Heat Flux Characterization of DC Laminar-plasma Jets Impinging on a Flat Plate at Atmospheric Pressure

By using steady and transient methods, the total heat fluxes and the distributions of the heat flux were measured experimentally for an argon DC laminar plasma jet impinging normally on a flat plate at atmospheric pressure. Results show that the total heat fluxes measured with a steady method are a little bit higher than those with a transient method. Numerical simulation work was executed to compare with the experimental results.

Simulations of the Transient Flow Generated from a Started Flat Plate

Transient operations are commonly founded in fluid machineries such as the starting, stopping, and variations of rotor speeds, etc. Flow generated from a started fiat plate is of fundamental importance. Experiments have been done to observe the flow evolution in current researches. And in order to explore the flow in more detailed scale, some vortex methods with high resolution and other numerical methods were developed to solve various related problems by some researchers. But the promotion of vortex method to engineering application is rare due to its complexity and difficulty in specifying the boundary conditions. In order to build up a method of numerical study for such problems, a simplified model is built up with a flat plate. The development of two-dimensional viscous incompressible flow generated from an impulsively started and uniformly accelerated infinitesimally thin flat plate is simulated numerically. A dynamic mesh（DM） method based on the spring analogue and local remeshing is applied to realize the mesh motion caused by the started plate. Researches show that the mesh quality will decline under large grid shear force during the updating process. To conquer this problem, a region near the plate is separated to guarantee the mesh quality at location of interest which is the innovation of the present paper. All computations at least cover a period during which the plate translates 6 times its length. The simulated instantaneous velocity profiles, flow structures and drag coefficients under several Reynolds numbers （20 ≤ Re ≤ 126） and accelerations （20 m/s2≤ a ≤ 152 m/s2） are presented and compared with existing results in literatures. Comparisons are found to be satisfactory, confirming the validity of the current proposed method（region separated DM）. The proposed DM method is firstly used to study the transient flow generated from a started flat plate and can be used in further study of transient characteristics during transient operations of turbo machineries.

INVESTIG ATIONS OF WAKE FLOWS OF A FLAT PLATE IN STEADY, OSCILLATORY AND COMBINED FLOWS

Numerical study on near wake flows of a flat plate in three kinds of oncoming flows is made by using the discrete vortex model and improved vorticity creation method. For steady oncoming flow, both gross and detailed features of the wake flow are calculated and discussed. Then, in harmonic oscillatory oncoming flow two different wake flow patterns with K_c=2,4 and 10 are obtained respectively. Our results present a new wake flow pattern for low K_c numbers (K_c<5) describing vortex shedding, pairing and moving in a period of the oscillatory flow starting from rest. The calculated drag and inertia force coefficients are closer to experimental data from the U-tube than the previous results of vortex simulation. For in-line combined oncoming flow the vortex lock-in and dynamic characteristics are simulated. The results are shown to be in good agreement with experiments.

Pulsatile electroosmotic flow of a Maxwell fluid in a parallel flat plate microchannel with asymmetric zeta potentials

The pulsatile electroosmotic flow （PEOF） of a Maxwell fluid in a parallel flat plate microchannel with asymmetric wall zeta potentials is theoretically analyzed. By combining the linear Maxwell viscoelastic model, the Cauchy equation, and the electric field solution obtained from the linearized PoissomBoltzmann equation, a hyperbolic par- tial differential equation is obtained to derive the flow field. The PEOF is controlled by the angular Reynolds number, the ratio of the zeta potentials of the microchannel walls, the electrokinetic parameter, and the elasticity number. The main results obtained from this analysis show strong oscillations in the velocity profiles when the values of the elas- ticity number and the angular Reynolds number increase due to the competition among the elastic, viscous, inertial, and electric forces in the flow.

Non-equilibrium turbulent phenomena in transitional flat plate boundary-layer flows

Many recent laboratory experiments and numerical simulations support a non-equilibrium dissipation scaling in decaying turbulence before it reaches an equilibrium state.By analyzing a direct numerical simulation(DNS)database of a transitional boundary-layer flow,we show that the transition region and the non-equilibrium turbulence region,which are located in different streamwise zones,present different non-equilibrium scalings.Moreover,in the wall-normal direction,the viscous sublayer,log layer,and outer layer show different non-equilibrium phenomena which differ from those in grid-generated turbulence and transitional channel flows.These findings are expected to shed light on the modelling of various types of non-equilibrium turbulent flows.

Thermal Loss Analysis of a Flat Plate Solar Collector Using Numerical Simulation

In this paper,we studied theoretically and numerically heated losses of a flat solar collector to model the solar water heating system for the Kazakhstan climate condition.For different climatic zones with a growing cost for energy or lack of central heating systems,promising is to find ways to improve the energy efficiency of the solar system.The mathematical model(based on ordinary differential equation)simulated the solar system work process under different conditions.To bridge the modeling and real values results,we studied the important physical parameters such as loss coefficient,Nu,Ra,and Pr values.They impacted the efficiency of flat solar collectors and heat losses of the system.The developed mathematical models,the design and composition of the software and hardware complex,and automated control and monitoring systems allow solar hot water heating systems to increase the energy efficiency of life support systems and heat supply of buildings by reducing energy consumption for heat supply.The simulation result showed that during the daytime,the temperature of water in the collector is 70°C;the storage of heated water since heated water is cooled at night.We defined that a work period of the system can be extended with high efficiency(April-October)for Almaty region.

