The computational flow rate feedback and control method, which can be used in proportional valve controlled hydraulic elevators, is discussed and analyzed. In a hydraulic elevator with this method, microprocessor rece...The computational flow rate feedback and control method, which can be used in proportional valve controlled hydraulic elevators, is discussed and analyzed. In a hydraulic elevator with this method, microprocessor receives pressure information from the pressure transducers and computes the flow rate through the proportional valve based on pressure-flow conversion real time algorithm. This hydraulic elevator is of lower cost and energy consumption than the conventional closed loop control hydraulic elevator whose flow rate is measured by a flow meter. Experiments arc carried out on a test rig which could simulate the load of hydraulic elevator. According to the experiment results, the means to modify the pressure-flow conversion algorithm are pointed out.展开更多
The effect of flow control devices(FCDs) on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1:2.5 hydraulic model and a numerical simu...The effect of flow control devices(FCDs) on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1:2.5 hydraulic model and a numerical simulation of a 1:1 geometric model.The variation coefficient(CV) was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor(TI) and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.展开更多
It is essential to characterize fluid flow in porous media to have a better understanding of petrophysical properties.Many approaches were developed to determine reservoir permeability among which the integrated analy...It is essential to characterize fluid flow in porous media to have a better understanding of petrophysical properties.Many approaches were developed to determine reservoir permeability among which the integrated analysis of hydraulic flow unit(HFU)and electrofacies(EF)is considered to be useful one.However,the application of HFU and EF analysis has not been totally understood with a limited data to develop correlation for less distance offset wells.In this study,an attempt was made to show the application of integrating HFU and EF for reliable estimation of permeability using core and wireline log data in one of the gas fields in Pakistan.The results obtained indicate that the integrated approach proposed in this study can be used,especially in less distance offset wells when a limited number of data are available for petrophysical characterization.展开更多
This study focuses on the heterogeneity of the middle Miocene syn-rift Belayim nullipore(reefal)marine sequences in the Gulf of Suez and its impacts on reservoir quality.The sequences consist of coralline algal reef l...This study focuses on the heterogeneity of the middle Miocene syn-rift Belayim nullipore(reefal)marine sequences in the Gulf of Suez and its impacts on reservoir quality.The sequences consist of coralline algal reef limestones with a highly complex dual-porosity system of primary and secondary porosities of widely varying percentages.To achieve a precise mathematical modeling of these reservoir sequences,a workflow protocol was applied to separate these sequences into a number of hydraulic flow units(HFUs)and reservoir rock types(RRTs).This has been achieved by conducting a conventional core analysis on the nullipore marine sequence.To illustrate the heterogeneity of the nullipore reservoir,the Dykstra-Parsons coefficient(V)has been estimated(V=0.91),indicating an extremely heterogeneous reservoir.A slight to high anisotropy(λ_(k))has been assigned for the studied nullipore sequences.A stratigraphic modified Lorenz plot(SMLP)was applied to define the optimum number of HFUs and barriers/baffles in each of the studied wells.Integrating the permeability-porosity,reservoir quality index-normalized porosity index(RQI-NPI)and the RQI-flow zone indicator(RQIFZI)plots,the discrete rock types(DRT)and the R35 techniques enable the discrimination of the reservoir sequences into 4 RRTs/HFUs.The RRT4 packstone samples are characterized by the best reservoir properties(moderate permeability anisotropy,with a good-to-fair reservoir quality index),whereas the RRT1 mudstone samples have the lowest flow and storage capacities,as well as the tightest reservoir quality.展开更多
168 core samples data of two production wells in the Baltim North field were used to identify the complex discrepancies in reservoir pore geometry which governing the Abu Madi reservoir fluid flow properties. Permeabi...168 core samples data of two production wells in the Baltim North field were used to identify the complex discrepancies in reservoir pore geometry which governing the Abu Madi reservoir fluid flow properties. Permeability prediction from well logs is significant goal when the core data is rarely available in most cases because<span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> of</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> its expensive cost. The hydraulic flow unit approach was used to classify reservoir rocks according to its pore aperture size in the cored wells. The predicted permeability was calculated from core porosity and core permeability relationship for each flow unit. The difference between Neutron porosity and Density porosity was recognized to distinguish different hydraulic flow units. The higher difference indicates higher quality flow unit and vice versa. For model’s verification the predicted permeability was plotted against the laboratory measured permeability in all studied wells and shows highly matching.</span></span></span>展开更多
