Study of fault configuration related mysteries through multi seismic attribute analysis technique in Zamzama gas field area,southern Indus Basin,Pakistan

Seismic attribute analysis approach has been applied for the interpretation and identification of fault geometry of Zamzama Gas Field. Zamzama gas field area, which lies in the vicinity of Kirthar fold and thrust belt, Southern Indus Basin of Pakistan. The Zamzama fault and its related structure have been predicted by applying the Average Energy Attribute, Instantaneous Frequency Attribute, relative Acoustic Impedance Attribute and Chaotic Reflection Attribute on the seismic line GHPK98 A.34. The results have been confirmed by applying the spectral decomposition attribute on the same seismic line that reveal the geometric configuration of Zamzama structure. The fault is reverse and started from 0 s and ended at the depth of 2.5 s on the vertical seismic section. Hanging wall moves up along the fault plane under the action of eastward oriented stress, which formed a large northesouth oriented and eastward verging thrusted anticline.

Daily Variation of Natural Emission of Methane to the Atmosphere and Source Identification in the Luntai Fault Region of the Yakela Condensed Oil/Gas Field in the Tarim Basin,Xinjiang,China

The static flux chamber method was applied to study natural emissions of methane to the atmosphere in the Luntai fault region of Yakela Condensed Oil/Gas Field in the Tarim Basin, Xinjiang Municipality, northwestern China. Using an online method, which couples together a gas chromatography/high-temperature conversion/isotope ratio mass spectrometry （GC/C/MS）, 13^C/12^C ratios of methane in flux chambers were measured and showed that methane gases are liable to migrate from deep oil/gas reservoirs to the surface through fault regions and that a part of the migrated methane, which remains unoxidized can be emitted into the atmosphere. Methane emission rates were found to be highest in the mornings, lowest in the afternoons and then increase gradually in the evenings. Methane emission rates varied dramatically in different locations in the fault region. The highest methane emission rate was 10.96 mg/m^2·d, the lowest 4.38 mg/m^2, and the average 7.55 mg/ m^2·d. The 13^C/12^C ratios of the methane in the flux chambers became heavier as the enclosed methane concentrations increased gradually, which reveals that methane released from the fault region might come from thermogenic methane of the deep condensed oil/gas reservoir.

Deformation field around a thrust fault:A comparison between laboratory results and GPS observations of the 2008 Wenchuan earthquake

On May 12,2008,an Mw7.9 earthquake occurred in Wenchuan County,Sichuan Province,China.Movement of Yingxiu–Beichuan Fault in the Longmenshan Fault Zone was considered to be the main cause of the earthquake.Earthquakes are closely related to fault activities.Therefore,studying the strain distribution and evolution process around active fault zones is important to the understanding of seismic activities.In this study,we conduct laboratory experiments with uniaxial compression applied to marble sheets with intentionally fabricated cracks.The speckle patterns of the rock samples under different loading conditions are recorded in real time by a digital camera.To calculate the deformation fields of the deliberately cracked marble sheets during different stages of the loading processes,the recorded images are processed by the digital image correlation method.The distribution and variation of the displacement and strain are further analyzed in order to understand the strain localization of and observed damage in the experimental fracture zones.Finally,we compare these laboratory results with the GPS-observed coseismic displacements during the 2008 Wenchuan earthquake,to assess the consistency between our laboratory observations and the field observations of the earthquake,but also to suggest how laboratory results can improve thinking about how earthquake patterns do and do not reflect fault patterns.

Effects of fault movement and material properties on deformation and stress fields of Tibetan Plateau

