The critical slip distance in rate and state model for fault friction in the study of potential earthquakes can vary wildly from micrometers to few me-ters depending on the length scale of the critically stressed faul...The critical slip distance in rate and state model for fault friction in the study of potential earthquakes can vary wildly from micrometers to few me-ters depending on the length scale of the critically stressed fault.This makes it incredibly important to construct an inversion framework that provides good estimates of the critical slip distance purely based on the observed ac-celeration at the seismogram.To eventually construct a framework that takes noisy seismogram acceleration data as input and spits out robust estimates of critical slip distance as the output,we first present the performance of the framework for synthetic data.The framework is based on Bayesian inference and Markov chain Monte Carlo methods.The synthetic data is generated by adding noise to the acceleration output of spring-slider-damper idealization of the rate and state model as the forward model.展开更多
The hazards of fault reactivation caused by fluid injection are a growing concern.However,traditional evaluation methods of fault stability are likely to underestimate the risk in fault segments with a high clay conte...The hazards of fault reactivation caused by fluid injection are a growing concern.However,traditional evaluation methods of fault stability are likely to underestimate the risk in fault segments with a high clay content.Therefore,an extended evaluation method of fault stability(ECPP)incorporating the heterogeneity in friction strength caused by variation in the clay content within the fault zone is established in this study.After characterizing the current stress field of the BZ34-2 Oilfield in the Huanghekou Sag,Bohai Bay Basin,the reactivation potential of faults is evaluated using both traditional and ECPP methods.Traditional evaluation of fault stability shows that all faults are stable in the present stress field.Faults oriented ENE have a relatively high risk.The maximum sustainable fluid pressure Δp is approximately 8.8-8.9 MPa and 9.3-9.9 MPa.When considering the heterogeneity in fault friction strength,the fault stability is clearly controlled by the clay content of the faults.The high-risk fault segments assessed using traditional methods are no longer obvious,which reflects the importance of incorporating friction strength heterogeneity in the process of fault evaluation.Moreover,the results also show that most fault segments are activated when the fault zone is dominated by montmorillonite,reflecting the strong influence of clay mineral types on fault stability.The factors influencing the heterogeneity of fault friction strength are very complicated in actual situations.Therefore,future work should focus on establishing a database through a large number of experiments and investigating the relationship between the friction coefficient and the main controlling factors.展开更多
High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 We...High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake. The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties. Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa, using a rotary-shear high-velocity frictional testing machine. The gouge displays slip weakening behavior as initial peak friction decays towards steady-state values after a given displacement. Both peak friction and steady-state friction remain high at slow slip rates are exam- ined and gouge only exhibits dramatic weakening at high slip rates, with steady-state friction coefficient values of about 0.1 to 0.2. Specific fracture energy ranges from 1 to 4 MN/m in our results and this is of the same order as seismically determined values. Low friction coefficients measured on experimental faults are in broad agree- ment with lack of thermal anomaly observed from temperature measurements in WFSD-1 drill hole (Wenchuan Earthquake Fault Scientific Drilling Project), which can be explained by even smaller friction coefficient for the Wenchuan earthquake fault. High-velocity friction experiments with pore water needs to be done to see if even smaller friction is attained or not. Shiny slickenside surfaces form at high slip rates, but not at slow slip rates. Slip zone with slickenside surface changes its color to dark brown and forms duplex-like microstructures, which are similar to those microstructures found in the fault gouges from the Hongkou outcrop. Detailed comparisons between experimentally deformed gouge samples and WFSD drill cores in the future will reveal how much we could reproduce the dynamic weakening processes in operation in fault zones during Wenchuan earthquake at present.展开更多
