Influence of regenerator flow resistance on stability of pulse tube cooler

Based on the fluid network theory,the possibility of utilizing regenerator flow resistance to suppress the direct current （DC） flow induced by the introduction of a double-inlet in a pulse tube cooler is investigated theoretically. The calculation results show that increasing regenerator flow resistance can lead to a smaller extent of DC flow.Therefore,a better stability performance of the cooler can be realized.On this basis,the stability characteristics of the cooler with various regenerator matrix arrangements are studied by experiments.By replacing 30% space of 247 screens of stainless steel mesh at the cold part of the regenerator by lead balls of 0.25 mm diameter,a long-time stable temperature output at 80 K region is achieved. This achievement provides a new way to obtain stable performance for pulse tube coolers at high temperature and is helpful for its application.

旋转带肋通道流阻特性研究

With the development of aero-engines, the turbine inlet temperature continues to rise. In order to ensure the safety and reliability of the turbine blades, cooling structures must be set inside turbine blades to cool them. Heat transfer coefficient and flow resistance are the key parameters to measure the cooling characteristics of internal cooling structures. In this paper, the characteristics of flow resistance in a rotating ribbed channel is presented numerical simulation under different rib spacings, rib angles, and thermal boundary conditions. The results show that, separation and reattachment of fluid between ribs is the key effect of rib spacing on flow resistance. The flow resistance is small when the rib spacing is small, because it's difficult for the fluid to form reattachment between the ribs. With the increase of rib spacing, the reattachment phenomenon is more obvious and the flow resistance increases accordingly. In general,p: e=10 channel has the maximum flow resistance. Secondary flow caused by the ribs is the key factor affecting the flow resistance characteristics with different rib angles. The secondary flow interacts with the main flow and causes flow loss through mixing, thus affecting the flow resistance of the channel. Under static condition, the flow resistance of 60°ribbed channel is the largest. The flow resistance of channel was affected by the temperature rise ratio also. And with the increase of the Ro, the temperature rise ratio has a more obvious effect on the flow resistance of the ribbed channel.When Ro=0.45, the flow resistance of the channel with a temperature rise ratio of 0.4 is 2.4 times that of the channel without temperature rise, while when Ro=0.3, it is 1.6 times, and when Ro=0.15, it is 1.2 times.

Flow resistance and its prediction methods in compound channels

A series of experiments was carried out in a large symmetric compound channel composed of a rough main channel and rough floodplains to investigate the resistance characteristics of inbank and overbank flows. The effective Manning, Darcy-Weisbach, Chezy coefficients and the relative Nikuradse roughness height were analyzed. Many different representative methods for predicting the composite roughness were systematically summarized. Besides the measured data, a vast number of laboratory data and field data for compound channels were collected and used to check the validity of these methods for different subsection divisions including the vertical, horizontal, diagonal and bisectional divisions. The computation showed that these methods resulted in big errors in assessing the composite roughness in compound channels, and the reasons were analyzed in detail. The error magnitude is related to the subsection divisions.

Flow-resistance analysis of nano-confined fluids inspired from liquid nano-lubrication:A review

How to reduce flow resistance of nano-confined fluids to achieve a high flux is a new challenge for modern chemical engineering applications, such as membrane separation and nanofluidic devices. Traditional models are inapplicable to explain the significant differences in the flow resistance of different liquid–solid systems.On the other hand, friction reduction in liquid nano-lubrication has received considerable attention during the past decades. Both fields are exposed to a common scientific issue regarding friction reduction during liquid–solid relative motion at nanoscale. A promising approach to control the flow resistance of nano-confined fluids is to reference the factors affecting liquid nano-lubrication. In this review, two concepts of the friction coefficient derived from fluid flow and tribology were discussed to reveal their intrinsic relations. Recent progress on low or ultra-low friction coefficients in liquid nano-lubrication was summarized based on two situations. Finally, a new strategy was introduced to study the friction coefficient based on analyzing the intermolecular interactions through an atomic force microscope(AFM), which is a cutting-point to build a new model to study flowresistance at nanoscale.

