The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages i...The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content (10%) of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.展开更多
In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-...In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.展开更多
The active power loop flow(APLF)may be caused by impropriate network configuration,impropriate parameter settings,and/or stochastic bus powers.The power flow controllers,e.g.,the unified power flow controller(UPFC),ma...The active power loop flow(APLF)may be caused by impropriate network configuration,impropriate parameter settings,and/or stochastic bus powers.The power flow controllers,e.g.,the unified power flow controller(UPFC),may be the reason and the solution to the loop flows.In this paper,the critical existence condition of the APLF is newly integrated into the simultaneous power flow model for the system and UPFC.Compared with the existing method of alternatively solving the simultaneous power flow and sensitivity-based approaching to the critical existing condition,the integrated power flow needs less iterations and calculation time.Besides,with wind power fluctuation,the interval power flow(IPF)is introduced into the integrated power flow,and solved with the affine Krawcyzk iteration to make sure that the range of active power setting of the UPFC not yielding the APLF.Compared with Monte Carlo simulation,the IPF has the similar accuracy but less time.展开更多
1 INTRODUCTIONGas and liquid distributions in a self-aspirated reverse flow jet loop reactor dependchiefly on the aspiration and the breakup against gas phase by the liquid nozzle aswell as the redistribution in the d...1 INTRODUCTIONGas and liquid distributions in a self-aspirated reverse flow jet loop reactor dependchiefly on the aspiration and the breakup against gas phase by the liquid nozzle aswell as the redistribution in the draft tube.It has also been noted that effective diffu-sion or backmixing in the reactor has great influence on the flow and mass transferrates.In this case,accurate descriptions about the fluid flow and diffusion conditions inthe reactor are most necessary for effective amplification of them.展开更多
1 INTRODUCTIONSelf-aspirated reversed flow jet loop reactors,characterized by a well defined flow pat-tern,well better dispersing effects,relatively low power consumption and a high masstransfer coefficient,are widely...1 INTRODUCTIONSelf-aspirated reversed flow jet loop reactors,characterized by a well defined flow pat-tern,well better dispersing effects,relatively low power consumption and a high masstransfer coefficient,are widely used in chemical engineering,especially in biochemicalengineering.The characteristics of such reactors are highly random or stochastic due tothe influence of a variety of phenomena such as jetting and bubbling of the展开更多
New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reacto...New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reactor. The pores blocking models were created based on the standard blocking law and the intermediate blocking law, and then the cake layer models were developed based on the hydrodynamic theory in which the calculation method of porosity of cake layer was newly corrected. The Air-Water-FCC equilibrium catalysts cold model experiment was used to verify the relevant models.Results showed that the calculated values fitted well with experimental data with a relative error of less than 10%.展开更多
Multiple loop heat pipes which have two evaporators and two condensers in one loop are a kind of active heat transfer device. Since they have two evaporators and two condensers, the operating mode also becomes multipl...Multiple loop heat pipes which have two evaporators and two condensers in one loop are a kind of active heat transfer device. Since they have two evaporators and two condensers, the operating mode also becomes multiple. This work discusses the cases that multiple loop heat pipes were operated with one condenser at high temperature and the other at low temperature. To avoid the high temperature returning liquid and keep the multiple loop heat pipes work properly, the flow regulator which was made of polyethylene was designed, fabricated and applied in this test. The effect of flow regulator was confirmed and analyzed. In the test that large temperature difference existed between two sinks, it can be found according to the result that the flow regulator worked effectively and prevented the high temperature vapor to enter the inlet of common liquid line, which can keep the evaporators and returning liquid to operate at low temperature. With the increment of heat loads and the temperature difference between two sinks, the pressure difference between two condensers became larger and larger. When the pressure difference was larger than the flow regulator’s capillary force, the flow regulator could not work properly because the high temperature vapor began to flow through the flow regulator. According to the test data, the flow regulator can work properly within the sinks’ temperature 0°C/60°C and the two evaporators’ heat load 30/30 W.展开更多
This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined d...This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.展开更多
