A New Design Method for Variable Digital Filter Based on Field Programmable Gate Array(FPGA)

In order to obtain variable characteristics,the digital filter's type,number of taps and coefficients should be changed constantly such that the desired frequency-domain characteristics can be obtained.This paper proposes a method for self-programmable variable digital filter(VDF) design based on field programmable gate array(FPGA).We implement a digital filter system by using custom embedded micro-processor,programmable finite impulse response(P-FIR) macro module,coefficient-loader,clock manager and analog/digital(A/D) or digital/analog(D/A) controller and other modules.The self-programmable VDF can provide the best solution for realization of digital filter algorithms,which are the low-pass,high-pass,band-pass and band-stop filter algorithms with variable frequency domain characteristics.The design examples with minimum 1 to maximum 32 taps FIR filter,based on Modelsim post-routed simulation and onboard running on XUPV5-LX110T,are provided to demonstrate the effectiveness of the proposed method.

Synthesis of Nonlinear Control of Switching Topologies of Buck-Boost Converter Using Fuzzy Logic on Field Programmable Gate Array (FPGA)

An intelligent fuzzy logic inference pipeline for the control of a dc-dc buck-boost converter was designed and built using a semi-custom VLSI chip. The fuzzy linguistics describing the switching topologies of the converter was mapped into a look-up table that was synthesized into a set of Boolean equations. A VLSI chip–a field programmable gate array (FPGA) was used to implement the Boolean equations. Features include the size of RAM chip independent of number of rules in the knowledge base, on-chip fuzzification and defuzzification, faster response with speeds over giga fuzzy logic inferences per sec (FLIPS), and an inexpensive VLSI chip. The key application areas are: 1) on-chip integrated controllers;and 2) on-chip co-integration for entire system of sensors, circuits, controllers, and detectors for building complete instrument systems.

Fault Prediction and Diagnosis of Warship Equipment Field Programmable Gate Array Software

In order to solve the current high failure rate of warship equipment field programmable gate array( FPGA) software,fault detection is not timely enough and FPGA detection equipment is expensive and so on. After in-depth research,this paper proposes a warship equipment FPGA software based on Xilinx integrated development environment( ISE) and ModelSim software.Functional simulation and timing simulation to verify the correctness of the logic design of the FPGA,this method is very convenient to view the signal waveform inside the FPGA program to help FPGA test engineers to achieve FPGA fault prediction and diagnosis. This test method has important engineering significance for the upgrading of warship equipment.

MIXED-GRAINED CMOS FIELD PROGRAMMABLE ANALOG ARRAY FOR SMART SENSORY APPLICATIONS

The drive towards shorter design cycles for analog integrated circuits has given impetus to the development of Field Programmable Analog Arrays(FPAAs),which are the analogue counterparts of Field Programmable Gate Arrays(FPGAs).In this paper,we present a new design methodology which using FPAA as a powerful analog front-end processing platform in the smart sensory microsystem.The proposed FPAA contains 16 homogeneous mixed-grained Configurable Analog Blocks(CABs) which house a variety of processing elements especially the proposed fine-grained Core Configurable Amplifiers(CCAs).The high flexible CABs allow the FPAA operating in both continuous-time and discrete-time approaches suitable to support variety of sensors.To reduce the nonideal parasitic effects and save area,the fat-tree interconnection network is adopted in this FPAA.The functionality of this FPAA is demonstrated through embedding of voltage and capacitive sensor signal readout circuits and a configurable band pass filter.The minimal detectable voltage and capacitor achieves 38 uV and 8.3 aF respectively within 100 Hz sensor bandwidth.The power consumption comparison of CCA in three applications shows that the FPAA has high power efficiency.And the simulation results also show that the FPAA has good tolerance with wide PVT variations.

