Insight into the experiment and extraction mechanism for separating carbazole from anthracene oil with quaternary ammonium-based deep eutectic solvents

Carbazole is an irreplaceable basic organic chemical raw material and intermediate in industry.The separation of carbazole from anthracene oil by environmental benign solvents is important but still a challenge in chemical engineering.Deep eutectic solvents (DESs) as a sustainable green separation solvent have been proposed for the separation of carbazole from model anthracene oil.In this research,three quaternary ammonium-based DESs were prepared using ethylene glycol (EG) as hydrogen bond donor and tetrabutylammonium chloride (TBAC),tetrabutylammonium bromide or choline chloride as hydrogen bond acceptors.To explore their extraction performance of carbazole,the conductor-like screening model for real solvents (COSMO-RS) model was used to predict the activity coefficient at infinite dilution (γ^(∞)) of carbazole in DESs,and the result indicated TBAC:EG (1:2) had the stronger extraction ability for carbazole due to the higher capacity at infinite dilution (C^(∞)) value.Then,the separation performance of these three DESs was evaluated by experiments,and the experimental results were in good agreement with the COSMO-RS prediction results.The TBAC:EG (1:2) was determined as the most promising solvent.Additionally,the extraction conditions of TBAC:EG (1:2) were optimized,and the extraction efficiency,distribution coefficient and selectivity of carbazole could reach up to 85.74%,30.18 and 66.10%,respectively.Moreover,the TBAC:EG (1:2) could be recycled by using environmentally friendly water as antisolvent.In addition,the separation performance of TBAC:EG (1:2) was also evaluated by real crude anthracene,the carbazole was obtained with purity and yield of 85.32%,60.27%,respectively.Lastly,the extraction mechanism was elucidated byσ-profiles and interaction energy analysis.Theoretical calculation results showed that the main driving force for the extraction process was the hydrogen bonding ((N–H...Cl) and van der Waals interactions (C–H...O and C–H...π),which corresponding to the blue and green isosurfaces in IGMH analysis.This work presented a novel method for separating carbazole from crude anthracene oil,and will provide an important reference for the separation of other high value-added products from coal tar.

Experimental investigation on coal pore-fracture variation and fractal characteristics synergistically affected by solvents for improving clean gas extraction

Chemical solvents instead of pure water being as hydraulic fracturing fluid could effectively increase permeability and improve clean methane extraction efficiency.However,pore-fracture variation features of lean coal synergistically affected by solvents have not been fully understood.Ultrasonic testing,nuclear magnetic resonance analysis,liquid phase mass spectrometry was adopted to comprehensively analyze pore-fracture change characteristics of lean coal treated by combined solvent(NMP and CS_(2)).Meanwhile,quantitative characterization of above changing properties was conducted using geometric fractal theory.Relationship model between permeability,fractal dimension and porosity were established.Results indicate that the end face fractures of coal are well developed after CS2and combined solvent treatments,of which,end face box-counting fractal dimensions range from 1.1227 to 1.4767.Maximum decreases in ultrasonic longitudinal wave velocity of coal affected by NMP,CS_(2)and combined solvent are 2.700%,20.521%,22.454%,respectively.Solvent treatments could lead to increasing amount of both mesopores and macropores.Decrease ratio of fractal dimension Dsis 0.259%–2.159%,while permeability increases ratio of NMR ranges from 0.1904 to 6.4486.Meanwhile,combined solvent could dissolve coal polar and non-polar small molecules and expand flow space.Results could provide reference for solvent selection and parameter optimization of permeability-enhancement technology.