Mathematical modeling of pulsating heat pipes through ‘first’ principles is a contemporary problem which remains quite elusive. Simplifications and assumptions made in all the modeling approaches developed so far re...Mathematical modeling of pulsating heat pipes through ‘first’ principles is a contemporary problem which remains quite elusive. Simplifications and assumptions made in all the modeling approaches developed so far render them unsuitable for engineering design. In this paper, a more realistic modeling scheme is presented which provides considerable try for thought toward the next progressive step. At high enough heat flux level, closed loop pulsating heat pipes experience a bulk internal unidirectional fluid circulation. Under such a condition, conventional two-phase flow modeling in capillary tubes may be applied. This has been attempted for single-loop PHPs. A homogeneous model and a separated two-fluid flow model based on simultaneous conservation of mass, momentum and energy, have been developed for an equivalent ‘open flow’ system. The model allows prediction of two-phase flow parameters in each sub-section of the device thereby providing important insights into its operation. The concept of ‘void fraction constraint’ in pulsating heat pipe operation is introduced and its relevance to future modeling attempts is outlined.展开更多
Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid...Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid velocities.The flow rates in the two branches were measured accurately to determine how the two considered phases distribute in the two outlets.The experimental results have shown that when the two outlet pressures are asymmetric,the two-phase flow always tends to flow into the outlet which has a lower pressure.As the inlet liquid velocity increases,however,the two-phase flow gradually tends to split evenly.Compared with the experiment results,the pressure difference between the two outlets can be determined more accurately by means of numerical simulation.The trends of experimental results and simulations are in very good agreement.展开更多
This work investigated the flow-accelerated corrosion (FAC) behavior of 13Cr in a wet CO2-containing environment at different flowing gas velocities mid impinging mlgles, with the natural-gas pipeline environment si...This work investigated the flow-accelerated corrosion (FAC) behavior of 13Cr in a wet CO2-containing environment at different flowing gas velocities mid impinging mlgles, with the natural-gas pipeline environment simulated by a self-assembled impingement jet sys- tem. Surface molphology determination, electrochemical measurements, mid hydromechaziics numerical analysis were cmlied out to study the FAC behavior. The results demonstrate that pitting corrosion was the primary mode of corrosion in 13Cr stainless steel. High-flow-rate gas destroyed the passive film mid decreased the pitting potential, resulting in more serious corrosion. The corrosion degree witk various im- pact mlgles showed the following order: 90~ 〉 60~ 〉 45~. The shear force and the electrolyte from the flowing gas were concluded to be the determinm^t factors of FAC, whereas the shear force was the main factor responsible for destroying the passive film.展开更多
Asphaltene deposition is one of the most seri- ous problems, which usually occurs in oil wells, petroleum production, oil processing, and transportation facilities. Deposition of heavy organic components, especially a...Asphaltene deposition is one of the most seri- ous problems, which usually occurs in oil wells, petroleum production, oil processing, and transportation facilities. Deposition of heavy organic components, especially asphaltene, can lead to wellbore blockage and impacts well economics due to reduction in oil production. Therefore, it is necessary to pay more attention to finding some solution to overcome this problem. In this study, a pipe-loop apparatus for investigation of oil stability was employed to measure deposition thickness using a thermal method. The effects of many factors such as oil type, oil temperature, oil velocity, inhibitors, and solvents on asphaltene deposition were investigated. The results showed that the deposition increased with the increasing value of the colloidal insta- bility index. Besides, the deposition thickness increased with the decreasing velocity of oil, but did not change with oil temperature. In addition, n-heptane could result in more deposition; however, toluene had no effect on the deposi- tion. Branched dodecyl benzene sulfonic acid (Branched DBSA) and Linear DBSA as inhibitors decreased the rate of asphaltene deposition.展开更多
基金support from Subtopics of National Science and Technology Major Project(2011ZX05026-004-03)the National Natural Science Foundation of China (51104167)
文摘The natural gas pipeline from Platform QKI8-1 in the southwest of Bohai Bay to the onshore processing facility is a subsea wet gas pipeline exposed to high pressure and low temperature for a long distance. Blockages in the pipeline occur occasionally. To maintain the natural gas flow in the pipeline, we proposed a method for analyzing blockages and ascribed them to the hydrate formation and agglomeration. A new high-pressure flow loop was developed to investigate hydrate plug formation and hydrate particle size, using a mixture of diesel oil, water, and natural gas as experimental fluids. The influences of pressure and initial flow rate were also studied. Experimental results indicated that when the flow rate was below 850 kg/h, gas hydrates would form and then plug the pipeline, even at a low water content (10%) of a water/oil emulsion. Furthermore, some practical suggestions were made for daily management of the subsea pipeline.