Rock types,pore structures and permeability are essential petrophysical outputs,and they contribute considerably to the highest degree of uncertainty in reservoir characterisation.These factors have a strong influence...Rock types,pore structures and permeability are essential petrophysical outputs,and they contribute considerably to the highest degree of uncertainty in reservoir characterisation.These factors have a strong influence on exploration and field development decisions.Core analysis is the best approach for estimating permeability,assigning rock types and characterising pore networks.Wireline logs are the most often employed method for estimating the parameters at each data point of reservoirs since there are more un-cored wells than cored wells.Artificial intelligence,on the other hand,is gaining popularity in the geosciences due to the ever-increasing complexity and volume of available subsurface data.This is also obvious in the demand for faster and more accurate interpretations in order to identify reservoir characteristics in increasingly difficult and complicated petroliferous basins.Artificial Neural Networks and Self-Organizing Maps are examples of machine learning approaches that can be used in both supervised and unsupervised modes for modelling and prediction.Eocene carbonates of Mukta oilfield are the major pay rocks of strong geological heterogeneity in terms of their porosity and permeability relationship with pore structures.This paper outlines a novel method of rock fabric classification,pore structure characterization,flow unit classification and robust reservoir permeability modelling based on an integrated approach that incorporates core measurements,log data and machine learning techniques.The pore structure has been characterised by the combination of conventional core,capillary pressure and nuclear magnetic resonance data.Artificial neural network has added an adequate benefit in accurate permeability modelling by utilizing the concepts of rock classifications and hydraulic flow units.展开更多
Even though a large number of large-scale arch dams with height larger than 200 m have been built in the world, the transient groundwater flow behaviors and the seepage control effects in the dam foundations under dif...Even though a large number of large-scale arch dams with height larger than 200 m have been built in the world, the transient groundwater flow behaviors and the seepage control effects in the dam foundations under difficult geological conditions are rarely reported. This paper presents a case study on the transient groundwater flow behaviors in the rock foundation of Jinping I double-curvature arch dam, the world's highest dam of this type to date that has been completed. Taking into account the geological settings at the site, an inverse modeling technique utilizing the time series measurements of both hydraulic head and discharge was adopted to back-calculate the permeability of the foundation rocks,which effectively improves the uniqueness and reliability of the inverse modeling results. The transient seepage flow in the dam foundation during the reservoir impounding was then modeled with a parabolic variational inequality(PVI) method. The distribution of pore water pressure, the amount of leakage, and the performance of the seepage control system in the dam foundation during the entire impounding process were finally illustrated with the numerical results.展开更多
Hydraulic machinery mainly includes turbine and pump, which is closely related to national economy and people's livelihood involving aerospace industry, marine engineering, hydropower engineering, petroleum industry,...Hydraulic machinery mainly includes turbine and pump, which is closely related to national economy and people's livelihood involving aerospace industry, marine engineering, hydropower engineering, petroleum industry, chemical industry, mining industry, biomedical engineering, environmental engineering, agricultural water-soil engineering, etc.. The internal flow of hydraulic machinery is extremely complex, and its characteristics can be summarized as high Reynolds number, multi-scales, inhomogeneous and vortex-dominant unsteady turbulence which interact with the rotating dynamic boundary(rotor blade). Based on the analysis of the internal flow characteristics of hydraulic machinery, the author and his research team successively proposed a rotation correction model, a curvature corrected filter-based model, a scalable detached eddy simulation method, and a non-linear hybrid RANS/LES turbulence model to capture unsteady flow structures and then predict hydraulic performance and dynamic characteristics more accurately. According to the analysis on the internal flow, the corresponding flow control measures were put forward. It was verified by experiments that these methods could significantly improve the hydraulic performance, anti-cavitation performance and dynamic characteristics(pressure pulsation and vibration) of hydraulic machinery in a certain range of operating conditions. In addition, the mechanism how flow control measures influence internal flow was analyzed in depth, aiming at finding a feasible and effective way to improve hydraulic performance, anti-cavitation performance and dynamic characteristics of hydraulic machinery.展开更多
Natural fractures(NFs)are common in shale and tight reservoirs,where staged multi-cluster fracturing of horizontal wells is a prevalent technique for reservoir stimulation.While NFs and stress interference are recogni...Natural fractures(NFs)are common in shale and tight reservoirs,where staged multi-cluster fracturing of horizontal wells is a prevalent technique for reservoir stimulation.While NFs and stress interference are recognized as significant factors affecting hydraulic fracture(HF)propagation,the combined influence of these factors remains poorly understood.To address this knowledge gap,a novel coupled hydromechanical-damage(HMD)model based on the phase field method is developed to investigate the propagation of multi-cluster HFs in fractured reservoirs.The comprehensive energy functional and control functions are established,while incorporating dynamic fluid distribution between multiple perforation clusters and refined changes in rock mechanical parameters during hydraulic fracturing.The HMD coupled multi-cluster HF propagation model investigates