Analytical determination of flow resistance characteristic for combination channel inside hydraulic manifold block

Computational fluid dynamics(CFD)was used in conjunction with BP neural network to study theflow resistance characteristic of the combination-channel inside hydraulic manifold block(HMB).The in-put parameters of the combination-channel model were confirmed to have effect on the pressure-drop bythe numerical method,and a BP neural network model was accordingly constructed to predict the channelpressure-drops.The flow resistance characteristic curves of various channels were achieved,and a perfor-mance parameter was given to evaluate the through-flow characteristic of the channel according to thecurves.The predictions are' in agreement with the numerical computation,indicating that the method canbe utilized to accurately determine the flow characteristic of the combination channel with high efficiency.

Effects of simulated submerged and rigid vegetation and grain roughness on hydraulic resistance to simulated overland flow

Better understanding of the role of vegetation and soil on hydraulic resistance of overland flow requires quantitative partition of their interaction. In this paper, a total of 144 hydraulic flume experiments were carried out to investigate the hydraulic characteristics of overland flow. Results show that hydraulic resistance is negatively correlated with Reynolds number on non-simulated vegetated slopes, while positively on vegetated slopes. The law of composite resistance agrees with the dominant resistance, depending on simulated vegetation stem,surface roughness, and discharge. Surface roughness has greater influence on overland flow resistance than vegetation stem when unit discharge is lower than the low-limited critical discharge, while vegetation has a more obvious influence when unit discharge is higher than the upper-limited critical discharge. Combined effects of simulated vegetation and surface roughness are unequal to the sum of the individual effects through t-test, implying the limitation of using linear superposition principle in calculating overland flow resistances under combined effect of roughness elements.

A proposed surface resistance model for the Penman-Monteith formula to estimate evapotranspiration in a solar greenhouse

Greenhousing is a technique to bridge season gap in vegetable production and has been widely used worldwide. Calculation of water requirement of crops grown in greenhouse and determination of their irrigation schedules in arid and semi-arid regions are essential for greenhouse maintenance and have thus attracted increased attention over the past decades. The most common method used in the literature to estimate crop evapotranspiration（ET） is the Penman-Monteith（PM） formula. When applied to greenhouse, however, it often uses canopy resistance instead of surface resistance. It is understood that the surface resistance in greenhouse is the result of a combined effect of canopy restriction and soil-surface restriction to water vapor flow, and the relative dominance of one restriction over another depends on crop canopy. In this paper, we developed a surface resistance model in a way similar to two parallel resistances in an electrical circuit to account for both restrictions. Also, considering that wind speed in greenhouse is normally rather small, we compared three methods available in the literature to calculate the aerodynamic resistance, which are the r_a^1 method proposed by Perrier（1975a, b）, the r_a^2 method proposed by Thom and Oliver（1977）, and the r_a^3 method proposed by Zhang and Lemeu（1992）. We validated the model against ET of tomatoes in a greenhouse measured from sap flow system combined with micro-lysimeter in 2015 and with weighing lysimeter in 2016. The results showed that the proposed surface resistance model improved the accuracy of the PM model, especially when the leaf area index was low and the greenhouse was being irrigated. We also found that the aerodynamic resistance calculated from the r_a^1 and r_a^3 methods is applicable to the greenhouse although the latter is slightly more accurate than the former. The proposed surface resistance model, together with the r_a^3 method for aerodynamic resistance, offers an improved approach to estimate ET in greenhouse using the PM formula.