应答器上行链路信号自适应解调方法的FPGA实现

为降低电磁干扰对信号传输的影响,分析了应答器上行链路信号传输过程及其易遭受干扰信号的特点,设计了基于符号最小均方误差(least mean square,LMS)算法的自适应解调方法。为在硬件平台中实现该解调方法,通过仿真计算,确定LMS算法的自适应算法中间变量变化范围,使用截位操作完成权值系数的更新,设置均衡器长度、步长因子、中值滤波系数分别为1、1/64、16,可在不占用过多硬件资源情况下获得良好的解调性能。解调算法在现场可编程门阵列(field programmable gata array,FPGA)上予以验证,实验表明,当信噪比为6 dB时,FPGA中自适应解调误码率为0.000001,在信噪比大于等于6 dB时,实测误码率与仿真分析误码率基本一致;FPGA自适应解调方法在列车不同速度等级下误码率均小于10^(-6)。

FPGA-Based Efficient Programmable Polyphase FIR Filter

The modelling, design and implementation of a high-speed programmable polyphase finite impulse response (FIR) filter with field programmable gate array (FPGA) technology are described. This FIR filter can run automatically according to the programmable configuration word including symmetry/asymmetry, odd/even taps, from 32 taps up to 256 taps. The filter with 12 bit signal and 12 bit coefficient word-length has been realized on a Xilinx VirtexⅡ-v1500 device and operates at the maximum sampling frequency of (160 MHz.)

Machine learning algorithm partially reconfigured on FPGA for an image edge detection system

Unmanned aerial vehicles(UAVs)have been widely used in military,medical,wireless communications,aerial surveillance,etc.One key topic involving UAVs is pose estimation in autonomous navigation.A standard procedure for this process is to combine inertial navigation system sensor information with the global navigation satellite system(GNSS)signal.However,some factors can interfere with the GNSS signal,such as ionospheric scintillation,jamming,or spoofing.One alternative method to avoid using the GNSS signal is to apply an image processing approach by matching UAV images with georeferenced images.But a high effort is required for image edge extraction.Here a support vector regression(SVR)model is proposed to reduce this computational load and processing time.The dynamic partial reconfiguration(DPR)of part of the SVR datapath is implemented to accelerate the process,reduce the area,and analyze its granularity by increasing the grain size of the reconfigurable region.Results show that the implementation in hardware is 68 times faster than that in software.This architecture with DPR also facilitates the low power consumption of 4 mW,leading to a reduction of 57%than that without DPR.This is also the lowest power consumption in current machine learning hardware implementations.Besides,the circuitry area is 41 times smaller.SVR with Gaussian kernel shows a success rate of 99.18%and minimum square error of 0.0146 for testing with the planning trajectory.This system is useful for adaptive applications where the user/designer can modify/reconfigure the hardware layout during its application,thus contributing to lower power consumption,smaller hardware area,and shorter execution time.

GJB 5000B在FPGA工程中的应用分析

为引入软件工程化管理办法对设计开发实践实施管理,结合GJB 5000B体系要求,对现场可编程逻辑门阵列(Field Programmable Gate Array,FPGA)的设计开发流程和GJB 5000B的工程实践要求进行梳理、比对和分析,并提出一套FPGA开发管理在GJB 5000B推进实践中的实施办法。研究成果可为GJB 5000B在FPGA工程中的应用提供一定参考。

Design and verification of an FPGA programmable logic element based on Sense-Switch pFLASH

This paper proposes a kind of programmable logic element(PLE)based on Sense-Switch pFLASH technology.By programming Sense-Switch pFLASH,all three-bit look-up table(LUT3)functions,partial four-bit look-up table(LUT4)functions,latch functions,and d flip flop(DFF)with enable and reset functions can be realized.Because PLE uses a choice of operational logic(COOL)approach for the operation of logic functions,it allows any logic circuit to be implemented at any ratio of combinatorial logic to register.This intrinsic property makes it close to the basic application specific integrated circuit(ASIC)cell in terms of fine granularity,thus allowing ASIC-like cell-based mappers to apply all their optimization potential.By measuring Sense-Switch pFLASH and PLE circuits,the results show that the“on”state driving current of the Sense-Switch pFLASH is about 245.52μA,and that the“off”state leakage current is about 0.1 pA.The programmable function of PLE works normally.The delay of the typical combinatorial logic operation AND3 is 0.69 ns,and the delay of the sequential logic operation DFF is 0.65 ns,both of which meet the requirements of the design technical index.