various scenarios,including single HF and single NF,reservoir heterogeneity,single HF and NF clusters,and multi-cluster HFs with NF clusters.The results show that the HMD coupling model can accurately capture the impact of approach angle(θ),stress difference and cementation strength on the interaction of HF and NF.The criterion of the open and cross zones is not fixed.The NF angle(a)is not a decisive parameter to discriminate the interaction.According to the relationship between approach angle(θ)and NF angle(a),the contact relationship of HF can be divided into three categories(θ=a,θ<a,andθ>a).The connected NF can increase the complexity of HF by inducing it to form branch fracture,resulting in a fractal dimension of HF as high as2.1280 at angles of±45°.Inter-fracture interference from the heel to the toe of HF shows the phenomenon of no,strong and weak interference.Interestingly,under the influence of NFs,distant HFs from the injection can become dominant fractures.However,as a gradually increases,inter-fracture stress interference becomes the primary factor influencing HF propagation,gradually superseding the dominance of NF induced fractures.展开更多
Pore size determination of hydrocarbon reservoirs is one of the main challenging areas in reservoir studies.Precise estimation of this parameter leads to enhance the reservoir simulation,process evaluation,and further...Pore size determination of hydrocarbon reservoirs is one of the main challenging areas in reservoir studies.Precise estimation of this parameter leads to enhance the reservoir simulation,process evaluation,and further forecasting of reservoir behavior.Hence,it is of great importance to estimate the pore size of reservoir rocks with an appropriate accuracy.In the present study,a modified J-function was developed and applied to determine the pore radius in one of the hydrocarbon reservoir rocks located in the Middle East.The capillary pressure data vs.water saturation(PceSw)as well as routine reservoir core analysis include porosity(4)and permeability(k)were used to develop the J-function.First,the normalized porosity(4z),the rock quality index(RQI),and the flow zone indicator(FZI)concepts were used to categorize all data into discrete hydraulic flow units(HFU)containing unique pore geometry and bedding characteristics.Thereafter,the modified J-function was used to normalize all capillary pressure curves corresponding to each of predetermined HFU.The results showed that the reservoir rock was classified into five separate rock types with the definite HFU and reservoir pore geometry.Eventually,the pore radius for each of these HFUs was determined using a developed equation obtained by normalized J-function corresponding to each HFU.The proposed equation is a function of reservoir rock characteristics including 4z,FZI,lithology index(J*),and pore size distribution index(3).This methodology used,the reservoir under study was classified into five discrete HFU with unique equations for permeability,normalized J-function and pore size.The proposed technique is able to apply on any reservoir to determine the pore size of the reservoir rock,specially the one with high range of heterogeneity in the reservoir rock properties.展开更多
The saturation calculation in complex reservoirs remains a major challenge to the oil and gas industry.In simple formations,a tendency towards simple saturation models such as Archie or Simandoux for clean and shaly r...The saturation calculation in complex reservoirs remains a major challenge to the oil and gas industry.In simple formations,a tendency towards simple saturation models such as Archie or Simandoux for clean and shaly reservoirs respectively is always preferable.These models were found to be working effectively in homogeneous formations within which the porosity and permeability are linked in the light of a simple facies scheme.Where the rocks show some degrees of heterogeneity,the well-logs are usually affected by different factors.This adversely results in a compromised or averaged log profiles that may affect the saturation calculations.Four wells drilled across a shaly sand of high heterogeneity have been studied in the Perth Basin,Western Australia.The aim is to resolve the hydrocarbon saturation and explain the high productivity results,despite the high water saturation,obtained through a conducted formation well test across the interested reservoir zones.A new integration technique between a suite of conventional and advanced logging tools together with the capillary pressure measurements has been carried out to generate a high-resolution reservoir saturation profile,that is lithofacies dependent.Three different independent methods were used in the studied wells to calculate the saturation and to reduce the uncertainty of the final estimated profiles.The methods are the resistivity-based saturation,the NMR-based irreducible saturation,and a new application through saturation height modeling.Furthermore,through the workflow,an effective calibration for the magnetic resonance T2 cutoff has been applied that is supported by the excellent reservoir production behavior from such complex reservoir.The methodology will help resolve the saturation calculation as one of the most challenging reservoir parameters,particularly where the resistivity logs are affected in complicated shaly sand environments.The effectiveness of the workflow shines the possibility to predict high resolution facies and saturation profiles in the lack of resistivity logs.A further possibility can complete the analysis on real time basis,which can certainly provide facies and saturation profiles extended to the uncored wells.Application of this methodology in the uncored wells has shown very encouraging results in various well trajectories,either vertical,deviated or horizontal long boreholes.展开更多
基金This project is supported by State Scientific Project of the Tenth Five-year Plan of China(No.2002BA208B02)National Natural Science Foundation of China(No.50305032).
