Performance analysis of a new baseline-based SS-Y extensometer

In order to solve the problems in the observation with the SS-Y extensometer, such as background noise and discontinuity of earth tide curve, this paper proposed to improve the stability of the instrument and the smoothness of the earth tide curve by improving the baseline structure of the instrument. In this study, a new φ20*1.2 invar tube was introduced in replacement of the existing φ6 invar rod as the baseline of the instrument and compared with the existing φ6 invar rod on the instrument’s linearity,sensitivity and other indexes. Firstly, the SS-Y extensometers using φ6 invar rod and cp20*1.2 invar tube were tested. Test results were then calculated, and accuracy errors of the instruments based on the two baselines were obtained. Finally, their accuracy errors and earth tide curves were compared. Results showed that, compared with the extensometer based on the existing φ6 invar rod, the extensometer based on the new φ20*1.2 invar tube was superior in performance, with linearity error reducing to 0.495% from 0.937%, sensitivity increasing to 68.65 mV/μm from 65.46 mV/μm, and earth tide curve growing more stable and continuous.

Development of a new differential extensometer

This paper describes a new differential extensometer, which has a baseline rod in suspension with both ends free, and some preliminary test results. Compared with a traditional differential extensometer, which has one end of the baseline rod fixed to the ground, this instrument is less affected by commonly encountered interferences ,including environment vibration, momentary power failure, and power noise.

Characterization of mechanical properties of aluminum cast alloy at elevated temperature

The tensile response, the low cycle fatigue （LCF） resistance, and the creep behavior of an aluminum （A1） cast alloy are studied at ambient and elevated temperatures. A non-contact real-time optical extensometer based on the digital image correlation （DIC） is developed to achieve strain measurements without damage to the specimen. The optical extensometer is validated and used to monitor dynamic strains during the mechanical experiments. Results show that Young＇s modulus of the cast alloy decreases with the increasing temperature, and the percentage elongation to fracture at 100 ℃ is the lowest over the temperature range evaluated from 25 ℃ to 300 ℃. In the LCF test, the fatigue strength coefficient decreases, whereas the fatigue strength exponent increases with the rising temperature. The fatigue ductility at 100 ℃. As expected, the resistance to and changes from 200 ℃ to 300 ℃. coefficient and exponent reach maximum values creep decreases with the increasing temperature

An in situ monitoring campaign of a hard rock pillar at great depth within a Canadian mine

A recent research campaign at a Canadian nickel-copper mine involved instrumenting a hard rock sill drift pillar with an array of multi-point rod extensometers,distributed optical fibre strain sensors,and borehole pressure cells(BHPCs).The instrumentation spanned across a 15.24 m lengthwise segment of the relatively massive granitic pillar situated at a depth of 2.44 km within the mine.Between May 2016 and March 2017,the pillar’s displacement and pressure response were measured and correlated with mining activities on the same level as the pillar,including:(1)mine-by of the pillar,(2)footwall drift development,and(3)ore body stoping operations.Regarding displacements of the pillar,the extensometers provided high temporal resolution(logged hourly)and the optical fibre strain sensors provide high spatial resolution(measured every 0.65 mm along the length of each sensor).The combination of sensing techniques allowed centimetre-scale rock mass bulking near the pillar sidewalls to be distinguished from microstrain-scale fracturing towards the core of the pillar.Additionally,the influence and extent of a mine-scale schistose shear zone transecting the pillar was identified.By converting measured rock mass displacement to velocity,a process was demonstrated which allowed mining activities inducing displacements to be categorised by time-duration and cumulative displacement.In over half of the analysed mining activities,displacements were determined to prolong for over an hour,predominately resulting in submillimetre cumulative displacements,but in some cases multi-centimetre cumulative displacements were observed.This time-dependent behaviour was more pronounced within the vicinity of the plumb shear zone.Displacement measurements were also used to assess selected support member load and elongation mobilisation per mining activity.It was found that a combined static load and elongation capacity of reinforcing members was essential to maintaining excavation stability,while permitting gradual shedding of stress through controlled pillar sidewall displacements.

Monitoring Instrumentation in Underground Structures

Nowadays underground structures are very important. Based on observations of engineering;properties during geotechnical construction are an integral part of the design of underground structures. This research presents instrumentation as a tool to assist with these measurement observations, determine the need for modifications to loading or support arrangement. Also apart from above construction control, instrumentation is also indispensable for site investigation, design verification and safety of the structure. Instrumentation used in the construction of tunnels and subways can be implemented in three stagesbefore, during operation and during operation are examined. Metro Railway Tunnels are constructed in populated area and have a more comprehensive instrumentation and monitoring program that additionally includes monitoring of ground conditions, underground water levels, tilt and settlement of nearby buildings or other structures of interest in the vicinity of the tunnel alignment. Instrumentation monitoring for metro railway tunnels includes monitoring of the structures under construction together with the ground, buildings and other facilities within the predicted zone of influence. Furthermore, instrumentation and subway tunnels in and around them increase accuracy of the different layers of the earth and excavation of the surrounding structures and make safety and accuracy. This paper presents the features of sophisticated instrumentation available today for geotechnical monitoring. A wide range of sophistic have been described with their applications ted electronic and mechanical instrumentation with different instrumentation schemes used to meet the requirements of different types of structures.

Digital image correlation based high-speed crack tip locatingmethod and its application

Based on a digital image correlation（DIC）method with the measurements of a high speed crack＇s displacement and strain fields,a technique to accurately and automatically locate its crack tip has been developed.The crack tip is identified by finding the abrupt jump on the opening（or dislocation）curve of a point on the trace of the crack propagation,while the opening is measured through a virtual extensometer technique and the abrupt jump is identified by finding the peak on the curve.The method was verified using a specially designed experiment and applied to measure the critical crack tip opening angle of a rock sample.Because the involvement of analytical models has been avoided and then the good performance could be ensured for low resolution speckle images,this technique is expected to be very useful in the quantitative study of high speed cracks in experiments using high speed cameras.