基于DSP与FPGA的变流器通用控制平台研究

提出一种基于DSP和现场可编程门阵列(FPGA)双CPU结构的新型变流器控制系统方案,其中DSP完成变流器控制策略的实现,主要包括:最大功率点跟踪、电压电流双闭环控制、低电压穿越控制、通信功能;FPGA完成三相锁相环控制、AD芯片采样控制、SVPWM波形控制、逻辑输出控制以及各类故障信号检测与停机保护功能,并采用了基于WIFI模块的风电故障信息传输系统。以双馈风电变流器为模型,设计了双馈风力发电变流器系统,完成了两电平与三电平SVPWM控制算法的FPGA实现。最后在自主研发的1.5 MW,2 MW双馈式变流器样机与光伏逆变器样机上进行了大量实验和长期的现场试运行,验证了控制系统平台的可行性与实用性。

SRAM型FPGA单粒子辐照试验系统技术研究

单粒子辐射效应严重制约FPGA的空间应用,为提高FPGA在辐射环境中的可靠性,深入研究抗辐射加固FPGA单粒子效应评估方法,设计优化单粒子效应评估方案,开发相应的评估系统,提出基于SRAM时序修正的码流存储比较技术和基于SelectMAP端口配置回读技术。借助国内高能量大注量率的辐照试验环境,完成FPGA单粒子翻转(SEU)、单粒子闩锁(SEL)和单粒子功能中断(SEFI)等单粒子效应的检测,试验结果表明,该方法可以科学有效地对SRAM型FPGA抗单粒子辐射性能进行评估。

FPGA的室内空气质量检测与调节系统

提出了一种基于现场可编程门阵列(FPGA)的无线室内空气质量检测与调节系统设计方法,并对数据采集、蓝牙通信、步进电机驱动控制原理和系统方案进行了全面分析。实验结果证明:系统实现了对室内温度等质量信息的采集、LCD显示、通信、上位机远程调节处理等功能,保证了室内空气质量检测数据的实时性、可靠性。系统适用于智能、绿色家居,以及蔬菜种植大棚等需要对空气质量进行评价的场所。

阻塞斩波三相交交变频电源的FPGA控制实现

变频技术是重要的节能技术,所以针对低频或转速不恒定的节能设备,提出了基于FPGA数字控制的三相交交直接变频电源技术。用VHDL语言对主控芯片FPGA编写程序,其输出的高频SPWM信号经驱动电路后作为电源和负载间开关MOSFET的控制信号。MOSFET周期性地部分阻塞电源不能达到负载来改变输出电压的频率,同时在放行的时区斩波来改变输出电压的幅值。基于Matlab仿真平台,对系统进行了建模和仿真,仿真结果验证了该技术的正确性。最后给出了频率为7.14 Hz和2.63 Hz的实验波形,实验结果证明了该技术的可行性。

电力线载波通信定时同步算法及其FPGA实现

基于电力线载波通信G3技术标准下的物理层协议,针对电力线上噪声干扰较大,造成帧同步有虚警现象,符号定时同步尖峰幅值随信号衰减变化以及尖峰的旁瓣超过门限等缺点,提出了准确性更高、占用硬件资源相对较少的电力线载波通信帧同步与符号定时算法。通过算法仿真,表明该算法在信噪比较低时,具有门限自适应性,能够克服旁瓣的干扰,并易于硬件实现的特点。在一发一收两块现场可编程门阵列(FPGA)开发板上验证,提出新的帧同步、符号定时算法和硬件实现方案,实现了对电力线载波通信的正交频分复用(OFDM)基带系统进行实时、连续、准确的定时同步。

基于FPGA的正交数控振荡器(NCO)的设计与实现

在研究数控振荡器NCO工作原理的基础上,通过分析对比几种不同的NCO设计方法,采用了算法简单、节省资源的基于ROM查找表的设计方法。针对正交数控振荡器NCO的主要部件正余弦存储表、可变模计数器进行了算法设计和电路设计,并在Altera公司的FPGA上进行了验证,波形仿真结果表明了电路设计的正确性。采用查找表的方法可以有效提高系统功能的可扩展性和系统的可集成性,使得NCO功能模块可以通过配置存储表、频率控制字来满足多种应用场合下的NCO设计需要,可以广泛地应用于各种现代通信系统中。

