Air pressure law of a reservoir constructed in karst sinkholes

Karst sinkholes with natural negative landform provide favorable conditions for the pumped storage reservoir construction for less excavation work.However,the construction of the reservoir would plug the natural karst channels for water and air,which would cause remarkable air pressure in karst channels when the groundwater level fluctuates.A large laboratory simulation test was carried out to study the air pressure variation of a reservoir built on the karst sinkhole.The air pressure in the karst channel and inside the model was monitored during the groundwater rising and falling process.Result showed that the variation of air pressure in the karst channel and the surrounding rock exhibited a high degree of similarity.The air pressure increased rapidly at the initial stage of water level rising,followed by a slight decrease,then the air pressure increased sharply when the water level approached the top of the karst cave.The initial peak of air pressure and the final peak of air pressure were defined,and both air pressure peaks were linearly increasing with the water level rising rate.The negative air pressure was also analyzed during the drainage process,which was linearly correlated with the water level falling rate.The causes of air pressure variation in karst channels of a pumped storage reservoir built on the karst sinkhole were discussed.The initial rapid increase,then slight decrease and final sudden increase of air pressure were controlled by the combined effects of air compression in karst channel and air seepage into the surrounding rock.For the drainage process,the instant negative air pressure and gradual recovering of air pressure were controlled by the combined effects of negative air pressure induced by water level falling and air supply from surrounding rock.This work could provide valuable reference for the reservoir construction in karst area.

Cold atmospheric-pressure air plasma treatment of C6 glioma cells:effects of reactive oxygen species in the medium produced by the plasma on cell death

An atmospheric-pressure air plasma is employed to treat C6 glioma cells in vitro. To elucidate on the mechanism causing cell death and role of reactive species （RS） in the medium produced by the plasma, the concentration of the long-lived RS such as hydrogen peroxide, nitrate, and ozone in the plasma-treated liquid （phosphate-buffered saline solution） is measured. When vitamin C is added to the medium as a ROS quencher, the viability of C6 glioma cells after the plasma treatment is different from that without vitamin C. The results demonstrate that reactive oxygen species （ROS） such as H2O2, and O3 constitute the main factors for inactivation of C6 glioma cells and the reactive nitrogen species （RNS） may only play an auxiliary role in cell death.

A homogeneous atmospheric pressure air plasma in a 10 mm gap based on a three-electrode configuration

Generation of atmospheric pressure homogeneous air plasma in a large gap(>4 mm)is a challenge.In this study,an atmospheric pressure homogeneous air plasma generated in a gap up to 10 mm is reported,which is based on a three-electrode configuration,where a high-voltage(HV)electrode and a middle electrode form a surface dielectric barrier discharge(S-DBD),and together with the ground electrode form the main volume discharge.High-speed photographs confirm that the discharge in the main gap is homogeneous.The gas temperature of the plasma estimated from the N_(2)(C^(3)∏_(u)-B^(3)∏_(g))(Δv=-2)emission is about 320 K,which is close to room temperature.A detailed analysis shows that the discharge ignited between the HV electrode and the middle electrode is serving as an electron source,and the electrons deposited on the dielectric plate are due to the S-DBD along with the applied voltage generating a driving force,which results in a high concentration of seed electrons in the main gap and induces the homogeneous plasma.Further analysis shows that the electric field in the main gap is only about18.45 k V·cm^(-1),which is much lower than the typical breakdown electric field of 30 k V·cm^(-1)for atmospheric pressure air discharge.

Fluid-chemical modeling of the near-cathode sheath formation process in a high current broken in DC air circuit breaker

When the contacts of a medium-voltage DC air circuit breaker(DCCB) are separated, the energy distribution of the arc is determined by the formation process of the near-electrode sheath. Therefore, the voltage drop through the near-electrode sheath is an important means to build up the arc voltage, which directly determines the current-limiting performance of the DCCB. A numerical model to describe the near-electrode sheath formation process can provide insight into the physical mechanism of the arc formation, and thus provide a method for arc energy regulation. In this work, we establish a two-dimensional axisymmetric time-varying model of a medium-voltage DCCB arc when interrupted by high current based on a fluid-chemical model involving 16 kinds of species and 46 collision reactions. The transient distributions of electron number density, positive and negative ion number density, net space charge density, axial electric field, axial potential between electrodes, and near-cathode sheath are obtained from the numerical model. The computational results show that the electron density in the arc column increases, then decreases, and then stabilizes during the near-cathode sheath formation process, and the arc column's diameter gradually becomes wider. The 11.14 V–12.33 V drops along the17 μm space charge layer away from the cathode(65.5 k V/m–72.5 k V/m) when the current varies from 20 k A–80 k A.The homogeneous external magnetic field has little effect on the distribution of particles in the near-cathode sheath core,but the electron number density at the near-cathode sheath periphery can increase as the magnetic field increases and the homogeneous external magnetic field will lead to arc diffusion. The validity of the numerical model can be proven by comparison with the experiment.