Study on the green extraction of corncob xylan by deep eutectic solvent

Corn as one of the world's major food crops,its by-product corn cob is also rich in resources.However,the unreasonable utilization of corn cob often causes the environmental pollution,waste of resources and other problems.As one of the most abundant polymers in nature,xylan is widely used in food,medicine,materials and other fields.Corn cob is rich in xylan,which is an ideal raw material for extracting xylan.However,the intractable lignin is covalently linked to xylan,which increases the difficulty of xylan extraction.It has been reported that the deep eutectic solvent(DES)could preferentially dissolve lignin in biomass,thereby dissolving the xylan.Then,the xylan in the extract was separated by ethanol precipitation method.The xylan precipitate was obtained after centrifugation,while the supernatant was retained.The components of the supernatant after ethanol precipitation were separated by the rotary evaporator.The ethanol,water and DES were collected for the subsequent extraction of corn cob xylan.In this study,a novel way was provided for the green production of corn cob xylan.The DES was used to extract xylan from corn cob which was used as the raw material.The effects of solid-liquid ratio,reaction time,reaction temperature and water content of DES on the extraction rate of corn cob xylan were investigated by the single factor test.Furthermore,the orthogonal test was designed to optimize the xylan extraction process.The structure of corn cob xylan was analyzed and verified.The results showed that the optimum extraction conditions of corn cob xylan were as follows:the ratio of corn cob to DES was 1:15(g:mL),the extraction time was 3 h,the extraction temperature was 60℃,and the water content of DES was 70%.Under these conditions,the extraction rate of xylan was 16.46%.The extracted corn cob xylan was distinctive triple helix of polysaccharide,which was similar to the structure of commercially available xylan.Xylan was effectively and workably extracted from corn cob by the DES method.This study provided a new approach for high value conversion of corn cob and the clean production of xylan.

Research Progress of Deep Eutectic Solvents in Extraction of Plant Flavonoids

As a new type of green solvents,deep eutectic solvents(DESs)have the advantages of strong extraction ability,designability,simple preparation,low price,recoverability and biodegradation,and show great application potential in the field of plant flavonoid extraction.In this paper,the definition,classification and preparation methods of DESs were introduced.The effects of DES composition,molar ratio of DES components,water content of DES systems,liquid-material ratio,extraction temperature,extraction time and extraction auxiliary techniques on the extraction yield of plant flavonoids were expounded.The recycling methods of DESs were summarized.Existing problems of DESs in the field of plant flavonoids extraction were pointed out,and further research direction and trend were analyzed and prospected.

Influence of Solvent onto Chemical Extraction of America-Type Coconut (Coco nucifera L.) Fbers: Analysis of Physicochemical, Mechanical and Morphological Properties

In this study, the natural fibers from Coconuts of the species Coco nucifera L. were Chemically extracted in different solvents such as sodium hydroxide (SH), acetone (AC) and sodium hydroxide-acetone (SHA) for their applications in the textile industries. Structural, morphological and physico-mechanical characterizations such as X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR), scanned electron microscopy (SEM), measurements of density, Young’s modulus, water absorption rate and humidity were evaluated. The XRD and FTIR results show that Coco nucifera L. fibers contains type I cellulose. Mechanical characterizations were also carried out. These results show that by varying the different solvents used, the physico-chemical, mechanical and morphological properties of the fibers change, which implies that the solvent has an influence on the properties of these fibers. The fibers extracted by the sodium hydroxide-acetone mixture have a linear density of 1.636, the percentage of water absorption is 62.428%, the percentage of moisture absorption 9.605% compared to other values in the literature shows that this solvent mixture improves the properties of coconut fibers which contain type I cellulose. The tensile stress is 0.013 GPa, the percentage strain is 49.836% and the Young’s modulus is 0.114 GPa as well as the percentage elongation show that these fibers are elasto-plastic. The values obtained mean that these fibers are suitable for use in textiles.

Efficient and selective extraction of sinomenine by deep eutectic solvents

Sinomenine is the main bio-active ingredient of Sinomenii Caulis and usually produced by solventextraction techniques. However, the extraction of sinomenine suffers from the lack of highly efficient and environmentally-benign solvents. In this work, deep eutectic solvents(DESs) based on fragrances were synthesized, hydrogen-bond donors(HBDs) and hydrogen-bond acceptors(HBAs) components of DESs were identified and their extraction ability for sinomenine was evaluated and the extraction conditions were optimized by single-factor and orthogonal design experiments. It was found that the hydrogen-bonding interaction between sinomenine and DESs was the main extraction driving force and there was no explicit relationship between the extraction ability and the hydrophobicity of the DESs. The DESs could be recycled and sinomenine could be recovered quantitatively via backextraction. High-purity sinomenine((95.0 ± 2.3)%) could be produced. These findings suggest that DESs are highly-effective solvents for the isolation of sinomenine and exhibit great potential for the extraction of other bio-active compounds.

