A mechanically coupled MEMS filter with high-Q width extensional mode resonators

This work presents a novel radio frequency(RF)narrowband Si micro-electro-mechanical systems(MEMS)filter based on capacitively transduced slotted width extensional mode(WEM)resonators.The flexibility of the plate leads to multiple modes near the target frequency.The high Q-factor resonators of around 100000 enable narrow bandwidth filters with small size and simplified design.The 1-wavelength and 2-wavelength WEMs were first developed as a pair of coupled modes to form a passband.To reduce bandwidth,two plates are coupled with aλ-length coupling beam.The 79.69 MHz coupled plate filter(CPF)achieved a narrow bandwidth of 8.8 kHz,corresponding to a tiny 0.011%.The CPF exhibits an impressive 34.84 dB stopband rejection and 7.82 dB insertion loss with near-zero passband ripple.In summary,the RF MEMS filter presented in this work shows promising potential for application in RF transceiver front-ends.

The internal circulations on internal mass transfer rate of a single drop in nonlinear uniaxial extensional flow

The internal flow of a droplet in the nonlinear extensional flow field will exhibit more than two internal circulations with the variation of nonlinear intensity(E).In this paper,the effect of positions and sizes of internal circulations on internal mass transfer rate of a single spherical droplet in a nonlinear extensional flow field is studied and compared with that in a linear extensional flow field.The simulation results show that when E≥0,there are two symmetrical internal circulations in the droplet,which is the same with that in a linear extensional flow.The limit value of mass transfer rate Sh is 15,which is equal to that in a linear extensional flow,no matter how large E is.When E≤-3/7,the number of internal flow circulation of a droplet increase to four and the transfer rate Sh increases.When E=-1,the maximum internal transfer rate Sh equals 30 which is twice of that in a linear extensional flow.The generation of new flow circulations in droplets and the circulation positions will enhance mass transfer when E≤-3/7,which provides a new idea for enhancing the internal mass transfer rate of droplets.

Origin of nucleation and growth of extension twins in grains unsuitably oriented for twinning during deformation of Mg-1%Al

A large number of anomalous extension twins,with low or even negative twinning Schmid factors,were found to nucleate and grow in a strongly textured Mg-1Al alloy during tensile deformation along the extruded direction.The deformation mechanisms responsible for this behaviour were investigated through in-situ electron back-scattered diffraction,grain reference orientation deviation,and slip trace-modified lattice rotation.It was found that anomalous extension twins nucleated mainly at the onset of plastic deformation at or near grain boundary triple junctions.They were associated with the severe strain incompatibility between neighbour grains as a result from the differentbasal slip-induced lattice rotations.Moreover,the anomalous twins were able to grow with the applied strain due to the continuous activation ofbasal slip in different neighbour grains,which enhanced the strain incompatibility.These results reveal the complexity of the deformation mechanisms in Mg alloys at the local level when deformed along hard orientations.

Diagnostic Study of an Extreme Explosive Cyclone over the Kuroshio/Kuroshio Extension Region

Explosive cyclones(ECs)occur frequently over the Kuroshio/Kuroshio Extension region.The most rapidly intensified EC over the Kuroshio/Kuroshio Extension region during the 42 years(1979-2020)of cold seasons(October-April)was studied to reveal the variations of the key factors at different explosive-developing stages.This EC had weak low-level baroclinicity,mid-level cyclonic-vorticity advection,and strong low-level water vapor convergence at the initial explosive-developing stage.The low-level baroclinicity and mid-level cyclonic-vorticity advection increased substantially during the maximum-deepening-rate stage.The diagnostic analyses using the Zwack-Okossi equation showed that diabatic heating was the main contributor to the initial rapid intensification of this EC.The cyclonic-vorticity advection and warm-air advection enhanced rapidly in the middle and upper troposphere and contributed to the maximum rapid intensification,whereas the diabatic heating weakened slightly in the mid-low troposphere.The relative contribution of the diabatic heating decreased from the initial explosive-developing stage to the maximum-deepening-rate stage due to the enhancement of other factors(the cyclonic-vorticity advection and warm-air advection).Furthermore,the physical factors contributing to this EC varied with the explosive-developing stage.The non-key factors at the initial explosive-developing stage need attention to forecast the rapid intensification.

