Quantitative research of the liquid film characteristics in upward vertical gas, oil and water flows

The study of liquid film characteristics in multiphase flow is a very important research topic, however,the characteristics of the liquid film around Taylor bubble structure in gas, oil and water three-phase flow are not clear. In the present study, a novel liquid film sensor is applied to measure the distributed signals of the liquid film in three-phase flow. Based on the liquid film signals, the liquid film characteristics including the structural characteristics and the nonlinear dynamics characteristics in three-phase flows are investigated for the first time. The structural characteristics including the proportion, the appearance frequency and the thickness of the liquid film are obtained and the influences of the liquid and gas superficial velocities and the oil content on them are investigated. To investigate the nonlinear dynamics characteristics of the liquid film with the changing flow conditions, the entropy analysis is introduced to successfully uncover and quantify the dynamic complexity of the liquid film behavior.

Research on oil film characteristics of piston pair in swash plate axial piston pump

The research on the oil film characteristic of piston pair is beneficial to the design and optimization of friction pair,which can improve the performance of piston pump.The fluid pressure of piston cavity is accurately obtained by AMEsim simulation.Oil film thickness field model of piston pair under the slanting state of piston is established,and the distribution law is numerically analyzed under different speed and pressure by Matlab.The experiment model pump for oil film characteristic of piston pair is designed to measure oil film thickness under the pressure of 18 MPa.The experiment results show that oil film thickness varies greatly under high pressure,and oil film thickness fluctuates sharply under low speed.The minimum oil film thickness increases with spindle speed increasing and oil film characteristic of piston pair based on the numerical analysis method is verified.This method lays a foundation for studying the friction performance of piston pair in the axial piston pump.

Experimental Study on Wear Performance and Oil Film Characteristics of Surface Textured Cylinder Liner in Marine Diesel Engine

It is of a vital importance to reduce the frictional losses in marine diesel engines. Advanced surface textures have provided an e ective solution to friction performance of rubbing pairs due to the rapid development of surface engineering techniques. However,the mechanisms through which textured patterns and texturing methods prove beneficial remains unclear. To address this issue,the tribological system of the cylinder liner?piston ring(CLPR) is investigated in this work. Two types of surface textures(Micro concave,Micro V?groove) are processed on the cylinder specimen using di erent processing methods. Comparative study on the friction coe cients,worn surface texture features and oil film characteristics are performed. The results demonstrate that the processing method of surface texture a ect the performance of the CLPR pairs under the specific testing conditions. In addition the micro V?groove processed by CNCPM is more favorable for improving the wear performances at the low load,while the micro?con?cave processed by CE is more favorable for improving the wear performances at the high load. These findings are in helping to understand the e ect of surface texture on wear performance of CLPR.

Numerical investigation of film forming characteristics and mass transfer enhancement in horizontal polycondensation kettle

The process of producing high viscosity polyester by transesterification polycondensation needs to adjust the operating conditions and equipment structure of pre-polycondensation kettle and final polycondensation kettle to realize process intensification.In view of this,the fluid volume function method of computational fluid dynamics numerical simulation was used to investigate the film formation and surface renewal characteristics of horizontal polycondensation kettle under different operating conditions,including viscosity,rotating speed and liquid height.The results show that the viscosity and rotating speed were positively correlated with the film area and surface renewal in the pre-polycondensation stage.However,increasing the viscosity by several orders of magnitude in the final polycondensation kettle,the larger the film area and film thickness,but the overall surface renewal of the disk decreased.Therefore,a hexagonal hole disk is designed.By comparison,it is found that the film is more uniform,the surface update frequency is higher,and the power consumption can be reduced by more than 20%.

