Size dependent flow behaviors of particles in hydrocyclone based on multiphase simulation

To investigate the flow behaviors of different size particles in hydrocyclone,a designed process was numerically simulated by the transient solver,where the quartz particles possessing a size distribution were injected into a 100 mm diameter hydrocyclone with the steady water field and air core inside.A lab experimental work has validated the chosen models in simulation by comparing the classification efficiency results.The simulated process shows that the 25 μm quartz particles,close to the cut size,need much more time than the finer and coarser particles to reach the steady flow rate on the outlets of hydrocyclone.For the particles in the inner swirl,with the quartz size increasing from 5 to 25 μm,the particles take more time to enter the vortex finder.The 25 μm quartz particles move outward in the radial direction when they go up to the vortex finder,which is contrary to the quartz particles of 5 μm and 15 μm as they are closely surrounding the air core.The studies reveal that the flow behaviors of particles inside the hydrocyclone depend on the particle size.

The Effect of Sparger Geometry on Gas Bubble Flow Behaviors Using Electrical Resistance Tomography

By electrical resistance tomography (ERT) the cross sectional profiles of gas hold-up in a φ56mm bubble column are obtained with four designs of gas sparger. The effect of sparger geometry on the bubble distribution is re-vealed by applying a sensitivity conjugated gradients reconstruction method (SCG). Experimental results show that over-all hold-up obtained by ERT is generally in good agreement with those measured with the pressure transducer and the ERT system produces informative evidence that the radial profiles of hold-up is very similar to the sparger design in the lower section of bubble column. Meanwhile, the rise velocity of bubble swarm and the Sauter mean bubble size are evaluated using ERT based on dynamic gas disengagement theory. The experimental results are in good agreement with correlations and conventional estimation obtained using pressure transmitter methods.

Flow Behaviors of Non-spherical Granules in Rectangular Hopper

Flow behaviors of four kinds of granular particles(i.e. sphere,ellipsoid,hexahedron and binary mixture of sphere and hexahedron) in rectangular hoppers were experimentally studied. The effects of granular shape and hopper structure on flow pattern,discharge fraction,mean particle residence time and tracer concentration distribu-tion were tested based on the visual observation and particle tracer technique. The results show that particle shape affects significantly the flow pattern. The flow patterns of sphere,ellipsoid and binary mixture are all parabolic shape,and the flow pattern shows no significant difference with the change of wedge angle. The flowing zone be-comes more sharp-angled with the increasing outlet size. The flow pattern of hexahedron is featured with straight lines. The discharge rates are in increasing order from hexahedron,sphere,binary mixture to ellipsoid. The dis-charge rate also increases with the wedge angle and outlet size. The mean particle residence time becomes shorter when the outlet size increases. The difference of mean particle residence time between the maximum and minimum values decreases as the wedge angle increases. The residence time of hexahedron is the shortest. The tracer concen-tration distribution of hexahedron at any height is more uniform than that of binary mixture. The tracer concentra-tion of sphere in the middle is lower than that near the wall,and the contrary tendency is found for ellipsoid particles.

Analog-Circuit Model of FGH96 Superalloy Hot Deformation Behaviors Based on Artificial Neural Network

At the present time, numerical models （such as, numerical simulation based on FEM） adopted broadly in technological design and process control in forging field can not implement the realtime control of material forming process. It is thus necessary to establish a dynamic model fitting for the real-time control of material deformation processing in order to increase production efficiency, improve forging qualities and increase yields. In this paper, hot deformation behaviors of FGH96 superalloy are characterized by using hot compressive simulation experiments. The artificial neural network （ANN） model of FGH96 superalloy during hot deformation is established by using back propagation （BP） network. Then according to electrical analogy theory, its analog-circuit （AC） model is obtained through mapping the ANN model into analog circuit. Testing results show that the ANN model and the AC model of FGH96 superalloy hot deformation behaviors possess high predictive precisions and can well describe the superalloy＇s dynamic flow behaviors. The ideas proposed in this paper can be applied in the real-time control of material deformation processing.

A phenomenological model for plastic flow behavior of rotating band material with a large temperature range

The plastic flow behavior of the rotating band material is investigated in this paper. The rotating band material is processed from H96 brass alloy, which is hardened to a much higher yield strength compared to the annealed one. The dynamically uniaxial compression behavior of the material is tested using the split Hopkinson pressure bar(SHPB) with temperature and strain rate ranging from 297 to 1073 K and500 to 3000 s^(-1), respectively, and a phenomenological plastic flow stress model is developed to describe the mechanical behavior of the material. The material is found to present noticeable temperature sensitivity and weak strain-rate sensitivity. The construction of the plastic flow stress model has two steps. Firstly, three univariate stress functions, taking plastic strain, plastic strain rate and temperature as independent variable, respectively, are proposed by fixing the other two variables. Then, as the three univariate functions describe the special cases of flow stress behavior under various conditions, the principle of stress compatibility is adopted to obtain the complete flow stress function. The numerical results show that the proposed plastic flow stress model is more suitable for the rotating band material than the existing well-known models.