Simplified Calculation of Flow Resistance of Suspension Bridge Main Cable Dehumidification System

To calculate the flow resistance of a main cable dehumidification system,this study considers the air flow in the main cable as the flow in a porous medium,and adopts the Hagen–Poiseuille equation by using average hydraulic radius and capillary bundle models.A mathematical derivation is combined with an experimental study to obtain a semi-empirical flow resistance formula.Additionally,Fluent software is used to simulate the flow resistance across the main cable relative to the experimental values.Based on the actual measured results for a Yangtze River bridge,this study verifies the semi-empirical formula,and indicates that it can be applied in actual engineering.

Sedimentation motion of sand particles in moving water(Ⅰ):The resistance on a small sphere moving in non-uniform flow

In hydraulics,when we deal with the problem of sand particles moving relative to the surrounding water,Stokes'formula of resistance has usually been used to render the velocity of sedimentation of the particles.But such an approach has not been proved rigorously,and its accuracy must be carefully considered.In this paper,we discuss the problem of a sphere moving in a non-uniform flow field,on the basis of the fundamental theory of hydrodynamics.We introduce two assumptions:i)the diameter of the sphere is much smaller than the linear dimension of the flow field,and ii)the velocity of the sphere relative to the surrounding water is very small.Using these two assumptions,we solve the linearized Navier-Stokes equations and equations of continuity by the method of Laplace transform,and finally we obtain a formula for the resistance acting on a sphere moving in a non-uniform flow field.

Experimental study and theoretical analysis of fluid resistance in porous media of glass spheres

Porous media have a wide range of applications in production and life, as well as in science and technology. The study of flow resistance in porous media has a great effect on industrial and agricultural production. The flow resistance of fluid flow through a 20-mm glass sphere bed is studied experimentally. It is found that there is a significant deviation between the Ergun equation and the experimental data. A staggered pore-throat model is established to investigate the flow resistance in randomly packed porous media. A hypothesis is made that the particles are staggered in a regular triangle arrangement. An analytical formulation of the flow resistance in random porous media is derived. There are no empirical constants in the formulation and every parameter has a specific physical meaning. The formulation predictions are in good agreement with the experimental data. The deviation is within the range of 25%. This shows that the staggered pore-throat model is reasonable and is expected to be verified by more experiments and extended to other porous media.

The Elaboration of Flow Resistance Model for a Bag Filter Serving a 200 MW Power Plant

On the basis of a macro flow resistance method and the Darcy Theory,a mathematical model is elaborated to characterize the flow resistance of a bag filter serving a coal-fired power plant.The development of the theoretical model is supported through acquisition of relevant data obtained by scanning the micro structure of the bag filter by means of an electron microscope.The influence of the running time and boiler load on the flow resistance and the impact of the flow resistance on the efficiency of the induced draft fan are analyzed by comparing the results of on-site operation tests.We show that the initial operation time and the table operation time are linearly related to the flow resistance of the bag filter;with the increase of boiler load,the flow resistance of the bag filter rises approximately as a quadratic function;with the rise of resistance,the power consumption of the induced draft fan increases while the efficiency of the induced draft fan decreases.

旋转条件下基于相似理论U形通道流动阻力研究

In this paper,the numerical simulation method is used to study the flow resistance law of u-shaped channels under rotating conditions based on similarity theory.The study compares three geometric models:real model,completely similar model and incompletely similar model for cooling typical U-shaped channels inside turbine rotating blades.The completely similar model is geometrically 4.8 times magnification of the real model,and the rotation radius ratio of the real model is 5.4 times that of the incomplete similar model.It is found that the friction factor of the completely similar model increases with the rotation number,and the difference varies from 6%to 38%.The friction factor of the model after incomplete similarity amplification decreases with the increase of rotation number,and the difference varies from-2%to-30%.The friction factor of the laboratory imperfectly similar amplification model combined the effects of the above two laws,and the predicted difference was within 12%.This study provides a theoretical basis for subsequent experiments related to flow resistance.

