Optical coherence transfer over 50-km spooled fiber with frequency instability of 2×10^(-17) at 1s

We demonstrate coherent transfer of an ultra-stable optical frequency at 192.8 THz over 50-km spooled fiber. Random phase noise induced by environmental disturbance through fiber is detected and suppressed by feeding a correctional signal into an acousto-optic modulator. After being compensated, the fiber-induced frequency instability is 2×10-17 at 1-s averaging time and reaches 8×10-20 after 16 h. The noise floor of the compensation system could be as low as 2×10-18 at 1-s averaging time.

Interfacial stress transfer behavior in a specially-shaped fiber/matrix pullout test

Specially designed fibers are widely used in engineering practice because the specially-designed shape can help to improve the bonding strength of the fiber and the interface. Studied in this paper is the interfacial shear stress transfer behavior on both sides of the specially designed fiber when it is being pulled out; in which automatic analysis of three-dimensional photoelasticity is employed and the finite element method is adopted. The results show that the stress transfer occurs mainly in the region near the fiber＇s embedded end where the stress reaches its critical point, leading to debonding of the interface. Before debonding, as the pullout loading increases, the peak value of shear stress transfers along the fiber from the embedded end to the interior of the matrix, and then stops at the hooked part of the fiber because of its impediment. When the interface begins to debond as the load increases, the shear stress can be transferred to the hooked part.

Determination of the orthometric height difference based on optical fiber frequency transfer technique

The development of remote frequency transfer techniques,especially the appearance of optical clocks with unprecedented stability,has prompted geoscientists to study their applications in geodesy.Using remote frequency transfer technique,by frequency comparison of two optical clocks at two points P and Q connected by optical fibers,one can measure the signal’s frequency shift between them,and the geopotential difference between them can be determined based on the gravity frequency shift equation.Given the orthometric height of P,the orthometric height of Q can be determined.Since the present stability of the optical clock has achieved 1×10^(-18) or better and comparing the frequency transfer via optical fiber provides stability at 10^(-19) level,the optical clock network enables determining the orthometric height at centimeter-level.This study provides a formulation to determine the height diffe rence at one-centimeter level between two points on the ground based on the optical fiber frequency transfer technique.

Some Further Considerations about the Theory of Elastic Stress Transfer from Partially Embedded Axially Loaded Fiber to Matrix

In this paper the elastic stress transfer from the fiber to the matrix is analysed for fiber-reinforced composites when the fiber is loaded axially.The dependence of the elastic stress transfer on the as- pect ratio of the fiber,the volume fraction of the fiber,the fiber-to-matrix elastic modulus ratio and the Poisson's ratio of the fiber and the matrix has been shown in detail.

Effect of Polyvinylidene Fluoride Hollow Fiber Membranes on Mass Transfer of Samarium

The influence of swelling and stripping acidity on the mass transfer coefficient based on water phase and the inner diameters of membranes were studied with P507-HCl-Sm as working system in the two different kinds of hollow fiber membranes. Effects of extractant concentration, H+ concentration in aqueous phase and Sm3+ concentration on extraction rate were discussed and the corresponding reaction series were obtained. According to the investigations on the interfacial kinetics, the reaction kinetics equation and reaction rate constant were obtained.

Effect of Heat Transfer Coefficient on the Temperature Gradient for Hollow Fiber

The heat transfer coefficient h caused by blowing affects the heat transfer of fiber greatly. Especially,unsymmetrical blowing forms the unsymmetrical temperature gradient on the fiber cross.section. Based on the results of spinning simulation by computer, the changes of heat transfer coefficient on the cross-section along the spinning line and the effects on distributions of temperature gradients were discussedl It is showed that for the spinning simulation of hollow fiber under strong blowing condition, the heat transfer coetticient should bemodified as: h=0.437×10-4[ G/Vρ ( R2/ R2-n2 ) ] -o.333(V2+ 64( VYsin (θ))2)0.

Electrolyte transfer separation of hollow fiber composite nanofiltration membrane

Using Donnan Steric Partitioning Model(DSPM),the data for the rejection of four salts having common co-ion(LiCl, NaCl,KCl,Na2SO4)were obtained and they show the characters of the polyethersulfone(PES)nanofiltration(NF)membrane in terms of three parameters:an effective pore radius(rp),the ratio of effective thickness over porosity(λ/Ak)and an effective charge density(X).Good agreement between experimental data and prediction data using the three parameters mentioned above was obtained.A theoretical model was developed to predict the transport performance of electrolyte through the hollow fiber composite NF membrane.The model prediction is in good agreement with experimental results based on the method by modern numerical solution.

