“On-off”switch for H_(2)and O_(2)generation from HCOOH resp.H_(2)O_(2)

In spite of the numerous advances in the development of H_(2)and O_(2)evolutions upon water splitting,the separation of H_(2)from O_(2)still remains a severe challenge.Herein,the novel dual-functional nanocatalysts Pd/carbon nanosphere(CNS),obtained via immobilization of ultrafine Pd nanoparticles onto CNS,are developed and employed for both selective H_(2)generation from HCOOH dehydrogenation and O_(2)evolution from H_(2)O_(2)decomposition.In these reactions,the highest activities for Pd/CNS-800(i.e.,calcinated at 800℃)are 2478 h−1 and 993 min^(−1)for H_(2)and O_(2)evolution,respectively.The highly efficient and selective“on-off”switch for selective H_(2)generation from HCOOH is successfully realized by pH adjustment.This novel and highly efficient nanocatalyst Pd/CNS-800 not only provides new approaches for the promising application of HCOOH and H_(2)O_(2)as economic and safe H_(2)and O_(2)carriers,respectively,for fuel cells,but also promotes the development of“on-off”switch for on-demand H_(2)evolution.

A super junction SiGe low-loss fast switching power diode

This paper proposes a novel super junction （S J） SiGe switching power diode which has a columnar structure of alternating p- and n- doped pillar substituting conventional n- base region and has far thinner strained SiGe p＋ layer to overcome the drawbacks of existing Si switching power diode. The SJ SiGe diode can achieve low specific on-resistance, high breakdown voltages and fast switching speed. The results indicate that the forward voltage drop of SJ SiGe diode is much lower than that of conventional Si power diode when the operating current densities do not exceed 1000 A/cm^2, which is very good for getting lower operating loss. The forward voltage drop of the Si diode is 0.66V whereas that of the SJ SiGe diode is only 0.52V voltages are 203 V for the former and 235 V for the latter. at operating current density of 10A/cm^2. The breakdown Compared with the conventional Si power diode, the reverse recovery time of SJ SiGe diode with 20 per cent Ge content is shortened by above a half and the peak reverse current is reduced by over 15%. The SJ SiGe diode can remarkably improve the characteristics of power diode by combining the merits of both SJ structure and SiGe material.

Global Synchronization of Directed Networks with Fast Switching Topologies

Global synchronization of a class of directed dynamical networks with switching topologies is investigated.It is found that if there is a directed spanning tree in the fixed time-average of network topology and the time-averageis achieved sufficiently fast,then the network will reach global synchronization for sufficiently large coupling strength.

Study of the Fast-Closing Switch Used for Fault Current Limiters in Power System

This paper presents a new type of fault current limiter (FCL) based on fast closing switch, which is composed of a capacitor bank and a reactor in series. The main control component is a fast closing switch connected in parallel with the capacitors, which is driven by the electromagnetic repulsion force. It can response the order within 1 ms. When fault occurs, the switch closes and the capacitors are bypassed, and the fault current is limited by the reactor. Simulation analysis and experiment show that the electromagnetic repulsion force actuator can meet the demand of fast closing switch, it is feasible to develop the FCL with low cost and high reliability.

Vacuum Switching Technology for Future of Power Systems

Even though switching in vacuum is a technology with almost 100 years of history,its recent develop-ments are still changing the future of power transmission and distribution systems.First,current switch-ing in vacuum is an eco-friendly technology compared to switching in SF 6 gas,which is the strongest greenhouse gas according to the Kyoto Protocol.Vacuum,an eco-friendly natural medium,is promising for reducing the usage of SF 6 gas in current switching in transmission voltage.Second,switching in vacuum achieves faster current interruption than existing alternating current(AC)switching technolo-gies.A vacuum circuit breaker(VCB)that uses an electromagnetic repulsion actuator is able to achieve a theoretical limit of AC interruption,which can interrupt a short-circuit current in the first half-cycle of a fault current,compared to the more common three cycles for existing current switching technologies.This can thus greatly enhance the transient stability of power networks in the presence of short-circuit faults,especially for ultra-and extra-high-voltage power transmission lines.Third,based on fast vacuum switching technology,various brilliant applications emerge,which are benefiting the power systems.They include the applications in the fields of direct current(DC)circuit breakers(CBs),fault current lim-iting,power quality improvement,generator CBs,and so forth.Fast vacuum switching technology is promising for controlled switching technology in power systems because it has low variation in terms of opening and closing times.With this controlled switching,vacuum switching technology may change the“gene”of power systems,by which power switching transients will become smoother.