Flow resistance in the channel-bar landscape of large alluvial rivers

Accurate approaches for estimating flow resistance in large alluvial rivers are fundamental for simulating discharge,sediment transport,and flood routing.However,methods for estimating riverbed resistance and additional resistance in the channel-bar landscapes remain poorly investigated.In this study,we used in situ river bathymetry,sediment,and hydraulic data from the Shashi Reach in the Yangtze River to develop a semi-empirical approach for calculating flow resistance.Our method quantitatively separates flow resistance into riverbed resistance and additional resistance and shows high accuracy in terms of deviation ratio(~20%),root-mean-square error(~0.008),and geometric standard deviation(~3).Additional resistance plays a dominant role under low-flow conditions but a secondary role under high flows,primarily due to the reduction in momentum exchange in channel-bar regions as discharge increases.Riverbed resistance first decreases and then increases,which might be attributed to bedform changes in the lower and transitional flow regimes as flow velocity increases.Overall,our findings further the understanding of dynamic changes in flow resistance in the channel-bar landscapes of large river systems and have important implications for riverine ecology and flood management.

Solid-phase sintering process and forced convective heat transfer performance of porous-structured micro-channels

A solid-phase sintering process for the low-cost fabrication of composite micro-channels was developed. Three kinds of composite micro-channels with metallic porous structures were designed. The sintering process was studied and optimized to obtain porous-structured micro-channels with high porosity. The flow resistance and heat transfer performance in the composite micro-channels were investigated. The composite micro-channels show acceptable flow resistance, significant enhancement of heat transfer and dramatic improvement of flow boiling stability, which indicates a promising prospect for the application in forced convective heat transfer.

Theoretical Analysis and Experimental Verification on Valve-less Piezoelectric Pump with Hemisphere-segment Bluff-body

Existing researches on no-moving part valves in valve-less piezoelectric pumps mainly concentrate on pipeline valves and chamber bottom valves, which leads to the complex structure and manufacturing process of pump channel and chamber bottom. Furthermore, position fixed valves with respect to the inlet and outlet also makes the adjustability and controllability of flow rate worse. In order to overcome these shortcomings, this paper puts forward a novel implantable structure of valve-less piezoelectric pump with hemisphere-segments in the pump chamber. Based on the theory of flow around bluff-body, the flow resistance on the spherical and round surface of hemisphere-segment is different when fluid flows through, and the macroscopic flow resistance differences thus formed are also different. A novel valve-less piezoelectric pump with hemisphere-segment bluff-body （HSBB） is presented and designed. HSBB is the no-moving part valve. By the method of volume and momentum comparison, the stress on the bluff-body in the pump chamber is analyzed. The essential reason of unidirectional fluid pumping is expounded, and the flow rate formula is obtained. To verify the theory, a prototype is produced. By using the prototype, experimental research on the relationship between flow rate, pressure difference, voltage, and frequency has been carried out, which proves the correctness of the above theory. This prototype has six hemisphere-segments in the chamber filled with water, and the effective diameter of the piezoelectric bimorph is 30mm. The experiment result shows that the flow rate can reach 0.50 mL/s at the frequency of 6 Hz and the voltage of 110 V. Besides, the pressure difference can reach 26.2 mm H20 at the frequency of 6 Hz and the voltage of 160 V. This research proposes a valve-less piezoelectric pump with hemisphere-segment bluff-body, and its validity and feasibility is verified through theoretical analysis and experiment.

Numerical investigation on flow process of liquid metals in melt delivery nozzle during gas atomization process for fine metal powder production

Based on volume of fluid(VoF)interface capturing method and shear-stress transport(SST)k-ω turbulence model,numerical simulation was performed to reveal the flow mechanism of metal melts in melt delivery nozzle(MDN)during gas atomization(GA)process.The experimental validation indicated that the numerical models could give a reasonable prediction on the melt flow process in the MDN.With the decrease of the MDN inner-diameter,the melt flow resistance increased for both molten aluminum and iron,especially achieving an order of 10^(2) kPa in the case of the MDN inner-diameter≤1 mm.Based on the conventional GA process,the positive pressure was imposed on the viscous aluminum alloy melt to overcome its flow resistance in the MDN,thus producing powders under different MDN inner-diameters.When the MDN inner-diameter was reduced from 4 to 2 mm,the yield of fine powder(<150μm)soared from 54.7%to 94.2%.The surface quality of powders has also been improved when using a smaller inner-diameter MDN.