Wellbore Cleaning Degree and Hydraulic Extension in Shale Oil Horizontal Wells

The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.

Application of Improved Matter-element Extension Method in Comprehensive Assessment of Shallow Groundwater

Taking shallow groundwater in Jinjiang City,Fujian Province for example,it was found that the classical element-matter analysis shows deficiency in calculation of correlation function,so the improved matter-element method was applied for the comprehensive assessment of shallow groundwater in Jinjiang City,and the spatial distribution was shown in maps.The assessment results demonstrated that ground water quality of most regions in the study area belonged to Grade I and II,thus the overall quality of shallow groundwater was good.The groundwater of Grade IV and V(relatively poor and extremely poor) was mainly distributed in Dongshi Town,Chendi Town,Zimao Town,and Shenhu Town,major exceeding-standard factors that influence shallow groundwater quality in the local area included TDS,Mn^(2+),NO_3,NO_2,NH_4^+ and Cl^-,which mainly owed to invasion of seawater,original geological conditions,industrial and agricultural discharge,and human life.

Estimation of Displacement and Extension due to Reverse Drag of Normal Faults: Forward Method

In the case of reverse drag of normal faulting, the displacement and horizontal extension are determined based on the established equations for the three mechanisms: rigid body, vertical shear and inclined shear. There are three sub-cases of basal detachment for the rigid body model: horizontal detachment, antithetic detachment and synthetic detachment. For the rigid body model, the established equations indicate that the total displacement on the synthetic base (Dt2) is the largest, that on the horizontal base (Dt1) is moderate, and that on the antithetic base (Dt3) is the smallest. On the other hand, the value of (Dt1) is larger than the displacement for the vertical shear (Dt4). The value of (Dt1) is larger than or less than the displacement for the inclined shear (Dt5) depending on the original fault dip δ0, bedding angle θ, and the angle of shear direction β. For all original parameters, the value of Dt5 is less than the value of Dt4. Also, by comparing three rotation mechanisms, we find that the inclined shear produces largest extension, the rigid body model with horizontal detachment produces the smallest extension, and the vertical shear model produces moderate extension.

Comparative Study of the Socioeconomic Characteristics and Digital Literacy Level of Agricultural Extension Personnel in Imo and Ebonyi States, South-East, Nigeria

The study comparatively analysed the socioeconomic characteristics and digital literacy level of Agricultural Extension personnel (AEP) in Ebonyi and Imo States, South-East, Nigeria. The specific objectives were to describe the socioeconomic characteristics of agricultural extension personnel in Ebonyi and Imo States, and to ascertain the digital literacy level of AEP in the studied states. Purposive sampling technique was used to select 312 Agricultural Extension personnel (132 from Ebonyi State Agricultural Development Program and 180 from Imo State Agricultural Development Program) for the study. Data were collected through the use of validated and structured questionnaire, and administered through the help of well-trained enumerators. Data were analysed using simple descriptive statistical tools such as percentages mean score, standard deviation and weighted mean. Findings indicated that they were more male in the both States (55.3% and 57.8%) for Ebonyi and Imo State respectively and that the average age of AEP in Ebonyi and Imo States were 44.7 years and 49.2 years respectively. It was further revealed that the majority (77.3% and 82.8%) had B.Sc./HND as their highest academic qualifications, belonged to professional organisations (62.1% and 75%), and were earning an average monthly income of N58,798 and N62,648 for Ebonyi and Imo State respectively. Also, it was revealed that their mean years of service were 12.4 years and 13.4 years for Ebonyi and Imo State respectively. Almost all of them (87.9% and 95.0%) own a smartphone, had access to the internet (80.3% and 90.0%), but do not own a laptop/ipad (82.6% and 72.8%) for Ebon-yi and Imo State respectively. Results further revealed that Agricultural extension personnel in both Ebonyi and Imo State respectively had low digital literacy level ( = 2.41 and 2.32). The study concluded that AEP in Ebonyi and Imo State respectively had similar socioeconomic characteristics and low level of digital literacy. The study recommended that the management of ADPs in both Ebonyi and Imo State should ensure the training of AEP in digital skills to enhance their digital literacy level to enable them use digital technologies in their work.

