Effects of individual and combined additions of phosphorus,boron and cerium on primary and eutectic silicon in an Al-30Si alloy

The modification of silicon in an Al-30Si alloy was studied using optical microscopy, electron probe micro-analysis, transmission electron microscopy and differential scanning calorimetry. It is found that phosphorus master alloys combined with boron master alloys have good modification effect on primary silicon but no evident modification effect on eutectic silicon, while boron combined with cerium has good modification effect on eutectic silicon. The results of differential scanning calorimetry show that phosphorus, boron or cerium addition and their combined addition have different undercooling effects on eutectic silicon. Many scholars thought that AlP particles were the nuclei of eutectic silicon when phosphorus was enough in the alloy. Our results show that β-（Al,Si,Fe） can still be the nucleus of plate-like entectic silicon while AlP is the nucleus of primary silicon when there is enough phosphorus in the melt. In addition, the mechanism about the modification was also discussed.

Modified Mechanism of Eutectic silicon in Al_2O_3/Al-Si Alloy

Al2O3/Al-Si alloy composite was manufactured by squeeze casting. The morphology of the eutectic silicon in the composite was observed by scanning electronic microscope (SEM), and the modified mechanism of eutectic silicon in the composite was approached. The alumina fiber in the composite can trigger twin during the growth of Al-Si eutectic and lead to the modification of eutectic silicon near the fiber.

An Al-12Si/ZnS powder inoculant for eutectic silicon in Al-12Si alloy

To obtain high-performance Al-Si-based cast alloys,refinement and modification of Si phases are required.An Al-12Si/ZnS powder inoculant was designed and fabricated using a chemical bath deposition method.The efficiency of the inoculant for modifying the eutectic Si phase in as-cast Al-12Si alloy was studied.Results show that Al-12Si/ZnS powder can significantly refine the eutectic Si in Al-Si cast alloys.The best refinement effect for eutectic Si is achieved with 17.5wt.%Al-12Si/ZnS powder.Coarse long needle-shaped eutectic Si with a length of 18μm was modified into approximately spherical shape with a diameter of 6.53μm,which is evenly distributed throughout the alloy.The E2EM model calculation indicates that the inter-plane misfit(F_(p))and inter-atomic spacing misfit(F_(r))between ZnS and Si are all less than 0.5%,which confirms that ZnS is a potential nucleation site for Si phase.The hardness,tensile strength,and elongation of Al-12Si alloys modified with 17.5%Al-12Si/ZnS powder increase 6.30%,16.18%and 55.45%,respectively,compared to the unmodified Al-12Si alloy.The fracture behavior of the alloy with 17.5wt.%Al-12Si/ZnS powder is dominated by transgranular fracture supplemented by intergranular fracture.

Preparation and Characterization of CA-MA Eutectic/Silicon Dioxide Nanoscale Composite Phase Change Material from Water Glass via Sol-Gel Method

This work mainly involved the preparation of a nano-scale form-stable phase change material（PCM） consisting of capric and myristic acid（CA-MA） binary eutectic acting as thermal absorbing material and nano silicon dioxide（nano-SiO_2） serving as the supporting material. Industrial water glass for preparation of the nano silicon dioxide matrix and CA-MA eutectic mixture were compounded by single-step sol-gel method with the silane coupling agent. The morphology, chemical characterization and form stability property of the composite PCM were investigated by transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, Fourier-transform infrared（FT-IR） spectroscopy and polarizing microscopy（POM）. It was indicated that the average diameter of the composite PCM particle ranged from 30-100 nm. The CA-MA eutectic was immobilized in the network pores constructed by the Si-O bonds so that the composite PCM was allowed no liquid leakage above the melting temperature of the CA-MA eutectic. Differential scanning calorimetry（DSC） and thermogravimetric analysis（TGA） measurement were conducted to investigate the thermal properties and stability of the composite PCM. From the measurement results, the mass fraction of the CA-MA eutectic in the composite PCM was about 40%. The phase change temperature and latent heat of the composite were determined to be 21.15 ℃ and 55.67 J/g, respectively. Meanwhile, thermal conductivity of the composite was measured to be 0.208 W·m^（-1）·K^（-1） by using the transient hot-wire method. The composite PCM was able to maintain the surrounding temperature close to its phase change temperature and behaved well in thermalregulated performance which was verified by the heat storage-release experiment. This kind of form-stable PCM was supposed to complete thermal insulation even temperature regulation by the dual effect of relatively low thermal conductivity and phase change thermal storage-release properties. So it can be formulated that the nanoscale CA-MA/SiO_2 composite PCM with the form-stable property, good thermal storage capacity and relatively low thermal conductivity can be applied for energy conservation as a kind of thermal functional material.