This paper reports internal structures of a bedding-parallel fault in Permian limestone at Xiaoji-aqiao outcrop that was moved by about 0.5 m during the 2008 MW7.9 Wenchuan earthquake. The fault is located about 3 km ...This paper reports internal structures of a bedding-parallel fault in Permian limestone at Xiaoji-aqiao outcrop that was moved by about 0.5 m during the 2008 MW7.9 Wenchuan earthquake. The fault is located about 3 km to the south from the middle part of Yingxiu-Beichuan fault, a major fault in the Longmenshan fault system that was moved during the earthquake. The outcrop is also located at Anxian transfer zone between the northern and central segments of Yingxiu-Beichuan fault where fault system is complex. Thus the fault is an example of subsidiary faults activated by Wenchuan earthquake. The fault has a strike of 243°or N63°E and a dip of 38°NW and is nearly optimally oriented for thrust motion, in contrast to high-angle coseismic faults at most places. Surface outcrop and two shallow drilling studies reveal that the fault zone is several centimeters wide at most and that the coseismic slip zone during Wenchuan earthquake is about 1 mm thick. Fault zone contains foliated cataclasite, fault breccia, black gouge and yellowish gouge. Many clasts of foliated cataclasite and black gouge contained in fault breccia indicate multiple slip events along this fault. But fossils on both sides of fault do not indicate clear age difference and overall displacement along this fault should not be large. We also report results from high-velocity friction experiments conducted on yellowish gouge from the fault zone using a rotary shear low to high-velocity frictional testing apparatus. Dry experiments at normal stresses of 0.4 to 1.8 MPa and at slip rates of 0.08 to 1.35 m/s reveal dramatic slip weakening from the peak friction coeffcient of around 0.6 to very low steady-state friction coeffcient of 0.1–0.2. Slip weakening parameters of this carbonate fault zone are similar to those of clayey fault gouge from Yingxiu-Beichuan fault at Hongkou outcrop and from Pingxi fault zone. Our experimental result will provide a condition for triggering movement of subsidiary faults or off-fault damage during a large earthquake.展开更多
This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2...This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake.Vertical offset and horizontal displacement at the trench site were 2.8 m(NW side up)and 4.8 m(right-lateral),respectively.The fault zone formed in Triassic sandstone,siltstone,and shale about 500 m away from the Yingxiu-Beichuan fault,a major fault in the Longmenshan fault system.A trench survey across the coseismic fault,and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about0.5 and 250-300 m in widths,respectively,and that the fault strikes N62°E and dips 68° to NW.Quaternary conglomerates were recovered beneath the fault in the drilling,so that the fault moved at least 55 m along the coseismic slip zone,experiencing about 18 events of similar sizes.The fault core is composed of grayish gouge(GG) and blackish gouge(BG) with very complex slip-zone structures.BG contains low-crystalline graphite of about 30 %.High-velocity friction experiments were conducted at normal stresses of 0.6-2.1 MPa and slip rates of 0.1-2.1 m/s.Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient lpto steadystate friction coefficient lssover a slip-weakening distance Dc.Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces,respectively.Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake.展开更多
This paper experimentally explores the frictional sliding behavior of two simulated gouges:one,a series of quartz–smectite mixtures,and the other,powdered natural rocks,aiming to evaluate and codify the effect of min...This paper experimentally explores the frictional sliding behavior of two simulated gouges:one,a series of quartz–smectite mixtures,and the other,powdered natural rocks,aiming to evaluate and codify the effect of mineralogy on gouge dilation and frictional strength,stability,and healing.Specifically,velocity-stepping and slide-hold-slide experiments were performed in a double direct shear configuration to analyze frictional constitutive parameters at room temperature,under normal stresses of 10,20,and 40 MPa.Gouge dilation was measured based on the applied step-wise changes in shear velocity.The frictional response of the quartz–smectite mixtures and powdered natural rocks are affected by their phyllosilicate content.Frictional strength and healing rates decrease with increasing phyllosilicate content,and at 20 wt.%a transition from velocity-weakening to velocity-strengthening behavior was noted.For both suites of gouges,dilation is positively correlated with frictional strength and healing rates,and negatively correlated with frictional stability.Changes in the permeability of gouge-filled faults were estimated from changes in mean porosity,indexed through measured magnitudes of gouge dilation.This combined analysis implies that the reactivation of caprock faults filled with phyllosilicaterich gouges may have a strong influence on permeability evolution in caprock faults.展开更多
This paper focuses on the investigation of a hybrid seismic isolation system with passive variable friction dampers for protection of structures against near fault earthquakes. The seismic isolation can be implemented...This paper focuses on the investigation of a hybrid seismic isolation system with passive variable friction dampers for protection of structures against near fault earthquakes. The seismic isolation can be implemented by replacing the conventional columns fixed to the foundations by seismic isolating ones. These columns allow horizontal displacement between the superstructure and the foundations and decouple the building from the damaging earthquake motion. As a result, the forces in the structural elements decrease and damage that may be caused to the building by the earthquake significantly decreases. However, this positive effect is achieved on account of displacements occurring in the isolating columns. These displacements become very large when the structure is subjected to a strong earthquake. In this case, impact may occur between the parts of the isolating column yielding their damage or collapse. In order to limit the displacements in the isolating columns, it is proposed to add variable friction dampers. A method for selecting the dampers' properties is proposed. It is carried out using an artificial ground motion record and optimal active control algorithm. Numerical simulation of a sevenstory structure shows that the proposed method allows efficient reduction in structural response and limits the displacements at the seismic isolating columns.展开更多