Generation of Atmospheric Pressure Plasma by Repetitive Nanosecond Pulses in Air Using Water Electrodes

Dielectric barrier discharge （DBD） excitated by pulsed power is a promising method for producing nonthermal plasma at atmospheric pressure. Discharge characteristic in a DBD with salt water as electrodes by a home-made unipolar nanosecond-pulse power source is presented in this paper. The generator is capable of providing repetitive pulses with the voltage up to 30 kV and duration of 70 ns at a 300 Ω resistive load. Applied voltage and discharge current are measured under various experimental conditions. The DBD created between two liquid electrodes shows that the discharge is homogeneous and diffuse in the whole discharge regime, Spectra diagnosis is conducted by an optical emission spectroscopy. The air plasma has strong emission from nitrogen species below 400 nm, notably the nitrogen second positive system.

Surface Roughness Evaluation in Dry-Cutting of Magnesium Alloy by Air Pressure Coolant

In this paper, a studying of surface roughness in dry milling with air pressure coolant of wrought magnesium alloy AZ31B will be carried out. The effects of air flow, feed-rate per tooth, cutting velocity and number of inserts in a cutting tool on surface roughness have been examined. Surface roughness increases with increasing feed-rate per tooth and increasing number of inserts in the cutting tool. However, it is nearly unchanged under a specific range of cutting velocity in the experiment and improved by the flow of air cooling.

Characteristic analysis of air pressure wave generated by high-speed trains traveling through a tunnel

It is a complicated dynamic phenomenon when a transient pressure pulse is triggered by two high-speed trains passing each other in a tunnel. The air pressure pulse is a transient excitation to side wall of the car body. It can stimulate almost all vibration modes of the car body and the correlated assemblies, cause serious aerodynamic noise, and have important impacts on car body distortion, train noise, and operation safety. This article analyzes the time- frequency characteristics and main parameters of field-measured the air pressure wave, and its relationship with the train velocity as well as the vibration of the car body. Cepstrum analysis concludes that in the process of the meeting, the air pressure wave in tunnel crossing is a multiplying pressure wave instead of a superposed wave. The pressure pulse during the meeting is non-symmetrical one featured with a sharp front, large amplitude, fluctuating central sec- tion, and less sharp tail. The pulse width is inversely proportional to the train speed. As the speed increases, the impulse amplitude is amplified, and the speed of pulse front is advanced.

Pre-placement of adhesive tape around wound sites can prevent air leakage in negative pressure wound therapy procedures

The introduction of negative pressure wound therapy has revolutionized the management of complicated wounds.However,the maintenance of an effective negative pressure environment is difficult in some instances,such as wounds in close proximity to an intestinal stoma or wounds surrounded by external fixations.We found that adhesive tape adheres more easily to itself than to wet skin or uneven surfaces.Therefore,we placed adhesive tape around surgical wounds prior to covering them with foam and sealing them with more tape.As a result of the strong adhesive force between pieces of tape,this method could provide a better environmental seal,even in situations where space is limited.Pre-placed adhesive tape around the wound site prior to foam placement could provide sufficient adhesion to maintain a continuous negative pressure environment during treatment.

Control of multidrug-resistant planktonic Acinetobacter baumannii:biocidal efficacy study by atmospheric-pressure air plasma

In this research,an atmospheric-pressure air plasma is used to inactivate the multidrug-resistant Acinetobacter baumannii in liquid.The efficacy of the air plasma on bacterial deactivation and the cytobiological variations after the plasma treatment are investigated.According to colony forming units,nearly all the bacteria（6-log） are inactivated after 10 min of air plasma treatment.However,7% of the bacteria enter a viable but non-culturable state detected by the resazurin based assay during the same period of plasma exposure.Meanwhile,86% of the bacteria lose their membrane integrity in the light of SYTO 9/PI staining assay.The morphological changes in the cells are examined by scanning electron microscopy and bacteria with morphological changes are rare after plasma exposure in the liquid.The concentrations of the long-living RS,such as H2O2,NO3^- and O3,in liquid induced by plasma treatment are measured,and they increase with plasma treatment time.The changes of the intracellular ROS may be related to cell death,which may be attributed to oxidative stress and other damage effects induced by RS plasma generated in liquid.The rapid and effective bacteria inactivation may stem from the RS in the liquid generated by plasma and air plasmas may become a valuable therapy in the treatment of infected wounds.

