To investigate the influence of structural parameters on the performances and internal flow characteristics of partial flow pumps at a low specific speed of 10000 rpm,special attention was paid to the first and second...To investigate the influence of structural parameters on the performances and internal flow characteristics of partial flow pumps at a low specific speed of 10000 rpm,special attention was paid to the first and second stage impeller guide vanes.Moreover,the impeller blade outlet width,impeller inlet diameter,blade inclination angle,and number of blades were considered for orthogonal tests.Accordingly,nine groups of design solutions were formed,and then used as a basis for the execution of numerical simulations(CFD)aimed at obtaining the efficiency values and heads for each design solution group.The influence of impeller geometric parameters on the efficiency and head was explored,and the“weight”of each factor was obtained via a range analysis.Optimal structural parameters were finally chosen on the basis of the numerical simulation results,and the performances of the optimized model were verified accordingly(yet by means of CFD).Evidence is provided that the increase in the efficiency and head of the optimized model was 12.11%and 23.5 m,respectively,compared with those of the original model.展开更多
[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion metho...[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion method to evaluate the extraction rate,berberine hydrochloride content,and bacteriostatic ring diameter of the extract as comprehensive indices,and optimized the extraction process conditions of Compound Coptis Ointment using ethanol reflux.[Results]Based on the results of comprehensive indices,the optimal reflux extraction conditions for Compound Coptis Ointment were determined to be soaking in 1.5 times the amount of 70%ethanol for 2 h,followed by two extractions with 6 times the amount of 70%ethanol for 1 h each time.Three verification tests were conducted under the optimal process conditions.The yield of the extract was 28.32%±0.53%,the content of berberine hydrochloride was 4.68%±0.45%,and the diameter of the bacteriostatic ring was(2.5±0.2)cm.[Conclusions]The extract had higher drug content and exhibited better antibacterial effects.The optimized extraction process is simple,stable,and reliable,and can be effectively used to optimize the extraction process of Compound Coptis Ointment.展开更多
Through PRB simulated device and orthogonal test,we discussed the treatment effect of groundwater polluted by landfill leachate with three reaction mediums of zero-valent iron powder,activated carbon and zeolite. We c...Through PRB simulated device and orthogonal test,we discussed the treatment effect of groundwater polluted by landfill leachate with three reaction mediums of zero-valent iron powder,activated carbon and zeolite. We considered four factors of iron powder mass,activated carbon mass,particle size of iron powder and zeolite mass,and designed a two-level orthogonal test. It concluded that effluent pH appeared to fall or rise as the reaction proceeded,which changed during 7- 8. The removal rates of CODCrin eight reactors were during 60. 7%- 78. 3%,and the removal rates of NH3-N were during 34. 0%- 58. 8%. Activated carbon mass and the interaction of iron powder mass and activated carbon mass had significant influences on the removal of CODCr,while iron powder mass,particle size of iron powder and zeolite mass had insignificant influences on the removal of CODCr. Zeolite mass and activated carbon mass had significant influences on the removal of NH3,while iron powder mass,particle size of iron powder and the interaction with activated carbon mass had insignificant influences on the removal of NH3-N.展开更多
Influence of multiple structural parameters on the performance of a gun launch system driven by highpressure reactive gases is important for structural design and performance adjustment.A coupled lumped parameter mode...Influence of multiple structural parameters on the performance of a gun launch system driven by highpressure reactive gases is important for structural design and performance adjustment.A coupled lumped parameter model was utilized to predict the propellant combustion,and a dynamic finite element method was applied to approximate the mechanical interactions between the projectile and the barrel.The combustion and the mechanical interactions were coupled through a user subroutine interface in ABAQUS.The correctness and the capability of the finite element approximations in capturing small structural changes were validated by comparing predicted resistance with experiments.Based on the coupled model,the influence of structural parameters of a medium-caliber gun on the system performance was investigated.In order to reduce the research costs,orthogonal tests were designed to investigate the comprehensive effects of the parameters.According to statistical analysis,the important order of the structural parameters on the launching process was obtained.The results indicate that the influence of the width of the rotating band stands out among the studied parameters in the gun.The work provides a method to investigate the influence of multiple parameters on system performance and gives guidance for controlling the system performance.展开更多
