Numerical Investigation on Fluid Structure Interaction Considering Rotor Deformation for a Centrifugal Pump

The existing research for unsteady flow field and the corresponding flow induced vibration analysis of centrifugal pump are mainly carried out respectively without considering the interaction between fluid and structure. The ignorance of fluid structure interaction （FSI） means that the energy transfer between fluid and structure is neglected. To some extent, the accuracy and reliability of unsteady flow and rotor deflection analysis should be affected by this interaction mechanism. In this paper, a combined calculation between two executables for turbulent flow and vibrating structure was established using two-way coupling method to study the effect of FSI. Pressure distributions, radial forces, rotor deflection and equivalent stress are analyzed. The results show that the FSI effect to pressure distribution in flow field is complex. The pressure distribution is affected not only around impeller outlet where different variation trends of pressure values with and without FSI appear according to different relative positions between blade and cutwater, but also in the diffusion section of volute. Variation trends of peak values of radial force amplitude calculated with and without FSI are nearly same under high flow rate and designed conditions while the peak value with FSI is slightly smaller, and differently, the peak value with FSI is larger with low flow rate. In addition, the effect of FSI on the angle of radial force is quite complex, especially under 0.5Q condition. Fluctuation of radial deflection of the rotor has obvious four periods, of which the extent is relatively small under design condition and is relatively large under off-design condition. Finally, fluctuations of equivalent stress with time are obvious under different conditions, and stress value is small. The proposed research establishes the FSI calculation method for centrifugal pump analysis, and ensures the existing affect by fluid structure interaction.

Fluid structure interaction for circulation valve of hydraulic shock absorber

Based on the working principle and the damping characteristic of hydraulic shock absorber, a fluid structure interaction method was presented, which was used to analyze the microcosmic and high-frequency processing mechanism of fluid structure interaction between circulation valve and liquid of hydraulic shock absorber. The fluid mesh distortion was controlled by the CEL language, and the fluid struc^tre interaction mathematical model was established. The finite element model was established by ANSYS CFX software and was analyzed by dynamic mesh technique. The local sensitive computational area was meshed by prismatic grid, which could reduce the negative volume problem during the simulation. The circulation valve and liquid of hydraulic shock absorber were simulated and analyzed under the condition of sinusoidal inlet velocity loads. Flow characteristic and dynamics characteristic were obtained. The pressure distribution and the displacement of circulation value were obtained, and the acceleration curve of circulation valve was simulated and analyzed. The conformity of the final simulation results with the experimental datum indicates that this method is accurate and reliable to analyze the dynamics characteristic between circulation valve and liquid of hydraulic shock absorber, which can provide a theoretical foundation for optimizing hydraulic shock absorber in the future.

Channel Stability Analysis by One-Way Fluid Structure Interaction: A Case Study in China

Channel engineering stability with underground goafs is a complex three-dimensional problem, especially when considering channel leakage, and is influenced by a number of processes, such as seepage, fluid structure interaction (FSI), modeling, and selection of geological mechanical parameters. In this study, stability finite element analysis by one-way FSI was performed by establishing an integrated 3D engineering geological model. The extended Fourier amplitude sensitivity test was used to quantitatively assess the first-order and total sensitivities of the engineering model to critical geological mechanical parameters. Results illustrate that the channel engineering deformation is under a reasonable range and the elastic modulus is the highest total sensitivity parameter for the channel tilt and curvature at 0.7395 and 0.7525, respectively. Moreover, the most observable coupling effects for the curvature and horizontal strain are cohesion (0.1933) and density (0.7410), respectively. © 2017, Tianjin University and Springer-Verlag GmbH Germany.

Unstructured Grid Immersed Boundary Method for Numerical Simulation of Fluid Structure Interaction

This paper presents an improved unstructured grid immersed boundary method.The advantages of both immersed boundary method and body fitted grids which are generated by unstructured grid technology are used to enhance the computation efficiency of fluid structure interaction in complex domain.The Navier-Stokes equation was discretized spacially with collocated finite volume method and Euler implicit method in time domain.The rigid body motion was simulated by immersed boundary method in which the fluid and rigid body interface interaction was dealt with VOS(volume of solid) method.A new VOS calculation method based on graph was presented in which both immersed boundary points and cross points were collected in arbitrary order to form a graph.The method is verified with flow past oscillating cylinder.

