The transient liquid phase diffusion bonding of Si 3N 4 ceramics with Ti/Ni/Ti and Al/Ti/Al multiple interlayers was performed. The formation of intermetallic compounds in situ and their effects on the joints streng...The transient liquid phase diffusion bonding of Si 3N 4 ceramics with Ti/Ni/Ti and Al/Ti/Al multiple interlayers was performed. The formation of intermetallic compounds in situ and their effects on the joints strengths were investigated. The Ti/Ni/Ti interlayers produce NiTi and Ni 3Ti layers with considerable room temperature ductility and high elevated temperature strength to strengthen the bonding zone metals and the joints. The joints with 142 MPa shear strength at room temperature and 88 MPa shear strength at 800 ℃ are achieved under appropriate parameters, respectively. Al/Ti/Al interlayers transform into a special bonding zone metal with a large amount of Al 3Ti particles and a small amount of Al based solid solution, and in this case, the joints are strengthened significantly. Their strengths at room temperature and 600 ℃ reach 90 MPa and 30 MPa, respectively.展开更多
Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂ca...Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂casting-rolling compound forming technology＂ is researched by taking the typical 42CrMo slew bearing as object. Through theoretical analysis, the design criteria of the main casting-rolling forming parameters are put forward at first. Then the constitutive relationship model of as-cast 42CrMo steel and its mathematical model of dynamic recrystallization are obtained according to the results of the hot compression experiment. By a coupled thermal-mechanical finite element model for radial-axial rolling of bearing ring, the fraction of dynamic recrystallization is calculated and recrystallized grains size are predicated. Meanwhile, the effects of the initial rolling temperature and feed rate of idle roll on material microstructure evolution are analyzed. Finally, the industrial rolling experiment is designed and performed, based on the simulation results. In addition, mechanical and metallographic tests are conducted on rolled bearing ring to get the mechanical parameters and metallographic structure. The experimental data and results show that the mechanical properties of bearing ring produced by casting-rolling compound forming technology are up to industrial standard, and a qualified bearing ring can be successfully formed by employing this new technology. Through the study, a process of forming large bearing ring directly by using casting ring blank is obtained, which could provide an effective theoretical guidance for manufacturing large ring parts. It also has an edge in saving material, lowering energy and improving efficiency.展开更多
This study examined the release characteristics of different N forms in an uncoated slow/controlled-release compound fertilizer （UCRF） and the N uptake and N-use efficiency by rice plants. Water dissolution, soil le...This study examined the release characteristics of different N forms in an uncoated slow/controlled-release compound fertilizer （UCRF） and the N uptake and N-use efficiency by rice plants. Water dissolution, soil leaching, and pot experiments were employed. The dynamics of N release from the UCRF could be quantitatively described by three equations： the first-order kinetics equation [N1=N0 （1-e^-kt）], Elovich equation （N1=a ＋ blnt）, and parabola equation （N1=a ＋ bt^0.5）, with the best fitting by the first-order kinetics equation for different N （r= 0.9569^＊＊-0.9999^＊＊）. The release potentials （No values estimated by the first-order kinetics equation） of different N in the UCRF decreased in the order of total N 〉 DON 〉 urea-N 〉 NH4^＋-N 〉 NO3^-N in water, and total N 〉 NH4^＋-N 〉 DON 〉 urea-N 〉 NO3^--N in soil, respectively, being in accordance with cumulative amounts of N release. The constants of N release rate （k values and b values） for different N forms were in decreasing order of total N 〉 DON 〉 NH4^＋-N 〉 NO3^--N in water, whereas the k values were urea- N 〉DON 〉 NH4^＋-N 〉 total N 〉 NO3^--N, and the b values were total N 〉 NH4^＋-N 〉 DON 〉 NO3^--N 〉 urea-N in soil. Compared with a common compound fertilizer, the N-use efficiency, N-agronomy efficiency, and N-physiological efficiency of the UCRF were increased by 11.4%, 8.32 kg kg^-1, and 5.17 kg kg^-1, respectively. The ratios of different N to total N in the UCRF showed significant correlation with N uptake by rice plants. The findings showed that the first-order kinetics equation [Nt=N0 （l-e^kt）] could be used to describe the release characteristics of different N forms in the fertilizer. The UCRF containing different N forms was more effective in facilitating N uptake by rice compared with the common compound fertilizer containing single urea-N form.展开更多