Little attention had been paid to the intracontinental strike-slip faults of the Tibetan Plateau. Since the discovery of the Longriba fault using re-measured GPS data in 2003, an increasing amount of attention has bee...Little attention had been paid to the intracontinental strike-slip faults of the Tibetan Plateau. Since the discovery of the Longriba fault using re-measured GPS data in 2003, an increasing amount of attention has been paid to this neglected fault. The local relief and transverse swath profile show that the Longriba fault is the boundary line that separates the high and flat tomography of the Tibet plateau from the high and precipitous tomography of Orogen. In addition, GPS data shows that the Longriba fault is the boundary line where the migratory direction of the Bayan Har block changed from eastward to southeastward. The GPS data shows that the Longriba fault is the boundary fault of the sub-blocks of the eastern Bayan Har block. We built three-dimensional models containing the Longriba fault and the middle segment of the Longmenshan fault, across the Bayan Har block and the Sichuan Basin. A nonlinear finite element method was used to simulate the fault behavior and the block deformation of the Eastern Tibetan Plateau. The results show that the low resistivity and low velocity layer acts as a detachment layer, which causes the overlying blocks to move southeastward. The detachment layer also controls the vertical and horizontal deformation of the rigid Bayan Har block and leads to accumulation strain on the edge of the layer where the Longmenshan thrust is located. After a sufficient amount of strain has been accumulated on the Longmenshan fault, a large earthquake occurs, such as the 2008 Wenchuan earthquake. The strike slip activity of the Longriba fault, which is above the low resistivity and low velocity layer, partitions the lateral displacements of the Bayan Har block and adjusts the direction of motion of the Bayan Har block, from the eastward moving Ahba sub-block in the west to southeastward moving Longmenshan sub-block in the east. Four models with different depths to the Longriba fault were constructed: (1) a shallow fault with a depth of only 4 km, (2) a deeper fault that is half as deep as the Longmenshan fault, (3) a deep fault that is 2 km shallower than the low resistivity and low velocity layer, and (4) a fault that is as deep as the low resistivity and low velocity layer. The activity and influence of the Longriba fault with different development stage under this tectonic system were shown: in one Earthquake recurrence period, the rupture region of the fault increases with the depth of the fault, and the lateral slip partition by the fault also changes with the fault depth. It suggests that the Longriba fault is a newly generated fault that developed after the quick uplift in Late Cenozoic along this tectonic setting and gradually extended from the northwest to southeast. The calculations provide the characteristic of block deformation and fault behaviors of intra-continental strike-slip fault and major boundary thrust faults in the eastern margin of the Tibet plateau. Although the low resistivity and low velocity layer controls the deformation of the Bayan Hat block and the uplift of the Longmenshan thrust, the partition of the Longriba fault has an important influence on the intra-plate deformation and modern geomorphic evolution.展开更多
We monitored the amplitude changes of coda transmission waves around 500 kHz across the frictional interface of a simulated 1. 5-meter-long fault during normal stress holding test.We find that the amplitude of coda tr...We monitored the amplitude changes of coda transmission waves around 500 kHz across the frictional interface of a simulated 1. 5-meter-long fault during normal stress holding test.We find that the amplitude of coda transmission waves increases with the logarithm of stationary contact time. Localized increase amounted to a level ranging from 4% to 16%along the fault is observed during the 1-hour experiment. We discuss that the frictional strength at mesoscopic scale,which is related to the amplitude of coda transmission waves,is responsible for the phenomenon. Combining the reported method with other complementary approaches will enhance the understanding of fault mechanism either at laboratory or on-site applications.展开更多