Reversible addition-fragmentation chain transfer graft polymerization of acrylonitrile onto PE/PET composite fiber initiated by γ-irradiation

Reversible addition-fragmentation chain transfer(RAFT) mediated grafting of acrylonitrile onto Polyethylene/Poly(ethylene terephthalate)(PE/PET) composite fibers was performed using γ-irradiation as the initial source at ambient temperature. Different initial concentrations of 2-cyanoprop-2-yl dithiobenzonate were used as the chain transfer agent. The kinetics of graft polymerization is in accordance with the living RAFT polymerization. The successful grafting of acrylonitrile is proved by Fourier transform infrared spectroscopy analysis.The results of monofilament tensile test show that mechanical properties of the fibers change slightly after grafting. Scanning electronic microscopy images of the fibers show that the surface of RAFT grafted fibers is smoother than that of fibers grafted conventionally.

Effects of Matrix Features on Stress Transfer of Short Fiber Composites

By employing the elastic and elastic plastic finite element method(FEM), the effects of matrix feature on the stress transfer mechanisms of short fiber composites are studied. In the calculation, the variations in matrix modulus, yield strength and hardening modulus are considered. It is concluded that large deformation of matrix is harmful to the improvement of the mechanical performances of the composites.

Transferring an N-atom state between two distant cavities via an optical fiber

This paper proposes a scheme for transferring an N-atom state between two distant cavities via an optical fiber. The scheme is based on adiabatic passage along a dark state. In the scheme, all the atoms are always in ground state, the field mode of the fiber remains in vacuum state, and the field mode of the cavities being excited can be negligible under certain conditions. Therefore, the scheme is very robust against decoherence. The successful probability of implementing the quantum state transfer increases with increasing number of atoms. Furthermore, the interaction time does not need to be accurately adjusted as long as the adiabaticity condition is fulfilled.

Extraction of Neodymium by Emulsion-Liquid-Membrane within Hollow-Fiber-contactor and Its Mass Transfer Properties

A non-dispersive extraction technique, using an emulsion liquid membrane within a hollow-fiber-contactor for the extraction and enrichment of Nd^3＋ from the dilute feed aqueous, was applied. The emulsion system is consisted of span80 [ sorbitian monooleate], paraffin oil, D2EHPA [ 2-（ 2-ethylhexyl- phosphonic acid）], kerosene as well as HCl solution. The extraction under various conditions such as the span80 concentrations, the flow rate of aqueous, the extraction time and HCl concentrations in receiving phase were studied. Results show that the lower the flow rates of aqueous are, the higher the extraction percentage and enrichment-fold are, and the extraction percentage increases with the increasing of HCl concentrations. When the initial Nd^3＋ concentration in feed is maintained at 1000 mg· L^-1 and the emulsion is recycled with 70 times by a counter-flow,

Study at Two Dimensions of Thermal Transfer through a Fibers Panel Subjected to Climatic Constraints in Dynamic Frequency Regulations Established

From resolution of two-dimensional equation of heat in dynamic frequency regime, we have plotted evolution curves of temperature according to depth of material or in lateral direction. They will allow us to evaluate thermal behavior of towed material. Aim of study is to use fibers as a thermal insulating material by proposing a method for determining effective thermal insulation layer in dynamic frequency regime.

砂土压缩变形传感光缆耦合试验分析与预测模型研究

灾害监测、预测是地质与岩土工程领域一项极为重要的任务。分布式光纤传感技术凭借其连续、实时、抗干扰、稳定性好等优点在长距离、长周期、高隐蔽性、强突发性的灾害监测中发挥了显著的作用。然而,针对不同工程问题,评价与解决传感光缆与被测岩土体协调变形问题,是精细化分析岩土体变形分布与研究演化规律的关键所在。利用自主研制的三维主动变形可控围压光缆-砂土耦合试验装置,探究了0~4.0MPa围压条件下金属基索传感光缆与粗砂介质压缩变形的协调性问题。试验结果表明:低围压条件下金属基索传感光缆与砂土压缩变形协调性较差,变形表现为非线性变化特征;随着围压增大,传感光缆与砂土耦合效果提高,变形呈现线性变化特征,当围压达到1.6MPa后,两者协调变形一致性明显提高,其形变由非线性向线性转变。基于上述变形特性,提出了一种围压曲面投影数值模型,采用非扭结边界条件的样条插值算法对非试验数据实际位移进行预测,结果表明该模型具有较好的可靠性。试验研究认为金属基索光缆用于高围压条件下砂土变形测试具有更高的准确性,研究内容可以为分布式光纤传感测试技术用于深部地层变形监测提供科学的参考依据。

