Vibration analysis of fluid- structure interaction in water hammer based on transfer matrix method

In consideration of the problem that the effect of conduit structure on water hammer has been ignored in the classical theory,the Poisson coupling between the fluid and the pipeline was studied and a fourteen-equation mathematical model of fluid-structure interaction(FSI)was developed.Then,the transfer matrix method(TMM)was used to calculate the modal frequency,modal shape and frequency response.The results were compared with that in experiment to verify the correctness of the TMM and the results show that the fluid-structure coupling has a greater impact on the modal frequencies than the modal shape.Finally,the influence on the response spectrum of different damping ratios was studied and the results show that the natural frequency under different damping ratios has changed little but there is a big difference for the pressure spectrum.With the decreasing of damping ratio,the damping of the system on frequency spectrum is more and more significant and the dispersion and dissipation is more and more apparent.Therefore the appropriate damping ratio should be selected to minimize the effects of the vibration of the FSI.The results provide references for the theory research of FSI in the transient process.

RETRACTED: Nuclear Structure Study of Odd-Odd Yttrium Nuclei within Interacting-Boson Fermi-Fermion Model (IBFFM)

Short Retraction NoticeThe paper does not meet the standards of "Journal of Applied Mathematics and Physics". This article has been retracted to straighten the academic record. In making this decision the Editorial Board follows COPE's Retraction Guidelines. The aim is to promote the circulation of scientific research by offering an ideal research publication platform with due consideration of internationally accepted standards on publication ethics. The Editorial Board would like to extend its sincere apologies for any inconvenience this retraction may have caused.Editor guiding this retraction: Prof. Wen-Xiu Ma (EiC of JAMP)The full retraction notice in PDF is preceding the original paper, which is marked "RETRACTED".

Gradient structure induced simultaneous enhancement of strength and ductility in AZ31 Mg alloy with twin-twin interactions

Gradient nanostructure was introduced to enhance the strength and ductility via deformation incompatibility accommodated by geometrical necessary dislocations for most metallic materials recently.However,few intensive researches were carried out to investigate the effect of gradient structure on the deformation twin evolution and resulting performance improvements.In the present paper,we produced gradient-structured AZ31 Mg alloy with fine-grain layers,parallel twin laminates and a coarse-grain core from two upmost surfaces to the center of plate.Surprisingly,this architected Mg alloy exhibited simultaneous enhancement of strength and ductility.Subsequent microstructural observations demonstrated that abundant twin-twin interactions resulting from higher strength and multi-axial stress state could make great contributions to the increase of work-hardening capability.This was further proved by the measurement of full-field strain evolution during the plastic deformation.Such a design strategy may provide a new path for producing advanced structure materials in which the deformation twinning works as one of the dominant plasticity mechanisms.

Influence of Soil-Structure Interaction Models on the Dynamic Responses of An Offshore Wind Turbine Under Environmental Loads

Offshore wind turbines(OWTs) suffer wind, wave and earthquake loads. The investigation of OWTs' dynamic response under environmental loads is essential for structural safety assessment. The soil-structure interaction(SSI)significantly affects the responses of OWT under environmental loads. However, there is few systematic research about the difference in the dynamic response of different SSI models under environmental loads. In order to solve the problem, the OWT is modeled by shell element, and several SSI models are built. The wind, wave and earthquake loads are taken into account. Moreover, the dynamic response, fatigue and buckling analysis are performed by ANSYS. The results indicate that SSI cannot be ignored in the dynamic response of the OWT under wind and wave loads. The SSI can decrease the displacement response of the OWT by 19% under wind and wave loads and reduce the fatigue damage of the pile. Multi-layer SSI can strongly influence the OWT's dynamic response under wind and wave loads or earthquake-only load. The vertical earthquake load increases the dynamic response in three directions.Besides, in order to simulate real environment, multi-layer SSI, soil damping and vertical SSI must be considered to evaluate the displacement response of the OWT under wind, wave and earthquake loads. The earthquake and gravity loads can cause more obvious response of the OWT than that of only wind and wave loads. The top and bottom of the tower are prone to occur buckling.