A prototype centrifugal pump with a specific speed of 110 is used to investigate and optimize the performances of a turbine for power generation.Particular attention is given to the design of the internal impeller.The...A prototype centrifugal pump with a specific speed of 110 is used to investigate and optimize the performances of a turbine for power generation.Particular attention is given to the design of the internal impeller.The internal flow field is simulated in the framework of a commercial computational fluid dynamics software(ANSYS).Four geometrical parameters of the impeller are considered,i.e.,the inlet diameter,the inlet width,the blade number,and the blade angle.The optimization is carried out on the basis of a three-level approach relying on an orthogonal test method.The results of the numerical simulations show good agreement with the experimental tests under different flow conditions.In accordance with the L9(34)design table,the head and efficiency under the rated flow rate of the nine designed schemes are calculated and processed with the method of range analysis to obtain an optimized model.展开更多
This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test ...This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test design is applied to cutting stainless steel. Through range analysis on experiment results, the optimal process conditions for the cutting depth and the kerr ratio of the bottom width to the top width can be determined. In addition, the analysis of ranges and variances are all employed to identify various factors: traverse rate, working pressure, nozzle diameter, standoff distance which denote the importance order of the cutting parameters affecting cutting depth and the kerf ratio of the bottom width to the top width. ~rthermore, non-linear regression analysis is used to establish the mathematical models of the cutting parameters based on the cutting depth and the kerr ratio. Finally, the verification experiments of cutting parameters' effect on cutting performance, which show that optimized cutting parameters and cutting model can significantly improve the prediction of the cutting ability and quality of ASJ.展开更多
[Objectives] The research aimed to explore extraction method of Oenanthe benghalensis polysaccharide,and determine the optimal process of its ultrasonic extraction by orthogonal test. [Methods] Phenol-sulfuric acid me...[Objectives] The research aimed to explore extraction method of Oenanthe benghalensis polysaccharide,and determine the optimal process of its ultrasonic extraction by orthogonal test. [Methods] Phenol-sulfuric acid method was used to determine polysaccharide's content. Based on single-factor experiment and orthogonal test,the influences of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide were studied,and the optimal process of ultrasonic extraction was selected. [Results] The influence order of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide was A > D > B > C. Via the orthogonal test,it was determined that the optimal extraction condition of O. benghalensis polysaccharide was as below: solid-liquid ratio 1∶ 25( g/mL),extraction temperature 60℃,extraction power 80 W,extraction time 40 min. Under the condition,extraction rate of O. benghalensis polysaccharide was9. 80%. [Conclusions] The process could provide the reference basis for extracting and producing O. benghalensis polysaccharides.展开更多
[Objectives] The study aimed to optimize the extraction process of Prunellae Spica compound to provide an experimental basis for the development and utilization of the compound. [Methods]Through orthogonal test,the op...[Objectives] The study aimed to optimize the extraction process of Prunellae Spica compound to provide an experimental basis for the development and utilization of the compound. [Methods]Through orthogonal test,the optimal extraction process of Prunellae Spica compound was chosen by using the yield of dry paste and ursolic acid content as evaluation indicators. [Results]The optimal extraction process of Prunellae Spica compound is as follows: solvent dosage was 16 times,and extraction frequency was 3 times,while extraction time was 1 h.[Conclusions]The extraction process of Prunellae Spica compound was stable and feasible,and this study can provide a theoretical basis for further preparation of the compound.展开更多
