Main flow channel index in porous sand reservoirs and its application

Based on well test interpretation,production performance analysis,overburden permeability and porosity test,gas-water core flooding test and high-pressure mercury injection,a quantitative correlation has been built of in-situ effective permeability with routine permeability and water saturation,and the ranges of Main Flow Channel Index(MFCI)are determined for different permeability levels in porous sand gas reservoirs.A new method to evaluate the in-situ effective permeability of porous sand reservoir and a correlation chart of reserves producing degree and main flow channel index are established.The results reveal that the main flow channel index of porous sand gas reservoirs has close correlation with routine matrix permeability and water saturation.The lower the routine matrix permeability and the higher the water saturation,the lower the MFCI is.If the routine matrix permeability is greater than 5.0×10-3,the MFCI is generally greater than 0.5.When the routine matrix permeability is from 1.0×10-3 to 5.0×10-3,the MFCI is mainly between 0.2 and 0.5.When the routine matrix permeability is less than 1.0×10-3,the MFCI is less than 0.2.The evaluation method of in-situ effective permeability can be used to evaluate newly discovered or not tested porous sand gas reservoirs quickly and identify whether there is tight sand gas.The correlation chart of reserves producing degree and main flow channel index can provide basis for recoverable reserves evaluation and well infilling,and provide technical support for formulation of reasonable technical policy of gas reservoir.

Laminar Flow and Heat Transfer Characteristics in Jackets of Triangular Flow Channels

有三角形的流动隧道的 jacketed 容器的 Laminar 流动和热转移特征数字地被学习在下面充分 hydrodynamically 并且热地开发了条件。在激烈的墙的经常的热流动被假定。以涡度，流函数，轴的速度部件和精力，方程基于一个有限的卷方法被写的数字程序代码。基于数字结果，流动和温度地被给，并且流动和热转移上的迪安和 Prandtl 数字的效果被检验，并且流动抵抗的关联和吝啬的 Nusselt 数字为夹克衫被开发。结果证明第二等的流动的结构是稳定的在无尺寸的弯曲比率和雷纳兹的调查范围的二个旋涡数。本地 Nusselt 数字的二座山峰与 Prandtl 和迪安数字增加显著地增加，但是本地 Nusselt 数字接近二结束并且仅仅稍微在激烈的墙的中心增加。中心和激烈的墙的二结束是为穿夹克衫的热转移的差的位置。在激烈的墙，弯曲半径，雷纳兹数字和 Prandtl 数字的一样的区域与外部一半相比卷夹克衫，三角形的流动隧道的夹克衫有更低的流动抵抗和不太吝啬的 Nusselt 数字。

Formation and evolution of gas flow channels in the abutment pressure area

The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.

Quantitative criteria for identifying main flow channels in complex porous media

To identify the type of main flow channels of complex porous media in oil and gas reservoirs,the"main flow channel index"is defined as the ratio of comprehensive permeability obtained from well test to matrix permeability obtained from core analysis or well logging.Meanwhile,a mathematical model is established based on equivalent flow assumption,the classification method for main flow channels is put forward,and quantitative characterization of main flow channels is realized.The method has been verified by analysis of typical gas reservoirs.The study results show that the"main flow channel index"can quantitatively classify types of flow channels.If the index is less than 3,the matrix pore is the main flow channel;if the index is between 3 and 20,the fracture is the main flow channel and the matrix pore acts as the supplement one;if the index is more than 20,the fracture is the only seepage channel.The dynamic analysis of typical gas reservoirs shows that the"main flow channel index"can be used to identify the type of flow channel in complex porous media,guiding the classified development of gas reservoirs,and avoiding development risk.

Fabrication of micro-flow channels on graphite composite bipolar plates using microplaning

A new method of manufacturing micro-flow channels on graphite composite bipolar plate(GCBPP) microplaning using specially designed multi-tooth tool is proposed. In this method, several or even dozens of parallel micro-flow channels ranging from 100 μm to 500 μm in width can be produced simultaneously. But, edge chippings easily occur on the rib surface of GCBPP during microplaning due to brittleness of graphite composites. Experimental results show that edge chippings result in the increase of contact resistance between bipolar plate and carbon paper at low compaction force. While the edge chippings scarcely exert influence on the contact resistance at high compaction force. Contrary to conventional view, the edge chippings can significantly improve performance of microfuel cell and big edge chippings outperform small edge chippings. In addition, the influence of technical parameters on edge chippings was investigated in order to obtain big, but not oversized edge chippings.

Analysis of ink flow channel between two rotating ink rollers

In order to research how the size of the ink flow channel is affected by the interaction of adjacent ink areas,according to the method of fluid-solid interaction,this paper analyzes the size of the ink flow channel of two ink rollers' rotation.Firstly,this paper simulates the situation of only one ink area.Secondly,this paper simulates the situation of five adjacent ink areas.Then,through comparing the simulation results of two above situations,it' s obvious that the interaction of adjacent ink areas has big effects on the ink pressure and the size of ink flow channel.At last,this paper gets the main factor that affects the size of ink flow channel in the different situations.