Bionic Design and Finite Element Analysis of Elbow in Ice Transportation Cooling System

With the increase in mining depth, mine heat harm has appeared to be more prominent. The mine heat harm could be resolvedor reduced by ice refrigeration. Thus, ice transportation through pipeline becomes a critical problem; typically flowresistance occurs in the elbow. In the present study, according to the analysis of the surface morphology of fish scale, abiomimetic functional surface structure for the interior wall of elbow is designed. Based on the theory of liquid-solid two phaseflow, a CFD numerical simulation of ice-water mixture flowing through the elbow is carried out using finite element method.Conventional experiments of pressure drop and flow resistance for both bionic and common elbows are conducted to test theeffect of the bionic elbow on flow resistance reduction. It is found that with the increase in the ice mass fraction in the ice-watermixture, the effect of bionic elbow on resistance reduction becomes more obvious.

Characterizing pressure fluctuation into single-loop oscillating heat pipe

The pressure characteristics inside single loop oscillating heat pipe （OHP） having 4.5 mm inner diameter copper tube with the loop height of 440 mm were addressed. Distilled water was used as working fluid inside the OHP with different filling ratios of 40%, 60% and 80% of total inside volume. Experimental results show that the thermal characteristics are significantly inter-related with pressure fluctuations as well as pressure frequency. And the pressure frequency also depends upon the evaporator temperature that is maintained in the range of 60-96 ℃. Piezoresistive absolute pressure sensor （Model-Kistler 4045A5） was used to take data. The investigation shows that the filling ratio of 60% gives the highest inside pressure magnitude at maximum number of pressure frequency at any of set evaporator temperature and the lowest heat flow resistance is achieved at 60% filling ratio.

Wave Run-up on A Coaxial Perforated Circular Cylinder

This paper describes a plane regular wave interaction with a combined cylinder which consists of a solid inner column and a coaxial perforated outer cylinder. The outer perforated surface is a thin porous cylinder with an annular gap between it and the inner cylinder. The non-linear boundary condition at the perforated wall is a prime focus in the study; energy dissipation at the perforated wall occurs through the resistance to the fluid across the perforated wall. Explicit analytical formulae are presented to calculate the wave run-up on the outer and inner surfaces of the perforated cylinder and the surface of the inner column. The theoretical results of the wave run-up are compared with previous experimental data. Numerical results have also been obtained： when the ratio of the annular gap between the two cylinders to incident wavelength （b-a）/L≤0. 1, the wave run-up on the inner surface of the perforated cylinder and the surface of inner column can partially or completely exceed the incident wave height.

Experimental study on performance of flow & desulfurisation of a gas-liquid screen scrubber for wet flue gas desulfurization

In the paper, the gas-liquid two-phase flow performance and desulfurisation performance of the gas-liquid screen scrubber were experimentally studied when limestone was used as absorbent. Experiments were carried out at varying the flue gas velocity and slurry flux in concurrent and countercurrent tower respectively. The experimental results showed that the flow resistance of absorber increased rapidly with an increase of the flue gas velocity whether in concurrent or in countereurrent tower, and the up trend of the flow resistance in the cotmtercurrent tower was higher than those in the concurrent one. The influence of the flue gas velocity on the flow resistance of absorber was more than those of the slurry flux density. Whether in the concurrent tower or in the cotmtercurrent one, increasing the flue gas velocity or the slurry flux density would enhance the desulphurization efficiency. The influence of the slurry flux density on the desulfurisation efficiency was greater than those of the flue gas velocity.