The new results of geologic-structural, petrographic and mineralogic-geochemical researches of Mykert-Sanzheevka ore field—the Uda-Vitim mineragenic zone South-West ending of West Transbaikalia are given. Its main or...The new results of geologic-structural, petrographic and mineralogic-geochemical researches of Mykert-Sanzheevka ore field—the Uda-Vitim mineragenic zone South-West ending of West Transbaikalia are given. Its main ore-controlling structure, represented by losange, consisting of rhombohedral and tetrahedral blocks-duplexes mosaic clusters, which are separated by narrow tectonic sutures, is specified. It is clarified that polycomponent ores clusters are confined with these small-block sutures, made by subvolcanic dykes of shoshonite-latite volcano-plutonic association (233 - 188 million years), apodyke dynamometamorphites (breccias, cataclasite, mylonites) and also mechanometasomatites. Four stages of the dynamometamorphites formation characterized by different species compositions of ore minerals appeared as a result of mechanochemical reactions are determined. A carbonyl model of mineral microaggregates formation with films containing noble metal nanoparticles is proposed. Ore-forming system features of Mykert-Sanzheevka field are considered.展开更多
The relevant results of thermodynamics simulation test, recrystallization study and FEM numercal simulation are described. A method is also introduced that the controlled hot forming is carried out by adopting the pro...The relevant results of thermodynamics simulation test, recrystallization study and FEM numercal simulation are described. A method is also introduced that the controlled hot forming is carried out by adopting the program of expansion-extrusion compound forming.展开更多
The forming condition of coal and coaly organic matter is analyzed. The dynamics of hydrocarbon generation of coal and coaly organic matter is discussed. It has been pointed out that the temperature is the main predom...The forming condition of coal and coaly organic matter is analyzed. The dynamics of hydrocarbon generation of coal and coaly organic matter is discussed. It has been pointed out that the temperature is the main predominant factor for the hydrocarbon generation of coal; chemical effect of structural pressing and shearing force accelerates the evolution of hydrocarbon derived from coal, and is the prerequisite for the hydrocarbons to be expelled from coal. The existence of atoms of N, S, O etc. is the prerequisite for forming the hydrocarbons at early evolution stage. The importance of NSO compounds in the evolution of hydrocarbon generation has been emphasized.展开更多
文摘The transient liquid phase diffusion bonding of Si 3N 4 ceramics with Ti/Ni/Ti and Al/Ti/Al multiple interlayers was performed. The formation of intermetallic compounds in situ and their effects on the joints strengths were investigated. The Ti/Ni/Ti interlayers produce NiTi and Ni 3Ti layers with considerable room temperature ductility and high elevated temperature strength to strengthen the bonding zone metals and the joints. The joints with 142 MPa shear strength at room temperature and 88 MPa shear strength at 800 ℃ are achieved under appropriate parameters, respectively. Al/Ti/Al interlayers transform into a special bonding zone metal with a large amount of Al 3Ti particles and a small amount of Al based solid solution, and in this case, the joints are strengthened significantly. Their strengths at room temperature and 600 ℃ reach 90 MPa and 30 MPa, respectively.
基金supported by Key Program of National Natural Science Foundation of China(Grant No.51135007)National Natural Science Foundation of China(Grant No.51075290)
文摘Bearing ring is the crucial component of bearing. With regard to such problems as material waste, low efficiency and high energy consumption in current process of producing large bearing ring, a new process named ＂casting-rolling compound forming technology＂ is researched by taking the typical 42CrMo slew bearing as object. Through theoretical analysis, the design criteria of the main casting-rolling forming parameters are put forward at first. Then the constitutive relationship model of as-cast 42CrMo steel and its mathematical model of dynamic recrystallization are obtained according to the results of the hot compression experiment. By a coupled thermal-mechanical finite element model for radial-axial rolling of bearing ring, the fraction of dynamic recrystallization is calculated and recrystallized grains size are predicated. Meanwhile, the effects of the initial rolling temperature and feed rate of idle roll on material microstructure evolution are analyzed. Finally, the industrial rolling experiment is designed and performed, based on the simulation results. In addition, mechanical and metallographic tests are conducted on rolled bearing ring to get the mechanical parameters and metallographic structure. The experimental data and results show that the mechanical properties of bearing ring produced by casting-rolling compound forming technology are up to industrial standard, and a qualified bearing ring can be successfully formed by employing this new technology. Through the study, a process of forming large bearing ring directly by using casting ring blank is obtained, which could provide an effective theoretical guidance for manufacturing large ring parts. It also has an edge in saving material, lowering energy and improving efficiency.