With quercetin content and yield of dry extract as investigation indices, three factors, amount of water added, decoction time and decoction times were investigated by an orthogonal test, so as to select the optimal w...With quercetin content and yield of dry extract as investigation indices, three factors, amount of water added, decoction time and decoction times were investigated by an orthogonal test, so as to select the optimal water extraction process for Zihua Qinghuo Capsule. The determined extraction process was adding 8 times of water in five herbs including Viola philippica and decocting for 2 times, 1.5 h each time. Pilot scale test demonstrated that the selected process is stable and feasible, and could provide reliable reference for practical production.展开更多
Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants ment...Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants mentioned above are installed as four factors,and three levels are selected for every factor.The test is actualized according to L 9(3 4) orthogonal array.Results An optimized recipe A 3 B 3 C 3 D 1 has been obtained after considering multifarious factors such as the resources of these plants and the water-solubility of samples.Conclusion The dry powder insecticide prepared by mixing the plant samples mentioned above as 1∶1∶1mass ratio revealed that insecticidal activities for cickets,grasshopper,aphid,and 3rd instar Mythimna separata walker are significant,respectively.展开更多
In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of w...In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of warm compacted samples was studied. According to the orthogonal test method, the authors systematically study the influence of the different compaction pressure, condition of lubrication and compaction temperature on the green density of the sample in the warm compaction process, and put forward the optimal process parameter of warm compaction experiment. It is found that, a high compaction pressure (≥700 MPa), die wall lubrication combined with a small amount of internal lubricants, and fitting compaction temperature by different condition of lubrication, are the optimal parameters in warm compaction process.展开更多
[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol ...[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol times and extraction time were investigated by HPLC-MS combined with orthogonal test to optimize extraction process using the content of monoester alkaloids( the sum of benzoyl neoaconitine,benzoyl hypoaconitine and benzoyl aconitine) as an index.[Results]The optimum ethanol extraction technology was as follows: 75% ethanol,ethanol amount 25 times of the medicinal material,and each extraction for 1. 5 h.[Conclusions] The optimal extraction technology is simple,feasible,stable and reliable. It can provide reference for the industrial production and quality control of monoester alkaloids from Radix Aconiti Preparata.展开更多
In this paper, clear liquid fermentation condition for ethanol production from Canna edulis Kerl with orthogonal design was studied. We have studied five factors that influenced clear liquid fermentation condition for...In this paper, clear liquid fermentation condition for ethanol production from Canna edulis Kerl with orthogonal design was studied. We have studied five factors that influenced clear liquid fermentation condition for ethanol production from Canna edulis Kerl by the single-factor test. The five factors were α-amylase amount, glu-coamylase amount, pH, nitrogen and auxiliary materials amount. Selected the best amounts of α-amylase, glucoamylase, pH, nitrogen source and auxiliary materials by means of the singe- factors test. And then, we used the Orthogonal test to optimize the fermentation process. The study showed that the best fermentation condi-tions were α-amylase amount 7 u/g C.eduli, glu-coamylase amount 145u/g C. edulis, pH 4.4 and the amount of urea 0.08%, 1% of rice bran as auxiliary materials. The rate of alcohol which was produced by the best fermentation conditions is 21.5% that increased by 1.3% than the rate of alcohol by the single-factor test.展开更多
In gas metal arc welding(GMAW)process,the short-circuit transition was the most typical transition observed in molten metal droplets.This paper used orthogonal tests to explore the coupling effect law of welding proce...In gas metal arc welding(GMAW)process,the short-circuit transition was the most typical transition observed in molten metal droplets.This paper used orthogonal tests to explore the coupling effect law of welding process parameters on the quality of weld forming under short-circuit transition,the design of 3 factors and 3 levels of a total of 9 groups of orthogonal tests,welding current,welding voltage,welding speed as input parameters:effective area ratio,humps,actual linear power density,aspect ratio,Vickers hardness as