To understand precursory phenomena before seismic fault sliP,this work focuses onearthquake nucleation process on a fault plane through numerical simulation.Rate and statedependent friction law with variable normal st...To understand precursory phenomena before seismic fault sliP,this work focuses onearthquake nucleation process on a fault plane through numerical simulation.Rate and statedependent friction law with variable normal stress is employed in the analysis.The resultsshow that in the late stage of nucleation process:(1)The maximum slip velocity ismonotonically accelerating;(2)The slipping hot spot(where the slip rate is maximum)migrates spontaneously from a certain instant,and such migration is spatially continuous;(3)When the maximum velocity reaches a detectable order of magnitude(at least one orderof magnitude greater than the loading rate),the remaining time is 20 hours or longer,andthe temporal variation of slip velocity beyond this point may be used as a precursoryindicator;(4)The average slip velocity is related to the remaining time by a log-log linearrelation,which means that a similar relation between rate of microseismicity and remainingtime may also exist;(5)when normal stress variation is taken展开更多
The present-day stress state of the Yingxiu-Beichuan fault after the Wenchuan earthquake was re-estimated using measured in-situ stress data obtained after the Wenchuan earthquake. The results reveal that the gradient...The present-day stress state of the Yingxiu-Beichuan fault after the Wenchuan earthquake was re-estimated using measured in-situ stress data obtained after the Wenchuan earthquake. The results reveal that the gradient coefficients of principal stresses versus depth decrease from south to north along the Yingxiu-Beichuan fault, revealing that the stress level decreases from south to north. The consistency between the present-day stress levels and surface ruptures generated during the earthquake indicates that the accumulated tectonic stress beneath the Yingxiu-Beichuan fault before the Wenchuan earthquake was relieved in form of surface ruptures. This resulted in the stress remaining high in the southern section of the Yingxiu-Beichuan fault but relatively low in the northern section. Abnormal high pore pressure conditions and an extremely low frictional coefficient play important role in the interpretation of the stress field adjustment and seismic events observed after the Wenchuan earthquake along this fault, according to the estimation results using the Coulomb frictional-failure theory incorporating frictional coefficients ranging from 0.4 to 1.0. To accurately estimate the seismological hazard of the Yingxiu-Beichuan fault by analyzing fault instability using the Coulomb frictional-failure theory, much attention should be focused on the pore pressure conditions and the evolution state of the frictional coefficient under the present-day stress state.展开更多
This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results ...This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results from velocity-jump tests on Pingxi fault gouge to illustrate technical problems in conducting velocity-stepping tests at high velocities.The apparatus is capable of producing plate to seismic velocities(44 mm/a to 2.1 m/s for specimens of 40 mm in diameter),using a 22 kW servomotor with a gear/belt system having three velocity ranges.A speed range can be changed by 103 or 106by using five electromagnetic clutches without stopping the motor.Two cam clutches allow fivefold velocity steps,and the motor speed can be increased from zero to 1,500 rpm in 0.1-0.2 s by changing the controlling voltage.A unique feature of the apparatus is a large specimen chamber where different specimen assemblies can be installed easily.In addition to a standard specimen assembly for friction experiments,two pressure vessels were made for pore pressures to 70 MPa;one at room temperature and the other at temperatures to 500 °C.Velocity step tests are needed to see if the framework of rate-and-state friction is applicable or not at high velocities.We report results from velocity jump tests from 1.4 mm/s to 1.4 m/s on yellowish gouge from a Pingxi fault zone,located at the northeastern part of the Longmenshan fault system that caused the 2008 Wenchuan earthquake.An instantaneous increase in friction followed by dramatic slip weakening was observed for the yellowish gouge with smooth sliding surfaces of host rock,but no instantaneous response was recognized for the same gouge with roughened sliding surfaces.Instantaneous and transient frictional properties upon velocity steps cannot be separated easily at high velocities,and technical improvements for velocity step tests are suggested.展开更多
文摘The critical slip distance in rate and state model for fault friction in the study of potential earthquakes can vary wildly from micrometers to few me-ters depending on the length scale of the critically stressed fault.This makes it incredibly important to construct an inversion framework that provides good estimates of the critical slip distance purely based on the observed ac-celeration at the seismogram.To eventually construct a framework that takes noisy seismogram acceleration data as input and spits out robust estimates of critical slip distance as the output,we first present the performance of the framework for synthetic data.The framework is based on Bayesian inference and Markov chain Monte Carlo methods.The synthetic data is generated by adding noise to the acceleration output of spring-slider-damper idealization of the rate and state model as the forward model.
