A large amount of cutting heat is produced during the heavy cutting process,and insert life is restricted by the effect of thermal load.The thermal load experiment of cemented carbide SCS,WF and YT15 is carried out,an...A large amount of cutting heat is produced during the heavy cutting process,and insert life is restricted by the effect of thermal load.The thermal load experiment of cemented carbide SCS,WF and YT15 is carried out,and the results show that the bending strength and fracture toughness of cemented carbide material decrease obviously under cyclic thermal load,while in the cooling process,the material mechanical property changes worse suddenly.The high-temperature mechanical property of SCS is the most stable,and that of YT15 is the worst.Further,a relation model among cutting temperature,cutting parameters and insert life is established.Finally,the measures to improve heavy cemented carbide inserts life are summarized from the aspects of cutting parameters selection,insert optimization design and TiCN,Al2O3,TiN complex insert coating.The research results are expected to provide support and reference for heavy cutting technology and insert technology.展开更多
This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperatu...This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperature and loading frequency conditions. Dynamic modulus and phase angles obtained from the complex modulus tests were used in the construction of the Huet-Sayegh model. The dynamic modulus master curve was developed by the Huet-Sayegh model as well as the Burgers model for comparison purpose. The results showed that EAC exhibits typical rheological behavior whose dynamic modulus decreases with the increase of temperature while increases with the increase of frequency,and phase angles increase with the decrease of frequencies and the increase of temperatures. The Huet-Sayegh model predicts the dynamic modulus master curve of EAC very well and much better than the Burgers model over a wide range of frequencies.展开更多
Much attention has been paid to white LEDs because of their potential applications in the illumination.The doping of rare earth ions plays an important role in the optical properties of yellow fluorescent powder.And m...Much attention has been paid to white LEDs because of their potential applications in the illumination.The doping of rare earth ions plays an important role in the optical properties of yellow fluorescent powder.And mainly aiming to raise the intensity and the luminous rate of the white LEDs and by photoluminescence and electroluminescence,the luminescence spectrum of yellow fluorescent powder bought from different places is measured.Furthermore, the luminous intensity in the normal direction and the angle distribution of half maximum power for the white LEDs packed with cylindrical Φ 5 epoxy on the same blue GaN chips are also measured under the same manufacture conditions. The results show that the yellow fluorescent powder bought from China mainland has higher optical output rate than that bought from China Taiwan and hence is more suitable to fabricate the white LEDs for practical use.展开更多
基金Sponsored by the National Natural Science Foundation of China(Grant No.51205095)Support Program for Key Youth(Grant No.1154G39)
文摘A large amount of cutting heat is produced during the heavy cutting process,and insert life is restricted by the effect of thermal load.The thermal load experiment of cemented carbide SCS,WF and YT15 is carried out,and the results show that the bending strength and fracture toughness of cemented carbide material decrease obviously under cyclic thermal load,while in the cooling process,the material mechanical property changes worse suddenly.The high-temperature mechanical property of SCS is the most stable,and that of YT15 is the worst.Further,a relation model among cutting temperature,cutting parameters and insert life is established.Finally,the measures to improve heavy cemented carbide inserts life are summarized from the aspects of cutting parameters selection,insert optimization design and TiCN,Al2O3,TiN complex insert coating.The research results are expected to provide support and reference for heavy cutting technology and insert technology.
基金Sponsored by the Natgional Natural Science Foundation of China(Grant No.51208103)the China Postdoctoral Science Foundation(Grant No.2012M520976)the Basic Research Foundation of Southeast University
文摘This paper presents an investigation into modelling the rheological properties of epoxy asphalt concrete( EAC) by using the Huet-Sayegh model. Complex modulus tests were conducted on EAC specimens at various temperature and loading frequency conditions. Dynamic modulus and phase angles obtained from the complex modulus tests were used in the construction of the Huet-Sayegh model. The dynamic modulus master curve was developed by the Huet-Sayegh model as well as the Burgers model for comparison purpose. The results showed that EAC exhibits typical rheological behavior whose dynamic modulus decreases with the increase of temperature while increases with the increase of frequency,and phase angles increase with the decrease of frequencies and the increase of temperatures. The Huet-Sayegh model predicts the dynamic modulus master curve of EAC very well and much better than the Burgers model over a wide range of frequencies.
文摘Much attention has been paid to white LEDs because of their potential applications in the illumination.The doping of rare earth ions plays an important role in the optical properties of yellow fluorescent powder.And mainly aiming to raise the intensity and the luminous rate of the white LEDs and by photoluminescence and electroluminescence,the luminescence spectrum of yellow fluorescent powder bought from different places is measured.Furthermore, the luminous intensity in the normal direction and the angle distribution of half maximum power for the white LEDs packed with cylindrical Φ 5 epoxy on the same blue GaN chips are also measured under the same manufacture conditions. The results show that the yellow fluorescent powder bought from China mainland has higher optical output rate than that bought from China Taiwan and hence is more suitable to fabricate the white LEDs for practical use.