Coupling simulation of fluid structure interaction in the stirred vessel with a pitched blade turbine

The interaction between fluid and a down-pumping pitched blade turbine fixed with a flexible shaft in the stirred vessel, as a typical fluid structure interaction phenomenon, was simulated by coupling the Computational Fluid Dynamics and Computational Structural Dynamics. Based on the verification of the simulated impeller torque and dimensionless shaft bending moment with experimental result, the dimensionless shaft bending moment and various loads acting on impeller(including lateral force, axial force and bending moment) were discussed in detail. By separating and extracting the fluid and structural components from those loads, the results show that the shaft bending moment mainly results from the lateral force on impeller although the axial force on impeller is much larger. The impeller mass imbalance increases the shaft bending moment and the lateral force on impeller, but has little influence on the axial force and bending moment acting on impeller. The dominant frequencies of impeller forces are macro-frequency, speed frequency and blade passing frequency, and are associated with the impeller mass imbalance.

Resonance mechanism of flapping wing based on fluid structure interaction simulation

Certain insect species have been observed to exploit the resonance mechanism of their wings.In order to achieve resonance and optimize aerodynamic performance,the conventional approach is to set the flapping frequency of flexible wings based on the Traditional Structural Modal(TSM)analysis.However,there exists controversy among researchers regarding the relationship between frequency and aerodynamic performance.Recognizing that the structural response of wings can be influenced by the surrounding air vibrations,an analysis known as Acoustic Structure Interaction Modal(ASIM)is introduced to calculate the resonant frequency.In this study,Fluid Structure Interaction(FSI)simulations are employed to investigate the aerodynamic performance of flapping wings at modal frequencies derived from both TSM and ASIM analyses.The performance is evaluated for various mass ratios and frequency ratios,and the findings indicate that the deformation and changes in vortex structure exhibit similarities at mass ratios that yield the highest aerodynamic performance.Notably,the flapping frequency associated with the maximum time-averaged vertical force coefficient at each mass ratio closely aligns with the ASIM frequency,as does the frequency corresponding to maximum efficiency.Thus,the ASIM analysis can provide an effective means for predicting the optimal flapping frequency for flexible wings.Furthermore,it enables the prediction that flexible wings with varying mass ratios will exhibit similar deformation and vortex structure changes.This paper offers a fresh perspective on the ongoing debate concerning the resonance mechanism of Flexible Flapping Wings(FFWs)and proposes an effective methodology for predicting their aerodynamic performance.

Fluid structure interaction of supersonic parachute with material failure

The material damage of parachute may occur in parachutes at high speeds,and the growth of tearing may finally lead to failure of aerospace mission.In order to study the damage mechanism of parachute,a material failure model is proposed to simulate the failure of canopy fabric.The inflation process of supersonic parachute is studied numerically based on Arbitrary Lagrange Euler(ALE)method.The ALE method with material failure can predict the transient parachute shape with damage propagation as well as the flow characteristics in the parachute inflation process,and the simulated dynamic opening load is consistent with the flight test.The damage propagation mechanism of parachute is then investigated,and the effect of parachute velocity on the damage process is discussed.The results show that the canopy tears apart by the fast flow from the initial damaged area and the damaged canopy shape leads to the asymmetric change of the flow structure.With the increase of Mach number,the canopy tearing speed increases,and the tearing directions become uncertain at high Mach numbers.The dynamic load when damage occurs increases with the Mach number,and is proportional to the dynamic pressure above the critical Mach number.

VIBRATION NUMERICAL ANALYSIS OF COUNTER-ROTATING TURBINE WITH WAKE-FLOW USING FLUID-STRUCTURE INTERACTION METHOD

The design of counter-rotating turbine is one of new techniques to improve the thrust-weight ratio of jet propulsion engines.Numerical analysis of a low pressure（LP）counter-rotating turbine rotor blade is presented by using ANSYS/CFX software.Interaction of aerodynamics and solid mechanics coupling in the computation is applied.In some rating of turbine,stress distribution and vibration characteristics of low pressure turbine（LPT）blade are computed.The wake aerodynamic forces and LPT blade vibration are transformed in frequency domain using fast Fourier transform（FFT）method.The results show that under wake aerodynamic force excitation,the first order modal vibration is more easily aroused and the higher order response cannot be ignored.Moreover,with different temperature fields,the vibration responses of blade are also different.