We compare the factors which affect the movement of Tibetan Plateau by building three types of finite element models： an elastic materials （M-EC）, a continuous model composed by non-linear materials （M-PC）, and an elastic model with discontinuous fault movements （M-ET）. Both in M-ET and M-EC, the materials in Qiangtang and Lhasa block are elastic, and in M-ET, discontinuous movement of faults is considered for evaluating the effects of strike-slip faults. In model M-PC Druker-Prager plastic materials are used in Qiangtang and Lhasa block. Comparisons of the numerical simulation and the GPS observations show following characteristics： （1） Under present tectonic environment, short-term deformation of Tibetan Plateau can be simulated well by elastic models; （2） Discontinuous fault activities increase the lateral extrusion of the eastern part of Tibetan Plateau, reduce the stress field level in Qiangtang, Tarim and Qaidam blocks and strengthen the E-W extensional force in the east and the west parts of Qiangtang block; （3） Properties of plastic materials reduce the total stress field and the E-W extensional force, thus, the normal fault earthquakes in southern Tibet is mainly owed to the effect of active fault movement. Based on the numerical simulations we speculate that faults movement may play a more important role on the kinematic pattern of Tibetan Plateau than bulk properties.

Determine Stress Field of the Shirband Area by Geometric and Kinematic Analysis of Faults and Folds (North Damqan, Iran)

In this paper faults and folds of shirband area (north of damqan) investigated to determine the orient of the stress field. The study area is limited between the two faults with E-W strike and northward slip. Investigations result show major faults of the area have sinisteral mechanism. Waterways displacement and slicken slip of faults approve this issue. Three main folds of area has approx-imately same trend along major faults (E-W). Orientation of stress field investigated and classified by using from some large and medium scale faults and folds. Analysis of stress field investigated by inversion method show that compression axis in the study area have approximately NE-SW strike.

Characteristics of the seismic source stress field in the joint region of Xianshuihe, Longmenshan and An(ninghe faults

Twenty-two earthquakes (ML=2.2-3.7) in the joint region of Xianshuihe, Longmenshan and An'ninghe faults are studied in this paper. The source mechanism solutions of these events are obtained using P-wave first motion method, and the characteristics of the source stress field and rupture in the joint region are summarized preliminarily with some results of other researchers. Being strongly extruded by the approximately horizontal regional stress with the direction from north-west to south-east and the effect of the complex tectonics in the region, the source stress field has complex and variable characteristics. The earthquakes mainly show normal or strike-slip faults in Yajiang, North-triangle and west of Chengdu-block areas, indicating that the vertical forces have been playing an important role in the source stress fields, while the earthquakes mainly show reverse or strike-slip faults in Baoxing-Tianquan area, with the horizontal components of the principal pressure stress axes identical to the south-west direction to which the shallow mass is moving. We think that the manifold combinations of earthquake faults are the micro-mechanism based upon which the large regional shallow crust mass has been moving continually.

The stress field variation caused by faulting and the prediction for seismic risk

The stress field caused by faulting has an effect on the stability of the neighboring faults, and the study on the fault interaction has a close relation with the prediction of seismic risk. Stress field caused by the rectangle fault in the semi-infinite elastic medium is calculated on the basis of the elastic dislocation theory. The result shows that most of the successive large earthquakes, in the southwestern part of China and North China, occurred in the increasing area of shear stress S(xy) and the decreasing area of normal stress S(yy) The increasing of earthquake occurrence probability has a function relation with the increasing of stress. Earthquake triggering is resulted from the increasing of shear stress and the decreasing of normal stress. An activation coefficient A, of the earthquake is defined to express the change of seismic activity. The concrete risk region can be obtained through space scanning of At value. Finally, the fault interaction in a large scope is discussed in this paper.

Modifications in the Stress Field of a Long Inclined Fault Caused by the Welded-Contact Boundary Conditions across the Interface between Two Elastic Half-Spaces

In welded-contact boundary conditions, some stress components are not required to be continuous across the boundary between two elastic half-spaces. The purpose of this note is to study the modifications in the stress field of a long inclined strike-slip, dip-slip or tensile fault caused by the welded-contact boundary conditions across the interface between two elastic half-spaces. The Poisson’s ratios of the two half-spaces do not appear in the stress field of a strike-slip fault. In the case of a dip-slip fault, the Poisson’s ratio of the half-space in which the fault lies, has a significant influence on the stress field across the interface. However, for a tensile fault, the modification in the stress field is significantly affected by the Poisson’s ratios of both the half-spaces.