output paramet-ers(response targets).Using range analysis and trend charts,we can visually depict the relationship between input parameters and a single output parameter,ultimately determining the optimal process parameters that impact the single output index.Then combined with gray the-ory to transform the three response targets into a single gray relational grade(GRG)for analysis,the optimal combination of the weld mor-phology parameters as follows:welding current 100 A,welding voltage 25 V,welding speed 30 cm/min.Finally,validation experiments were conducted,and the results showed that the error between the gray relational grade and the predicted value was 2.74%.It was observed that the effective area ratio of the response target significantly improved,validating the reliability of the orthogonal gray relational method.展开更多
The robust parameter design method is a traditional approach to robust experimental design that seeks to obtain the optimal combination of factors/levels. To overcome some of the defects of the inflatable wing paramet...The robust parameter design method is a traditional approach to robust experimental design that seeks to obtain the optimal combination of factors/levels. To overcome some of the defects of the inflatable wing parameter design method, this paper proposes an optimization design scheme based on orthogonal testing and support vector machines (SVMs). Orthogonal testing design is used to estimate the appropriate initial value and variation domain of each variable to decrease the number of iterations and improve the identification accuracy and efficiency. Orthogonal tests consisting of three factors and three levels are designed to analyze the parameters of pressure, uniform applied load and the number of chambers that affect the bending response of inflatable wings. An SVM intelligent model is established and limited orthogonal test swatches are studied. Thus, the precise relationships between each parameter and product quality features, as well the signal-to-noise ratio (SNR), can be obtained. This can guide general technological design optimization.展开更多
Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the ef...Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the efficiency of smashing tissue extraction (STE). Solid-liquid ratio, extracting times, ethanol concentration, and extracting time were investigated through orthogonal test. Results The optimized conditions for STE were ten times amount of 80% EtOH, extracting for three times, and 2 min for each time. Conclusion STE could obtain relatively higher yield, simplicity of operation, and benefit for environment protection. It could be better choice for the extraction of S. chinensis.展开更多
To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diamet...To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.展开更多
Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract ...Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract bioactive polyphenols from E. prolifra through orthogonal L16(4)5 test. Results The highest yield (0.923 ± 0.013) mg/g was obtained when microwave power, solvent to raw material ratio, irradiation time, ethanol concentration, and extraction cycles were 500 W, 25 mL/g, 25 min, 40%, and 3, respectively, which was higher than that of Soxhlet extraction with methanol for 6 h, ultrasound-assisted extraction with 40% ethanol for 1 h twice and heat reflux extraction with 40% ethanol for 2 h twice. Conclusion This finding indicates that MAE is a superior technique for the extraction of polyphenols due to less impurity, higher time efficiency and yield.展开更多
基金National Key R&D Program of China(Grant No.2020YFC1512404).
文摘To investigate the influence of structural parameters on the performances and internal flow characteristics of partial flow pumps at a low specific speed of 10000 rpm,special attention was paid to the first and second stage impeller guide vanes.Moreover,the impeller blade outlet width,impeller inlet diameter,blade inclination angle,and number of blades were considered for orthogonal tests.Accordingly,nine groups of design solutions were formed,and then used as a basis for the execution of numerical simulations(CFD)aimed at obtaining the efficiency values and heads for each design solution group.The influence of impeller geometric parameters on the efficiency and head was explored,and the“weight”of each factor was obtained via a range analysis.Optimal structural parameters were finally chosen on the basis of the numerical simulation results,and the performances of the optimized model were verified accordingly(yet by means of CFD).Evidence is provided that the increase in the efficiency and head of the optimized model was 12.11%and 23.5 m,respectively,compared with those of the original model.
基金Supported by Key Research Project of Wuhan Municipal Health Commission(WZ21A08).