基于Fuzzy Matter-Element模型的电力上市公司财务核心竞争能力评价

鉴于电力上市公司财务核心竞争能力评价的复杂性以及单项指标评价结果的不相容性,本文在模糊物元分析的基础上,将熵权的理论方法与海明贴近度的概念相结合,建立了电力上市公司财务核心竞争能力评价的模糊物元模型。把不同电力企业作为物元的事物,以它们的各项评价指标及相应的模糊量值构造模糊物元,通过计算与理想模糊物元之间的海明贴近度,实现对上市电力公司财务核心竞争能力的综合评价。

Sandbox Modeling of the Fault-increment Pattern in Extensional Basins

Three series of sandbox modeling experiments were performed to study the fault-increment pattern in extensional basins. Experimental results showed that the tectonic action mode of boundaries and the shape of major boundary faults control the formation and evolution of faults in extensional basins. In the process of extensional deformation, the increase in the number and length of faults was episodic, and every ＇episode＇ experienced three periods, strain-accumulation period, quick fault-increment period and strain-adjustment period. The more complex the shape of the boundary fault, the higher the strain increment each ＇episode＇ experienced. Different extensional modes resulted in different fault-increment patterns. The horizontal detachment extensional mode has the ＇linear＇ style of fault-increment pattern, while the extensional mode controlled by a listric fault has the ＇stepwise＇ style of fault-increment pattern, and the extensional mode controlled by a ramp-flat boundary fault has the ＇stepwise-linear＇ style of fault-increment pattern. These fault-increment patterns given above could provide a theoretical method of fault interpretation and fracture prediction in extensional basins.

Dynamic Features of Angular Unconformity Formation——Extensional and Compressional Angular Unconformities

Angular unconformity is one of the most direct and strongest evidences for approving the tectonic movements of the earth's crust. Its dynamic genesis process has been understood to be mainly related to the compressional setting for a long time. Especially, in a detailed structural analysis for a specific region, when an angular unconformity is discovered people would regard it as the result of orogenic movements of a certain period or a certain episode and neglect the extensional facts. Based on a dialectical point of view of extension-compression, this paper has proved that angular unconformities can be formed not only in compressional settings, but also in extensional ones. Further more, their geological features are compared and he possible genetic mechanisms for angular unconformity under different dynamic settings are studied.

Extensional tectonics and sedimentary response of the Early—Middle Cambrian passive continental margin,Tarim Basin,Northwest China

The fact that several half-grabens and normal faults developed in the Lower--Middle Cambrian of Tazhong （central Tarim Basin） and Bachu areas in Tarim Basin, northwest China, indicates that Tarim Basin was under extensional tectonic setting at this time. The half-grabens occur within a linear zone and the normal faults are arranged in en echelon patterns with gradually increasing displacement eastward. Extensional tectonics resulted in the formation of a passive continental margin in the southwest and a cratonic margin depression in the east, and most importantly, influenced the development of a three- pronged rift in the northeast margin of the Tarim Basin. The fault system controlled the development of platform -- slope -- bathyal facies sedimentation of mainly limestone-dolomite-gypsum rock-saline rock-red beds in the half-grabens. The NW-SE trending half-grabens reflect the distribution of buried basement faults.

Spatio-temporal characteristics of acoustic emission during the deformation of rock samples with compressional and extensional en-echelon faults

The spatio-temporal characteristics of acoustic emission (AE) during the deformation of rock samples with compressional and extensional en-echelon faults have been studied. The results show that the pre-existing structure can significantly influence the patterns of AE spatial distribution. With increasing of differential stress, AE events firstly cluster around the two ends of pre-existing faults inside the jog and then along the line joining the two ends. The biggish AE events often occur around one end repeatedly. The image of AE clusters indicates the direction and the area of the fracture propagation. The direction of the macroscopic fracture in extensional and compressional jogs is perpendicular and parallel to the direction of axial stress, respectively. The weakening process before the fracturing of jog area is remarkable, and one of the typical precursors for the instability is that the cumulative frequency of AE events increases exponentially. After the fracturing of the jog the frequency and releasing strain energy of AE events decrease gradually. During the friction period, there is no precursory increasing of AE activity before the big stick-slip events. The change of b value in jog shows a typical change of decreasing tendentiously returning quickly before the instability. The decrease of b value occurs in the process of stress increasing and sometime goes down to the weakening stage, and the quick increase b values appears in a short time just before the instability. The comparative analysis shows that the difference in b value due to the different structures is larger than b value variation caused by increase of the differential stress. For the same sample, the temporal sequence of AE is strongly affected by the mechanical state, and the high loading velocity corresponds to the high release rate of strain energy and low b value. Due to its lower failure strength, the broken area is sensitive to small changes in differential stress. Therefore, it offers a potential explanation for the phenomena of precursory window or sensitive point and separation of seismic source and precursors.