Development of Magnetic Field Sensor and Motor Fault Monitoring Application

For the purpose of motor fault real-time monitoring, this research developed a nano-silicon ni- tride film based magnetic field (MF) sensor, and applied this sensor in MF detection of two common faults. Through experiment, it turned out that arc discharge and slot discharge occur in motor fault produce MF with certain laws. This result proved the feasibility of the sensor and sensing method in MF analysis, and revealed possibility of a new method in fault detection.

Numerical modeling of tectonic stress field and fault activity in North China

On the basis of a 3-dimension visco-elastic finite element model of lithosphere in North China, we numerically simulate the recent mutative figures of tectonic stress field. Annual change characteristics of stress field are： 1 ） Maximum principal tensile stress is about 3 -9 kPaa-1 and its azimuth lie in NNW-SSE. 2） Maximum principal compressive stress is about 1 - 6 kPaa-1 and its azimuth lie in NEE-SWW. 3 ） Maximum principal tensile stress is higher both in the west region and Liaoning Province. 4） Variation of tectonic stress field benefits fault movement in the west part and northeast part of North China. 5 ）Annual accumulative rates of Coulomb fracture stress in Tanlu fault belt have segmentation patterns： Jiashan-Guangji segment is the high- est （6 kPaa - 1 ） , Anshan-Liaodongwan segment is the second （5 kPaa - l ） , and others are relatively lower （ 3 - 4 kPaa-1 ）.

Fault Prediction and Diagnosis of Warship Equipment Field Programmable Gate Array Software

In order to solve the current high failure rate of warship equipment field programmable gate array( FPGA) software,fault detection is not timely enough and FPGA detection equipment is expensive and so on. After in-depth research,this paper proposes a warship equipment FPGA software based on Xilinx integrated development environment( ISE) and ModelSim software.Functional simulation and timing simulation to verify the correctness of the logic design of the FPGA,this method is very convenient to view the signal waveform inside the FPGA program to help FPGA test engineers to achieve FPGA fault prediction and diagnosis. This test method has important engineering significance for the upgrading of warship equipment.

Active Faulting Pattern,Present-day Tectonic Stress Field and Block Kinematics in the East Tibetan Plateau

This paper examines major active faults and the present-day tectonic stress field in the East Tibetan Plateau by integrating available data from published literature and proposes a block kinematics model of the region. It shows that the East Tibetan Plateau is dominated by strike-slip and reverse faulting stress regimes and that the maximum horizontal stress is roughly consistent with the contemporary velocity field, except for the west Qinling range where it parallels the striking of the major strike-slip faults. Active tectonics in the East Tibetan Plateau is characterized by three faulting systems. The left-slip Kunlun-Qinling faulting system combines the east Kunlun fault zone, sinistral oblique reverse faults along the Minshan range and two major NEE-striking faults cutting the west Qinling range, which accommodates eastward motion, at 10--14 mm/a, of the Chuan-Qing block. The left-slip Xianshuihe faulting system accommodated clockwise rotation of the Chuan-Dian block. The Longmenshan thrust faulting system forms the eastern margin of the East Tibetan Plateau and has been propagated to the SW of the Sichuan basin. Crustal shortening across the Longmenshan range seems low （2-4 mm/a） and absorbed only a small part of the eastward motion of the Chuan-Qing block. Most of this eastward motion has been transmitted to South China, which is moving SEE-ward at 7-9 mm/a. It is suggested from geophysical data interpretation that the crust and lithosphere of the East Tibetan Plateau is considerably thickened and theologically layered. The upper crust seems to be decoupled from the lower crust through a decollement zone at a depth of 15-20 kin, which involved the Longmenshan fault belt and propagated eastward to the SW of the Sichuan basin. The Wenchuan earthquake was just formed at the bifurcated point of this decollement system. A rheological boundary should exist beneath the Longmenshan fault belt where the lower crust of the East Tibetan Plateau and the lithospheric mantle of the Yangze block are juxtaposed.