Identifying the Spatial Structure of Black Hole and Tropical Cyclone Based on a Theoretical Analysis of Orthogonal Interaction

Black holes are recognized by Newton’s gravitational theory and Einstein’s general relativity, but there is still a lack of understanding the spatial structure of events, especially the nature of event horizon. In this paper, a theoretical analysis is used to compare the structures of tropical cyclone in the atmosphere and black hole in the astronomy so that five results are: 1) Both of them share the similar spatial structure, with tropical cyclone and black hole having the outflow cloud shield and the horizon sphere in the central part, respectively, while four spiral material bands exist in the rotating plane around them;2) In theoretically, the energy density formed by the orthogonal interaction of the four spiral material bands is as times as the total kinetic energy of the head-on interaction;3) This region of high energy density can lead to the conversion from mass to energy and the creation of new physical states of matter, which is a black hole event;4) The outer horizon of a black hole is the outermost interface of events, or the orthogonal interaction interface of particles;5) High-speed plasma jets extended at the poles of the black hole are directly associated with the shear stress of orthogonal interaction.

Dynamic Analysis of Tension Leg Platform for Offshore Wind Turbine Support as Fluid-Structure Interaction

Tension leg platform （TLP） for offshore wind turbine support is a new type structure in wind energy utilization. The strong-interaction method is used in analyzing the coupled model, and the dynamic characteristics of the TLP for offshore wind turbine support are recognized. As shown by the calculated results： for the lower modes, the shapes are water＇s vibration, and the vibration of water induces the structure＇s swing; the mode shapes of the structure are complex, and can largely change among different members; the mode shapes of the platform are related to the tower＇s. The frequencies of the structure do not change much after adjusting the length of the tension cables and the depth of the platform; the TLP has good adaptability for the water depths and the environment loads. The change of the size and parameters of TLP can improve the dynamic characteristics, which can reduce the vibration of the TLP caused by the loads. Through the vibration analysis, the natural vibration frequencies of TLP can be distinguished from the frequencies of condition loads, and thus the resonance vibration can be avoided, therefore the offshore wind turbine can work normally in the complex conditions.

Improved frequency modeling and solution for parallel liquid-filled pipes considering both fluid-structure interaction and structural coupling

The dynamic characteristics of a single liquid-filled pipe have been broadly studied in the previous literature.The parallel liquid-filled pipe(PLFP)system is also widely used in engineering,and its structure is more complex than that of a single pipe.However,there are few reports about the dynamic characteristics of the PLFPs.Therefore,this paper proposes improved frequency modeling and solution for the PLFPs,involving the logical alignment principle and coupled matrix processing.The established model incorporates both the fluid-structure interaction(FSI)and the structural coupling of the PLFPs.The validity of the established model is verified by modal experiments.The effects of some unique parameters on the dynamic characteristics of the PLFPs are discussed.This work provides a feasible method for solving the FSI of multiple pipes in parallel and potential theoretical guidance for the dynamic analysis of the PLFPs in engineering.

An improved algorithm for fluid-structure interaction of high-speed trains under crosswind

Based on the train-track coupling dynamics and high-speed train aerodynamics, this paper deals with an improved algorithm for fluid-structure interaction of high-speed trains. In the algorithm, the data communication between fluid solver and structure solver is avoided by inserting the program of train-track coupling dynamics into fluid dynamics program, and the relaxation factor concerning the load boundary of the fluid-structure interface is introduced to improve the fluctuation and convergence of aerodynamic forces. With this method, the fluid-structure dynamics of a highspeed train are simulated under the condition that the velocity of crosswind is 13.8 m/s and the train speed is 350 km/h. When the relaxation factor equals 0.5, the fluctuation of aerodynamic forces is lower and its convergence is faster than in other cases. The side force and lateral displacement of the head train are compared between off-line simulation and co-simulation. Simulation results show that the fluid-structure interaction has a significant influence on the aerodynam- ics and attitude of the head train under crosswind conditions. In addition, the security indexes of the head train worsen after the fluid-structure interaction calculation. Therefore, the fluid-structure interaction calculation is necessary for high-speed trains.