基金Project(2008B-2901) supported by China National Petroleum Corporation
文摘In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.
基金the National Natural Science Foundation of China(Grant No.51877061).
文摘The active power loop flow(APLF)may be caused by impropriate network configuration,impropriate parameter settings,and/or stochastic bus powers.The power flow controllers,e.g.,the unified power flow controller(UPFC),may be the reason and the solution to the loop flows.In this paper,the critical existence condition of the APLF is newly integrated into the simultaneous power flow model for the system and UPFC.Compared with the existing method of alternatively solving the simultaneous power flow and sensitivity-based approaching to the critical existing condition,the integrated power flow needs less iterations and calculation time.Besides,with wind power fluctuation,the interval power flow(IPF)is introduced into the integrated power flow,and solved with the affine Krawcyzk iteration to make sure that the range of active power setting of the UPFC not yielding the APLF.Compared with Monte Carlo simulation,the IPF has the similar accuracy but less time.
基金This work was supported by the National Science Foundation of China.
文摘1 INTRODUCTIONGas and liquid distributions in a self-aspirated reverse flow jet loop reactor dependchiefly on the aspiration and the breakup against gas phase by the liquid nozzle aswell as the redistribution in the draft tube.It has also been noted that effective diffu-sion or backmixing in the reactor has great influence on the flow and mass transferrates.In this case,accurate descriptions about the fluid flow and diffusion conditions inthe reactor are most necessary for effective amplification of them.
基金Supported by the Science Foundation of the ChineseAcademy of Science.
文摘1 INTRODUCTIONSelf-aspirated reversed flow jet loop reactors,characterized by a well defined flow pat-tern,well better dispersing effects,relatively low power consumption and a high masstransfer coefficient,are widely used in chemical engineering,especially in biochemicalengineering.The characteristics of such reactors are highly random or stochastic due tothe influence of a variety of phenomena such as jetting and bubbling of the
基金financially supported by the National Key Research & Development Program of China (2016YFB0301600)
文摘New modified combination mathematical models including the pores blocking models and the cake layer models were developed to describe the continuous cross-flow microfiltration in an airlift external loop slurry reactor. The pores blocking models were created based on the standard blocking law and the intermediate blocking law, and then the cake layer models were developed based on the hydrodynamic theory in which the calculation method of porosity of cake layer was newly corrected. The Air-Water-FCC equilibrium catalysts cold model experiment was used to verify the relevant models.Results showed that the calculated values fitted well with experimental data with a relative error of less than 10%.
文摘Multiple loop heat pipes which have two evaporators and two condensers in one loop are a kind of active heat transfer device. Since they have two evaporators and two condensers, the operating mode also becomes multiple. This work discusses the cases that multiple loop heat pipes were operated with one condenser at high temperature and the other at low temperature. To avoid the high temperature returning liquid and keep the multiple loop heat pipes work properly, the flow regulator which was made of polyethylene was designed, fabricated and applied in this test. The effect of flow regulator was confirmed and analyzed. In the test that large temperature difference existed between two sinks, it can be found according to the result that the flow regulator worked effectively and prevented the high temperature vapor to enter the inlet of common liquid line, which can keep the evaporators and returning liquid to operate at low temperature. With the increment of heat loads and the temperature difference between two sinks, the pressure difference between two condensers became larger and larger. When the pressure difference was larger than the flow regulator’s capillary force, the flow regulator could not work properly because the high temperature vapor began to flow through the flow regulator. According to the test data, the flow regulator can work properly within the sinks’ temperature 0°C/60°C and the two evaporators’ heat load 30/30 W.