Influence of Series Choke on Damping of Switching Transients in Distribution Transformers

Distribution transformers operating in modern system grids or in industrial networks are subjected to many switching transients,which may occur due to routine operations,network reconfigurations or as reaction on protection signals.Depending on the network configuration and parameters,such events may lead to external overvoltages and result in additional stresses on the insulation system.This paper presents the influence of a series choke on damping of switching transients in distribution transformers.The impact of the choke is assessed by both amplitude and rise time reduction.The suppression of the transient rise time is shown for a test configuration involving distribution transformers connected to low loss cable lines and a medium voltage breaker.Such phenomena are especially typical for industrial networks where switching operations are very frequent.Both simulation and experiment results are given.Simulation results as well as measurement results confirmed that switching events can lead to high dU/dt and in consequence,can have adverse impacts on insulation system.Voltage escalation during switching event is strongly related with system conditions.The results obtained for presented mitigation method are promising and indicate significant dU/dt reduction as well as number of ignitions and voltage peak value.The protection of distribution transformers with a series choke is a new approach dedicated to environments prone to the occurrence of transients with high steepness.Experimental results show that the application of serial choke with suitable parameters realizes the reduction of dU/dt at the machines terminal from 24 kV/μs to 5 kV/μs,as well as the reduction of voltage peak value from 10 kV to 5 kV.The number of ignitions is also reduced.

Research on a Fast-Closing Switch Based Fault Current Limiter with Series Compensation

A new type of fault current limiter (FCL) with series compensation based fast-closing switch is proposed. It is composed of a capacitor bank and a reactor in series. The main control component is a fast-closing switch connected in parallel with the capacitors, which is driven by the electromagnetic repulsion force. When fault occurs, the switch closes and bypasses the capacitors, and the fault is limited by the reactor then. Simulated analysis and experiments show that it is feasible to develop the FCL with low cost and high reliability. The effectiveness of transient stability for power system is evaluated by digital simulation.

直流快速开断技术研究进展和展望

由于直流电流无自然过零点且短路电流上升率高,直流电流快速开断与系统故障切除成为制约直流电力系统发展的一大瓶颈。该综述首先介绍了直流快速开断技术要求与难点。其次,详细分析了直流快速开断过程涉及的关键技术,包括电流转移技术、固态式直流开断技术、介质恢复技术和高速机械开关技术等,综述了各种技术的当前发展现状及其应用情况,对比了不同技术方案的特点及适应性。最后,对直流快速开断技术未来发展方向进行了讨论和总结,为小型化、高性能、低成本、高可靠快速直流断路器的研发及推广应用提供了新的技术思路。

一种基于磁耦合转移原理的10kV直流断路器

直流电流没有自然过零点,因此开断直流短路电流比开断交流短路电流更为困难。本文介绍一种基于磁耦合电流转移原理的中压10kV直流断路器拓扑方案,该断路器可实现对15kA直流电流的快速开断。首先,对直流断路器原理和控制逻辑进行介绍;然后,根据拓扑方案提出快速机械开关、电力电子开关、磁耦合装置等核心部件的设计思路;最后,搭建仿真模型对该方案进行仿真分析,模拟不同工况下的开断情况,仿真结果验证了该方案的有效性。

基于阈值控制策略的Filippov Chay神经元动力学及其耦合同步

细胞内外带电离子的连续泵送和传递产生的电磁感应效应对神经元的电活动及模态转换会产生一定的影响,促使其展现出更加丰富的放电特性.文章基于电磁感应影响下的Chay神经元模型,引入了一种以膜电压为阈值的不连续控制策略,建立了相应的Filippov Chay神经元模型,探究了在阈值控制策略影响下的神经元放电节律转迁及相应的边界运动.首先,对系统的边界动力学及滑膜动力学进行了理论分析.其次,利用单双参数分岔图探究了系统多样的放电模式.再次,结合Matcont仿真及稳定性理论详细分析了系统的平衡点及其稳定性,并且利用快慢动力学分析法进一步研究了在阈值影响下所产生的滑膜动力学及各种边界运动的切换.最后,通过电突触耦合,对不同阈值条件下耦合神经元的同步问题进行了讨论.数值仿真结果表明,在阈值的调控下Filippov Chay系统会产生滑膜放电活动及相应的穿越运动和擦边运动,同时其放电周期数也会随着阈值呈现出不同的变化规律,且对于不同阈值下的电耦合情况而言,在系统实现完全同步后都会稳定在周期数较低的放电态.以上所得结果有助于更好地理解神经元滑膜的相关控制,对进一步探究生物神经系统中复杂放电活动和信息处理的动力学行为提供了一定的帮助.