文摘The computational flow rate feedback and control method, which can be used in proportional valve controlled hydraulic elevators, is discussed and analyzed. In a hydraulic elevator with this method, microprocessor receives pressure information from the pressure transducers and computes the flow rate through the proportional valve based on pressure-flow conversion real time algorithm. This hydraulic elevator is of lower cost and energy consumption than the conventional closed loop control hydraulic elevator whose flow rate is measured by a flow meter. Experiments arc carried out on a test rig which could simulate the load of hydraulic elevator. According to the experiment results, the means to modify the pressure-flow conversion algorithm are pointed out.
基金supported by the National Natural Science Foundation of China (No.51404018)the Fundamental Research Funds for the Central Universities of China (No.FRF-TP-15-008A3)
文摘The effect of flow control devices(FCDs) on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1:2.5 hydraulic model and a numerical simulation of a 1:1 geometric model.The variation coefficient(CV) was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor(TI) and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.
文摘It is essential to characterize fluid flow in porous media to have a better understanding of petrophysical properties.Many approaches were developed to determine reservoir permeability among which the integrated analysis of hydraulic flow unit(HFU)and electrofacies(EF)is considered to be useful one.However,the application of HFU and EF analysis has not been totally understood with a limited data to develop correlation for less distance offset wells.In this study,an attempt was made to show the application of integrating HFU and EF for reliable estimation of permeability using core and wireline log data in one of the gas fields in Pakistan.The results obtained indicate that the integrated approach proposed in this study can be used,especially in less distance offset wells when a limited number of data are available for petrophysical characterization.
基金the Researchers Supporting Project number(RSP-2020/92),King Saud University,Riyadh,Saudi Arabia。
文摘This study focuses on the heterogeneity of the middle Miocene syn-rift Belayim nullipore(reefal)marine sequences in the Gulf of Suez and its impacts on reservoir quality.The sequences consist of coralline algal reef limestones with a highly complex dual-porosity system of primary and secondary porosities of widely varying percentages.To achieve a precise mathematical modeling of these reservoir sequences,a workflow protocol was applied to separate these sequences into a number of hydraulic flow units(HFUs)and reservoir rock types(RRTs).This has been achieved by conducting a conventional core analysis on the nullipore marine sequence.To illustrate the heterogeneity of the nullipore reservoir,the Dykstra-Parsons coefficient(V)has been estimated(V=0.91),indicating an extremely heterogeneous reservoir.A slight to high anisotropy(λ_(k))has been assigned for the studied nullipore sequences.A stratigraphic modified Lorenz plot(SMLP)was applied to define the optimum number of HFUs and barriers/baffles in each of the studied wells.Integrating the permeability-porosity,reservoir quality index-normalized porosity index(RQI-NPI)and the RQI-flow zone indicator(RQIFZI)plots,the discrete rock types(DRT)and the R35 techniques enable the discrimination of the reservoir sequences into 4 RRTs/HFUs.The RRT4 packstone samples are characterized by the best reservoir properties(moderate permeability anisotropy,with a good-to-fair reservoir quality index),whereas the RRT1 mudstone samples have the lowest flow and storage capacities,as well as the tightest reservoir quality.