INVESTIGATION OF AIRSHIP AEROELASTICITY USING FLUID- STRUCTURE INTERACTION

Due to the flexibility of the envelope of large stratosphere airships, the aerodynamic solution of such airship is closely related to its shape and the external aerodynamic forces which lead to the structural deformation. It is essentially one of the Fluid-Structure Interaction （FSI） problems. This article aims at the numerical investigation of nonlinear airship aeroelasticity in consideration of aerodynamics and structure coupling, using an iteration method. The three-dimensional flow around the airship was numerically studied by means of the SIMPLE method based on the finite volume method. Nonlinear finite element analysis was employed for geometrically nonlinear deformation of the airship shape. Comparison of aerodynamic parameters and the pressure distribution between rigid and aeroelastic models was conducted when an airship is in a trimmed flight state in specified flight conditions. The effect ofaeroelasticity on the airship aerodynamics was detailed.

Hybrid algorithm for modeling of fluid-structure interaction in incompressible, viscous flows

The objective of this paper is to present and to validate a new hybrid coupling （HC） algorithm for modeling of fluid-structure interaction （FSI） in incompressible, viscous flows. The HC algorithm is able to avoid numerical instability issues associated with artificial added mass effects, which are often encountered by standard loosely coupled （LC） and tightly coupled （TC） algorithms, when modeling the FSI response of flexible structures in incompressible flow. The artificial added mass effect is caused by the lag in exchange of interfacial displacements and forces between the fluid and solid solvers in partitioned algorithms. The artificial added mass effect is much more prominent for light/flexible struc- tures moving in water, because the fluid forces are in the same order of magnitude as the solid forces, and because the speed at which numerical errors propagate in an incom- pressible fluid. The new HC algorithm avoids numerical instability issues associated with artificial added mass effects by embedding Theodorsen＇s analytical approximation of the hydroelastic forces in the solution process to obtain better initial estimates of the displacements. Details of the new HC algorithm are presented. Numerical validation studies are shown for the forced pitching response of a steel and a plastic hydrofoil. The results show that the HC algorithm is able to converge faster, and is able to avoid numerical insta- bility issues, compared to standard LC and TC algorithms, when modeling the transient FSI response of a plastic hydrofoil. Although the HC algorithm is only demonstrated for a NACA0009 hydrofoil subject to pure pitching motion, the method can be easily extended to model general 3-D FSI response and stability of complex, flexible structures in turbulent, incompressible, multiphase flows.

Fluid-structure interaction simulation of three-dimensional flexible hydrofoil in water tunnel

The closely coupled approach combined with the finite volume method （FVM） solver and the finite element method （FEM） solver is used to investigate the fluid-structure interaction （FSI） of a three-dimensional cantilevered hydrofoil in the water tunnel. The FVM solver and the coupled approach are verified and validated by compar- ing the numerical predictions with the experimental measurements, and good agreement is obtained concerning both the lift on the foil and the tip displacement. In the noncav- itating flow, the result indicates that the growth of the initial incidence angle and the Reynolds number improves the deformation of the foil, and the lift on the foil is increased by the twist deformation. The normalized twist angle and displacement along the span of the hydrofoil for different incidence angles and Reynolds numbers are almost uniform. For the cavitation flow, it is shown that the small amplitude vibration of the foil has limited influence on the developing process of the partial cavity, and the quasi two-dimensional cavity shedding does not change the deformation mode of the hydrofoil. However, the frequency spectrum of the lift on the foil contains the frequency which is associated with the first bend frequency of the hydrofoil.

NUMERICAL SOLUTION OF FLUID-STRUCTURE INTERACTION IN LIQUID-FILLED PIPES BY METHOD OF CHARACTERISTICS

Fluid-structure interaction （FSI） is essentially a dynamic phenomenon and always exists in fluid-filled pipe system. The four-equation model, which has been proved to be effective to describe and predict the phenomenon of FSI due to friction coupling and Poisson coupling being taken into account, is utilized to describe the FSI of fluid-filled pipe system. Terse compatibility equations are educed by the method of characteristics （MOC） to describe the fluid-filled pipe system. To shorten computing time needed to get the solutions under the condition of keeping accuracy requirement, two steps are adopted, firstly the time step Δt and divided number of the straight pipe are optimized, sec-ondly the mesh spacing Δz close to boundary is subdivided in several submeshes automatically ac-cording to the speed gradient of fluid. The mathematical model and arithmetic are validated by com-parisons between simulation solutions of two straight pipe systems and experiment known from lit-erature.