Dynamic Analysis of Tension Leg Platform for Offshore Wind Turbine Support as Fluid-Structure Interaction

Tension leg platform （TLP） for offshore wind turbine support is a new type structure in wind energy utilization. The strong-interaction method is used in analyzing the coupled model, and the dynamic characteristics of the TLP for offshore wind turbine support are recognized. As shown by the calculated results： for the lower modes, the shapes are water＇s vibration, and the vibration of water induces the structure＇s swing; the mode shapes of the structure are complex, and can largely change among different members; the mode shapes of the platform are related to the tower＇s. The frequencies of the structure do not change much after adjusting the length of the tension cables and the depth of the platform; the TLP has good adaptability for the water depths and the environment loads. The change of the size and parameters of TLP can improve the dynamic characteristics, which can reduce the vibration of the TLP caused by the loads. Through the vibration analysis, the natural vibration frequencies of TLP can be distinguished from the frequencies of condition loads, and thus the resonance vibration can be avoided, therefore the offshore wind turbine can work normally in the complex conditions.

Three-dimensional numerical simulation of a vertical axis tidal turbine using the two-way fluid structure interaction approach

The objective of this study was to develop, as well as validate the strongly coupled method (two-way fluid structural interaction (FSI)) used to simulate the transient FSI response of the vertical axis tidal turbine (VATT) rotor, subjected to spatially varying inflow. Moreover, this study examined strategies on improving techniques used for mesh deformation that account for large displacement or deformation calculations. The blade's deformation for each new time step is considered in transient two-way FSI analysis, to make the design more reliable. Usually this is not considered in routine one-way FSI simulations. A rotor with four blades and 4-m diameter was modeled and numerically analyzed. We observed that two-way FSI, utilizing the strongly coupled method, was impossible for a complex model; and thereby using ANSYS-CFX and ANSYS-MECHANICAL in work bench, as given in ANSYS-WORKBENCH, helped case examples 22 and 23, by giving an error when the solution was run. To make the method possible and reduce the computational power, a novel technique was used to transfer the file in ANSYS-APDL to obtain the solution and results. Consequently, the results indicating a two-way transient FSI analysis is a time- and resource-consuming job, but with our proposed technique we can reduce the computational time. The ANSYS STRUCTURAL results also uncover that stresses and deformations have higher values for two-way FSI as compared to one-way FSI. Similarly, fluid flow CFX results for two-way FSI are closer to experimental results as compared to one-way simulation results. Additionally, this study shows that, using the proposed method we can perform coupled simulation with simple multi-node PCs (core i5).

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian-Eulerian(ALE)approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation.A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished.In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact,a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces.In addition,the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method.Based on this method,fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained.Numerical results such as maximum Root Mean Square(RMS)drag,general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results.This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.

Hydro-elastic computational analysis of a marine propeller using two-way fluid structure interaction

Marine propellers have complex geometry and their performance is determined by costly and time consuming open water experiments.Use of numerical techniques helps researchers in effective design of propellers.Several approaches are used that predicted either hydrodynamic and acoustic response or structural response.Two-way fluid-structure interaction(FSI)analysis is a very useful approach providing all three responses which helps in the design,analysis and optimization of a propeller.The objective of this paper is to predict the hydro-elastic response of a propeller using two-way FSI on a 0.2m diameter,DTMB-4119 propeller using ANSYS software.Two-way FSI analysis is carried out using system coupling approach that transfers the data between the structural and fluid solvers.The turbulence effects are captured using the large-eddy simulation(LES)model and the Ffowcs Williams Hawkings(FWH)acoustic model is used for evaluating the sound pressure level(SPL)generated by propeller.Analysis is extended to evaluate the hydro-elastic and acoustic response of the propeller after validating the hydrodynamic performance with the experimental result in the literature.The results from Two-way FSI analysis are in close agreement when compared with the one-way FSI analysis.Two-way FSI can accommodate the peak value of stress and deformation developed during the initial part of the transient solution which is important in the design of propeller.This study reveals that metallic(NAB)propeller can be replaced by a composite propeller.The acoustic response from two-way FSI analysis will be more realistic due to the consideration of hydro-elastic effect of propeller.