基金the financial support from the National Natural Science Foundation of China(Grant Nos.42002152 and U20A2093)National Key Research and Development Program of China(Grant No.2022YFE0206800).
文摘The hazards of fault reactivation caused by fluid injection are a growing concern.However,traditional evaluation methods of fault stability are likely to underestimate the risk in fault segments with a high clay content.Therefore,an extended evaluation method of fault stability(ECPP)incorporating the heterogeneity in friction strength caused by variation in the clay content within the fault zone is established in this study.After characterizing the current stress field of the BZ34-2 Oilfield in the Huanghekou Sag,Bohai Bay Basin,the reactivation potential of faults is evaluated using both traditional and ECPP methods.Traditional evaluation of fault stability shows that all faults are stable in the present stress field.Faults oriented ENE have a relatively high risk.The maximum sustainable fluid pressure Δp is approximately 8.8-8.9 MPa and 9.3-9.9 MPa.When considering the heterogeneity in fault friction strength,the fault stability is clearly controlled by the clay content of the faults.The high-risk fault segments assessed using traditional methods are no longer obvious,which reflects the importance of incorporating friction strength heterogeneity in the process of fault evaluation.Moreover,the results also show that most fault segments are activated when the fault zone is dominated by montmorillonite,reflecting the strong influence of clay mineral types on fault stability.The factors influencing the heterogeneity of fault friction strength are very complicated in actual situations.Therefore,future work should focus on establishing a database through a large number of experiments and investigating the relationship between the friction coefficient and the main controlling factors.
基金supported by State Key Laboratory of Earthquake Dynamics (project No.LED2008A03)Wenchuan Earthquake Fault Scientific Drilling Project(WFSD),by a Grant-in-Aid for JSPS fellows to the first author (T.Togo) and a Grant-in-Aid for young scientists(B) 201007605,and by a 2009 FGI Grant-in-Aid of Fukada Geological Institute
文摘High-velocity friction experiments were conducted on clayey fault gouge collected from Hongkou outcrop of Beichuan fault, located at the southwestern part of Longmenshan fault system that caused the disastrous 2008 Wenchuan earthquake. The ultimate purpose of this study is to reproduce this earthquake by modeling based on measured frictional properties. Dry gouge of about 1 mm in thickness was deformed dry at slip rates of 0.01 to 1.3 m/s and at normal stresses of 0.61 to 3.04 MPa, using a rotary-shear high-velocity frictional testing machine. The gouge displays slip weakening behavior as initial peak friction decays towards steady-state values after a given displacement. Both peak friction and steady-state friction remain high at slow slip rates are exam- ined and gouge only exhibits dramatic weakening at high slip rates, with steady-state friction coefficient values of about 0.1 to 0.2. Specific fracture energy ranges from 1 to 4 MN/m in our results and this is of the same order as seismically determined values. Low friction coefficients measured on experimental faults are in broad agree- ment with lack of thermal anomaly observed from temperature measurements in WFSD-1 drill hole (Wenchuan Earthquake Fault Scientific Drilling Project), which can be explained by even smaller friction coefficient for the Wenchuan earthquake fault. High-velocity friction experiments with pore water needs to be done to see if even smaller friction is attained or not. Shiny slickenside surfaces form at high slip rates, but not at slow slip rates. Slip zone with slickenside surface changes its color to dark brown and forms duplex-like microstructures, which are similar to those microstructures found in the fault gouges from the Hongkou outcrop. Detailed comparisons between experimentally deformed gouge samples and WFSD drill cores in the future will reveal how much we could reproduce the dynamic weakening processes in operation in fault zones during Wenchuan earthquake at present.