文摘[Objectives]To determine the optimal reflux extraction process conditions for Compound Coptis Ointment.[Methods]The study employed the orthogonal experimental design method and drug-sensitive disc agar diffusion method to evaluate the extraction rate,berberine hydrochloride content,and bacteriostatic ring diameter of the extract as comprehensive indices,and optimized the extraction process conditions of Compound Coptis Ointment using ethanol reflux.[Results]Based on the results of comprehensive indices,the optimal reflux extraction conditions for Compound Coptis Ointment were determined to be soaking in 1.5 times the amount of 70%ethanol for 2 h,followed by two extractions with 6 times the amount of 70%ethanol for 1 h each time.Three verification tests were conducted under the optimal process conditions.The yield of the extract was 28.32%±0.53%,the content of berberine hydrochloride was 4.68%±0.45%,and the diameter of the bacteriostatic ring was(2.5±0.2)cm.[Conclusions]The extract had higher drug content and exhibited better antibacterial effects.The optimized extraction process is simple,stable,and reliable,and can be effectively used to optimize the extraction process of Compound Coptis Ointment.
基金Supported by Natural Science Foundation Project of Shandong Province,China(2013ZRA16006)Science Research Foundation Project of Binzhou University,China(BZXYG1108)
文摘Through PRB simulated device and orthogonal test,we discussed the treatment effect of groundwater polluted by landfill leachate with three reaction mediums of zero-valent iron powder,activated carbon and zeolite. We considered four factors of iron powder mass,activated carbon mass,particle size of iron powder and zeolite mass,and designed a two-level orthogonal test. It concluded that effluent pH appeared to fall or rise as the reaction proceeded,which changed during 7- 8. The removal rates of CODCrin eight reactors were during 60. 7%- 78. 3%,and the removal rates of NH3-N were during 34. 0%- 58. 8%. Activated carbon mass and the interaction of iron powder mass and activated carbon mass had significant influences on the removal of CODCr,while iron powder mass,particle size of iron powder and zeolite mass had insignificant influences on the removal of CODCr. Zeolite mass and activated carbon mass had significant influences on the removal of NH3,while iron powder mass,particle size of iron powder and the interaction with activated carbon mass had insignificant influences on the removal of NH3-N.
基金the financial support from the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYLX_0399)
文摘Influence of multiple structural parameters on the performance of a gun launch system driven by highpressure reactive gases is important for structural design and performance adjustment.A coupled lumped parameter model was utilized to predict the propellant combustion,and a dynamic finite element method was applied to approximate the mechanical interactions between the projectile and the barrel.The combustion and the mechanical interactions were coupled through a user subroutine interface in ABAQUS.The correctness and the capability of the finite element approximations in capturing small structural changes were validated by comparing predicted resistance with experiments.Based on the coupled model,the influence of structural parameters of a medium-caliber gun on the system performance was investigated.In order to reduce the research costs,orthogonal tests were designed to investigate the comprehensive effects of the parameters.According to statistical analysis,the important order of the structural parameters on the launching process was obtained.The results indicate that the influence of the width of the rotating band stands out among the studied parameters in the gun.The work provides a method to investigate the influence of multiple parameters on system performance and gives guidance for controlling the system performance.
基金This work was supported by the National Natural Science Foundation of China under Grant 51605200the Senior Talent Start-up Foundation of Jiangsu University under Grant 14JDG145.
文摘A prototype centrifugal pump with a specific speed of 110 is used to investigate and optimize the performances of a turbine for power generation.Particular attention is given to the design of the internal impeller.The internal flow field is simulated in the framework of a commercial computational fluid dynamics software(ANSYS).Four geometrical parameters of the impeller are considered,i.e.,the inlet diameter,the inlet width,the blade number,and the blade angle.The optimization is carried out on the basis of a three-level approach relying on an orthogonal test method.The results of the numerical simulations show good agreement with the experimental tests under different flow conditions.In accordance with the L9(34)design table,the head and efficiency under the rated flow rate of the nine designed schemes are calculated and processed with the method of range analysis to obtain an optimized model.