Liquid–liquid extraction of levulinic acid from aqueous solutions using hydrophobic tri-n-octylamine/alcohol-based deep eutectic solvent

Levulinic acid(LA)is one of the top-12 most promising biomass-based platform chemicals,which has a wide range of applications in a variety of fields.However,separation and purification of LA from aqueous solution or actual hydrolysate continues to be a challenge.Among various downstream separation technologies,liquid-liquid extraction is a low-cost,effective,and simple process to separate LA.The key breakthrough lies in the development of extractants with high extraction efficiency,good hydrophobicity,and low cost.In this work,three hydrophobic deep eutectic solvents(DESs)based on tri-n-octylamine(TOA)as hydrogen bond acceptor(HBA)and alcohols(butanol,2-octanol,and menthol)as hydrogen bond donors(HBDs)were developed to extract LA from aqueous solution.The molar ratios of HBD and HBA,extraction temperature,contact time,solution pH,and initial LA concentration,DES/water volume ratios were systematically investigated.Compared with 2-octanol-TOA and menthol-TOA DES,the butanol-TOA DES exhibited the superior extraction performance for LA,with a maximum extraction efficiency of 95.79±1.4%.Moreover,the solution pH had a great impact on the LA extraction efficiency of butanol-TOA(molar ratio=3:1).It is worth noting that the extraction equilibrium time was less than 0.5 h.More importantly,the butanol-TOA(3:1)DES possesses good extraction abilities for low,medium,and high concentrations of LA.

Effect of Temperature on Extraction of Castor Oil from Castor Seeds Using Potential Green Solvents

Extraction of castor oil from castor seeds was investigated using different green solvents which include d-limonene, p-cymene, α-pinene, ethanol, and furfural at the temperature range of (323 - 413) K. The Soxhlet extraction method was employed to investigate the effect of temperature at atmospheric pressure. The focus of the study was to investigate a potential green solvent that can produce the high yields compared to the traditional solvent (hexane). The results show that at the average time of 3 hours and 30 minutes, the castor oil yield for green solvents were ranked as furfural (47.13%) > ethanol (45.37%) > p-cymene (39.15%) > d-limonene (39.13%) > α-pinene (38.11%). These castor oil yields were obtained at optimum temperatures for each green solvent. The castor oil yields were compared to the yield of hexane (31.36%) at same average time. The green solvents were recovered by using simple distillation, except furfural which was difficult to be recovered.

Extraction of Cinnamomum longepaniculatum deciduous leaves essential oil using solvent-free microwave extraction: Process optimization and quality evaluation

The optimal process conditions for solvent-free microwave extraction(SFME)of essential oils from Cinnamomum longepaniculatum deciduous leaves after moisture conditioning were established by response surface methodology(RSM).A Box-Behnken design(BBD)was applied to evaluate the effects of three independent variables:moisture content(A:54%–74%),microwave power(B:300–500 W)and microwave time(C:20–40 min),on the extraction yield of essential oil.The compounds of the essential oils obtained by SFME,hydro-distillation and microwaveassisted hydro-distillation(MADE)were identified by gas chromatography-mass spectrometry(GC-MS),and the total lipids of C.longepaniculatum fresh leaves and deciduous leaves were analyzed.The correlation analysis of the response regression model indicated that quadratic polynomial model could be employed to optimize the extraction of essential oil.The optimal extraction condition was A:58%,B:400 W and C:28 min.In the optimal condition,the maximum extraction yield was 4.475 mL/100 g dw and higher than that by MADE.The main compound of the essential oil was eucalyptol(63.54%),and total oxygenated compounds was 78.95%,mainly caused by SFME and the metabolism of endophytic bacteria with decreasing content of phospholipids and fatty acids.Analysis of variance under the extraction condition illustrated high fitness of the model and the success of RSM for optimizing and reflecting the expected process condition.SFME combined with moisture regulation was an effective method for extracting essential oil from C.longepaniculatum deciduous leaves.