基金supported by State Key Laboratory of Earthquake Dynamics (projectNo. LED2010A05, LED2010A03)Wenchuan Earthquake Fault Scientific Drilling Project (WFSD)
文摘This paper reports internal structures of a bedding-parallel fault in Permian limestone at Xiaoji-aqiao outcrop that was moved by about 0.5 m during the 2008 MW7.9 Wenchuan earthquake. The fault is located about 3 km to the south from the middle part of Yingxiu-Beichuan fault, a major fault in the Longmenshan fault system that was moved during the earthquake. The outcrop is also located at Anxian transfer zone between the northern and central segments of Yingxiu-Beichuan fault where fault system is complex. Thus the fault is an example of subsidiary faults activated by Wenchuan earthquake. The fault has a strike of 243°or N63°E and a dip of 38°NW and is nearly optimally oriented for thrust motion, in contrast to high-angle coseismic faults at most places. Surface outcrop and two shallow drilling studies reveal that the fault zone is several centimeters wide at most and that the coseismic slip zone during Wenchuan earthquake is about 1 mm thick. Fault zone contains foliated cataclasite, fault breccia, black gouge and yellowish gouge. Many clasts of foliated cataclasite and black gouge contained in fault breccia indicate multiple slip events along this fault. But fossils on both sides of fault do not indicate clear age difference and overall displacement along this fault should not be large. We also report results from high-velocity friction experiments conducted on yellowish gouge from the fault zone using a rotary shear low to high-velocity frictional testing apparatus. Dry experiments at normal stresses of 0.4 to 1.8 MPa and at slip rates of 0.08 to 1.35 m/s reveal dramatic slip weakening from the peak friction coeffcient of around 0.6 to very low steady-state friction coeffcient of 0.1–0.2. Slip weakening parameters of this carbonate fault zone are similar to those of clayey fault gouge from Yingxiu-Beichuan fault at Hongkou outcrop and from Pingxi fault zone. Our experimental result will provide a condition for triggering movement of subsidiary faults or off-fault damage during a large earthquake.
基金supported by State Key Laboratory of Earthquake Dynamics (project No.LED2010A03)Wenchuan Earthquake Fault Scientific Drilling Project (WFSD-09)
文摘This paper reports internal structures of a wide fault zone at Shenxigou,Dujiangyan,Sichuan province,China,and high-velocity frictional properties of the fault gouge collected near the coseismic slip zone during the 2008 Wenchuan earthquake.Vertical offset and horizontal displacement at the trench site were 2.8 m(NW side up)and 4.8 m(right-lateral),respectively.The fault zone formed in Triassic sandstone,siltstone,and shale about 500 m away from the Yingxiu-Beichuan fault,a major fault in the Longmenshan fault system.A trench survey across the coseismic fault,and observations of outcrops and drill cores down to a depth of 57 m revealed that the fault zone consists of fault gouge and fault breccia of about0.5 and 250-300 m in widths,respectively,and that the fault strikes N62°E and dips 68° to NW.Quaternary conglomerates were recovered beneath the fault in the drilling,so that the fault moved at least 55 m along the coseismic slip zone,experiencing about 18 events of similar sizes.The fault core is composed of grayish gouge(GG) and blackish gouge(BG) with very complex slip-zone structures.BG contains low-crystalline graphite of about 30 %.High-velocity friction experiments were conducted at normal stresses of 0.6-2.1 MPa and slip rates of 0.1-2.1 m/s.Both GG and BG exhibit dramatic slip weakening at constant high slip rates that can be described as an exponential decay from peak friction coefficient lpto steadystate friction coefficient lssover a slip-weakening distance Dc.Deformation of GG and BG is characterized by overlapped slip-zone structures and development of sharp slickenside surfaces,respectively.Comparison of our data with those reported for other outcrops indicates that the high-velocity frictional properties of the Longmenshan fault zones are quite uniform and the high-velocity weakening must have promoted dynamic rupture propagation during the Wenchuan earthquake.
基金supported by the National Natural Science Foundation of China (Nos. 41672268 and 41772286)the Petro China Innovation Foundation (2018D-5007-0202)the US Department of Energy (DEFE0023354)
文摘This paper experimentally explores the frictional sliding behavior of two simulated gouges:one,a series of quartz–smectite mixtures,and the other,powdered natural rocks,aiming to evaluate and codify the effect of mineralogy on gouge dilation and frictional strength,stability,and healing.Specifically,velocity-stepping and slide-hold-slide experiments were performed in a double direct shear configuration to analyze frictional constitutive parameters at room temperature,under normal stresses of 10,20,and 40 MPa.Gouge dilation was measured based on the applied step-wise changes in shear velocity.The frictional response of the quartz–smectite mixtures and powdered natural rocks are affected by their phyllosilicate content.Frictional strength and healing rates decrease with increasing phyllosilicate content,and at 20 wt.%a transition from velocity-weakening to velocity-strengthening behavior was noted.For both suites of gouges,dilation is positively correlated with frictional strength and healing rates,and negatively correlated with frictional stability.Changes in the permeability of gouge-filled faults were estimated from changes in mean porosity,indexed through measured magnitudes of gouge dilation.This combined analysis implies that the reactivation of caprock faults filled with phyllosilicaterich gouges may have a strong influence on permeability evolution in caprock faults.
