,that is,（1） L（Fe-3Nb-15B） →α＋γ＋ M2B （1430 K）,and （2） L（Fe-10Nb-27B） → FeB ＋ Lc14 ＋ M2B （1575 K）. Moreover,the eutectic points are very close to the compositions with high glass forming ability determined experimentally. This means that it is feasible to design the compositions of multicomponent bulk metallic glasses by looking for the eutectic points in the Fe-Nb-B system by means of thermodynamic calculation.

Preparing and Studying of Phase Change Energy Storage Materials

The thermal energy storage phase change material used for building has been prepared with a few of fatty acids based on the principle of binary low eutectic point. The thermal behaviors such as phase transition temperature and enthalpy of compound energy storage material are researched through differential scanning calorimeter(DSC) and scanning electron microscope(SEM) . The results show that the thermal energy storage phase change composite material can be used in the wall panels well as its higher latent heat.

Microstructure Evolution During Remelting of High Solid Fraction ZL101 Alloy

This work deals with the reheating process for semi-solid thixoforming of ZL101(Al Si7 Mg) alloy. The semi-solid state can decrease the viscosity and the resistance while sheared because of the evolutional behavior,which is characterized by a solid-like behavior at rest and a liquid flow during shearing. The microstructure evolution of ZL101 alloy at different temperatures from 540 to 580?C has been studied. Results show that the eutectic temperature can affect the transformation speed of semi-solid structure. Semi-solid microstructures with high solid fraction can be obtained by controlling the reheating time in less than 20 min, while at the temperature lower than the eutectic temperature it needs more than one hour. Another character of semi-solid ZL101 alloy is the segregation of microstructures in semi-solid state, in which the liquid phase between the solid phases can flow freely and lead to the shrinkage of the sample during the heating process. As the holding time goes on, more shrinkage holes appear and change the surface of the specimen. These shrinkage holes are replenished by the liquid phase during compression deformation, resulting in the segregation of the components.