Numerical Analysis of Flow-Induced Vibration and Noise Generation in a Variable Cross-Section Channel

Flow channels with a variable cross-section are important components of piping system and are widely used in variousfields of engineering.Using afinite element method and modal analysis theory,flow-induced noise,mode shapes,and structure-borne noise in such systems are investigated in this study.The results demonstrate that the maximum displacement and equivalent stress are located in the part with variable cross-sectional area.The aver-age excitation force on theflow channel wall increases with theflow velocity.The maximum excitation force occurs in the range of 0–20 Hz,and then it decreases gradually in the range of 20–1000 Hz.Additionally,as theflow velocity rises from 1 to 3 m/s,the overall sound pressure level associated with theflow-induced noise grows from 49.37 to 66.37 dB.Similarly,the overall sound pressure level associated with the structure-borne noise rises from 40.27 to 72.20 dB.When theflow velocity is increased,the increment of the structure-borne noise is higher than that of theflow-induced noise.

Artificial neural network-based subgrid-scale models for LES of compressible turbulent channel flow

Fully connected neural networks(FCNNs)have been developed for the closure of subgrid-scale(SGS)stress and SGS heat flux in large-eddy simulations of compressible turbulent channel flow.The FCNNbased SGS model trained using data with Mach number Ma=3.0 and Reynolds number Re=3000 was applied to situations with different Mach numbers and Reynolds numbers.The input variables of the neural network model were the filtered velocity gradients and temperature gradients at a single spatial grid point.The a priori test showed that the FCNN model had a correlation coefficient larger than 0.91 and a relative error smaller than 0.43,with much better reconstructions of SGS unclosed terms than the dynamic Smagorinsky model(DSM).In a posteriori test,the behavior of the FCNN model was marginally better than that of the DSM in predicting the mean velocity profiles,mean temperature profiles,turbulent intensities,total Reynolds stress,total Reynolds heat flux,and mean SGS flux of kinetic energy,and outperformed the Smagorinsky model.

On interaction between freely moving bodies and fluid in a channel flow

The interaction between free fast-moving bodies(or particles)and the fluid surrounding them is studied,motivated by applications in different branches of industry,biomedicine,the environment and science such as flying droplets,ice growth,dust,impacts,food grains,sport,complexity and storms.New inviscid-based modelling and results on the behaviour of two interacting bodies inside a channel flow are described.This is followed by discussion of the more-bodies extension with a view to treating arrays of bodies in a rational manner.Significant dependences on initial conditions and on the comparative body masses and moments of inertia are found for the occurrence of body-body impacts as opposed to wall-body impacts and for the associated impact times.

Slip boundary effect on the critical Reynolds number of subcritical transition in channel flow

In this letter,the effect of slip boundary on the origin of subcritical transition in two-dimensional chan-nel flows is studied numerically and theoretically.It is shown that both the positive and the negative slip lengths will increase the critical Reynolds number of localized wave packet and hence postpone the transition.By applying a variable transformation and expanding the variables about a small slip length,it is illustrated that the slip boundary effect only exists in the second and higher order modulations of the no-slip solution,and hence explains the power law found in simulations,i.e.the relative increment of the critical Reynolds number due to the slip boundary is proportional to the square of the slip length.

Utility Impact below Bridge or Culvert Soffit on Open Channel Flow

The background to this research was a flooding incident that occurred in Bridgend, Co. Donegal, Ireland in August 2017. While several properties were flooded, a flooding case study of a single dwelling house adjacent to the Bridgend River at Riverdale, Bunamayne, Co. Donegal, Ireland is used herein. For this study the flooded site shall be referred to as the “Hegarty property”. A structure in the form of a stone arched culvert is located directly adjacent to the two-storey detached dwelling house on the Hegarty Property. While the culvert is referred to locally as a bridge, within this research the word culvert will be used in connection with the structure. The culvert has a concrete surrounded utility (watermain) crossing at a gradient below the culvert soffit on the upstream face of the structure. The utility obstructed flow through the culvert and contributed to the flooding event. Given the implication of climate change and the increased probability of more extreme flooding events, it was decided to explore the case study to ascertain the factors that contribute to flooding events when utilities are positioned at culvert or bridge structures. This work was completed to assist undergraduate students, researchers, and local authorities in a relatively unknown area of flood causation.