文摘This paper focuses on the investigation of a hybrid seismic isolation system with passive variable friction dampers for protection of structures against near fault earthquakes. The seismic isolation can be implemented by replacing the conventional columns fixed to the foundations by seismic isolating ones. These columns allow horizontal displacement between the superstructure and the foundations and decouple the building from the damaging earthquake motion. As a result, the forces in the structural elements decrease and damage that may be caused to the building by the earthquake significantly decreases. However, this positive effect is achieved on account of displacements occurring in the isolating columns. These displacements become very large when the structure is subjected to a strong earthquake. In this case, impact may occur between the parts of the isolating column yielding their damage or collapse. In order to limit the displacements in the isolating columns, it is proposed to add variable friction dampers. A method for selecting the dampers' properties is proposed. It is carried out using an artificial ground motion record and optimal active control algorithm. Numerical simulation of a sevenstory structure shows that the proposed method allows efficient reduction in structural response and limits the displacements at the seismic isolating columns.
基金the project of National Natural Science Foundation of China (Grant No.41004037 and 41202235)
文摘Little attention had been paid to the intracontinental strike-slip faults of the Tibetan Plateau. Since the discovery of the Longriba fault using re-measured GPS data in 2003, an increasing amount of attention has been paid to this neglected fault. The local relief and transverse swath profile show that the Longriba fault is the boundary line that separates the high and flat tomography of the Tibet plateau from the high and precipitous tomography of Orogen. In addition, GPS data shows that the Longriba fault is the boundary line where the migratory direction of the Bayan Har block changed from eastward to southeastward. The GPS data shows that the Longriba fault is the boundary fault of the sub-blocks of the eastern Bayan Har block. We built three-dimensional models containing the Longriba fault and the middle segment of the Longmenshan fault, across the Bayan Har block and the Sichuan Basin. A nonlinear finite element method was used to simulate the fault behavior and the block deformation of the Eastern Tibetan Plateau. The results show that the low resistivity and low velocity layer acts as a detachment layer, which causes the overlying blocks to move southeastward. The detachment layer also controls the vertical and horizontal deformation of the rigid Bayan Har block and leads to accumulation strain on the edge of the layer where the Longmenshan thrust is located. After a sufficient amount of strain has been accumulated on the Longmenshan fault, a large earthquake occurs, such as the 2008 Wenchuan earthquake. The strike slip activity of the Longriba fault, which is above the low resistivity and low velocity layer, partitions the lateral displacements of the Bayan Har block and adjusts the direction of motion of the Bayan Har block, from the eastward moving Ahba sub-block in the west to southeastward moving Longmenshan sub-block in the east. Four models with different depths to the Longriba fault were constructed: (1) a shallow fault with a depth of only 4 km, (2) a deeper fault that is half as deep as the Longmenshan fault, (3) a deep fault that is 2 km shallower than the low resistivity and low velocity layer, and (4) a fault that is as deep as the low resistivity and low velocity layer. The activity and influence of the Longriba fault with different development stage under this tectonic system were shown: in one Earthquake recurrence period, the rupture region of the fault increases with the depth of the fault, and the lateral slip partition by the fault also changes with the fault depth. It suggests that the Longriba fault is a newly generated fault that developed after the quick uplift in Late Cenozoic along this tectonic setting and gradually extended from the northwest to southeast. The calculations provide the characteristic of block deformation and fault behaviors of intra-continental strike-slip fault and major boundary thrust faults in the eastern margin of the Tibet plateau. Although the low resistivity and low velocity layer controls the deformation of the Bayan Hat block and the uplift of the Longmenshan thrust, the partition of the Longriba fault has an important influence on the intra-plate deformation and modern geomorphic evolution.
基金sponsored by the National Natural Science Foundation of China(41874061)
文摘We monitored the amplitude changes of coda transmission waves around 500 kHz across the frictional interface of a simulated 1. 5-meter-long fault during normal stress holding test.We find that the amplitude of coda transmission waves increases with the logarithm of stationary contact time. Localized increase amounted to a level ranging from 4% to 16%along the fault is observed during the 1-hour experiment. We discuss that the frictional strength at mesoscopic scale,which is related to the amplitude of coda transmission waves,is responsible for the phenomenon. Combining the reported method with other complementary approaches will enhance the understanding of fault mechanism either at laboratory or on-site applications.