文摘This study examined the release characteristics of different N forms in an uncoated slow/controlled-release compound fertilizer （UCRF） and the N uptake and N-use efficiency by rice plants. Water dissolution, soil leaching, and pot experiments were employed. The dynamics of N release from the UCRF could be quantitatively described by three equations： the first-order kinetics equation [N1=N0 （1-e^-kt）], Elovich equation （N1=a ＋ blnt）, and parabola equation （N1=a ＋ bt^0.5）, with the best fitting by the first-order kinetics equation for different N （r= 0.9569^＊＊-0.9999^＊＊）. The release potentials （No values estimated by the first-order kinetics equation） of different N in the UCRF decreased in the order of total N 〉 DON 〉 urea-N 〉 NH4^＋-N 〉 NO3^-N in water, and total N 〉 NH4^＋-N 〉 DON 〉 urea-N 〉 NO3^--N in soil, respectively, being in accordance with cumulative amounts of N release. The constants of N release rate （k values and b values） for different N forms were in decreasing order of total N 〉 DON 〉 NH4^＋-N 〉 NO3^--N in water, whereas the k values were urea- N 〉DON 〉 NH4^＋-N 〉 total N 〉 NO3^--N, and the b values were total N 〉 NH4^＋-N 〉 DON 〉 NO3^--N 〉 urea-N in soil. Compared with a common compound fertilizer, the N-use efficiency, N-agronomy efficiency, and N-physiological efficiency of the UCRF were increased by 11.4%, 8.32 kg kg^-1, and 5.17 kg kg^-1, respectively. The ratios of different N to total N in the UCRF showed significant correlation with N uptake by rice plants. The findings showed that the first-order kinetics equation [Nt=N0 （l-e^kt）] could be used to describe the release characteristics of different N forms in the fertilizer. The UCRF containing different N forms was more effective in facilitating N uptake by rice compared with the common compound fertilizer containing single urea-N form.
文摘The new results of geologic-structural, petrographic and mineralogic-geochemical researches of Mykert-Sanzheevka ore field—the Uda-Vitim mineragenic zone South-West ending of West Transbaikalia are given. Its main ore-controlling structure, represented by losange, consisting of rhombohedral and tetrahedral blocks-duplexes mosaic clusters, which are separated by narrow tectonic sutures, is specified. It is clarified that polycomponent ores clusters are confined with these small-block sutures, made by subvolcanic dykes of shoshonite-latite volcano-plutonic association (233 - 188 million years), apodyke dynamometamorphites (breccias, cataclasite, mylonites) and also mechanometasomatites. Four stages of the dynamometamorphites formation characterized by different species compositions of ore minerals appeared as a result of mechanochemical reactions are determined. A carbonyl model of mineral microaggregates formation with films containing noble metal nanoparticles is proposed. Ore-forming system features of Mykert-Sanzheevka field are considered.
文摘The relevant results of thermodynamics simulation test, recrystallization study and FEM numercal simulation are described. A method is also introduced that the controlled hot forming is carried out by adopting the program of expansion-extrusion compound forming.
文摘The forming condition of coal and coaly organic matter is analyzed. The dynamics of hydrocarbon generation of coal and coaly organic matter is discussed. It has been pointed out that the temperature is the main predominant factor for the hydrocarbon generation of coal; chemical effect of structural pressing and shearing force accelerates the evolution of hydrocarbon derived from coal, and is the prerequisite for the hydrocarbons to be expelled from coal. The existence of atoms of N, S, O etc. is the prerequisite for forming the hydrocarbons at early evolution stage. The importance of NSO compounds in the evolution of hydrocarbon generation has been emphasized.