STATIONARY DYNAMIC CHARACTERISTICS ANALYSIS OF NEW SQUEEZED FILM DAMPER

Recur to multi-hole and better elastic characteristics of metal rubber （MR）, a new squeezed film damper with MR （SFD/MR） throttle ring installed on the end of MR and MR damping ring installed on the radial direction of MR is implemented. Based on the D＇alembert principle, a locomotion equation and the mathematical model of stationary response of SFD/MR system is put forward. It proves that the SFD/MR has better ability to resist unbalance loads than the traditional SFD after the stationary dynamic characteristics of the traditional SFD and the new SFD/MR are researched.

Microwave Characteristics of YBaCuO Film

The Research Center of Superconducting Materials of GRINM prepared a YBaCuOsuperconducting film with thickness of 500 nm, the microwave characterization of which was car-ried out at Microwave Center, Chengdu Electronics Science-technological University. The com-prehensive Microwave characteristics for large-area superconducting film is obtained firstly inChina. Using this film Microwave Center prepared a cavity, the quality factor Q of which attainedto the-state-of the-art (Q= 13100, at 79 K and 3.04 GHz).

Thermal Characteristics of PVA-PANI-ZnS Nanocomposite Film Synthesized by Gamma Irradiation Method

Gamma irradiation is employed for in situ preparation of PVA-PANI-ZnS nanocomposite. The irradiation dose is varied from 10 to 40 kGy at 10 kGy intervals. The XRD result confirms the formation of crystalline phases corresponding to ZnS nanoparticles, PVA and PANI. Field emission scanning electron microscopy shows the formation of agglomerated PANI along the PVA backbone, within which the ZnS nanoparticles are dispersed.UV-visible spectroscopy is conducted to measure the transmittance spectra of samples revealing the electronic absorption characteristics of ZnS and PANI nanoparticles. Photo-acoustic（PA） setup is installed to investigate the thermal properties of samples. The PA spectroscopy indicates a high value of thermal diffusivity for samples due to the presence of ZnS and PANI nanoparticles. Moreover, at higher doses, the more polymerization and formation of PANI and ZnS nanoparticles result in enhancement of thermal diffusivity.

Size Effect of Electromagnetic Constitutive Characteristics of Ultrathin Al Films

The ultrathin aluminum films with thickness in the range of 2～60 nm have been deposited by dc magnetron sputtering apparatus. Reflectance and transmittance of the obtained samples were measured with a WFZ-900-D4 UV/VIS spectrophotometer. The optical constant (n, k) and permittivity (ε', ε') were determined by applying Newton-Simpson recurrent substitution method. The results indicate that the electromagnetic constitutive characteristic of ultrathin aluminum films is a function of thickness and has obvious size effect.

Temperature Dependence of Electrical Characteristics in Indium-Zinc-Oxide Thin Film Transistors from 10 K to 400 K

The transfer characteristics of amorphous indium-zinc-oxide thin film transistors are measured in the temperature range of 10-400K. The variation of electrical parameters （threshold voltage, field effect mobility, sub-threshold swing, and leafage current） with decreasing temperature are then extracted and analyzed. Moreover, the dom- inated carrier transport mechanisms at different temperature regions are investigated. The experimental data show that the carrier transport mechanism may change from trap-limited conduction to variable range hopping conduction at lower temperature. Moreover, the field effect mobilities are also extracted and simulated at various temperatures.

Effects of Film Thickness and Ar/O2 Ratio on Resistive Switching Characteristics of HfOx-Based Resistive-Switching Random Access Memories

Cu/HfOx/n^＋Si devices are fabricated to investigate the influence of technological parameters including film thickness and Ar/02 ratio on the resistive switching （RS） characteristics of HfOx films, in terms of switch ratio, endurance properties, retention time and multilevel storage. It is revealed that the RS characteristics show strong dependence on technological parameters mainly by altering the defects （oxygen vacancies） in the film. The sample with thickness of 2Onto and Ar/O2 ratio of 12：3 exhibits the best RS behavior with the potential of multilevel storage. The conduction mechanism of all the films is interpreted based on the filamentary model.