Removal of chromium(Ⅲ) from aqueous waste solution by predispersed solvent extraction

The extraction experiments of chromium（W） from aqueous waste solution by predispersed solvent extraction （PDSE） process with extractant （HEHPEHE） and its mixture, including acidic extractant （D2EHPA）, alkaline extractant （TOA） and neutral extractant （TBP） were carried out respectively. It is found that the extractant HEHPEHE exhibited high extraction selectivity to chromium（III） from aqueous waste solution. The colloidal liquid aphrons （CLAs） were successfully generated using kerosene as a solvent, HEHPEHE as an extractant, sodium dodecyl benzene sulphate （SDBS） as a surfactant in aqueous phase and polyoxyethylene sorbitol anhydride monolaurate （Tween-20） in oil phase. To study the extraction efficiency and advantages of the PDSE process in the removal of chromium（III）, the effects of major factors, such as initial chromium（III） concentration, volume of colloidal gas aphrons （CGAs）, HEHPEHE volume fraction, phase ratio （solvent phase to water phase）, mass fraction of dodecyl trimethylammonium bromide （HTAB）, mass fraction of SDBS, mass fraction of Tween-20 and initial pH of aqueous waste solution were also investigated and the appropriate process conditions were obtained. Under the appropriate conditions, the extraction efficiency of chromium（III） above 99.9 % can be achieved and the treated aqueous waste solution can be discharged directly without polluting the environment.

Predictive methods for density and refractive index of naphthenic lubricating oils during solvent extraction process

Lubricating oils are usually produced by solvent extraction to separate aromatics in order to achieve the desired specifications and better quality products.Among the different properties of lubricating oils,density and refractive index are some of the most important properties which can both be used for petroleum fluid characterization.Predictions of density and refractive index for naphthenic oils during solvent extraction by DMSO obtained by the pseudo-component approach and the quadratic correlation were both examined.The pseudo-component approach is a method to predict density and refractive index from composition while the latter merely relates density to refractive index.Results indicated that the predictions yielded by the pseudo-component method were in good agreement with experimental data for naphthenic oils.And the use of a function of refractive index(FRI_(20))as a pseudo-component property remarkably improved n_(20)predictions for the naphthenic mixtures.However,the density and refractive index predictions obtained by the quadratic correlation exhibited significantly higher de-viations for naphthenic oils than those for paraffinic oils.Thus a new modified correlation of the same functional form was proposed for naphthenic oils.The modification significantly improved predictions for naphthenic oils,which presented similar accuracy as the pseudo-component approach.And the previous correlation was still used for paraffinic oils.Additionally,effect of temperature on density and refractive index of naphthenic oils was examined.Results showed that the modified quadratic correlation was accurate for describing the relationship between density and refractive index of naphthenic oils at 20-90℃.The temperature dependence of density and refractive index for the raffinates and the extracts could be accurately described by the thermal coefficients for saturates and aromatics,respectively.Regarding the refractive index variation of the extracts with temperature,the empirical equation was proved to be a better option compared with the method using the thermal coefficient for aromatics.

Extraction of Organochlorine Pesticides in Sediments Using Soxhlet,Ultrasonic and Accelerated Solvent Extraction Techniques

The application of soxhlet, ultrasonic and accelerated solvent extractiontechniques to the analysis of six organochlorine pesticides (α-HCH, β-HCH, γ-HCH, o, p'-DDT,p,p'-DDT and p,p'-DDE) in Taihu Lake sediment samples is described. It was found that the limits ofquantification ranged from 0.002 μg g^(-1) to 0.004 μg g^(-1), and the recoveries oforganochlorine pesticides with the three extraction techniques were acceptable ( 】80.7%). With amass selective detector, better results were obtained by accelerated solvent extraction usinghexane-acetone (1:1) as compared with soxhlet and ultrasonic extraction. It was shown that theaccelerated solvent extraction was the optimum technique for the analysis of organochlorinepesticides in sediments. The general features of the three extraction techniques are also presented.

Separation of nickel, cobalt and copper by solvent extraction with P204

Nickel, cobalt and copper were separated by solvent extraction with P204. The experimental results show that [Co(NH 3) 6] 3+ is an inert complex in extraction kinetics, therefore cobalt can be separated from nickel and copper by non equilibrium solvent extraction. Under the conditions of temperature 25?℃, contact time of two phases 10?min, phase ratio 1∶1, aqueous pH 10.10 and concentration of P204 20%, [Co(NH 3) 6] 3+ is hardly extracted by P204, while the percentage extractions of nickel and copper are 79.3% and 93.9% respectively. Nickel and copper are separated by equilibrium solvent extraction with P204. Under the conditions of temperature 25?℃, contact time of two phases 1?min, phase ratio 1∶1, equilibrium pH 4.01 and concentration of P204 20%, the separation factor of copper and nickel is 216.