文摘168 core samples data of two production wells in the Baltim North field were used to identify the complex discrepancies in reservoir pore geometry which governing the Abu Madi reservoir fluid flow properties. Permeability prediction from well logs is significant goal when the core data is rarely available in most cases because<span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> of</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> its expensive cost. The hydraulic flow unit approach was used to classify reservoir rocks according to its pore aperture size in the cored wells. The predicted permeability was calculated from core porosity and core permeability relationship for each flow unit. The difference between Neutron porosity and Density porosity was recognized to distinguish different hydraulic flow units. The higher difference indicates higher quality flow unit and vice versa. For model’s verification the predicted permeability was plotted against the laboratory measured permeability in all studied wells and shows highly matching.</span></span></span>
文摘Rock types,pore structures and permeability are essential petrophysical outputs,and they contribute considerably to the highest degree of uncertainty in reservoir characterisation.These factors have a strong influence on exploration and field development decisions.Core analysis is the best approach for estimating permeability,assigning rock types and characterising pore networks.Wireline logs are the most often employed method for estimating the parameters at each data point of reservoirs since there are more un-cored wells than cored wells.Artificial intelligence,on the other hand,is gaining popularity in the geosciences due to the ever-increasing complexity and volume of available subsurface data.This is also obvious in the demand for faster and more accurate interpretations in order to identify reservoir characteristics in increasingly difficult and complicated petroliferous basins.Artificial Neural Networks and Self-Organizing Maps are examples of machine learning approaches that can be used in both supervised and unsupervised modes for modelling and prediction.Eocene carbonates of Mukta oilfield are the major pay rocks of strong geological heterogeneity in terms of their porosity and permeability relationship with pore structures.This paper outlines a novel method of rock fabric classification,pore structure characterization,flow unit classification and robust reservoir permeability modelling based on an integrated approach that incorporates core measurements,log data and machine learning techniques.The pore structure has been characterised by the combination of conventional core,capillary pressure and nuclear magnetic resonance data.Artificial neural network has added an adequate benefit in accurate permeability modelling by utilizing the concepts of rock classifications and hydraulic flow units.
基金financially supported through NSERC Discovery Grant(RGPIN/4994-2014)
文摘Even though a large number of large-scale arch dams with height larger than 200 m have been built in the world, the transient groundwater flow behaviors and the seepage control effects in the dam foundations under difficult geological conditions are rarely reported. This paper presents a case study on the transient groundwater flow behaviors in the rock foundation of Jinping I double-curvature arch dam, the world's highest dam of this type to date that has been completed. Taking into account the geological settings at the site, an inverse modeling technique utilizing the time series measurements of both hydraulic head and discharge was adopted to back-calculate the permeability of the foundation rocks,which effectively improves the uniqueness and reliability of the inverse modeling results. The transient seepage flow in the dam foundation during the reservoir impounding was then modeled with a parabolic variational inequality(PVI) method. The distribution of pore water pressure, the amount of leakage, and the performance of the seepage control system in the dam foundation during the entire impounding process were finally illustrated with the numerical results.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51379120,51179100)
文摘Hydraulic machinery mainly includes turbine and pump, which is closely related to national economy and people's livelihood involving aerospace industry, marine engineering, hydropower engineering, petroleum industry, chemical industry, mining industry, biomedical engineering, environmental engineering, agricultural water-soil engineering, etc.. The internal flow of hydraulic machinery is extremely complex, and its characteristics can be summarized as high Reynolds number, multi-scales, inhomogeneous and vortex-dominant unsteady turbulence which interact with the rotating dynamic boundary(rotor blade). Based on the analysis of the internal flow characteristics of hydraulic machinery, the author and his research team successively proposed a rotation correction model, a curvature corrected filter-based model, a scalable detached eddy simulation method, and a non-linear hybrid RANS/LES turbulence model to capture unsteady flow structures and then predict hydraulic performance and dynamic characteristics more accurately. According to the analysis on the internal flow, the corresponding flow control measures were put forward. It was verified by experiments that these methods could significantly improve the hydraulic performance, anti-cavitation performance and dynamic characteristics(pressure pulsation and vibration) of hydraulic machinery in a certain range of operating conditions. In addition, the mechanism how flow control measures influence internal flow was analyzed in depth, aiming at finding a feasible and effective way to improve hydraulic performance, anti-cavitation performance and dynamic characteristics of hydraulic machinery.