基金the Ger man National Science Foundation (GR-412/33-2)Shanghai Leading Academic Discipline Project (No.B604)
文摘This paper presents an experimental study including visualization on a flat plate closed loop pulsating heat pipes.It consists of a total of 40 channels with square cross section(2 mm×2 mm,165 mm long) machined directly on an aluminum plate(180 mm×120 mm×3 mm) covered by a transparent plate.The working fluid employed is ethanol.As a result,various flow patterns and their transitions are observed and found to be related to the fluid fill ratio,input heat load and the device orientation.Also the operational characteristics and working mechanism are discussed.
基金German National Science Foundation (DFG)(No. GR-412/22)
文摘Mathematical modeling of pulsating heat pipes through ‘first’ principles is a contemporary problem which remains quite elusive. Simplifications and assumptions made in all the modeling approaches developed so far render them unsuitable for engineering design. In this paper, a more realistic modeling scheme is presented which provides considerable try for thought toward the next progressive step. At high enough heat flux level, closed loop pulsating heat pipes experience a bulk internal unidirectional fluid circulation. Under such a condition, conventional two-phase flow modeling in capillary tubes may be applied. This has been attempted for single-loop PHPs. A homogeneous model and a separated two-fluid flow model based on simultaneous conservation of mass, momentum and energy, have been developed for an equivalent ‘open flow’ system. The model allows prediction of two-phase flow parameters in each sub-section of the device thereby providing important insights into its operation. The concept of ‘void fraction constraint’ in pulsating heat pipe operation is introduced and its relevance to future modeling attempts is outlined.
基金the National Science and Technology Major Project of China(No.2016ZX05028-004-003).
文摘Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid velocities.The flow rates in the two branches were measured accurately to determine how the two considered phases distribute in the two outlets.The experimental results have shown that when the two outlet pressures are asymmetric,the two-phase flow always tends to flow into the outlet which has a lower pressure.As the inlet liquid velocity increases,however,the two-phase flow gradually tends to split evenly.Compared with the experiment results,the pressure difference between the two outlets can be determined more accurately by means of numerical simulation.The trends of experimental results and simulations are in very good agreement.
基金supported by the National Environmental Corrosion Platform (NECP)the National Key Technology R&D Program of China (No. 2011BAK06B01-01-02)the Fundamental Research Funds for the Central Universities of china (No. FRF-BR-17-028A)
文摘This work investigated the flow-accelerated corrosion (FAC) behavior of 13Cr in a wet CO2-containing environment at different flowing gas velocities mid impinging mlgles, with the natural-gas pipeline environment simulated by a self-assembled impingement jet sys- tem. Surface molphology determination, electrochemical measurements, mid hydromechaziics numerical analysis were cmlied out to study the FAC behavior. The results demonstrate that pitting corrosion was the primary mode of corrosion in 13Cr stainless steel. High-flow-rate gas destroyed the passive film mid decreased the pitting potential, resulting in more serious corrosion. The corrosion degree witk various im- pact mlgles showed the following order: 90~ 〉 60~ 〉 45~. The shear force and the electrolyte from the flowing gas were concluded to be the determinm^t factors of FAC, whereas the shear force was the main factor responsible for destroying the passive film.
基金the supports from Islamic Azad University,Kermanshah Branch
文摘Asphaltene deposition is one of the most seri- ous problems, which usually occurs in oil wells, petroleum production, oil processing, and transportation facilities. Deposition of heavy organic components, especially asphaltene, can lead to wellbore blockage and impacts well economics due to reduction in oil production. Therefore, it is necessary to pay more attention to finding some solution to overcome this problem. In this study, a pipe-loop apparatus for investigation of oil stability was employed to measure deposition thickness using a thermal method. The effects of many factors such as oil type, oil temperature, oil velocity, inhibitors, and solvents on asphaltene deposition were investigated. The results showed that the deposition increased with the increasing value of the colloidal insta- bility index. Besides, the deposition thickness increased with the decreasing velocity of oil, but did not change with oil temperature. In addition, n-heptane could result in more deposition; however, toluene had no effect on the deposi- tion. Branched dodecyl benzene sulfonic acid (Branched DBSA) and Linear DBSA as inhibitors decreased the rate of asphaltene deposition.