基于FPGA的连续相位π/4DQPSK调制器和解调器

以FPGA器件为核心设计连续相位π/4DQPSK的调制器和解调器 ,将绝大部分功能模块由大规模FPGA内部资源来实现 ,这样既可以提高通信系统的稳定性和灵活性 ,又便于系统的集成化和小型化 .由于连续相位π/4DQPSK调制独特的相位变化 ,调制器中采用了双通道设计 ,成功实现了过渡区相位与主要区间相位的交替产生 .解调器中利用计数器控制抽样时刻 ,保证抽取出的信号值处于码元的主要区间 .

基于FPGA的车辆振动信号提取方法

为了从车辆复杂噪声背景中实时提取陀螺仪的有效振动信号,在分析弱信号特征提取方法的基础上,针对自适应滤波算法处理相关信号时收敛速度降低的缺点,提出一种适用于FPGA(Field Programmable Gata Ar-ray)的自适应步长LMS(Least Mean Square)算法。该算法通过建立步长和误差信号相关值之间的非线性关系,使步长仅与输入有用信号相关,降低算法对噪声的敏感度。实验以收敛速度和计算复杂度两个指标对该算法与其他改进算法进行比较,并以真实车辆振动信号提取结果分析验证该算法对车载环境噪声和陀螺仪自身噪声都有较好抑制。在用算法计算基础上,以FPGA平台提出并实现一种可扩展滤波器结构。设计采用一阶滤波单元重用方式完成多阶累加计算,在目前最大规模FPGA芯片上实现8～256阶滤波器。实验表明,该设计充分利用芯片内逻辑资源,处理速度快,可靠性高,并适用于车辆中低速行驶姿态测量系统。

10 Gbit/s PRBS tester implemented in FPGA

The design of an FPGA（ field programmable gate array） based programmable SONET （synchronous optical network） OC-192 10 Gbit/s PRBS （pseudo-random binary sequence） generator and a bit interleaved polarity 8 （BIP-8） error detector is presented. Implemented in a parallel feedback configuration, this tester features PRBS generation of sequences with bit lengths of 2^7 - 1,2^10- 1,2^15 - 1,2^23 - land 2^31 - 1 for up to 10 Gbit/s applications with a 10 Gbit/s optical transceiver, via the SFI-4 （OC-192 serdes-framer interface）. In the OC-192 frame alignment circuit, a dichotomy search algorithm logic which performs the functions of word alignment and STM-64/OC192 de-frame speeds up the frame sync logic and reduces circuit complexity greatly. The system can be used as a low cost tester to evaluate the performance of OC-192 devices and components, taking the replacement of precious commercial PRBS testers.

Design of IP core for IIC bus controller based on FPGA

The intellectual property （IP） core for inter-integrated circuit （IIC） bus controller is designed using finite state machine （FSM） based on field programmable gate array （FPGA）. Not only the data from AT 24C02C can be read automatically after power on, but also the data from upper computer can be written into AT24C02C immediately under the control of the IIC bus controller. When it is applied to blast wave overpressure test system, the IIC bus controller can read and store working parameters automatically. In a laboratory environment, the IP core simulation is carried out and the result is accurate. In the explosion field test, by analyzing the obtained valid data, it can be concluded that the designed IP core has good reliability.

基于FPGA和交流步进控制的永磁同步电机伺服系统

以永磁同步电机(PMSM)为控制对象,以现场可编程门阵列(FPGA)为控制核心器件,对交流步进控制方式应用于伺服系统的场合,进行了理论与仿真研究,最后经实际试验验证。仿真与试验结果表明,应用交流步进控制方式的PMSM伺服系统具有良好的速度与位置可控性,能够满足现代工业对伺服系统的高要求。同时,研究结果也为PMSM在高性能控制场合下的应用提供了参考。