基金The research was supported by State Key Basic Science Research Project under Grant No.G1998040704 and by China Seismological Bureau, the 9th Five-year Key Research Project under the contract No. 95-04-03-02-02.
文摘To understand precursory phenomena before seismic fault sliP,this work focuses onearthquake nucleation process on a fault plane through numerical simulation.Rate and statedependent friction law with variable normal stress is employed in the analysis.The resultsshow that in the late stage of nucleation process:(1)The maximum slip velocity ismonotonically accelerating;(2)The slipping hot spot(where the slip rate is maximum)migrates spontaneously from a certain instant,and such migration is spatially continuous;(3)When the maximum velocity reaches a detectable order of magnitude(at least one orderof magnitude greater than the loading rate),the remaining time is 20 hours or longer,andthe temporal variation of slip velocity beyond this point may be used as a precursoryindicator;(4)The average slip velocity is related to the remaining time by a log-log linearrelation,which means that a similar relation between rate of microseismicity and remainingtime may also exist;(5)when normal stress variation is taken
基金supported by the China Geological Survey(No.12120114002401)Science and Technology Project(SinoP robe-06)+1 种基金Natural Science Foundation of China(No.41404080)the Central Public-Interest Scientific Institution Basal Research Fund(No.DZLXJK201404)
文摘The present-day stress state of the Yingxiu-Beichuan fault after the Wenchuan earthquake was re-estimated using measured in-situ stress data obtained after the Wenchuan earthquake. The results reveal that the gradient coefficients of principal stresses versus depth decrease from south to north along the Yingxiu-Beichuan fault, revealing that the stress level decreases from south to north. The consistency between the present-day stress levels and surface ruptures generated during the earthquake indicates that the accumulated tectonic stress beneath the Yingxiu-Beichuan fault before the Wenchuan earthquake was relieved in form of surface ruptures. This resulted in the stress remaining high in the southern section of the Yingxiu-Beichuan fault but relatively low in the northern section. Abnormal high pore pressure conditions and an extremely low frictional coefficient play important role in the interpretation of the stress field adjustment and seismic events observed after the Wenchuan earthquake along this fault, according to the estimation results using the Coulomb frictional-failure theory incorporating frictional coefficients ranging from 0.4 to 1.0. To accurately estimate the seismological hazard of the Yingxiu-Beichuan fault by analyzing fault instability using the Coulomb frictional-failure theory, much attention should be focused on the pore pressure conditions and the evolution state of the frictional coefficient under the present-day stress state.
基金supported by State Key Laboratory of Earthquake Dynamics (Project No.LED2014A06 & LED2010A05)
文摘This paper reviews 19 apparatuses having highvelocity capabilities,describes a rotary-shear low to highvelocity friction apparatus installed at Institute of Geology,China Earthquake Administration,and reports results from velocity-jump tests on Pingxi fault gouge to illustrate technical problems in conducting velocity-stepping tests at high velocities.The apparatus is capable of producing plate to seismic velocities(44 mm/a to 2.1 m/s for specimens of 40 mm in diameter),using a 22 kW servomotor with a gear/belt system having three velocity ranges.A speed range can be changed by 103 or 106by using five electromagnetic clutches without stopping the motor.Two cam clutches allow fivefold velocity steps,and the motor speed can be increased from zero to 1,500 rpm in 0.1-0.2 s by changing the controlling voltage.A unique feature of the apparatus is a large specimen chamber where different specimen assemblies can be installed easily.In addition to a standard specimen assembly for friction experiments,two pressure vessels were made for pore pressures to 70 MPa;one at room temperature and the other at temperatures to 500 °C.Velocity step tests are needed to see if the framework of rate-and-state friction is applicable or not at high velocities.We report results from velocity jump tests from 1.4 mm/s to 1.4 m/s on yellowish gouge from a Pingxi fault zone,located at the northeastern part of the Longmenshan fault system that caused the 2008 Wenchuan earthquake.An instantaneous increase in friction followed by dramatic slip weakening was observed for the yellowish gouge with smooth sliding surfaces of host rock,but no instantaneous response was recognized for the same gouge with roughened sliding surfaces.Instantaneous and transient frictional properties upon velocity steps cannot be separated easily at high velocities,and technical improvements for velocity step tests are suggested.