The deformation characteristics and flow field around knotless polyethylene netting based on fluid structure interaction(FSI)one-way coupling

Knotless polyethylene(PE)netting is widely used in fisheries because of its excellent hydrodynamic performance and low cost.Netting deformation and the surrounding flow field distribution play an important role in determining the hydrodynamic characteristics of netting in moving water.In order to investigate the effect of solidity ratio and attack angle on drag,netting deformation,and flow field distribution through the netting,a fluid-structure interaction(FSI)model based on a one-way coupling combining the shear stress turbulent(SST)k-omega model and the large deformation nonlinear structural finite element model was evaluated.Our results showed the difference between the parallel and normal drag forces found in the present numerical model and experimental flume tank data were 9.17%and 11.58%,respectively.The mean relative error in the inclined hydrodynamic drag for different flow velocities and attack angles was 8.35%,6.69%,and 5.37%for the nettings 1,2,and 3,respectively.These results show that the present numerical simulation based on FSI one-way coupling can be used to examine hydrodynamic forces on netting.The flow simulation results show that there is a noticeable flow velocity decrease through the netting and a rather large velocity reduction region downstream from the netting for different attack angles.These results reveal the existence of turbulent flow due to the netting wake.It was found that the equivalent stress and total deformation increase as the flow velocity increases and solidity ratio decreases.

The analysis of flow characteristics in multi-channel heat meter based on fluid structure model

In this paper, a fluid structure interaction（FSI） model is used to study the internal flow field and the measurement performance of a multi-channel flow meter. The RNG k- ε turbulent model and the finite element model are used separately in the fluid domain and the structure domain to obtain the meter factor K and the deformation of the structure. The meter factor K of the flow meter is obtained through the FSI model at temperatures of 20 ℃, 50 ℃ and 80 ℃. The calculated results show the thermo expansion of the structure can significantly influence the measurement performance of the flow meter. The meter factor of the flow meter is also measured experimentally, and the comparison between the experimental results and the calculated results shows the validity of the fluid-structure interaction model. In order to reduce the measurement error, the meter factor K should be modified as the water temperature changes.

Fluid Structure Interaction Problems:the Necessity of a Well Posed,Stable and Accurate Formulation

We investigate problems of fluid structure interaction type and aim for a formulation that leads to a well posed problem and a stable numerical procedure.Our first objective is to investigate if the generally accepted formulations of the fluid structure interaction problem are the only possible ones.Our second objective is to derive a stable numerical coupling.To accomplish that we will use a weak coupling procedure and employ summation-by-parts operators and penalty terms.We compare the weak coupling with other common procedures.We also study the effect of high order accurate schemes.In multiple dimensions this is a formidable task and we start by investigating the simplest possible model problem available.As a flow model we use the linearized Euler equations in one dimension and as the structure model we consider a spring.

Fluid-Structure Interaction Analysis for Drug Transport in a Curved Stenotic Right Coronary Artery

A blockage of blood vessels resulting from thrombus or plaque deposit causes serious cardiovascular diseases. This study developed a computational model of blood flow and drug transport to investigate the effectiveness of drug delivery to the stenotic sites. A three-dimensional (3D) model of the curved stenotic right coronary artery (RCA) was reconstructed based on the clinical angiogram image. Then, blood flow and drug transport with the flexible RCA wall were simulated using the fluid structure interaction (FSI) analysis and compared with the rigid RCA wall. Results showed that the maximal total displacement and von Mises stress of the flexible RCA model are 2.14 mm and 92.06 kPa. In addition, the effective injecting time point for the best performance of drug delivery was found to be between 0 s and 0.15 s (i.e., the fluid acceleration region) for both rigid and flexible RCA models. However, there was no notable difference in the ratio of particle deposition to the stenotic areas between the rigid and flexible RCA models. This study will be significantly useful to the design of a drug delivery system for the treatment of the stenotic arteries by targeting drugs selectively to the stenotic sites.