THE MASS TRANSFER BEHAVIORS OF FE(Ⅲ), CO(Ⅱ) AND NI(Ⅱ) IN SULFURIC ACID WITH CYANEX302 BY USINGMICROPOROUS HOLLOW FIBER

In this paper the mass transfer behaviors of Fe(Ⅲ), Co(Ⅱ) and Ni(Ⅱ) with Cyanex302(bis(2,4,4- trimethylpentyl)monothiophosphinic acid) from sulfate medium by using hollow fiber membrane in counter-currently circulating operation were studied. The effect of acidity in aqueous solution and the extractant concentration on the mass transfer coefficient (Kw) was discussed. The reaction mechanism of membrane extraction was considered as a false one series reaCtion and the rate controlling step was membrane resistance. When the value of Kw arrived at 1.0 × 10-6 m/s, △pH:CoFe equaled tO 6.225, and △pH:NiFe was bigger than △p HCoFe.

谐振式光纤陀螺谐振腔传输模型仿真方法

谐振式光纤陀螺(RFOG)是一种以光纤环形谐振腔为核心敏感器件的惯性传感器。为提高仿真效率和适用性,提出了一种谐振式光纤陀螺快速运算仿真方法,搭建了谐振式光纤陀螺信号处理和闭环控制模型,其中模拟谐振腔多圈干涉耦合采用多核并行运算,包含光场叠加和传递函数两种形式。仿真结果表明所提方法仿真效率较高,平均在16s左右完成仿真,相比于原始模型的锁频程序运行效率提升了57.6%。同时两种仿真形式均适用于精度范围0.0001~1(°)/√h的谐振光纤陀螺仿真,有效适应不同仿真参数的测试要求。其中传递函数形式相较于光场叠加形式仿真效率提升了5.4倍,在±600(°)/s动态范围内标度因数非线性度降低了17%,而光场叠加形式的零偏不稳定性减小到0.652(°)/h,易于观察偏振波动误差特性。

考虑信息泄露影响的光纤传感网络传输数据安全导入方法

为了提高对光纤传感网络传输数据安全传输能力,提出基于信息泄漏加密传输的光纤传感网络传输数据安全导入方法。采用离散混沌时间序列同步调制方法实现对光纤传感网络传输数据导入过程中调制编码处理,根据混沌随机编码特性实现对光纤传感网络传输数据过程中的同步输出稳定性调节和自主随机编码,构建光纤传感网络信息传输泄漏抑制的加密密钥,通过Logistics映射实现对光纤传感网络传输数据导入过程中的信息泄漏加密重传,根据光纤传感网络传输数据的混合敏感密钥表征和算术编码,实现信息泄漏控制和数据安全导入。实验结果表明,采用该方法进行光纤传感网络传输数据导入的加密性能较好,其光纤传感网络传输数据已加密比特序列的识别率为98%,误码率仅为2.7∗10-9%,抗泄漏能力达到了0.970,并且导入后的数据完整度达到了0.996,说明该方法具备了较强的加密效果、抗泄漏能力,实现数据的安全导入和加密传输。

基于能量流向的变压器饼式绕组散热分析及试验研究

变压器热点温度作为运行经济性、安全性的关键指标,是设备在线监测及状态评估中的重点。该文对变压器内部散热进行研究,着眼于饼式绕组及其油道结构,基于能量流向建立绕组温度变化的物理模型。基于这一模型,在一台内置分布式传感光纤的110kV三相ONAN变压器上开展试验研究,使用分布式光纤测温(distributed temperature sensing,DTS)技术对运行状况下的绕组整体温度分布进行实时监测,分析绕组在ONAN冷却方式下的散热状况。在变压器启动初期,绕组各处散热量较低,温升速率较快。约2 h后,各饼散热量基本与损耗相一致,散热率可达98%以上,因此将这一阶段称为准稳态。准稳态阶段,绕组整体散热率基本一致。负载变化前期不同位置散热量的差异是温度梯度形成的主要原因。基于DTS手段及散热器进出口处油温,提出绕组每饼平均对流换热系数的计算方法,基于无量纲数建立绕组内外表面局部对流换热系数的计算方法,对不同位置、负载率下两种对流换热系数的变化规律进行分析获得了绕组运行过程中对流换热系数分布规律及变化趋势。