Dynamic recrystallization kinetics of as-cast AZ91D alloy

The flow behavior and dynamic recrystallization（DRX） behavior of an as-cast AZ91 D alloy were investigated systematically by applying the isothermal compression tests in temperature range of 220-380 ℃ and strain rate range of 0.001-1 s^-1.The effect of temperature and strain rate on the DRX behavior was discussed.The results indicate that the nucleation and growth of dynamic recrystallized grains easily occur at higher temperatures and lower strain rates.To evaluate the evolution of dynamic recrystallization,the DRX kinetics model was proposed based on the experimental data of true stress-true strain curves.It was revealed that the volume fraction of dynamic recrystallized grains increased with increasing strain in terms of S-curves.A good agreement between the proposed DRX kinetics model and microstructure observation results validates the accuracy of DRX kinetics model for AZ91 D alloy.

Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate

Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.

Hot deformation behavior and microstructural evolution of Al-Zn-Mg-0.25Sc-Zr alloy during compression at elevated temperatures

The hot deformation behavior of Al-Zn-Mg-0.25Sc-Zr alloy and its microstructural evolution were investigated by isothermal axisymmetric hot compression tests at temperatures from 340 to 500°C and strain rates ranging from 0.001 to 10 s -1 .The steady flow stress increased with increasing the strain rate or decreasing the deformation temperature,which can be described by a hyperbolic-sine constitutive equation with the deformation activation energy of 150.25 kJ/mol.The tendency of dynamic recrystallization enhanced at high deforming temperatures and low strain rates,which corresponded to low Z values.With decreasing Z value,the main softening mechanism of the alloy transformed from dynamic recovery to dynamic recrystallization, correspondingly,the subgrain size increased and the dislocation density decreased.

Hot deformation behavior of spray forming LSHR alloy using constitutive equation and processing map

Flow behaviors of spray forming low solvus high refractory (LSHR) alloy were investigated using hot compression tests performed on a Gleeble?3500 thermal mechanical simulator at temperatures of 1020?1150 °C and strain rates of 0.0003?1.0 s?1. The constitutive equation was established, power dissipation (η) maps and hot processing maps were plotted. The microstructure evolution and dislocation distribution of domains with different values of η in power dissipation maps were also observed. The results show that the flow stress increases with decreasing temperature and increasing strain rate. The activation energy of the spray forming LSHR alloy is 1243.86 kJ/mol. When the value of η is 0.36 at the strain of 0.5, the domain in the processing map shows characteristics of typical dynamic recrystallization (DRX) and low dislocation density. According to the microstructure evolution and processing maps, the optimum processing condition for good hot workability of spray forming LSHR alloy can be summed up as:temperature range 1110?1150 °C; strain rate range 0.01?0.3 s?1.

Modification of constitutive model and evolution of activation energy on 2219 aluminum alloy during warm deformation process

To investigate the flow behavior of 2219 Al alloy during warm deformation, the thermal compression test was conducted in the temperature range of 483-573 K and the strain rate range of 0.001-5 s^-1 on a Gleeble-3500 thermomechanical simulation unit. The true stress-true strain curves obtained showed that the flow stress increased with the decrease in temperature and/or the increase in strain rate and the softening mechanism primarily proceeded via dynamic recovery. The modification on the conventional Arrhenius-type constitutive model approach was made, the material variables and activation energy were determined to be dependent on the deformation parameters. The modified flow stresses were found to be in close agreement with the experimental values. Furthermore, the activation energy obtained under different deformation conditions showed that it decreased with the rise in temperature and/or strain rate, and was also affected by the coupled effect of strain and strain rate.

Modified constitutive model and workability of 7055 aluminium alloy in hot plastic compression

To obtain flow behavior and workability of 7055 aluminium alloy during hot deformation,hot compression tests at different temperatures and strain rates are conducted.True stress?strain curves of 7055 aluminium alloy under different conditions are obtained and the flow stress increases with ascending strain rate and descending temperature.For Arrhenius constitutive equation,each material parameter is set as a constant,which will bring forth large error for predicting flow behavior.In this work,material parameters are fitted as a function of temperature or strain rate based on experimental results and a modified constitutive equation is established for more accurate prediction of flow behavior of 7055 aluminium alloy.The effects of temperature and strain rate on power dissipation and instability are analyzed to establish a processing map of 7055 aluminium alloy.The dominant deformation mechanism for microstructure evolution at different deformation conditions can be determined and high efficiency of power dissipation may be achieved from power dissipation map.Meanwhile,proper processing parameters to avoid flow instability can be easily acquired in instability map.According to the processing map,optimized processing parameters of 7055 aluminium alloy are temperature of 673?723 K and strain rate of 0.01?0.4 s^?1,during which its efficiency of power dissipation is over 30%.Finite element method(FEM)is used to obtain optimized parameter in hot rolling process on the basis of processing map.