Fault slip and modern tectonic stress field in and around Kunming basin

Kunming basin is a Cenozoic faulted basin under the control of mainly SN-trending active faults. In and around the basin, there are a total of eight major active faults. Seismo-geological survey and fault slip observation show that the SN- and NE-trending active faults are mostly sinistral strike-slip faults, while the NW-trending faults are mostly dextral strike-slip faults. Using stress tensor inversion method with 706 active fault striation data at 22 measurement sites, we determined tectonic stress field of the study area. The result shows that modern tectonic stress field in and around Kunming basin is characterized by NNW-SSE compression, ENE-WSW extension, and strike-slip stress regimes. The maximum principal compressional stress （σ1） is oriented 335o;o, with an average dip angle of 21°; the minimum （σ3） is oriented 44o;3o, with an average dip angle of 14°, and the intermediate （σ2） has a high, or nearly vertical, dip angle. The inversion result from fault slip data is consistent with the result from focal mechanism solutions.

The seismicity and tectonic stress field characteristics of the Longmenshan fault zone before the Wenchuan M_S8.0 earthquake

The seismicity of Longrnenshan fault zone and its vicinities before the 12 May 2008 Wenchuan Ms8.0 earthquake is studied. Based on the digital seismic waveform data observed from regional seismic networks and mobile stations, the focal mechanism solutions are determined. Our analysis results show that the seismicities of Longmenshan fault zone before the 12 May 2008 Wenchuan earthquake were in stable state. No obvious phenomena of seismic activity intensifying appeared. According to focal mechanism solutions of some small earthquakes before the 12 May 2008 Wenchuan earthquake, the direction of principal compressive stress P-axis is WNW-ESE. The two hypocenter fault planes are NE-striking and NW-striking. The plane of NE direction is among N50°-70°E, the dip angles of fault planes are 60°-70° and it is very steep. The faultings of most earthquakes are dominantly characterized by dip-slip reverse and small part of faultings present strike-slip. The azimuths of principal compressive stress, the strikes of source fault planes and the dislocation types calculated from some small earthquakes before the 12 May 2008 Wenchuan earthquake are in accordance with that of the main shock. The average stress field of micro-rupture along the Longmenshan fault zone before the great earthquake is also consistent with that calculated from main shock. Zipingpu dam is located in the east side 20 km from the initial rupture area of the 12 May 2008 Wenchuan earthquake. The activity increment of small earthquakes in the Zipingpu dam is in the period of water discharging. The source parameter results of the small earthquakes which occurred near the initial rupture area of the 12 May 2008 Wenchuan earthquake indicate that the focal depths are 5 to 14 km and the source parameters are identical with that of earthquake.

Evolution of 3D tectonic stress field and fault movement in North China

Based on data of fault movement surveying, we simulate the evolution process of three dimensional stress field in North China by three dimensional finite element method. Evolutional patterns in one-year time scale from 1986 to 1997 have been illustrated and the evolution characteristics of stress field have been analyzed. In comparison with the seismic activity among that time interval in North China, we have primarily discussed the relationship between the evolution of stress field and seismic activity.

Far-field analysis of effects of unilateral rupturing fault on the space correlation of strong ground motion

On the assumption that seismic source is simplified as linear rupture fault with finite length, this paper qualitatively studies the seismic source effects on space correlation of strong ground motion. Based on expanding expression of Fourier spectrum of strong ground motion with space coordinate variables, this paper also gives a expression of describing correlation of strong ground motion field. According to far-field condition, the theoretical formula of the expression can be obtained. Furthermore, this paper presents a theoretical formula of estimation the radius of strong ground motion field, which depends on expansion condition of Fourier spectrum of strong ground motion, with space variables. At last, taking one earthquake as an example, this paper gives three-dimension patterns of radius of the field with epicenter distance and azimuth as well as frequency.

Prediction of near-field strong ground motions for scenario earthquakes on active fault

A method to predict near-field strong ground motions for scenario earthquakes on active faults is proposed. First, macro-source parameters characterizing the entire source area, i.e., global source parameters, including fault length, fault width, rupture area, average slip on the fault plane, etc., are estimated by seismogeology survey, seismicity and seismic scaling laws. Second, slip distributions characterizing heterogeneity or roughness on the fault plane, i.e., local source parameters, are reproduced/evaluated by the hybrid slip model. Finally, the finite fault source model, developed from both the global and local source parameters, is combined with the stochastically synthetic technique of ground motion using the dynamic comer frequency based on seismology. The proposed method is applied to simulate the acceleration time histories on three base-rock stations during the 1994 Northridge earthquake. Comparisons between the predicted and recorded acceleration time histories show that the method is feasible and practicable.