长距离输调水工程大口径FRPM管道研发与工程安全保障技术

长距离输调水工程是中国新疆地区重要的基础生命线,其长久稳定运行对于促进经济平稳增长和保障居民供水安全至关重要。新疆位居大陆中心,属温带极端大陆性气候,其长距离输调水工程面临严峻的环境挑战。玻璃纤维增强塑料夹砂管(glass fiber reinforced plastic mortar pipes,FRPM)作为长距离输调水工程中重要的水工地下结构用材,凭借其优异的耐化学腐蚀、轻质高强、无二次污染、安装方便、综合造价低等诸多优良特性而被广泛应用于新疆地区。然而,传统FRPM管生成工艺在铺层设计与生产自动化程度方面存在一定局限,导致工程施工过程效率低下;同时,缺少统一的技术标准和设计规范也间接制约了其应用范围。此外,管道工程自动巡检技术与缺陷定量评价标准尚未统一,无法合理量化和准确评价整体工程质量。为此,依托北疆小洼槽供水工程,围绕长距离大口径FRPM管的管材铺层设计与制造工艺、工程设计、质量评定、自动巡检、运行监测与安全保障等关键技术,通过产学研用相结合,持续15年攻关,取得突破性创新成果:①引进吸收并创新了适合于长距离、高工作压力、以连续缠绕工艺为首选的FRPM管生产工艺,优化了大口径FRPM管材铺层设计方法,实现了供料—缠绕—固化—切割—检测全自动化控制,与国外同类产品标准相比,管道挠曲性能和轴向拉伸强度等提高了20%~50%;②提出了安全防护的工程和非工程措施,建立了长距离FRPM管不同缺陷类型危害性等级划分原则,创建了复杂地质条件下长距离FRPM管道工程安全评价理论与方法;③系统揭示了FRPM管质量缺陷产生机理,开发了FRPM管光固化片材局部修复工艺以及内衬聚乙烯(PE)的整体非开挖修复技术,提出了修复效果后评价方法,实现了对长距离FRPM管道工程运行安全的有效掌控。

激光辐照碳纤维温度均匀性仿真分析

为解决激光辐照碳纤维温度不均匀引起的石墨化不均匀、模量差别大的问题,利用COMSOL软件建立了高斯与平顶激光辐照碳纤维热传导-热对流-热辐射的仿真模型,对比分析了高斯光强和平顶光强激光辐照碳纤维的升温特性以及温度分布,研究了不同激光辐照下,碳纤维的表面、截面温度分布以及达到烧蚀温度后碳纤维的烧蚀情况。实验结果表明:平顶激光辐照碳纤维的表面、截面温度分布较高斯激光更均匀,整体温差更小;不同激光辐照碳纤维的烧蚀深度呈线性变化,并且平顶激光辐照碳纤维的烧蚀速率更小。因此,平顶激光相较于高斯激光可控性更高,辐照碳纤维的温差更小,使其石墨化程度更均匀。

中空纤维膜臭氧接触式反应器传质机理分析

将疏水性聚四氟乙烯(PTFE)中空纤维膜组装成膜接触器,开发了膜接触式臭氧(O_(3))传质技术。对比了气泡传质和膜接触传质的差异,通过O_(3)传质模型和阻力模型对该技术的主要影响因素和传质机理进行了研究。结果表明,O_(3)可以有效地通过疏水性PTFE膜进行传质,当搅拌速度达到1500r/min时,膜传质的表观传质系数(0.3049min-1)与气泡传质(0.3109min-1)相当。同时,膜表面的疏水结构将尾气的湿度降低到0.8g/m^(3)以下,远低于气泡传质(>11.5g/m^(3)),符合进入臭氧发生器的标准,具备回收氧气的可行性。O_(3)的传质通量受液体流速、p H、污染物浓度、气体流量以及进气O_(3)浓度的影响。在pH=11、苯酚浓度为0或pH=7、苯酚浓度为20mg/L时,传质通量达到了0.16g/(m^(2)·h)。O_(3)传质过程的传质阻力主要由膜阻力和液相阻力组成,而通过液相条件控制可以有效减小液相阻力,因此进一步降低传质阻力需要膜技术的发展。