Constitutive modeling of flow behavior of precipitation-hardened AA7022-T6 aluminum alloy at elevated temperature

The thermomechanical behavior of precipitation-hardened aluminum alloy AA7022-T6 was studied using isothermal compression at temperatures of 623−773 K and strain rates of 0.01−1 s^−1.The experimental results indicated that dynamic recrystallization(DRX)is a predominant hot deformation mechanism,especially at elevated temperatures and low strain rates.The modified Johnson−Cook(J−C)and the strain compensated Arrhenius-type models were developed to predict the hot flow behavior under different deformation conditions.The correlation coefficients of modified J−C model and the strain compensated Arrhenius-type models were 0.9914 and 0.9972,respectively,their average relative errors(ARE)were 6.074%and 4.465%,respectively,and their root mean square errors(RMSE)were 10.611 and 1.665 MPa,respectively,indicating that the strain compensated Arrhenius-type model can predict the hot flow stress of AA7022-T6 aluminum alloy with an appropriate accuracy.

Modeling of dynamic recrystallization volume fraction evolution for AlCu4SiMg alloy and its application in FEM

To improve the understanding of coupling effect between dynamic recrystallization(DRX)behaviors and flow behaviors of as-cast AlCu4 SiMg, a finite element(FE) simulation equipped with the models of DRX evolution was implemented. A series of isothermal compression tests were performed primarily on a Gleeble-3500 thermo-mechanical simulator in a temperature range of 648-748 K and a strain rate range of 0.01-10 s-1.According to the measured true stress-strain data,the strain hardening rate curves(dσ/dε versus σ) were plotted to identify the critical strains for DRX initiation(εc). By further derivation of the related material constants, the DRX volume fraction equation and the strain for 50% DRX(ε0.5) equation were solved. Accordingly, the aforementioned DRX equations were implanted into the FE model to conduct a series of simulations for the isothermal compression tests. The results show that during the evolution of DRX volume fraction at a fixed strain rate, the strain required for the same amount of DRX volume fraction increases with decreasing temperature. In contrast, at a fixed temperature, it increases with increasing strain rate. Ultimately, the DRX kinetics model of AlCu4 SiMg alloy and the consequence of the FE analysis were validated by microstructure observations.

Optimization of process parameters to maximize ultimate tensile strength of friction stir welded dissimilar aluminum alloys using response surface methodology

Aluminium alloys generally present low weldability by traditional fusion welding process. Development of the friction stir welding （FSW） has provided an alternative improved way of producing aluminium joints in a faster and reliable manner. The quality of a weld joint is stalwartly influenced by process parameter used during welding. An approach to develop a mathematical model was studied for predicting and optimizing the process parameters of dissimilar aluminum alloy （AA6351 T6-AA5083 Hlll）joints by incorporating the FSW process parameters such as tool pin profile, tool rotational speed welding speed and axial force. The effects of the FSW process parameters on the ultimate tensile strength （UTS） of friction welded dissimilar joints were discussed. Optimization was carried out to maximize the UTS using response surface methodology （RSM） and the identified optimum FSW welding parameters were reported.

Processing map and hot deformation behavior of Ta-particle reinforced TiAl composite

The hot deformation behavior of a Ta-particle reinforced TiAl composite was studied.Ti-48Al-2Cr-2Nb-0.2 W(at.%)/20 vol.%Ta metal matrix composite was fabricated by spark plasma sintering.The deformation behavior was investigated by hot compression tests at the temperature ranging from 1050 to 1200℃ and the strain rate ranging from 1×10-3 to 1 s-1.The constitutive equation containing true strain variables was established.The values of activation energy Q under different strain degrees are between 240 and 280 kJ/mol,which are lower than that of pure TiAl.Based on dynamic material modeling,the processing maps at various strain degrees were established,and the optimized parameters for hot working are 1050-1100℃ and 0.005-0.01 s-1.The microstructural evolution during deformation was characterized,which indicated that the dynamic recrystallization plays an important role in this process.