Prediction of dispersed phase holdup in pulsed disc and doughnut solvent extraction columns under different mass transfer conditions

Using experimental data from a number of pulsed disc and doughnut solvent extraction columns, a unified correla- tion for the prediction of dispersed phase holdup that considers the effects of mass transfer is presented. Pulsed disc and doughnut solvent extraction columns （PDDC） have been used for a range of important applications such as ura- nium extraction and nuclear fuel recycling. Although the dispersed phase holdup in a PDDC has been presented by some researchers, there is still the need to develop a robust correlation that can predict the experimental dispersed phase holdup over a range of operating conditions including the effects of mass transfer direction. In this study, dis- persed phase holdup data from different literature sources for a PDDC were used to refit constants for the correlation presented by Kumar and Hartland lind. Eng. Chem. Res.,27 （1988）,131-138] which did not consider the effect of col- umn geometry. In order to incorporate the characteristic length of the PDDC （i.e. the plate spacing）, the unified cor- relation for holdup proposed by Kumar and Hartland based on data from eight different types of columns [Ind. Eng. Chem. Res.,34 （1995） 3925-3940] was refitted to the PDDC data. New constants have been presented for each hold- up correlation for a PDDC based on regression analysis using published holdup data from PDDCs that cover a range of onerating conditions and nhwical nronerties and consider the direction of mass transfer.

Recovery of Li_(2)CO_(3)and FePO_(4)from spent LiFePO_(4)by coupling technics of isomorphic substitution leaching and solvent extraction

Efficient and low-cost recycling of spent lithium iron phosphate(LiFePO_(4),LFP)batteries has become an inevitable trend.In this study,an integrated closed-loop recycling strategy including isomorphic substitution leaching and solvent extraction process for spent LFP was proposed.An inexpensive FeCl_(3)was used as leaching agent to directly substitute Fe^(2+)from LFP.99%of Li can be rapidly leached in just 30 min,accompanied by 98%of FePO_(4)precipitated in lixivium.The tri-n-butyl phosphate(TBP)-sulfonated kerosene(SK)system was applied to extract Li from lixivium through a twelve-stage countercurrent process containing synchronous extraction and stepwise stripping of Li^(+)and Fe^(3+).80.81%of Li can be selectively enriched in stripping liquor containing 3.059 mol·L^(-1)of Li^(+)under optimal conditions.And the Fe stripping liquor was recovered for LFP re-leaching,of which,Fe^(2+)was oxidized to Fe^(3+)by appropriate H_(2)O_(2).Raffinate and lixivium were concentrated and entered into extraction process to accomplished closeloop recycling process.Overall,the results suggest that more than 99%of Li was recovered.FeCl_(3)holding in solution was directly regenerated without any pollutant emission.The sustainable mothed would be an alternative candidate for total element recycling of spent LFP batteries with industrial potential.

Simulation of Solvent Extraction for Naphthenic Lubricating Base Oils

Solvent extraction is the process of separating aromatics from vacuum distillates for the production oflubricating base oils. In this study, the authors use dimethyl sulfoxide (DMSO) instead of furfural as solvent, in light of itshigher selectivity, to obtain extracts with a high aromatic content for naphthenic lubricating base oils. We systematicallyinvestigated effects of the solvent-to-oil (S/O) ratio and extraction temperature on the yield of the extract, efficiency ofaromatic removal, and composition of the extracts and raffinates. The results showed that the aromatic content of extractsfor naphthenic oils could reach a high value of about 80%. The solvent maintained a high selectivity for aromatics fornaphthenic oils even under a high S/O ratio and a high extraction temperature. Moreover, the efficiency of aromatic removalfor naphthenic lubricating base oils could be enhanced by increasing either the S/O ratio or the extraction temperature,although these measures had limited effects in practice. Following this, we used the non-random two-liquid (NRTL) modelbased on the pseudo-component approach to simulate the liquid-liquid equilibrium of the system of DMSO + naphtheniclubricating base oils, and determined the parameters of binary interaction through regression based on the data on phaseequilibrium. The modeling results showed that the predicted yield, content of the solvent, and composition of the raffinatesand extracts were in good agreement with those obtained in the experiments. This validates the reliability of the model usedto represent the DMSO + naphthenic lubricating base oil system. Both the experimental data and the method of simulationreported here can help optimize the extraction of naphthenic lubricating base oils, and provide a better understanding of thecorresponding process.