基金supported by the Science and Technology Development Foundation of Shanghai Municipal Science and Technology Commission (Grant No.037252022)
文摘This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test design is applied to cutting stainless steel. Through range analysis on experiment results, the optimal process conditions for the cutting depth and the kerr ratio of the bottom width to the top width can be determined. In addition, the analysis of ranges and variances are all employed to identify various factors: traverse rate, working pressure, nozzle diameter, standoff distance which denote the importance order of the cutting parameters affecting cutting depth and the kerf ratio of the bottom width to the top width. ~rthermore, non-linear regression analysis is used to establish the mathematical models of the cutting parameters based on the cutting depth and the kerr ratio. Finally, the verification experiments of cutting parameters' effect on cutting performance, which show that optimized cutting parameters and cutting model can significantly improve the prediction of the cutting ability and quality of ASJ.
基金Supported by Chinese Medicine Chemistry Construction Project in"12th Fiveyear" Key Disciplines of Chinese Medicine,State Administration of Traditional Chinese Medicine(Guozhongyiyaorenjiaofa[2012]32)Pharmaceutical Chemistry Construction Project of Guangxi Key Discipline(Guijiaokeyan[2013]16)+1 种基金Construction Program of Technology Innovation Capability Upgrading Project in Guangxi Colleges and Universities(Guijiaokeyan[2015]5)Student's Platform for Innovation and Entrepreneurship Training Program in Youjiang Medical University for Nationalities in 2017(201710599110)
文摘[Objectives] The research aimed to explore extraction method of Oenanthe benghalensis polysaccharide,and determine the optimal process of its ultrasonic extraction by orthogonal test. [Methods] Phenol-sulfuric acid method was used to determine polysaccharide's content. Based on single-factor experiment and orthogonal test,the influences of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide were studied,and the optimal process of ultrasonic extraction was selected. [Results] The influence order of solid-liquid ratio( A),ultrasonic extraction temperature( B),ultrasonic power( C) and ultrasonic time( D) on extraction rate of O. benghalensis polysaccharide was A > D > B > C. Via the orthogonal test,it was determined that the optimal extraction condition of O. benghalensis polysaccharide was as below: solid-liquid ratio 1∶ 25( g/mL),extraction temperature 60℃,extraction power 80 W,extraction time 40 min. Under the condition,extraction rate of O. benghalensis polysaccharide was9. 80%. [Conclusions] The process could provide the reference basis for extracting and producing O. benghalensis polysaccharides.
基金Supported by Talent Training and Construction Project of Professor Yang Shilin’s Team in 2017(YSL17010)
文摘[Objectives] The study aimed to optimize the extraction process of Prunellae Spica compound to provide an experimental basis for the development and utilization of the compound. [Methods]Through orthogonal test,the optimal extraction process of Prunellae Spica compound was chosen by using the yield of dry paste and ursolic acid content as evaluation indicators. [Results]The optimal extraction process of Prunellae Spica compound is as follows: solvent dosage was 16 times,and extraction frequency was 3 times,while extraction time was 1 h.[Conclusions]The extraction process of Prunellae Spica compound was stable and feasible,and this study can provide a theoretical basis for further preparation of the compound.
基金Supported by Guiyang Science and Technology Planning Project(ZKHT[2017-4]21)
文摘With quercetin content and yield of dry extract as investigation indices, three factors, amount of water added, decoction time and decoction times were investigated by an orthogonal test, so as to select the optimal water extraction process for Zihua Qinghuo Capsule. The determined extraction process was adding 8 times of water in five herbs including Viola philippica and decocting for 2 times, 1.5 h each time. Pilot scale test demonstrated that the selected process is stable and feasible, and could provide reliable reference for practical production.
