Surface Plasmon Interference Lithography Assisted by a Fabry-Perot Cavity Composed of Subwavelength Metal Grating and Thin Metal Film

A surface plasmon interference lithography assisted by a Fabry-Perot （F-P） cavity composed of subwavelength metal gratings and a thin metal fihn is proposed to fabricate high-quality nanopatterns. The calculated results indicate that uniform straight interference fringes with high contrast and high electric-field intensity are formed in the resist under the F-P cavity. The analyses of spatial frequency spectra illuminate the physical mechanism of the formation for the interference fringes. The influence of the F-P cavity spacing is discussed in detail. Moreover, the error analyses reveal that all parameters except the metal grating period in this scheme can bear large tolerances for the device fabrication.

An Ultraviolet Fiber Fabry-Perot Cavity for Florescence Collection of Trapped Ions

We demonstrate a fiber Fabry-Pérot cavity in the ultraviolet range, which covers the florescence wavelength for the 2P to 2S transition of Yb and is designed in the bad cavity limit for florescence collection. Benefiting from both the small cavity mode volume and the large atom dipole, a cavity with moderate finesse and high transmission still supports a good cooperativity, which is made and tested in experiment. Based on the measured experimental parameters, simulation performed on the cavity and ion shows a Purcell factor better than 2.5 and a single-mode fiber collection efficiency over 10%. This technology can support ultra-bright single photon sources based on trapped ions and can provide the possibility to link remote atoms as a quantum network.

Improved Directivity of an OAM Antenna by a Fabry-Perot Cavity: An Experimental Study

The circular phased antenna array is commonly used for generating waves bearing Orbital Angular Momentum (OAM) in the radio frequency band, but it achieves a relatively low directivity. To overcome this drawback, we present here a method to improve the directivity of an OAM circular phased antenna array by embedding it inside a Fabry-Perot cavity. The Fabry-Perot cavity contains three main parts: a partially reflecting surface (PRS), an air cavity and a ground plane. Simulation data show that the directivity of this new OAM antenna achieves an improvement of 8.2 dB over the original array. A prototype is realized and characterized. The simulated and measured characteristics are in good agreement.

Low insertion loss silicon-based spatial light modulator with high reflective materials outside Fabry–Perot cavity

The extinction ratio and insertion loss of spatial light modulator are subject to the material problem, thus limiting its applications. One reflection-type silicon-based spatial light modulator with high reflective materials outside the Fabry-Perot cavity is demonstrated in this paper. The reflectivity values of the outside-cavity materials with different film layer numbers are simulated. The reflectivity values of 6-pair Ta2O5/SiO2 films at 1550 nm are experimentally verified to be as high as 99.9%. The surfaces of 6-pair Ta2O5/SiO2 films are smooth: their root-mean-square roughness values are as small as 0.53 nm. The insertion loss of the device at 1550 nm is only 1.2 dB. The high extinction ratio of the device at 1550 nm and 11 V is achieved to be 29.7 dB. The spatial light modulator has a high extinction ratio and low insertion loss for applications.

光纤压力传感器测量的最小偏差腔长解调算法

在光纤传感技术领域应用基于法珀腔(外腔式法布里-珀罗干涉腔)结构的光纤压力传感器进行气体压力测量时,由于传感器结构决定了腔长动态范围相对较小,需要高分辨率的腔长测量方法。因此针对基于法珀腔结构的光纤压力传感器进行绝对腔长解调算法研究,提出一种高精度最小偏差腔长解调算法,通过将法珀腔光纤压力传感器密封在压力标准源中,对等间隔压力变化产生的不同腔长进行实时解调,实现了气体压力的实时测量。实验结果表明,法珀腔光纤压力传感器腔长值随压差变化呈现出良好的线性关系和重复性,腔长测量的重复性为±1 nm,精度为0.1496%,压力测量的重复性为0.12%,压力测量的精度优于0.5%。

Recent Progress in Multiparameter Measurement Based on Extrinsic Fiber-Optic Fabry-Perot Interferometers and Fiber Gratings

This paper presents a review of recent progress in simultaneous measurement of multiparameters including strain, temperature, vibration, transverse load, based on the combinations of extrinsic fiber-optic Fabry-Perot interferometers and fiber gratings.