The Influence of Atmospheric Pressure on Air Content and Pore Structure of Air-entrained Concrete

To study the effect of atmospheric pressure on the properties of fresh and hardened airentrained concrete, three kinds of air entraining agents were used for preparing air-entrained concrete in the plateaus(Lhasa, 61 kPa) and the plains(Beijing, 101 kPa). Air content, slump, compressive strength and pore structure of the three air-entrained concretes were tested in these two places. It is found that the air content of concrete under low atmospheric pressure(LAP) is 4%-36% lower than that of concrete under normal atmospheric pressure(NAP), which explaines the decrease of slump for air-entrained concrete under LAP. Pore number of hardened concrete under LAP is reduced by 48%-69%. While, the proportion of big pores(pore diameter >1 200 μm) and air void spacing factor are increased by 1.5%-7.3% and 51%-92%, respectively. The deterioration of pore structure results in a 3%-9% reduction in the compressive strength of concrete. From the results we have obtained, it can be concluded that the increase of critical nucleation energy of air bubbles and the decrease of volumetric compressibility coefficient of air in the concrete are responsible for the variation of air content and pore structure of concrete under LAP.

Influence of air pressure on mechanical effect of laser plasma shock wave

The influence of air pressure on mechanical effect of laser plasma shock wave in a vacuum chamber produced by a Nd：YAG laser has been studied. The laser pulses with pulse width of 10ns and pulse energy of about 320mJ at 1.06μm wavelength is focused on the aluminium target mounted on a ballistic pendulum, and the air pressure in the chamber changes from 2.8 × 10^ 3 to 1.01 × 10^5pa. The experimental results show that the impulse coupling coefficient changes as the air pressure and the distance of the target from focus change. The mechanical effects of the plasma shock wave on the target are analysed at different distances from focus and the air pressure.

Research on Properties of Woven Fabrics Treated by High Pressure Water Jet

The paper introduces a new technique for the treatment of the woven fabrics. Sprayed by high pressure water jet, the appearance, handle and stiffness of the fabric are improved. Other properties of the high pressure water treated fabrics like drape coefficient, air permeability, tenacity are also presented.

Nanosecond Repetitively Pulsed Dielectric Barrier Discharge in Air at Atmospheric Pressure

Dielectric barrier discharge （DBD） between two cylindrical glass containers with salt water generated by a nanosecond repetitively pulsed power generator is reported. The electrical parameters, luminous images and spectrum diagnosis are presented. It is shown that the DBD possesses a large discharge current and an intense optical emission from the nitrogen second positive system below 400 nm. The gas temperature remains very close to room temperature regardless of pulse polarity. Luminous photographs with a short exposure time down to 2 ns indicate that no filament is observed and the discharge is homogeneous.

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper,the kerosene/air rotating detonation engines(RDE)are numerically investigated,and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation,instabilities,and propulsive performance.A hybrid MPI t OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC)systems.A series of cases with the total pressure of 1 MPa,1.5 MPa,2 MPa,and the equivalence ratio of 0.9,1,1.4 are simulated.On one hand,the total pressure shows a significant impact on the instabilities of rotating detonation waves.The instability phenomenon is observed in cases with low total pressure(1 MPa)and weakened with the increase of the total pressure.The total pressure has a small impact on the detonation wave velocity and the specific impulse.On the other hand,the equivalence ratio shows a negligible influence on the instabilities,while it affects the ignition process and accounts for the detonation velocity deficit.It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition.Little difference was observed in the thrust with different equivalence ratios of 0.9,1,and 1.4.The highest specific impulse was obtained in the lean fuel cases,which is around 2700 s.The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.