Fluid-Structure Interaction Modeling of the Living Artery: Based on the Zero-Pressure Status and the Anisotropic Hyperelastic Constitutive Model

Vascular diseases such as aneurysm,hemadostenosis,aortic dissection are the primary causes of people’s death around world.As a result,it is significant to improve our knowledge about them,which can help to treat the disease.Measuring the hemodynamic factor like the blood pressure,the wall shear stress(WSS)and the oscillatory shear index(OSI)is,however,still beyond the capabilities of in-vivo measurement techniques.So the use of mathematical models and numerical simulations for the studies of the blood flow in arteries and,in general,of the cardiovascular system,both in physiological and pathological conditions,has received an increasing attention in the biomedical community during the last two decades.Indeed,such studies aims at enhancing the current knowledge of the physiology of the cardiovascular system,as well as providing reliable tools for the medical doctors to predict the natural course of pathologies and,possibly,the occurrence of cardiovascular accidents.The computational vascular fluid-structure interaction(FSI)methodology is a numerical simulation method which is used to explain the hemodynamic factors.The WSS on the luminal wall and the mechanical stress in the vascular wall are directly related to the location of the lesion,and the blood flow strongly interacts with the vascular wall motion.The arterial wall continually adapts to the charge of its mechanical environment(due to,for example,growth,atrophy,remodelling,repair,ageing,and disease)and consequently undergoes several irreversible processes.Primary acute mechanisms of vascularFSI numerical simulation seem to be associated with(1)the arterial histology and the patient-specific complex geometry,(2)the typical mechanical properties of the layer,(3)properties of the blood is assumed as Newtonian fluid or non-Newtonian fluid based on the scale ofthe diameter of a vessel,(4)residual stress in the zero-pressure configuration.The arterial system naturally function under permanent physiological loading conditions.Fung defined the residual stress and measured the opening angle which varies greatly along the aortic tree.Consequently,most of these systems never experience a stress-free state in their’service life’,so a stress and strain fields are present in any in vivo obtained patientspecific cardiovascular geometry.The residual stress always be ignored in FSI simulation or be assumed to equal zero,and the vivo patient-specific artery geometry is assumed as zero-pressure configuration.To define the in vivo stress state of artery,an inverse problem needs to be solved:the undeformed shape of a body or its stress state in its deformed state needs to be determined given the deformed configuration and the loads causing this deformation.The modular inverse elastostatics method is used to resolve the pressure-induced stress state for in vivo imaging based on cardiovascular modeling proposed by Peirlinck.Here,we build a living vessel FSI model based on 4 key factors.In order to get the universal simulation results,we focus on idealized geometries of the vessel that represent healthy(physiological)conditions of the cerebral vasculature.Blood can be assumed as the Newtonian fluid at this scale.The anisotropic hyperelastic constitutive law(Gasser-Holzapfel-Ogden)is used in zero-pressure configuration.Afterwards,we propose the material parameters for the different constitutive models and the computational configurations.We demonstrate the importance of introducing the residual stress into vascular blood flow modeling by performing a comparing zero-pressure configuration and no-resistance configuration.We get the conclusion that the zero-pressure status model has smaller displacement and larger stress distribution compared with no-resistance stress model.Hence,the methodology presented here will be particularly useful to study the mechanobiological processes in the healthy and diseased vascular wall.

Dynamic Adaptive Finite Element Analysis of Acoustic Wave Propagation Due to Underwater Explosion for Fluid-structure Interaction Problems

在这份报纸，进附近的结构上的水和他们的效果里的远域爆炸波浪的繁殖的调查被执行。为远域结构，包围结构的液体的运动可以被假定小，允许管理液体方程的 linearization。这个问题的完全的分析必须在包围液体包含结构和爆炸波浪的繁殖的动态反应的同时的答案。在这研究，一个动态适应有限元素过程被建议。它到一个 2D 液体结构相互作用的解决方案的应用程序在时间域被调查。研究包括：一) 计算远地散布波浪由于在水下看情况时间的声学的波浪方程的爆炸包括答案， b ) 用联合 Euler-Lagrangian 途径的液体结构相互作用分析，和 c ) 适应有限元素过程采用错误估计，并且重新协调。时间的网孔改编被格子的本地新生基于压力功能的弯曲用时间依赖者错误指示物完成。作为结果，全面反应被一个动人的网孔更好比一个相等的一致网孔预言。另外，当精确性被改进时，为大问题的计算的费用被减少。

3D numerical simulation on fluid-structure interaction of structure subjected to underwater explosion with cavitation