Coulomb stress evolution along the Kongur Extensional System since 1895 and present seismic hazard

The present-day tectonic activities on the northeastern margin of the Pamir Plateau are mainly E-W oriented extensions, among which the Kongur Extensional System(KES) plays an important role in the internal expansion of the Pamir. As the largest earthquake since Taxkorgan earthquakes in 1895 and 1896, the Aketao earthquake occurred on the Muji fault on the northern portion of the KES in 2016. Since then, the trend of seismic activities along the KES has been paid much attention to. Based on the visco elastic layered lithosphere model, we calculate the co-seismic and post-seismic stress changes caused by five historical earthquakes on the KES and its adjacent areas since 1895, and analyze the interaction among strong earthquakes. The results show that all of the historical earthquakes after 1895 occurred in the areas where the co-seismic and post-seismic Coulomb stress increased. Coulomb stress loading at the hypocenters of the 1896 Taxkorgan earthquake, the 1974 Markansu earthquake and the 2016 Aketao earthquake were 0.251 MPa, 0.013 MPa and 0.563 MPa, respectively. The three earthquakes were catalyzed by such variations. The historical earthquakes increased the stress state on most segments of the Southern Kungai Mountain fault and Kongur fault along the KES. In particular, we can identify 2 visible earthquake gaps with increasing seismic hazard formed on the Qimugan segment and Bulunkou segment of the KES. The Qimugan section and the Bulunkou section are located at the fault transition zone with concentrated stress and high extension rate, so great attention should be paid to their seismic hazard at present day.

Post-Collisional Ductile Extensional Tectonic Framework in the UHP and HP Metamorphic Belts in the Dabie-Sulu Region, China

The present-day observable tectonic framework of the ultrahigh-pressure (UHP) and high-pressure (HP) metamorphic belts in the Dabie-Sulu region was dominantly formed by an extensional process, mostly between 200 and 170 Ma, following the Triassic collision between the Sino-Korean and Yangtze cratons. The framework that controls the present spatial distribution of UHP and HP metamorphic rocks in particular displays the typical features of a Cordilleran-type metamorphic core complex, in which at least four regional-scale, shallow-dipping detachment zones are recognized. Each of these detachment zones corresponds to a pressure gap of 0.5 to 2.0 GPa. The detachment zones separate the rocks exposed in the region into several petrotectonic units with different P-T conditions. The geometry and kinematics of both the detachment zones and the petrotectonic units show that the exhumation of UHP and HP metamorphic rocks in the Dabie-Sulu region was achieved, at least in part, by non-coaxial ductile flow in the multi-layered detachment zones, and by coaxial vertical shortening and horizontal stretching in the metamorphic units, under amphibolite- to greenschist-facies conditions, and in an extensional regime. All ductile extensional deformations occurred at depths below 10 to 15 km, i.e. below the brittle/ductile deformation transition.

Evaluation model of venture investment based on fuzzy matter-element method of combined weight

An evaluation model of an international venture investment project on the basis of fuzzy matter-element and combined weight methods is introduced. First, the compound fuzzy matter-element of optimal subordinate degree is constructed on the principle of the bigger-more-optimal or the less-more-optimal depending on the actual evaluation indicators, and combined with standard fuzzy matter-element to form a difference-square fuzzy matter-element. Secondly, a combined weight is calculated by both information entropy and the expert grading method. Finally, the compound fuzzy matter-element of Euclidian approach degree by M(·,+)method is constituted and used to classify venture investment projects. Based on the model above, six venture investment projects in a company are evaluated, and the results show that the projects are all good, which is demonstrated by the good income of the projects. Therefore, the coincidence of evaluation results and actual operation status indicates that the model is of great value in practical application.