Photocatalytic Property of TiO2 Films Deposited by Pulsed DC Magnetron Sputtering

TiO2 thin films were prepared by DC magnetron sputtering with the oxygen flow rate higher than the threshold. The film deposited for 5 h was of anatase phase with a preferred orientation along the <220> direction, but the films deposited for 2 and 3 h were amorphous. The transmittance and photocatalytic activity of the TiO2 films increased constantly with increasing film thickness. When the annealing temperature was lower than 700℃, only anatase grew in the TiO2 film. TiO2 phase changed from anatase to rutile when the annealing temperature was above 800℃. The photocatalytic activity decreased with increasing annealing temperature.

Optical super-resolution effect induced by nonlinear characteristics of graphene oxide films

In this work, we focus on the optical super-resolution effect induced by strong nonlinear saturation absorption(NSA) of graphene oxide(GO) membranes. The third-order optical nonlinearities are characterized by the canonical Z-scan technique under femtosecond laser(wavelength: 800 nm, pulse width: 100 fs) excitation. Through controlling the applied femtosecond laser energy, NSA of the GO films can be tuned continuously. The GO film is placed at the focal plane as a unique amplitude filter to improve the resolution of the focused field. A multi-layer system model is proposed to present the generation of a deep sub-wavelength spot associated with the nonlinearity of GO films. Moreover, the parameter conditions to achieve the best resolution(~λ/6) are determined entirely. The demonstrated results here are useful for high density optical recoding and storage, nanolithography, and super-resolution optical imaging.

The effect of annealing temperature and the characteristics of p-n junction diodes based on sprayed polyaniline/ZnO thin films

Polyaniline,ZnO and polyaniline/ZnO nanocomposite thin films are coated on glass substrates using the spray pyrolysis technique.The samples are characterized by the XRD,SEM,EDAX,UV-Vis and I-V characteristics. The XRD analyses confirm that the spray-coated polyaniline and ZnO thin films have orthorhombic and hexagonal structures,respectively,and optical bandgap energy decreases from 3.81 to 3.41 eV with the addition of a Zn atom.SEM analysis of the polyaniline/ZnO nanocomposite thin films shows that there is an agglomeration of ZnO particles with uniform distribution in the polyaniline matrix,and the diode characteristics of the polyaniline /ZnO nanocomposite show weak rectification behavior.Parameters such as the ideality factor,reverse saturation current and barrier height are calculated from the I-V characteristics.

A Hot Cracking Initiation Criterion Based on Solidification Liquid Film Characteristic and Microstructure

Herein,a hot cracking initiation criterion based on the characteristics of solidification liquid film and the microstructure was proposed,which integrated both the mechanical and non-mechanical factors during solidification.The criterion also took the effect of the shrinkage volume of the solid-liquid two-phase in the mushy zone,the flow behavior of the liquid film and the microstructure on the feeding behavior into account.Meanwhile,the effect factors of hot cracking initiation such as alloy composition,microstructure,mold design and process condition were included in this criterion,and it could quantitatively calculate whether hot cracks occurred under a certain state or not during solidification.The criterion was utilized to predict whether hot cracks occurred in Al-4.0 wt%Cu alloy in different initial solidification states or not,which was consistent with the experimental results and verified its reliability.According to the criterion expression,Vfeeding*was related with five effect factors includingη,ΔP*,l*,r*and n,in which r*and n were in positive correlation with Vfeeding*whileη,ΔP*and l*were in negative correlation with that,which provided a good instructive significance for mold design,process optimization and composition and microstructure regulation of alloys and simultaneously further enriched the mechanism and influencing factors of hot cracking initiation.Furthermore,a multiscale simulation method for calculating the characteristic parameters of hot tearing behavior during solidification was also provided in this study.

The Characteristic of Threading Dislocation in Different Structures GaN Films Grown by MOCVD

Three mechanisms to reduce threading dislocations(TDs) in GaN films as the epitaxial films grow thicker are suggested by SEM and