Numerical Investigation and Optimization of a Flat Plate Solar Collector Operating with Cu/CuO/Al_(2)O_(3)–Water Nanofluids

Nanofluids are a potential alternative to significantly improving the performance of heat transfer applications. In this work, a numerical analysis to examine the eff ect of dispersing copper(Cu), copper oxide(CuO), and aluminum(Al2O3) nanoparticles in pure water on the performance of a flat plate solar collector(FPSC) and a numerical model was proposed. The influence of the nanofluid type on the thermal efficiency was critically investigated and discussed. The eff ect of the mass flow rate on the performance was also analyzed and discussed. Based on correlations of the thermophysical properties of nanofluids, a sensitivity analysis was used to analyze the impact of the nanoparticles on the base fluid. The results indicate that the performance of the FPSC with Cu/water nanofluid was better than that of FPSCs using CuO/water or Al2O3/water nanofluids. When the mass flow rate of the nanofluids was 8.0 L/min, the efficiency of the FPSC was much greater than those at the flow rates of 5.0 L/min and 2.0 L/min. Mean enhancements in thermal efficiency of 4.44%, 4.27%, and 4.21% were observed when 2.0 L/min was applied using Cu/water, Cu O/water, and Al2O3/water nanofluids, respectively. Improvements in thermal efficiency of 2.76%, 2.53%, and 2.47% occurred when 8.0 L/min was applied.

Flashover Characteristics of Flat Plate Model Under DC Voltage in Wind-sand Condition

The influence of sand dust on discharge of external insulation has caused widespread concern.At present,the research results show wind-sand electricity has a remarkable effect on the discharge characteristics of insulator and has little influence on the discharge characteristics of air gap.The flashover of insulator strings occurs along the insulator surface and air gaps,and the sand dust deposited on the insulator surface may affect the flashover characteristics of insulator strings.This paper studies the flashover characteristics of flat plate model under DC voltage in wind-sand condition.The experimental results show that under positive polarity voltage,the flashover voltage of the flat plate model has a maximum value,while under negative polarity voltage,the flashover voltage of the flat plate model has a minimum value with a certain degree of sand dust deposition.The wind or sand in sand-dust weather has an important effect on the flashover characteristics of the flat plate model.In certain variation range of electric charge,electric charge of sand dust has little effect on the flashover voltage of flat plate model under DC voltage.The deposition of sand has significant influence on the flashover process of flat plate model,which is related to the deposition density and moisture content of sand particle.

Visual Study on Flow and Operational Characteristics of Flat Plate Closed Loop Pulsating Heat Pipes

This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.

Parametric Influence on Thermal Performance of Flat Plate Closed Loop Pulsating Heat Pipes

This paper presents an experimental study on a flat plate closed loop pulsating heat pipes. It consisted of total 40 channels with square cross section(2×2 mm2, 165 mm long) machined directly on an aluminum plate(180×120×3 mm3), which was covered by a transparent plate. The working fluid employed was ethanol. As the results, the influence parameters of thermal performance were investigated, such as filling ratio, heat load and operational orientations etc. Filling ratio was found to be a critical parameter, and its effect was rather complicated. According to its values the PHP plate could have four distinct working zones with different operational characteristics and heat transfer performance. The effect of heat load on thermal performance was found to be positive, and in general, increasing the heat load would improve heat transfer performance. In order to analyze the effect of gravity on thermal performance, three different heat modes and total seven tilt angles were tested and compared. Successful operation at all orientations with respect to gravity was also achieved.

Studies on solar flat plate collector evaporation systems for tannery effluent(soak liquor)

Heat and mass transfer analysis of an incompressible, laminar boundary layer over solar flat plate collector evapora- tion systems for tannery effluent (soak liquor) is investigated. The governing equations are solved for various liquid to air velocity ratios. Profiles of velocity, temperature and concentration as well as their gradients are presented. The heat transfer and mass transfer coefficients thus obtained are used to evaluate mass of water evaporated for an inclined fibre-reinforced plastic (FRP) solar flat plate collector (FPC) with and without cover. Comparison of these results with the experimental performance shows encouraging trend of good agreement between them.

CHARACTER OF SIMPLIFIED NAVIER-STOKES EQUATIONS FOR NEAR THE LEADING EDGE PART OF TWO-DIMENSIONAL LAMINAR FLOW PAST A FLAT PLATE

Starting from the Simplified Navier-Stokes(SNS)equations presented at first by Godovachev-Kuzmin-Tsopov,and Gao Zhi,Davis,the authors analyze the character of the SNS equations for the laminarflow near the leading edge of a flat plate and far away from the plate by using the Weiner—Hopf meth-od and Fourier transform.It is proved that the solution of the SNS equations agree with the solution of the Navier-Stokes equations for flow near the leading edge of the plate and far away from the plate.How to match the solution of the SNS equations to the Blasius solution of the boundary layer equationsis also discussed.