Fluid−Structure Interaction of Two-Phase Flow Passing Through 90° Pipe Bend Under Slug Pattern Conditions

Numerical simulations of evolution characteristics of slug flow across a 90°pipe bend have been carried out to study the fluid−structure interaction response induced by internal slug flow.The two-phase flow patterns and turbulence were modelled by using the volume of fluid(VOF)model and the Realizable k−εturbulence model respectively.Firstly,validation of the CFD model was carried out and the desirable results were obtained.The different flow patterns and the time-average mean void fraction was coincident with the reported experimental data.Simulations of different cases of slug flow have been carried out to show the effects of superficial gas and liquid velocity on the evolution characteristics of slug flow.Then,a one-way coupled fluid-structure interaction framework was established to investigate the slug flow interaction with a 90°pipe bend under various superficial liquid and gas velocities.It was found that the maximum total deformation and equivalent stress increased with the increasing superficial gas velocity,while decreased with the increasing superficial liquid velocity.In addition,the total deformation and equivalent stress has obvious periodic fluctuation.Furthermore,the distribution position of maximum deformation and stress was related to the evolution of slug flow.With the increasing superficial gas velocity,the maximum total deformation was mainly located at the 90°pipe bend.But as the superficial liquid velocity increases,the maximum total deformation was mainly located in the horizontal pipe section.Consequently,the slug flow with higher superficial gas velocity will induce more serious cyclical impact on the 90°pipe bend.

New high-resolution 2D seismic imaging of fluid escape structures in the Makran subduction zone,Arabian Sea

Seabed fluid escape is active in the Makran subduction zone,Arabian Sea.Based on the new highresolution 2D seismic data,acoustic blanking zones and seafloor mounds are identified.Acoustic blanking zones include three kinds of geometries:Bell-shaped,vertically columnar and tilted zones.The bellshaped blanking zone is characterized by weak and discontinuous reflections in the interior and upbending reflections on the top,interpreted as gas chimneys.Vertically columnar blanking zone is interpreted as side-imaged gas chimneys associated with focused fluid flow and topped by a seafloor anomaly expressed as a localized reflection discontinuity,which may together serve as a vent structure.Tilted acoustic blanking zone could be induced by accretionary thrust activity and rapid sedimentation surrounding slope.Seafloor mounds occur at the sites of bell-shaped acoustic blanking zone and may be associated with the material intrusion.Bottom simulating refectors(BSRs)are widely distributed and exhibit a series of characteristics including diminished amplitude,low continuity as well as local shoaling overlapping with these acoustic blanking zones.The large amount of gases dissociated from the gas hydrates migrated upwards and then arrived at the near-seafloor sediments,followed by the formation of the gas hydrates and hence the seafloor mound.

Fully Nonlinear Simulation for Fluid/Structure Impact：A Review

This paper presents a review of the work on fluid/structure impact based on inviscid and imcompressible liquid and irrotational flow. The focus is on the velocity potential theory together with boundary element method （BEM）. Fully nonlinear boundary conditions are imposed on the unknown free surface and the wetted surface of the moving body. The review includes （1） vertical and oblique water entry of a body at constant or a prescribed varying speed, as well as free fall motion, （2） liquid droplets or column impact as well as wave impact on a body, （3） similarity solution of an expanding body. It covers two dimensional （2D）, axisymmetric and three dimensional （3D） cases. Key techniques used in the numerical simulation are outlined, including mesh generation on the multivalued free surface, the stretched coordinate system for expanding domain, the auxiliary function method for decoupling the mutual dependence of the pressure and the body motion, and treatment for the jet or the thin liquid film developed during impact.

Thermal-Fluid-Structure Coupling Analysis of Flexible Corrugated Cryogenic Hose

This work presents a numerical investigation of the thermal–fluid–structure coupling behavior of the liquid natural gas(LNG)transported in the flexible corrugated cryogenic hose.A three-dimensional model of the corrugated hose structure composed of multiple layers of different materials is established and coupled with turbulent LNG flow and heat transfer models in the commercial software ANSYS Workbench.The flow transport behavior,heat transfer across the hose layers,and structural response caused by the flow are analyzed.Parametric studies are performed to evaluate the impacts of inlet flow rate and thermal conductivity of insulation material on the temperature and structural stress of the corrugated hose.The study found that,compared with a regular operating condition,higher inlet flow velocities not only suppress the heat gain of the LNG but also lower the flow-induced structural stress.The insulation layer exhibits excellent performance in maintaining the temperature at the fluid–structure interface,showing little temperature change with respect to material thermal conductivity and ambient temperature.The simulation results may contribute to the research and design of the flexible corrugated cryogenic hoses and provide guidance for safer and more efficient field operations.