文摘Aim To prepare dry powder insecticide by mixing the plant samples of Aconitum ochranthum Mey.,Aconitum hemsleyanum Pritz.and Dictamnus dasycarpus Turcz.Method The dosage ratios of the break stocks from the plants mentioned above are installed as four factors,and three levels are selected for every factor.The test is actualized according to L 9(3 4) orthogonal array.Results An optimized recipe A 3 B 3 C 3 D 1 has been obtained after considering multifarious factors such as the resources of these plants and the water-solubility of samples.Conclusion The dry powder insecticide prepared by mixing the plant samples mentioned above as 1∶1∶1mass ratio revealed that insecticidal activities for cickets,grasshopper,aphid,and 3rd instar Mythimna separata walker are significant,respectively.
基金the National Scientific and Technological Project(No.MKPT-2004-09ZD)the Innovative Engineering Program of Central South University
文摘In order to achieve higher density of P/M steels using the die wall lubrication compacting method or powder lubricant in warm compaction process, the influence of different process parameters on the green density of warm compacted samples was studied. According to the orthogonal test method, the authors systematically study the influence of the different compaction pressure, condition of lubrication and compaction temperature on the green density of the sample in the warm compaction process, and put forward the optimal process parameter of warm compaction experiment. It is found that, a high compaction pressure (≥700 MPa), die wall lubrication combined with a small amount of internal lubricants, and fitting compaction temperature by different condition of lubrication, are the optimal parameters in warm compaction process.
基金Supported by Traditional Chinese Medicine Science and Technology Development Program of Shandong Province (2017-1982019-0400)Major Science and Technology Innovation Project of Shandong Province (2018CXGC1304)。
文摘[Objectives] This study was conducted to optimize the ethanol extraction technology of monoester alkaloids from Radix Aconiti Preparata. [Methods]On the basis of defined extraction times,ethanol concentration,ethanol times and extraction time were investigated by HPLC-MS combined with orthogonal test to optimize extraction process using the content of monoester alkaloids( the sum of benzoyl neoaconitine,benzoyl hypoaconitine and benzoyl aconitine) as an index.[Results]The optimum ethanol extraction technology was as follows: 75% ethanol,ethanol amount 25 times of the medicinal material,and each extraction for 1. 5 h.[Conclusions] The optimal extraction technology is simple,feasible,stable and reliable. It can provide reference for the industrial production and quality control of monoester alkaloids from Radix Aconiti Preparata.
文摘In this paper, clear liquid fermentation condition for ethanol production from Canna edulis Kerl with orthogonal design was studied. We have studied five factors that influenced clear liquid fermentation condition for ethanol production from Canna edulis Kerl by the single-factor test. The five factors were α-amylase amount, glu-coamylase amount, pH, nitrogen and auxiliary materials amount. Selected the best amounts of α-amylase, glucoamylase, pH, nitrogen source and auxiliary materials by means of the singe- factors test. And then, we used the Orthogonal test to optimize the fermentation process. The study showed that the best fermentation condi-tions were α-amylase amount 7 u/g C.eduli, glu-coamylase amount 145u/g C. edulis, pH 4.4 and the amount of urea 0.08%, 1% of rice bran as auxiliary materials. The rate of alcohol which was produced by the best fermentation conditions is 21.5% that increased by 1.3% than the rate of alcohol by the single-factor test.
基金supported by Major Special Projects of Science and Technology in Fujian Province,(Grant No.2020HZ03018)Natural Science Foundation of Fujian Province(Grant No.2020J01873).
文摘In gas metal arc welding(GMAW)process,the short-circuit transition was the most typical transition observed in molten metal droplets.This paper used orthogonal tests to explore the coupling effect law of welding process parameters on the quality of weld forming under short-circuit transition,the design of 3 factors and 3 levels of a total of 9 groups of orthogonal tests,welding current,welding voltage,welding speed as input parameters:effective area ratio,humps,actual linear power density,aspect ratio,Vickers hardness as output paramet-ers(response targets).Using range analysis and trend charts,we can visually depict the relationship between input parameters and a single output parameter,ultimately determining the optimal process parameters that impact the single output index.Then combined with gray the-ory to transform the three response targets into a single gray relational grade(GRG)for analysis,the optimal combination of the weld mor-phology parameters as follows:welding current 100 A,welding voltage 25 V,welding speed 30 cm/min.Finally,validation experiments were conducted,and the results showed that the error between the gray relational grade and the predicted value was 2.74%.It was observed that the effective area ratio of the response target significantly improved,validating the reliability of the orthogonal gray relational method.