基于非本征光纤F-P腔的低压传感器研究

介绍一种基于非本征F-P腔（extrinsic Fabry-Perot cavity）的干涉／强度调制型光纤低压传感器。给出低压传感探头的结构设计和测量原理。利用石英膜片对光纤EFPI压力传感头进行压力测量灵敏度放大；通过不同谱宽的两路光信号的自补偿运算，提高系统的稳定性和抗干扰性。该传感器在0～1．5×10^5Pa的压力测量量程内，压力变化最小分辨率达到50Pa，在连续15h的动态测量下，测量偏差为0．1％FS。

腹腔灌注顺铂加恩度联合体外热疗治疗恶性腹水对照研究

目的 探讨腹腔灌注顺铂加恩度联合体外热疗治疗恶性腹水患者的临床疗效和安全性.方法 将66例恶性腹水患者按随机数字表法分为观察组（33例）和对照组（33例）,两组均予以腹腔灌注顺铂加恩度治疗,观察组联合体外热疗,观察2个月.治疗前后检测腹水和血清血管内皮生长因子水平的变化,比较两组临床疗效、治疗后患者耐受性及不良反应发生率.结果 观察组有效率为90.9%,对照组为69.7%,观察组显著高于对照组（χ2=4.69,P〈0.05）;治疗后两组腹水和血清血管内皮生长因子水平均较治疗前显著下降（P〈0.01）,观察组显著低于对照组（P〈0.01）;两组耐受情况、不良反应发生率比较差异无统计学意义（P〉0.05）.结论 腹腔灌注顺铂加恩度联合体外热疗治疗恶性腹水疗效显著,能有效降低腹水、血清中血管内皮生长因子水平,抗肿瘤作用更强,耐受性、安全性高,优于单纯腹腔灌注顺铂加恩度治疗.

动态F-P腔对波长的解调方法

提出一种动态非本征法布里-珀罗(F-P)腔对波长的解调方法。利用PZT构建的动态非本征F-P腔调制FBG反射光,理论分析得到调制光强随F-P腔长呈类余弦变化。经数值模拟,当PZT在一正弦电压驱动下,F-P腔调制输出的类余弦信号因FBG波长漂移而产生峰值偏移,且偏移量与FBG波长变化量成线性关系,此关系可用于FBG波长的解调。研究结果表明,动态非本征F-P腔波长解调方法,在FBG传感测量中简化了信号处理过程中复杂的算法问题。

Dual-band simultaneous lasing in MOFs single crystals with Fabry-Perot microcavities

Multi-band microlasers based on single microcrystalline materials with Fabry-Perot(F-P) cavities are critically and technologically essential. Here, we demonstrate simultaneous dual-band lasing output(615 and 685 nm) in metal-organic frameworks(MOFs) and organic dyes hybrid single crystals, which support F-P resonances. Through a two-step assembly strategy, two different types of cationic pyridinium hemicyanine dye molecules can be encapsulated into the channel pores of anionic bioMOF-1-2 Me successfully. In addition, the employment of the host-guest system significantly increases the dye loading, enhances luminescent efficiency, and diminishes the aggregation-caused quenching(ACQ) effect in the resultant MOFs/dye composites.This finding not only combines the characteristic of MOFs materials with excellent luminescent properties of organic dyes, but also points out a simple and promising strategy to design multi-band microlasers based on F-P mechanism, opening a low-cost avenue for the rational design of miniaturized lasers in the future.

Design of Fiber Magnetic Field Sensor Based on Fiber Bragg Grating Fabry-Perot Cavity Ring-Down Spectroscopy

A novel fiber magnetic sensor based on the fiber Bragg grating Fabry-Perot （FBG-FP） cavity ring-down technique with pulse laser injection is proposed and demonstrated theoretically. A general expression of the intensity of the output electric field is derived, and the effect of the external magnetic field on the ring-down time is discussed. The results show that the output light intensity and the ring-down time of the FBG-FP cavity are in the inverse proportion to the magnitude of the external magnetic field. Our results demonstrate the new concept of the fiber magnetic sensor with the FBG-FP cavity ring-down spectroscopy and the technical feasibility.

Study of the characteristics of concentration sensing based on FBG Fabry-Perot cavity

Fiber Bragg grating Fabry-Perot (FBG F-P) cavity is used as the sensing model to measure the refractive index of the liquid solution. The cladding of the fiber, which is used as the F-P cavity, is etched by HF solution to enhance the sensitivity to the external refractive index. The experimental results show that with the concentration change of the external solution, the effective refractive index of etched fiber will change, thus the spectra of FBG F-P cavity will appear a spilt point. The relationship between the wavelength at spilt point and the effective refractive index of etched fiber is approximately linear, and also periodical. The sensing model is theoretically analyzed based on transfer matrix method, and the corresponding mathematic model is established.

Loss Measurement of High-Finesse Fabry-Perot Cavities

The loss of a high-finesse Fabry-Perot cavity was measured using frequency scan and cavity ring-down techniques.Different transverse modes were examined by sweeping the frequency of the laser across the corresponding resonances.In addition,cavity ring-down technique was used to measure the loss of the Fabry-Perot cavity and a simple model was employed to remove the influence of finite response time of the optical switch and the detection circuit.

Analysis of Focusing Orbital Angular Momentum Wave Using Fabry-Perot Cavity

One of the biggest obstacles to the application of orbital angular momentum(OAM)in the microwave field is its divergence problem.This paper presents a full analysis of generating and focusing OAM waves using original and improved Fabry-Perot(F-P)cavities.Utilizing combination of microstrip antenna and original F-P cavity,the gain of the OAM antenna is enhanced from 4.0 dBi to 9.3 dBi and the corresponding divergence angle is decreased from 41to 24.To further improve the performance of the OAM antenna,the improved F-P cavity is introduced.The simulated results show that the gain is further enhanced to 12.0 dBi and the divergence angle is further decreased to be 15.