3-D finite element modeling for evolution of stress field and interaction among strong earthquakes in Sichuan-Yunnan region

Based on the latest achievement about activities of geological structure, a 3-D finite-element model containing four layers of upper crust, lower crust (two layers) and upper mantle is established in the paper. By repeated tests and revisions, the boundary conditions of the model are determined. And then the background stress field, the stress field caused by fault creep and the stress field triggered by strong earthquake in Sichuan-Yunnan region, as well as their dynamic variations are calculated. The results indicate that the latter earthquake often occurs in the area with positive Coulomb rupture stress change associated with the former one, the former earthquake has a triggering effect on the latter one to a certain extent, and strong earthquake often occur in groups under the background of high stress, which is of great significance for distinguishing seismic anomalies, as well as for improving the level of earthquake prediction.

Fault plane parameters of Sanhe-Pinggu M8 earthquake in 1679 determined using present-day small earthquakes

The great Sanhe-Pinggu M8 earthquake occurred in 1679 was the largest surface rupture event recorded in history in the northern part of North China plain. This study determines the fault geometry of this earthquake by inverting seismological data of present-day moderate-small earthquakes in the focal area. We relocated those earthquakes with the double-difference method. Based on the assumption that clustered small earthquakes often occur in the vicinity of fault plane of large earthquake, and referring to the morphology of the long axis of the isoseismal line obtained by the predecessors, we selected a strip-shaped zone from the relocated earthquake catalog in the period from 1980 to 2009 to invert fault plane parameters of this earthquake. The inversion results are as follows： the strike is 38.23°, the dip angle is 82.54°, the slip angle is -156.08°, the fault length is about 80 km, the lower-boundary depth is about 23 km and the buried depth of upper boundary is about 3 kin. This shows that the seismogenic fault is a NNE-trending normal dip-slip fault, southeast wall downward and northwest wall uplift, with the right-lateral strike-slip component. Moreover, the surface rupture zone, intensity distribution of the earth-quake and seismic-wave velocity profile in the focal area all verified our study result.

A quantitative research for present-time crustal motion in Fujian Province, China and its marginal sea── Synthetical analysis of GPS measurement, fault deformation survey, leveling and focal mechanism solution

Based on the Chinese mainland GPS network (1994~1996), Fujian GPS network (1995~1997), cross fault deformation network (1982-1998), precise leveling network (1973~1980) and focal mechanism solutions of the recent several tens years, we synthetically and quantitatively studied the present-time crustal motion of the southeast coast of Chinese mainland-Fujian and its marginal sea. We find that this area with its mainland together moves toward SE with a rather constant velocity of 11 .2±3.0 mm/a. At the same time, there is a motion from the Quanzhou bay pointing to hinterland, with a major orientation of NW, extending toward two sides, and with an average velocity of 3.0±2.6 mm/a. The faults orienting NE show compressing motions, and the ones orienting NW show extending motions. The present-time strain field derived from crustal deformation is consistent with seismic stress field derived from the focal mechanism solutions and the tectonic stress field derived from geology data. The principal stress of compression orients NW (NWW) - SE (SEE). Demarcated by the NW orienting faults of the Quanzhou bay and Jinjiang-Yongan, the crustal motions show regional characteristics f the southwest of Fujian and the boundary of Fujian and Guangdong are areas of rising, the northeast of Fujian are areas of sinking. The horizontal strain rate and the fault motion of the former are both greater than the later. The side-transferring motion of Hymalaya collision zone and the compression of the west pacific subduction zone affect the motion of the research area. The amount of motion affected by the former is larger than the later, but the former is homogeneous and the later is not, which indicates that the events of strong earthquakes in this region relate more directly with western pacific subduction zone.