Effect of Air Pressure on Hardened Layer of U75V 60 kg/m Heavy Rail after Heat Treatment

The samples cut from U75V 60 kg/m heavy rail are heated to 900 ℃ in resistance furnace and then put into air spraying channel to be cooled for 80 s, and change air pressure from 0.16 MPa to 0.33 MPa, and observe the effect of air pressure on hardened layer. The thickness and hardness of hardened layer increases with the increase of air pressure, and the thickness is more than 24 mm at the center and top fillets of rail head, and more than 15 mm at the blow fillets of rail head when air pressure is more than 0.26 MPa. During the tempering after heat treatment, tempering temperature of rail head is more than 570 ℃ when air pressure is separately 0.16 MPa, 0.20 MPa and 0.23 MPa, which is higher than finishing temperature of pearlite transformation at the cooling rate of 3 ℃/s according to CCT curve of U75V steel. When air pressure is separately 0.26, 0.30 and 0.33 MPa, the tempering temperature is 529 ℃ lower than finishing temperature of pearlite transformation at the cooling rate of 3 ℃/s. Under this condition, pearlite transformation is finished totally, so in order to reduce air consumption and control the cost, proper air pressure for U75V 60 kg/m heavy rail heat treating should be 0.26 MPa; the cooling rate increases with the increase of air pressure, and the average cooling rate on the surface of rail head is more than 3.21 ℃/s when air pressure is more than 0.26 MPa, and the largest cooling rate occurs at the top fillets of rail head.

Impacts of air pressure on the evolution of nanosecond pulse discharge products

Based on the nonequilibrium plasma dynamics of air discharge, a dynamic model of zero-dimensional plasma is established by combining the component density equation, the Boltzmann equation, and the energy transfer equation. The evolution properties of nanosecond pulse discharge （NPD） plasma under different air pressures are calculated. The results show that the air pressure has significant impacts on the NPD products and the peak values of particle number density for particles such as O atoms, 03 molecules, N2（A3） molecules in excited states, and NO molecules. It increases at first and then decreases with the increase of air pressure. On the other hand, the peak values of particle number density for N2（B3） and N2（C3） molecules in excited states are only slightly affected by the air pressure.

Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

An atmospheric pressure dielectric barrier discharge （DBD） plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experi- mental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination pro-cess, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride （PVC）, polyethylene （PE）, phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chroma- tism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

The Movement of a Mixture of Cotton with an Air Stream during Pneumatic Transport by Pipeline of Variable Cross Section

The article considers the movement of a mixture of air and raw cotton through a pipeline with a variable cross-section as a multi-speed heterogeneous medium. The regularities of the movement of components inside the pipeline, the equation of change in the porosity of cotton, air pressure and component velocities in time and along the transportation line are obtained. It was found that in the initial 20 - 25 m part of the pneumatic transport pipe there is a sharp decrease in pressure and air flow velocity, while the speed of cotton increases rapidly due to which there is a strong deformation of cotton stretching under the influence of aerodynamic force, which occurs due to the difference in the velocities of the components of the mixture, as a result of which the cotton loosens, and its porosity increases intensively.

Predicting air pressure in drainage stack of high-rise building

It is necessary to understand the features of air pressure in a drainage stack of a high-rise building for properly designing and operating a drainage system. This paper presents a mathematical model for predicting the stack performance. A step function is used to describe the effect of the air entrainment caused by the water discharged from branch pipes. An additional source term is introduced to reflect the gas-liquid interphase interaction （GLII） and stack base effect. The drainage stack is divided into upper and base parts. The air pressure in the upper part is predicted by a total variation diminishing （TVD） scheme, while in the base part, it is predicted by a characteristic line method （CLM）. The predicted results are compared with the data measured in a real-scale high- rise test building. It is found that the additional source term in the present model is effective. It intensively influences the air pressure distribution in the stack. The air pressure is also sensitive to the velocity-adjusting parameter （VAP）, the branch pipe air entrainment, and the conditions on the stack bottom.

Air Entrainment and Pressure Fields over Stepped Spillway in Skimming Flow Regime

This paper deals with some aspects of the air entrainment process along the chute of spillway and study of pressure fluctuations. The experimental study has been carried out using stepped spillway model located in the campus of Government College of Engineering, Amravati (India). It is observed that air concentration is increasing with discharge as well as with number of step. Air concentration is increasing along the length of spillway. It is also observed that the bottom mean air concentration increases with step height in the upstream reach of stepped spillway, which is prone to cavitation. The pressure profiles exhibit a wavy pattern down the stepped chute and pressure on each step increases with ratio of critical depth to step height (yc/h).