基金supported by the National Natural Science Foundation of China(No.52174045)。
文摘Natural fractures(NFs)are common in shale and tight reservoirs,where staged multi-cluster fracturing of horizontal wells is a prevalent technique for reservoir stimulation.While NFs and stress interference are recognized as significant factors affecting hydraulic fracture(HF)propagation,the combined influence of these factors remains poorly understood.To address this knowledge gap,a novel coupled hydromechanical-damage(HMD)model based on the phase field method is developed to investigate the propagation of multi-cluster HFs in fractured reservoirs.The comprehensive energy functional and control functions are established,while incorporating dynamic fluid distribution between multiple perforation clusters and refined changes in rock mechanical parameters during hydraulic fracturing.The HMD coupled multi-cluster HF propagation model investigates various scenarios,including single HF and single NF,reservoir heterogeneity,single HF and NF clusters,and multi-cluster HFs with NF clusters.The results show that the HMD coupling model can accurately capture the impact of approach angle(θ),stress difference and cementation strength on the interaction of HF and NF.The criterion of the open and cross zones is not fixed.The NF angle(a)is not a decisive parameter to discriminate the interaction.According to the relationship between approach angle(θ)and NF angle(a),the contact relationship of HF can be divided into three categories(θ=a,θ<a,andθ>a).The connected NF can increase the complexity of HF by inducing it to form branch fracture,resulting in a fractal dimension of HF as high as2.1280 at angles of±45°.Inter-fracture interference from the heel to the toe of HF shows the phenomenon of no,strong and weak interference.Interestingly,under the influence of NFs,distant HFs from the injection can become dominant fractures.However,as a gradually increases,inter-fracture stress interference becomes the primary factor influencing HF propagation,gradually superseding the dominance of NF induced fractures.
文摘Pore size determination of hydrocarbon reservoirs is one of the main challenging areas in reservoir studies.Precise estimation of this parameter leads to enhance the reservoir simulation,process evaluation,and further forecasting of reservoir behavior.Hence,it is of great importance to estimate the pore size of reservoir rocks with an appropriate accuracy.In the present study,a modified J-function was developed and applied to determine the pore radius in one of the hydrocarbon reservoir rocks located in the Middle East.The capillary pressure data vs.water saturation(PceSw)as well as routine reservoir core analysis include porosity(4)and permeability(k)were used to develop the J-function.First,the normalized porosity(4z),the rock quality index(RQI),and the flow zone indicator(FZI)concepts were used to categorize all data into discrete hydraulic flow units(HFU)containing unique pore geometry and bedding characteristics.Thereafter,the modified J-function was used to normalize all capillary pressure curves corresponding to each of predetermined HFU.The results showed that the reservoir rock was classified into five separate rock types with the definite HFU and reservoir pore geometry.Eventually,the pore radius for each of these HFUs was determined using a developed equation obtained by normalized J-function corresponding to each HFU.The proposed equation is a function of reservoir rock characteristics including 4z,FZI,lithology index(J*),and pore size distribution index(3).This methodology used,the reservoir under study was classified into five discrete HFU with unique equations for permeability,normalized J-function and pore size.The proposed technique is able to apply on any reservoir to determine the pore size of the reservoir rock,specially the one with high range of heterogeneity in the reservoir rock properties.
文摘The saturation calculation in complex reservoirs remains a major challenge to the oil and gas industry.In simple formations,a tendency towards simple saturation models such as Archie or Simandoux for clean and shaly reservoirs respectively is always preferable.These models were found to be working effectively in homogeneous formations within which the porosity and permeability are linked in the light of a simple facies scheme.Where the rocks show some degrees of heterogeneity,the well-logs are usually affected by different factors.This adversely results in a compromised or averaged log profiles that may affect the saturation calculations.Four wells drilled across a shaly sand of high heterogeneity have been studied in the Perth Basin,Western Australia.The aim is to resolve the hydrocarbon saturation and explain the high productivity results,despite the high water saturation,obtained through a conducted formation well test across the interested reservoir zones.A new integration technique between a suite of conventional and advanced logging tools together with the capillary pressure measurements has been carried out to generate a high-resolution reservoir saturation profile,that is lithofacies dependent.Three different independent methods were used in the studied wells to calculate the saturation and to reduce the uncertainty of the final estimated profiles.The methods are the resistivity-based saturation,the NMR-based irreducible saturation,and a new application through saturation height modeling.Furthermore,through the workflow,an effective calibration for the magnetic resonance T2 cutoff has been applied that is supported by the excellent reservoir production behavior from such complex reservoir.The methodology will help resolve the saturation calculation as one of the most challenging reservoir parameters,particularly where the resistivity logs are affected in complicated shaly sand environments.The effectiveness of the workflow shines the possibility to predict high resolution facies and saturation profiles in the lack of resistivity logs.A further possibility can complete the analysis on real time basis,which can certainly provide facies and saturation profiles extended to the uncored wells.Application of this methodology in the uncored wells has shown very encouraging results in various well trajectories,either vertical,deviated or horizontal long boreholes.