Flow behavior modeling of IMI834 titanium alloy during hot tensile deformation

A proper constitutive model was developed to predict the hot tensile flow behavior of IMI834 titanium alloy in α+β region. Hot tensile tests were performed at 800–1025 °C and 0.001–0.1 s−1. The constitutive model was developed through an Arrhenius-type equation at strains of 0.08–0.22 to characterize the hot tension behavior. It was found that the activation energies for hot tensile deformation of IMI834 titanium alloy are in the range of 519–557 kJ/mol at different strain values. The accuracy of predicted flow stress curves was evaluated using standard statistical parameters. These curves are appropriately found to be in good agreement with the experimental ones.

Molecular dynamics simulation of water transport through graphene-based nanopores: Flow behavior and structure characteristics

The flow behavior of pressure-driven water infiltration through graphene-based slit nanopores has been studied by molecular simulation.The simulated flow rate is close to the experimental values,which demonstrates the reasonability of simulation results.Water molecules can spontaneously infiltrate into the nanopores,but an external driving force is generally required to pass through the whole pores.The exit of nanopore has a large obstruction on the water effusion.The flow velocity within the graphene nanochannels does not display monotonous dependence upon the pore width,indicating that the flow is related to the microscopic structures of water confined in the nanopores.Extensive structures of confined water are characterized in order to understand the flow behavior.This simulation improves the understanding of graphene-based nanofluidics,which helps in developing a new type of membrane separation technique.

Visualization of flow behavior in ore-segregated packed beds with fine interlayers

Ore particles,especially fine interlayers,commonly segregate in heap stacking,leading to undesirable flow paths and changeable flow velocity fields of packed beds.Computed tomography(CT),COMSOL Multiphysics,and MATLAB were utilized to quantify pore structures and visualize flow behavior inside packed beds with segregated fine interlayers.The formation of fine interlayers was accompanied with the segregation of particles in packed beds.Fine particles reached the upper position of the packed beds during stacking.CT revealed that the average porosity of fine interlayers(24.21%)was significantly lower than that of the heap packed by coarse ores(37.42%),which directly affected the formation of flow paths.Specifically,the potential flow paths in the internal regions of fine interlayers were undeveloped.Fluid flowed and bypassed the fine interlayers and along the sides of the packed beds.Flow velocity also indicated that the flow paths easily gathered in the pore throat where flow velocity(1.8×10^-5 m/s)suddenly increased.Fluid stagnant regions with a flow velocity lower than 0.2×10^-5 m/s appeared in flow paths with a large diameter.

Dynamic Recrystallization Behavior of 7056 Aluminum Alloys during Hot Deformation

To investigate the dynamic recrystallization behavior of 7xxx aluminum alloys,the isothermal compression tests were carried on the 7056 aluminum alloy in the temperatures range of 320-440℃and in the strain rates range of 0.001-1 s^(-1).In addition,the microstructure of samples were observed via electron back scanning diffraction microscope.According to the results,true stress and true strain curves were established and an Arrhenius-type equation was established,showing the flow stress increases with the temperature decreasing and the strain rate increasing.The critical strain(ε_(c))and the critical stress(σ_(c))of the onset of dynamic recrystallization were identified via the strain hardening rate and constructed relationship between deformation parameters as follows:ε_(c)=6.71×10^(-4)Z^(0.1373) and σ_(p)=1.202σ_(c)+12.691.The DRX is incomplete in this alloy,whose volume fraction is only 20%even if the strain reaches 0.9.Through this study,the flow stress behavior and DRX behavior of 7056 aluminum alloys are deeply understood,which gives benefit to control the hot working process.

Characterization of hot deformation and microstructure evolution of a new metastableβtitanium alloy

The hot deformation characteristics of as-forged Ti−3.5Al−5Mo−6V−3Cr−2Sn−0.5Fe−0.1B−0.1C alloy within a temperature range from 750 to 910℃and a strain rate range from 0.001 to 1 s^(-1) were investigated by hot compression tests.The stress−strain curves show that the flow stress decreases with the increase of temperature and the decrease of strain rate.The microstructure is sensitive to deformation parameters.The dynamic recrystallization(DRX)grains appear while the temperature reaches 790℃at a constant strain rate of 0.001 s^(-1) and strain rate is not higher than 0.1 s^(-1) at a constant temperature of 910℃.The work-hardening rateθis calculated and it is found that DRX prefers to happen at high temperature and low strain rate.The constitutive equation and processing map were obtained.The average activation energy of the alloy is 242.78 kJ/mol and there are few unstable regions on the processing map,which indicates excellent hot workability.At the strain rate of 0.1 s^(-1),the stress−strain curves show an abnormal shape where there are two stress peaks simultaneously.This can be attributed to the alternation of hardening effect,which results from the continuous dynamic recrystallization(CDRX)and the rotation of DRX grains,and dynamic softening mechanism.