Experimental Study on the Skin Friction Reduction of Flat Plate by Formation of Air Cavity

The effects on the local skin friction of smooth flat plate by formation of air cavity are investigated experimentally,under the conditions of several variations of air injection angle,pore size,porous surface area and transverse step.The experimental results show that local skin friction of downstream of the porous section could be reduced at extent ranging from 50% to 90%,by injection air through pore or slot,with free stream velocities from 2 to 6 m/s.The pore size and area of air injection surface have small effect on skin friction reduction,step has significant effect on skin friction reduction.The mechanism of the skin friction reduction is due to the formation of air cavity,mixed with air and water,between the flat plate and its water boundary layer.

Computational Film Cooling Effectiveness of Dual Trench Configuration on Flat Plate at Moderate Blowing Ratios

在现在的工作，计算模拟用 ANSYS CFX 被做在与双沟使性能凉下来的电影预言改进。双沟的配置一起由二条沟组成，一条更宽的沟和其它是从更宽的渗出的狭窄的沟。在范围(0.5:5 ) 的几刮比率被调查。2.775 的 pitch-to-diameter 比率被使用。由使用双沟配置，冷却剂喷气影响了允许增加在沟旁边地传播冷却剂的沟墙 two times，减少完全在表面上盖住的喷气速度和喷气。当刮的比率增加了，结果显示这种配置增加了断热的有效性。空间地平均的断热的有效性到达了 57.6% 为在 M= 2。没有观察电影容易的根本刮的比率。双沟大小写的断热的电影有效性超过了狭窄的沟案例， laidback 在不同刮的比率的扇形的洞，扇形的洞和柱体洞。

Solar Thermal Systems Performances versus Flat Plate Solar Collectors Connected in Series

This paper shows the modeling of a solar collective heating system in order to predict the system performances. Two systems are proposed: 1) the first, Solar Direct Hot Water, which is composed of flat plate collectors and thermal storage tank, 2) the second, a Solar Indirect Hot Water in which we added an external heat exchanger of constant effectiveness to the first system. The mass flow rate by a collector is fixed to 0.04 Kg·s–1 and the total number of collectors is adjusted to 60. For the first system, the maximum average water temperature within the tank in a typical day in summer and annual performances are calculated by varying the number of collectors connected in series. For the second, this paper shows the detailed analysis of water temperature within the storage and annual performances by varying the mass flow rate on the cold side of the heat exchanger and the number of collectors in series on the hot side. It is shown that the stratification within the storage is strongly influenced by mass flow rate and the connections between collectors. It is also demonstrated that the number of collectors that can be connected in series is limited. The optimization of the mass flow rate on cold side of the heat exchanger is seen to be an important factor for the energy saving.

NUMERICAL INVESTIGATIONS INTO THE FRICTION REDUCTION BY MICROBUBBLES FOR FLAT PLATES

The two-dimensional flow on the flat plate with injected microbubbles issimulated using the software, PHOENICS (V3. 2), usually used in the CFD (Computational FluidDynamics). A set of formulas for K-ε turbulence model modified with the presence of microbubbles,is employed. With considering the effect of gravity, interfacial lift, inter-phase friction, virtualmass force and interfacial pressure on the flow with microbubbles, numerical calculations for theinfluence of variable air volume fracton as well as distribution, injecting speed, microbubblediameter and position of introducing microbubbles on the friction reduction are presented. Resultsshow that the friction reduction increases with increasing volume fraction and microbubble diameterwithin the range of 100μm, and that the velocity in the boundary layer with microbubbles is greaterthan that without microbubbles. The order of magnitude and trends of the experimental skin-frictionare reproduced well. The uniform free-stream speed in all cases is 4m/s, giving Reynolds number ofup to 20 million.

A numerical flat plate friction line and its application

This paper studies the regression of a numerical two-dimensional flat plate friction line using the RANS method with the SST k - co turbulence model. Numerical simulations with different inlet turbulence kinetic energies are first conducted. Comparing with the experimental data, the finest grid and the appropriate inlet turbulence kinetic energy are selected to compute the fiat plate friction resistance at 14 Reynolds numbers. Two numerical friction lines are obtained by the least squares root fitting method and one similar to that of the ITTC-1957 line and the cubic polynomials in logarithmic scales, and the results are compared to the friction line proposals available in the open literature. Finally, the full scale viscous resistance predictions of DTMB5415, KVLCC2, SUBOFF are compared between the numerical friction line and the friction line proposals available in the open literature based on the form factor approach. It is shown that the form factor keeps relatively constant via the numerical friction line for the bare hull, but the form factor concept in extrapolating the model test results is not appropriate for appended hulls. It is suggested that for computing a form factor numerically, it is best to use a numerical friction line.