The effect of sintering dispersed and bulk,low molecular weight(M_n=50,000 Da),nano-emulsionpolytetrafluoroethylene(PTFE)particles near their melting point is described.With the nascent particles consisting of ca.75 n...The effect of sintering dispersed and bulk,low molecular weight(M_n=50,000 Da),nano-emulsionpolytetrafluoroethylene(PTFE)particles near their melting point is described.With the nascent particles consisting of ca.75 nm diameter,hexagonal,single crystals,sintering at,e.g.,350℃,results,initially,in merger of neighboring particles,followed by individual molecular motion on the substrate and the formation of folded chain,lamellar single crystals andspherulites,and on-edge ribbons.It is suggested these structures develop,with time,in the mesomorphic“melt”.Sintering ofthe bulk resin yields extended chain,band structures,as well as folded chain lamellae;end-surface to end-surface merger,possibly by end-to-end polymerization,occurs with increasing time.展开更多
Thin wall samples of high density polyethylene （HDPE） were prepared via injection molding with different injection speeds ranging from 100 mm/s to 1200 mm/s. A significant decrease in the tensile strength and Young...Thin wall samples of high density polyethylene （HDPE） were prepared via injection molding with different injection speeds ranging from 100 mm/s to 1200 mm/s. A significant decrease in the tensile strength and Young＇s modulus was observed with increasing injection speed. In order to investigate the mechanism behind this decrease, the orientation, molecular weight, molecular weight distribution, melt flow rate, crystallinity and crystal morphology of HDPE were characterized using two-dimensional wide-angle X-ray diffraction （2D-WAXD）, gel permeation chromatography （GPC）, capillary rheometry and differential scanning calorimetry （DSC）, respectively. It is demonstrated that the orientation, molecular weight, molecular weight distribution, melt flow rate and crystallinity have no obvious change with increasing injection speed. Nevertheless, the content of extended chain crystals or large folded chain crystals was found to decrease with increasing injection speed. Therefore, it is concluded that the decrease in tensile properties is mainly contributed by the reduced content of extended chain crystals or large folded chain crystals. This study provides industry with valuable information for the application of high speed injection molding.展开更多
文摘The effect of sintering dispersed and bulk,low molecular weight(M_n=50,000 Da),nano-emulsionpolytetrafluoroethylene(PTFE)particles near their melting point is described.With the nascent particles consisting of ca.75 nm diameter,hexagonal,single crystals,sintering at,e.g.,350℃,results,initially,in merger of neighboring particles,followed by individual molecular motion on the substrate and the formation of folded chain,lamellar single crystals andspherulites,and on-edge ribbons.It is suggested these structures develop,with time,in the mesomorphic“melt”.Sintering ofthe bulk resin yields extended chain,band structures,as well as folded chain lamellae;end-surface to end-surface merger,possibly by end-to-end polymerization,occurs with increasing time.
基金supported by the National Natural Science Foundation of China(No.51073111)
文摘Thin wall samples of high density polyethylene （HDPE） were prepared via injection molding with different injection speeds ranging from 100 mm/s to 1200 mm/s. A significant decrease in the tensile strength and Young＇s modulus was observed with increasing injection speed. In order to investigate the mechanism behind this decrease, the orientation, molecular weight, molecular weight distribution, melt flow rate, crystallinity and crystal morphology of HDPE were characterized using two-dimensional wide-angle X-ray diffraction （2D-WAXD）, gel permeation chromatography （GPC）, capillary rheometry and differential scanning calorimetry （DSC）, respectively. It is demonstrated that the orientation, molecular weight, molecular weight distribution, melt flow rate and crystallinity have no obvious change with increasing injection speed. Nevertheless, the content of extended chain crystals or large folded chain crystals was found to decrease with increasing injection speed. Therefore, it is concluded that the decrease in tensile properties is mainly contributed by the reduced content of extended chain crystals or large folded chain crystals. This study provides industry with valuable information for the application of high speed injection molding.