文摘The robust parameter design method is a traditional approach to robust experimental design that seeks to obtain the optimal combination of factors/levels. To overcome some of the defects of the inflatable wing parameter design method, this paper proposes an optimization design scheme based on orthogonal testing and support vector machines (SVMs). Orthogonal testing design is used to estimate the appropriate initial value and variation domain of each variable to decrease the number of iterations and improve the identification accuracy and efficiency. Orthogonal tests consisting of three factors and three levels are designed to analyze the parameters of pressure, uniform applied load and the number of chambers that affect the bending response of inflatable wings. An SVM intelligent model is established and limited orthogonal test swatches are studied. Thus, the precise relationships between each parameter and product quality features, as well the signal-to-noise ratio (SNR), can be obtained. This can guide general technological design optimization.
基金E&T modern center for Natural Products of Liaoning Province of China (2008402021)
文摘Objective To optimize the extract technology of active lignins from the fruits of Schisandra chinensis. Methods The content of schizandrin, gomisin A, and deoxyschizandrin were selected as standards to evaluate the efficiency of smashing tissue extraction (STE). Solid-liquid ratio, extracting times, ethanol concentration, and extracting time were investigated through orthogonal test. Results The optimized conditions for STE were ten times amount of 80% EtOH, extracting for three times, and 2 min for each time. Conclusion STE could obtain relatively higher yield, simplicity of operation, and benefit for environment protection. It could be better choice for the extraction of S. chinensis.
基金financially supported by the Program for New Century Excellent Talents in University(NCET-12-0849)the Fundamental Research Funds for the Central Universities(13ZD12)the National Natural Science Foundation of China(No.51006034)
文摘To provide theoretical basis and practical guidance for preparing composite rods by direct continuous casting, copper-clad aluminum composite rods of external copper layer diameter 12 mm and inner aluminum core diameter 8 mm were manufactured. Orthogonal tests consisted of three factors and three levels were carried out to research the effects of melting copper temperature, continuous casting speed and nitrogen pressure on the performance of composite rods. Results showed that nitrogen pressure is the most important factor in influencing the surface quality; continuous casting speed is the most important factor in influencing copper & aluminum inter diffusion amount. Nitrogen pressure can noticeably improve the surface quality and make the rods easily be drawn out, but the surface quality does not show visible improvement when the nitrogen pressure is above 0.05 MPa. Measured by tests, the compound layer can be divided into three types according to its cladding layer degree: deficient cladding, normal cladding and excess cladding. The diameter of normal copper-clad aluminum composite rods can be successfully drawn less than 0.6 mm without annealing.
基金National High Technology Development Project (863 project) (2007AA091701)Zhejiang Provincial Natural Science Foundation (Y2080579)Important Project of Zhejiang Ocean University (21135030107)
文摘Objective To optimize microwave-assisted extraction of polyphenols from Enteromorpha prolifra. Methods Based on single-factor tests, an efficient microwave-assisted extraction (MAE) technique was developed to extract bioactive polyphenols from E. prolifra through orthogonal L16(4)5 test. Results The highest yield (0.923 ± 0.013) mg/g was obtained when microwave power, solvent to raw material ratio, irradiation time, ethanol concentration, and extraction cycles were 500 W, 25 mL/g, 25 min, 40%, and 3, respectively, which was higher than that of Soxhlet extraction with methanol for 6 h, ultrasound-assisted extraction with 40% ethanol for 1 h twice and heat reflux extraction with 40% ethanol for 2 h twice. Conclusion This finding indicates that MAE is a superior technique for the extraction of polyphenols due to less impurity, higher time efficiency and yield.