Forceful Emplacement of Granitic Plutons in an Extensional Tectonic Setting:Syn-kinematic Plutons in the Yagan-Onch Hayrhan Metamorphic Core Complex

It is generally considered that granitic plutons are forcefully emplaced in acompressional setting and permissively emplaced in an extensional setting. This paper, however,shows that syn-kinematic (extensional) elliptic granitic plutons in the Yagan-Onch Hayrhanmetamorphic core complex (MCC) have relatively strong forceful emplacement, which are indicated by(1) concentric distribution of the rock units, (2) a strain pattern with strong strains on themargins and low strains at the centre of a pluton, and particularly (3) syn-emplacement shorteningof the host rocks within the aureole. The strain analysis for the host rocks shows that thehost-rock ductile shortening, i.e. forceful emplacement, provides about 16-24 percent of theemplacement space for the present plutons. All these suggest that forceful emplacement occurs notonly in a compressional tectonic setting, but also in an extensional setting. This study furtherdemonstrates the significance of the multiple emplacement of granitic plutons and provides newinformation about the causality between granitic magmatism and the formation of the MCC and itsdynamics.

Evaluation on Urban Land Ecological Security Based on the PSR Model and Matter-Element Analysis: A Case Study of Zhuhai, Guangdong, China

As one of the Special Economic Zones since the reform and opening up, Zhuhai has developed during the past 30 years. Its economic development, industrial structure and ecological environment have undergone great changes. Research on changes in Zhuhai’s land ecological security is of great significance. Using relevant data from 2007-2012, this study established a land ecological security assessment system based on the PSR conceptual framework model. The system contained 18 indicators from 3 aspects according to the concrete features of Zhuhai. Then we used the matterelement analysis and the improved entropy weight to analyze and evaluate the land ecological security of Zhuhai. The results showed that: from 2007 to 2012, the levels of the land ecological security of Zhuhai were “secure”, and the value increased year by year;as the land ecological security response value increased, Zhuhai was capable of solving land ecosystem problems. However, it should be noted that the structure of land ecosystem in Zhuhai has not formed and that rapid expansion of construction land has caused the shortage of cultivated land and other issues. Measures should be taken to control the construction area, improve land intensive utilization and improve the land ecological security.

Evolution of the Extensional Rifted Yunnan-Guizhou-Guangxi Oceanic Basin During the Late Hercynian to Middle Indosinian Stage

On the basis of exhaustive researches on the facies sequences and depositlonal evolutionary process of various depositional systems, the genetic stratigraphic framework of the extensional rifted oceanic basin, which has undergone strong structural destruction, has been reconstructed by means of dynamic genetic stratigraphic analysis. Five depositional episodes have been distinguished from various isochronous stratigraphic boundaries and stratigraphic sequences with the three-dimensional structure of each depositional episode analysed in detail. The tectonic paleogeographic environment corresponding to different stages of each depositional episode has been reconstructed for individual depositional system tracts. And the evolution history of this rifted basin has been divided into four stages' initial rifting and oceanization of continental crust, stretching and spreading of the basin, subduction and basin differentiation, and convergence and collision. A NNE-trending intracontinental soft collision suture was left after the closing of the basin.

Improved Geometric Model of Extensional Fault–bend Folding

Extensional fault-bend folds, also called rollovers, are one of the most common structures in extensional settings. Numerous studies have shown that oblique simple shear is the most appropriate mechanism for quantitative modeling of geometric relations between normal faults and the strata in their hanging walls. However, the oblique simple shear has a rather serious issue derived from the shear direction, particularly above convex bends. We use geometric and experimental methods to study the deformation of extensional fault-bend folds on convex bends. The results indicate that whether the fault bends are concave or convex, the shear direction of the hanging wall dips toward the main fault. On this basis, we improve the previous geometric model by changing the shear direction above the convex bends. To illustrate basin history, our model highlights the importance of the outer limit of folding instead of the growth axial. Moreover, we propose a new expression for the expansion index that is applicable to the condition of no deposition on the footwall. This model is validated by modeling a natural structure of the East China Sea Basin.