Study on Extraction of Tea Saponin from Camellia oleifera Cake Using Water as Extraction Solvent

This paper studied the effects of liquid-solid ratio, temperature, time and pH value on the extraction rate of tea saponin from the cake of Camellia oleifera seeds by using single factor experiment with the cake of Camellia oleifera seeds as the raw materials, and water as the extraction solvent, and orthogonal test was used to determine the optimal extraction process conditions. The results showed that the extraction ratio of tea saponin could reach up to 95.50% when the liquidsolid ratio was 11：1, extracting temperature of 80 ℃, extraction time of 6 h, and pH value of 9.

The use of environmentally sustainable bio-derived solvents in solvent extraction applications——A review

Replacement of volatile organic compounds （VOCs） by greener or more environmentally sustainable solvents is becoming increasingly important due to the increasing health and environmental concerns as well as economic pressures associated with VOCs. Solvents that are derived from biomass, namely bio-derived solvents, are a type of green solvent that have attracted intensive investigations in recent years because of their advantages over con- ventional VOCs, such as low toxicity, biodegradability and renewability. This review aims to summarize the use of bio-derived solvents in solvent extraction applications, with special emphasis given to utilization of biodiesels and terpenes. Compared with the conventional VOCs, the overall performance of these bio-derived solvents is comparable in terms of extraction yields and selectivity for natural product extraction and no difference was found for metal extraction. To date most researchers have focused on laboratory scale thermodynamics studies. Future work is required to develop and test new bio-derived solvents and understand the kinetic performance as well as solvent extraction nilnt nlant studies.

Deep eutectic solvents and alkaline extraction of protein from seabuckthorn seed meal: a comparison study

Seabuckthorn seed meal(SSM) is a waste of oil extraction industry that rich in protein. In order to seek suitable protein extraction method, three different deep eutectic solvents(DESs)(including choline chlorideglycerol, choline chloride-oxalic acid and choline chloride-urea) were developed for extracting protein from SSM and compared with alkaline. Result indicated that alkaline could effectively extract 56.9% protein from SSM and its protein content was 73.1%, higher than DES at 31.0%-41.4% and 64.3%-67.5%, respectively. However, compared to alkali, DES led to a product with less β-sheet, more β-turn, more essential amino acids, higher total amino acid content, especially choline chloride-urea which extracted protein showing an integrated and similar protein weight distribution compared to SSM. Also, this protein extracted chloride-urea showed a highest digestibility in vitro(by pepsin)(54.2%). These results indicated that choline chloride-urea extraction is better than alkaline extraction for SSM.

Simultaneous Determination of Four Estrogens in Compost Based on Ultrasonic Solvent Extraction, Solid-Phase Extraction Clean-Up and Analysis by UHPLC-MS/MS

A rapid, cost effective and reliable analytical method was developed and validated for the simultaneous determination of four estrogens (17 β-estradiol, 17 α-ethinylestradiol, estrone, and estriol) in compost samples from the biodegradation of biological infectious hazardous wastes. Ultrasonic solvent extraction, using methanol as extraction solvent, coupled with SPE clean-up, using cartridges HLB 60 mg - 6 ml Supelco® and acetonitrile for reconstitution of eluents, was used for the simultaneous extraction of the four estrogens. Mean recoveries in the range of 98% - 107% were obtained. All compounds were separated in a single gradient run by UHPLC KinetexTM 2.6 μm XB-C18 100 ÅLC (50 × 4.6 mm) column. Analytes were detected via multiple reaction monitoring (MRM) using an AB SCIEX API-5000TM triple quadrupole (Applied Biosystems/MDS SCIEX) with electrospray ionization in negative mode. Isocratic mobile phase of Water:ACN (50:50) resulted to be the optimum. Limits of detection and quantification were on the order of 0.66 ng·g-1 and 2 ng·g-1 for all the estrogens. These limits were lower than most of the values reported in the literature for similar matrices. Suitable level of linearity, good repeatability and reproducibility with coefficients of variation is lower than 11.7%, 6.8% and 8.3%, respectively.