Field emission digital display tube with nano-graphite film cathode

The field emission digital display tube with a nano-crystalline graphite cold cathode is designed and fabricated. Under the control of the driving circuits, a dynamic digital display with uniform luminance distribution is realized. The luminance of the character segments is 190 cd/m2 at the operating voltage of 900 V. And the stable emission is attained with a fluctuation of about 3% at an average segment current of 75 μA. The results demonstrate that nano-crystalline graphite film is a promising material for cold cathode.

Improved field emission properties of carbon nanotube cathodes by nickel electroplating and corrosion

Carbon nanotube（CNT） cathodes prepared by electrophoretic deposition were treated by a combination of nickel electroplating and cathode corrosion technologies.The characteristics of the samples were measured by scanning electron microscopy,energy dispersive X-ray spectroscopy,J-E and F-N plots.After the treatment,the CNT cathodes showed improved field emission properties such as turn-on field,threshold electric field,current density,stability and luminescence uniformity.Concretely,the turn-on field decreased from 0.95 to 0.45 V/μm at an emission current density of 1 mA/cm^2,and the threshold electric field decreased from 0.99 to 0.46 V/μm at a current density of 3 mA/cm^2.The maximum current density was up to 7 mA/cm2 at a field of 0.48 V/μm.In addition,the current density of the CNT cathodes fluctuated at around 0.7 mA/cm^2 for 20 h,with an initial current density 0.75 mA/cm^2.The improvement in field emission properties was found to be due to the exposure of more CNT tips,the wider gaps among the CNTs and the infiltration of nickel particles.

FePO4-coated Li[Li0.2Ni0.13Co0.13Mn0.54]O2 with improved cycling performance as cathode material for Li-ion batteries

Li[Li0.2Ni0.13Coo.13Mn0.54]O2 cathode materials were synthesized by carbonate-based co-precipitation method, and then, its surface was coated by thin layers of FePO4. The prepared samples were characterized by X-ray diffraction （XRD）, field emission scanning electron micro- scope （FESEM）, energy-dispersive spectroscopy （EDS）, and transmission electron microscopy （TEM）. The XRD and TEM results suggest that both the pristine and the coated materials have a hexagonal layered structure, and the FePO4 coating layer does not make any major change in the crystal structure. The FePO4-coated sample exhibits both improved initial discharge capacity and columbic efficiency compared to the pristine one. More significantly, the FePO4 coating layer has a much positive influence on the cycling perfor- mance. The FePO4-coated sample exhibits capacity reten- tion of 82 % after 100 cycles at 0.5℃ between 2.0 and 4.8 V, while only 28 % for the pristine one at the same charge-discharge condition. The electrochemical impe- dance spectroscopy （EIS） results indicate that this improved cycling performance could be ascribed to the presence of FePO4 on the surface of Li[Li0.2Ni0.13Co0.13Mno.54102 par- ticle, which helps to protect the cathode from chemical attacks by HF and thus suppresses the large increase in charge transfer resistance.

Transmission-mode GaN photocathode based on graded Al_xGa_(1-x)N buffer layer

We create a GaN photocathode based on graded AlxGa1-xN buffer layers to overcome the influence of buffer-emission layer interface on the photoemission of transmission-mode GaN photocathodes. A gate- shaped spectral response with a 260-nm starting wavelength and a 375-nm cut-off wavelength is obtained. Average quantum efficiency is 15% and short wavelength responses are almost equivalent to long wavelength ones. The fitted interface recombination velocity is 5×10^4 cm/s, with negligible magnitude, proving that the design of the graded buffer layers is efficient in obtaining good interface quality between the buffer and the emission laver.