THE NEW BEHAVIOR OF BIFURCATION AND CHAOS IN A NONLINEAR FABRY-PEROT CAVITY

Ⅰ. INTRODUCTION In a Fabry-Perot cavity, there exist two electric fields, which propagate in the counter direction and interact with each other via the absorber, so that the theoretical analysis of the Fabry-Perot system is very complicated. On account of this, many authors had focused their attention on the ring cavity, a considerably simple system. It was proposed as a

High-sensitivity refractive index sensors based on Fano resonance in a metal-insulator-metal based arc-shaped resonator coupled with a rectangular stub

A metal-insulator-metal(MIM)-based arc-shaped resonator coupled with a rectangular stub(MARS) structure is proposed. This structure can generate two tunable Fano resonances originating from two different mechanisms. The structure has the advantage of being sensitive to the refractive index, and this feature makes it favorable for application in various microsensors. The relationship between the structural parameters and Fano resonance is researched using the finite element method(FEM) based on the software COMSOL Multiphysics 5.4. The simulation reveals that the sensitivity reaches1900 nm/refractive index unit(RIU), and the figure of merit(FOM) is 23.75.

Fibre Optic Protection System for Concrete Structures

The design concepts, modelling and implementation of various fibre optic sensor protection systems for development in concrete structures were investigated. Design concepts and on-site requirements for surface-mounted and embedded optical fibre sensor in concrete were addressed. Finite element （FE） modelling of selected sensor protection systems in strain-transfer efficiency from the structure to the sensing region was also studied. And experimental validation of specified sensor protection system was reported. Results obtained indicate that the protection system for the sensors performs adequately in concrete environment and there is very good correlation between results obtained by the protected fibre optic sensors and conventional electrical resistance strain gauges.

Theoretical analysis of transmission characteristics for all fiber,multi-cavity Fabry-Perot filters based on fiber Bragg gratings

The characteristics of transmission spectra for the all fiber, multi-cavity Fabry- Perot （FP） configuration based on fiber Bragg gratings （FBG） are theoretically analyzed and modeled. The general transmission matrix function for the structure with any number of cavities is derived, and explicit expression of the power trans- mission coefficient for symmetrical two-cavity FP is presented. The general condi- tions for flat-top single resonant peak at the central wavelength in FBG stop band are derived and verified in the numerical simulation section. The transmission peaks of single-cavity and two-cavity FP structures are compared and discussed, and results show that compared to the single-cavity FP, flatness of the top and steepness at the edge of transmission peak can be improved by introducing one more cavity. The resonant transmission peak properties of two-cavity structure are investigated in detail for various values of cavity length and FBGs with different reflection characteristics, and the design guidelines for transmission-type filters are presented. The results show that the steepness of peak slope can be improved by increase of FBG reflectivities, and these kinds of filters can be used as nar- row-band single-channel selectors and multi-channel wavelength de-multiplexing by properly choosing the length of cavities and reflectivities of FBGs.

A Novel Analytical Approach for Multi-Layer Diaphragm-Based Optical Microelectromechanical-System Pressure Sensors

An optical microelectromechanical-system （MEMS） pressure sensor based on multi-layer circular diaphragm is described and analysed by using the proposed novel analytical approach and the traditional transfer matrix method. The analytical expressions of the deflection of multi-layer diaphragm and absolute optical reflectance are derived respectively. The influence of residual stress on the deflection of diaphragm is also analysed. Simulation results given by the finite element method are consistent with the ones which are analysed by using the analytical approach. The analytical approach will be helpful to design and fabricate the optical MEMS pressure sensors with multi-layer diaphragm based on Fabry-Perot interferometry.

Highly Angular Tolerant Transmission Filters for Narrow-Band Image Sensors

A dielectric transmittance filter composed of subwavelength grating sandwiched between two few-layers distributed Bragg reflectors (DBRs) is proposed with the aim of being compatible with CMOS technology and to be tunable by lithographic means of the grating pattern without the need of thickness changes, in the broad spirit of metamaterials. The DBR mirrors form a Fabry-Perot (FP) cavity whose resonant frequency can be tuned by changing the effective refractive index of the cavity, here, by tailoring the in-plane filling factor of the grating. The structure has been studied and designed by performing numerical simulations using Fourier Modal Method (FMM). This filter proves to have high broad angular tolerance up to ±30˚. This feature is crucial for evaluating the spectral performance of narrow-band filters especially the so-called Ambient light sensors (ALS). By analyzing the transmittance spectral distributions in the band diagram, it is found that the angular tolerance is due to coupling between the FP and the guided mode inside the cavity in analogy to resonances occurring within multimode periodic waveguides in a different context.