Eutectic nucleation in Al-25wt.% Si alloy through DSC

Eutectic nucleation in hypereutectic Al-25wt.%Si alloy with the addition of P was studied by calculating the activation energy and nucleation work. The results indicate that P refinement, which can decrease the activation energy as well as nucleation work of eutectic solidification, can increase the eutectic nucleation frequency of Al-25wt.%Si alloy, so the addition of P can refme the eutectic structures of hypereutectic Al-Si alloys. According to the calculations, there is a certain relationship between the precipitation of primary silicon and eutectic solidification, and the eutectic nucleation mode is independent of morphology transition.

Microstructural Feature of As-cast A-356 Alloy Modifiers with the Addition of SrO

To explore the effect of strontium on the structure of as-cast A356 alloy, the strontium was incorporated to the alloy by metallothermic reduction of SrO where the mineral was added to the melt through the submerged powders injection technique. The evaluation of the modification of the eutectie silicon and the chemical analysis of samples were done using optical microscopy （OP） and inductively coupled plasma （ICP）, respectively, while microstructural analyses by scanning electron microscopy （SEM）, and the injection time was variable. Magnesium was added to the melt to increase the reactivity and reduce the surface tension of the molten aluminum. It was possible to increase the strontium content from 0 to 0.027% after 20 minutes treatment. This concentration was sufficient to bring about full modification structure of eutectic silicon of as cast alloy A 356 and the acceptable quality metallurgical of alloy.

Al–9.00 %Si–0.25 %Mg alloys modified by ytterbium

The effects of ytterbium（Yb） on microstructure and solidification behavior of Al-9.00%Si-0.25%Mg alloys were investigated.By optical microscope（OM） and scanning electron microscopy（SEM）,it is found that the morphology of eutectic silicon changes from coarse plates to fine fibers by the addition of 0.7%wt Yb.In addition,the grains of α-Al matrix are refined by Yb addition.Phase constitution of the alloy was analyzed by X-ray diffractometer（XRD） and energy dispersive spectroscopy（EDS）attached with SEM and mechanical properties were measured by hardness test.It is concluded that the Yb atoms are incorporated into the silicon by the adsorption at the solid-liquid growth front to cause the modification of eutectic silicon.Furthermore,the results of XRD and EDS analysis reveal that the Yb-containing phase forming in the alloys is Al_3Yb.

In-situ Observation of Tensile Fracture in A357 Casting Alloys

The mechanism of damage evolution and fracture in A357 casting alloys was investigated by in-situ scanning electron microscopy （SEM） tensile testing. Different microstructures of A357 casting alloys were produced by eutectic Si modification and T6 heat treatment. It is shown that microcracks in these alloys are predominantly formed in eutectic Si particles. Large and elongated eutectic Si particles in unmodified alloy show the greater tendency to cracking, whereas cracking of small and round eutectic Si particles in Sr modified and T6 heat treated alloys is relatively lag. The crack mainly propagates along the broken eutectic Si particles in unmodified and Sr modified alloys or along the deepened shear bands in T6 heat treated alloy with accumulating the applied strain. The results were discussed in terms of Weibull statistics and the fracture models were established.