支路开关自放电对大型多路并联FLTD脉冲源可靠性的影响

快脉冲直线型变压器驱动源(fast linear transformer driver,FLTD)是建设下一代大型Z箍缩装置最有前景的技术路线之一。大型FLTD脉冲源中数以万计气体开关的可靠运行是提高Z箍缩装置可靠性的重要因素。该文基于15 MAZ箍缩科学实验装置的FLTD脉冲源设计,采用Monte-Carlo方法建立考虑支路开关自放电及其载荷共享效应的FLTD脉冲源可靠性计算模型,分析开关故障模式及其触发策略对脉冲源可靠性的影响。结果表明,主支路开关自放电产生的故障电压会引起开关级联自放电,降低装置可靠性。若主支路开关工作系数设定在0.5~0.7范围内,FLTD脉冲源故障率可低于1×10^(-4)。此外,触发器及触发支路开关的高可靠性对于提升脉冲源可靠性至关重要,增加触发器脉冲数量、降低触发器自放电故障率能够有效提升脉冲源可靠性,当触发器脉冲数量提升至4倍后,FLTD脉冲源故障率有望降低至1×10^(-5)以下。研究结果为大型FLTD脉冲源的开关工作系数及触发策略的选取提供参考,具有重要的工程应用价值。

一种应用于探测的可预测电流模式FSBB电路

探测器的能源供给离不开DC-DC变换器,先进的控制方法能提高工作效率。预测电流模式控制相比于传统的PI控制具有动态响应快、易于进行过流保护等优点,因此被广泛应用到电力电子控制领域。由于控制回路的问题,不能通过计算开环增益的方式对负载波动与输出电压变化的闭环传递函数进行有效地设计。因此,提出了一种在不加前馈控制的情况下,基于预测电流模式控制四开关Buck-Boost(four-switch Buck-Boost,FSBB)变换器补偿器的设计方案,该方法能提升负载动态响应,通过实验数据,证明了该方法的有效性。

直线旋转开关磁阻电机的轴向速度控制与快速轴向定位

目前直线旋转开关磁阻电机(Linear-rotary switched reluctance motor,LRSRM)只可实现轴向定位控制,两自由度运动方式较为单一。为提高LRSRM轴向控制性能,本文提出了一种轴向速度控制方法,通过线性位置/速度观测器协调控制转子的轴向位移和轴向速度,由转矩与轴向力的数学模型解算出转矩及轴向力绕组的给定电流,再将其分配到对应的绕组导通区间,分别进行电流滞环控制。该方法可以有效调节转子在旋转过程中的轴向定位速度。仿真和实验验证了所提方法的控制效果。

基于虚拟电容的构网型MMC快速平滑切换策略

为减小构网型模块化多电平换流器黑启动完成后的并网瞬间冲击,提出一种综合考虑并网点电压的幅值、频率及相位的最优并网控制策略。通过实时检测并网两端的电压幅值、频率及相位,达到阈值后开始并网。同时,针对该策略同步时间过长的问题,提出一种基于虚拟电容的构网型模块化多电平换流器快速并网切换控制策略,在控制环节引入虚拟电容快速调节构网型模块化多电平换流器的电压相位,节省储能型模块化多电平换流器的备用容量。最后,通过搭建硬件在环测试平台验证最优并网控制和快速并网切换控制策略的有效性和正确性。

基于PCIE的多嵌入式人工智能处理器低延迟数据交换技术

针对多嵌入式人工智能(Artificial Intelligence,AI)处理器板卡之间的任务调度和数据交换冲突以及提高多板卡堆叠扩展时的可靠性和运行效率问题,文中提出了一种虫洞交换结构多嵌入式人工智能处理器高速数据交换技术和数据帧结构的解决方法。该方法基于PCIE(PCI Express)高速数据接口,将数据以数据单元的形式进行信息传递,并设计多重权重决策算法避免数据传输中的冲突,实现任务的并发多线程处理。搭建FPGA(Field Programmable Gate Array)平台进行设计和测试,结果表明PCIE的传输带宽利用效率达到了85%以上,数据交换延迟小于20μs,系统中断任务响应平均最大延迟时间为8.775μs。该技术适用于多处理器协同的高速交换电路,可扩展至混合PCIE和RapidIO交换电路结构。