Effect of Mixed Vegetation of Different Heights on Open Channel Flows

Vegetation of different heights commonly grows in natural rivers, canals and wetlands and affects the biodiversity and morphological process. The role of vegetation has drawn great attention in river ecosystems and environmental management. Due to the complexity of the vegetated flow, most previous research focuses on the effect of uniformed one-layered vegetation on the flow structure and morphological process. However, less attention was paid to the impact of the mixing vegetation of different heights, which is more realistic and often occurs in natural riverine environments. This paper aims to investigate the effect of mixing three-layered vegetation on flow characteristics, particularly the velocity distrbution, via a novel experiment. Experiments were performed in a titling water flume fully covered with vegetation of three heights (10, 15 and 20 cm) arranged in a staggered pattern, which is partially submerged. Velocities at different positions along a half cross-section were measured using a mini propeller velocimeter. Observed results showed that the velocity has a distinct profile directly behind vegetation and behind the vegetation gap. The overall profile has two distinct reflections about ? below or near the top of short vegetation (h): the velocity remains almost constant in the bottom layer ( h) the velocities directly behind the middle after short vegetation increase much faster than those directly behind the short after tall vegetation. The finding in this study would help river riparian and ecosystem management. .

Overbank Flow in a Multi-Staged Open Channel: Zonal and Overall Discharge Studies

An improved divided channel method has been proposed by modelling a parameter using the function of depth ratio for a multi-stage compound channel. Experimental data suggest that as the flow depth increases over the second stage floodplain, fractional contribution of the main channel and first stage floodplain under bankfull height plays a pivotal role in shear layer and momentum distribution. Therefore, a new mathematical model has been suggested for estimating the stage-discharge relationship for staged channels of more than one floodplain using the 1D technique of overall roughness correction. .

Numerical analysis of a magnetohydrodynamic duct flow with flow channel insert under a non-uniform magnetic field

This study performs a numerical analysis of three-dimensional liquid metal(LM) magnetohydrodynamic(MHD) flows in a square duct with an FCI in a non-uniform magnetic field. The current study predicts detailed information on flow velocity, Lorentz force, pressure, current and electric potential of MHD duct flows for different Hartmann numbers. Also, the effect of the electric conductivity of FCI on the pressure drop along the main flow direction in a non-uniform magnetic field is examined. The present study investigates the features of LM MHD flows in consideration of the interdependency among the flow variables.

Orientation distribution of fibres in a channel flow of fibre suspension

The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.

Experimental study on influence of boundary on location of maximum velocity in open channel flows

The velocity dip phenomenon may occur in a part of or in the whole flow field of open channel flows due to the secondary flow effect. Based on rectangular flume experiments and the laser Doppler velocimetry, the influence of the distance to the sidewall and the aspect ratio on the velocity dip is investigated. Through application of statistical methods to the experimental results, it is proposed that the flow field may be divided into two regions, the relatively strong sidewall region and the relatively weak sidewall region. In the former region, the distance to the sidewall greatly affects the location of maximum velocity, and, in the latter region, both the distance to the sidewall and the aspect ratio influence the location of the maximum velocity.

EXPERIMENTAL STUDY ON TURBULENT FEATURES IN THE NEGATIVE TRANSPORT REGION OF ASYMMETRIC PLANE CHANNEL FLOW

Turbulent features of streamwise and vertical components of velocity in the negative transport region of asymmetric plane channel flow have been studied experimentally in details. Experiments show that turbulent fluctuations in negative transport region are suppressed, and their probability distributions are far from Gaussian. Besides, the skewness factors attain their negative maxima at the position of the maximum mean velocity, whereas the flatness factors attain their positive maxima at the same position.

The nature of near-wall convection velocity in turbulent channel flow

A novel notion of turbulent structure the local cascade structure-is introduced to study the convection phenomenon in a turbulent channel flow. A space-time cross-correlation method is used to calculate the convection velocity. It is found that there are two characteristic convection speeds near the wall, one associated with small-scale streaks of a lower speed and another with streamwise vortices and hairpin vortices of a higher speed. The new concept of turbulent structure is powerful to illustrate the dominant role of coherent structures in the near-wall convection, and to reveal also the nature of the convection-the propagation of patterns of velocity fluctuations-which is scale-dependent.

Electroosmotic oscillatory flow of micropolar fluid in microchannels:application to dynamics of blood flow in microfluidic devices

The electroosmotic flow of a micropolar fluid in a microchannel bounded by two parallel porous plates undergoing periodic vibration is studied. The equations for conservation of linear and angular momentums and Gauss＇s law of charge distribution are solved within the framework of the Debye-Hückel approximation. The fluid velocity and microrotation are assumed to depend linearly on the Reynolds number. The study shows that the amplitude of microrotation is highly sensitive to the changes in the magnitude of the suction velocity and the width of the microchannel. An increase in the micropolar parameter gives rise to a decrease in the amplitude of microrotation. Numerical estimates reveal that the microrotation of the suspended microelements in blood also plays an important role in controlling the electro-osmotically actuated flow dynamics in microbio-fluidic devices.