基于脉冲变压器的快前沿固态触发器

结合理论求解、仿真分析与实验验证,确定了影响脉冲变压器型触发器输出前沿的主要因素,并研制了一台能可靠触发真空沿面闪络开关导通的快前沿固态触发器。研究结果表明:影响触发器输出脉冲前沿的关键因素为脉冲变压器漏感、匝数比和半导体开关开通速度;不同绕制方式的脉冲变压器漏感差异很大,最小漏感绕法的变压器漏感值低1个数量级;选用开通速度优于15 ns的碳化硅金属氧化物半导体场效应晶体管(SiC MOSFET)、绕制低漏感(小于0.5μH)的脉冲变压器,实现了前沿为20.4 ns(10%~90%)、幅值为16.5 kV的快前沿输出;控制SiC MOSFET的驱动脉宽在35~55 ns变化可以控制触发电流峰值在35~55 A范围内变化。

基于SD-WAN混合链路实现规模无关快速路由切换的设计

软件定义广域网(Software Defined Wide Area Network,SD-WAN)作为被应用于广域网连接的新型网络技术,使用混合链路为广域网流量提供多条Overlay转发路径,配合智能应用选路等技术为网络流量提供最优路径动态选择的能力。提出了一种基于混合链路多Overlay隧道实现网络规模解耦下快速路由切换的新型设计,在广域网链路中断后提供路由收敛时间确定性上界保证,给出关键的数据结构及工作流程,对相关工程实施具备较好的指导作用。

人骨骼肌TnI-fast基因克隆和体外表达

目的 构建人骨骼肌TnI fast基因分泌型真核表达载体 ,为利用TnI fast基因进行抗肿瘤血管生成基因治疗奠定基础。方法 采用PCR和RT PCR制备TnI fastcDNA ,构建TnI fast基因克隆质粒 ,测序证实后将TnI fastcDNA插入到pSecTag2B构建分泌型重组真核表达质粒。然后用TnI fast基因重组表达质粒转染COS 1细胞 ,检测TnI fast基因体外表达。结果 DNA测序证实 ,我们从人骨骼肌总RNA和cDNA文库中扩增的TnI fastcDNA序列与NCBIGenebankTnI fastcDNA序列完全一致。ELISA检测证实 ,TnI fast pSecTag2B转染后目的基因可在真核细胞中分泌表达。结论 本研究成功地构建了TnI fast基因重组表达质粒 。

110 kV双断口快速开关效率优化分析

电磁斥力效率的优化研究,以往研究主要针对斥力盘、线圈等关键零件的结构优化和参数匹配,以及预充电电容的电压和容值的优化分析,很少有关于开关辅助支撑结构件对效率影响的分析研究。不同结构形式和材质的辅助支撑结构件对斥力盘效率有着不可忽视的影响。文中以快速开关支撑板作为分析研究对象,在不改变样机结构形式的前提下,提出了通过设计导磁板,对支撑板开槽等方式,降低支撑板的涡流损耗,提高电磁斥力效率。文章最后,基于仿真结果,对一款110 kV双断口快速开关样机进行了改造设计。试验结果表明,在容值不变情况下,增加导磁板或者支撑板开槽可以有效降低电容预充电压,提高斥力机构效率。

快速真空开关合闸触头弹跳暂态过程研究

以电磁斥力驱动器作为操动机构的快速真空开关具有分闸速度快,分合闸时间短和分合闸时间分散性小的优势,目前已广泛应用于多种电力设备中。目前对于快速真空开关的分闸过程已有众多研究,但合闸过程的相关问题尚属空白。文中研究了快速真空开关合闸过程中触头弹跳问题。建立了多物理场耦合仿真模型,完整描述了快速真空开关的合闸过程。得到了快速真空开关的v1与Dmax的关系,其中v1为合闸过程中动静触头首次接触的瞬时速度,Dmax为动触头的最大弹跳距离。根据这一关系式,确定了合闸过程中无触头弹跳情况下的临界瞬时合闸速度vcri。根据vcri限制,设计了一种新型的油阻尼器来调节快速真空开关的合闸行程曲线,实现无触头弹跳合闸。研制了装备新型油缓冲器的快速真空开关,搭建了机械特性测试平台,对其合闸特性进行了测试。测试结果表明:测量结果与仿真结果之间的误差不超过10%,且实现了无触头弹跳合闸。