In the underwater-shock environment, cavitation occurs near the structural surface. The dynamic response of fluid-structure interactions is influenced seriously by the cavitation effects. It is also the difficulty in the field of underwater explosion. With the traditional boundary element method and the finite element method （FEM）, it is difficult to solve the nonlinear problem with cavitation effects subjected to the underwater explosion. To solve this problem, under the consideration of the cavitation effects and fluid compressibility, with fluid viscidity being neglected, a 3D numerical model of transient nonlinear fluid-structure interaction subjected to the underwater explosion is built. The fluid spectral element method （SEM） and the FEM are adopted to solve this model. After comparison with the FEM, it is shown that the SEM is more precise than the FEM, and the SEM results are in good coincidence with benchmark results and experiment results. Based on this, combined with ABAQUS, the transient fluid-structure interaction mechanism of the 3D submerged spherical shell and ship stiffened plates subjected to the underwater explosion is discussed, and the cavitation region and its influence on the structural dynamic responses are presented. The paper aims at providing references for relevant research on transient fluid-structure interaction of ship structures subjected to the underwater explosion.

Effects of renal artery stenosis on realistic model of abdominalaorta and renal arteries incorporating fluid-structureinteraction and pulsatile non-Newtonian blood flow

The effects of the renal artery stenosis （RAS） on the blood flow and vessel walls are investigated. The pulsatile blood flow through an anatomically realistic model of the abdominal aorta and renal arteries reconstructed from CT-scan images is simulated, which incorporates the fluid-structure interaction （FSI）. In addition to the investigation of the RAS effects on the wall shear stress and the displacement of the vessel wall, it is determined that the RAS leads to decrease in the renal mass flow. This may cause the activation of the renin-angiotension system and results in severe hypertension.

Fluid-Structure Interaction Analysis of Flexible Plate with Partitioned Coupling Method

The development and rapid usage of numerical codes for fluid-structure interaction(FSI) problems are of great relevance to researchers in many engineering fields such as civil engineering and ocean engineering. This multidisciplinary field known as FSI has been expanded to engineering fields such as offshore structures, tall slender structures and other flexible structures applications. The motivation of this paper is to investigate the numerical model of two-way coupling FSI partitioned flexible plate structure under fluid flow. The adopted partitioned method and approach utilized the advantage of the existing numerical algorithms in solving the two-way coupling fluid and structural interactions. The flexible plate was subjected to a fluid flow which causes large deformation on the fluid domain from the oscillation of the flexible plate. Both fluid and flexible plate are subjected to the interaction of load transfer within two physics by using the strong and weak coupling methods of MFS and Load Transfer Physics Environment, respectively. The oscillation and deformation results have been validated which demonstrate the reliability of both strong and weak method in resolving the two-way coupling problem in contribution of knowledge to the feasibility field study of ocean engineering and civil engineering.

Numerical Simulation of ATPS Parachute Transient Dynamics Using Fluid-Structure Interaction Method

In order to simulate and analyze the dynamic characteristics of the parachute from advanced tactical parachute system(ATPS),a nonlinear finite element algorithm and a preconditioning finite volume method are employed and developed to construct three dimensional parachute fluid-structure interaction(FSI)model.Parachute fabric material is represented by membrane-cable elements,and geometrical nonlinear algorithm is employed with wrinkling technique embedded to simulate the large deformations of parachute structure by applying the NewtonRaphson iteration method.On the other hand,the time-dependent flow surrounding parachute canopy is simulated using preconditioned lower-upper symmetric Gauss-Seidel(LU-SGS)method.The pseudo solid dynamic mesh algorithm is employed to update the flow-field mesh based on the complex and arbitrary motion of parachute canopy.Due to the large amount of computation during the FSI simulation,massage passing interface(MPI)parallel computation technique is used for all those three modules to improve the performance of the FSI code.The FSI method is tested to simulate one kind of ATPS parachutes to predict the parachute configuration and anticipate the parachute descent speeds.The comparison of results between the proposed method and those in literatures demonstrates the method to be a useful tool for parachute designers.

Failure pressure calculation of fracturing well based on fluid-structure interaction

Failure pressure is a key parameter in reservoir hydrofracturing operation. Existing analytical methods for calculating the failure pressure are based on the assumption that borehole fluid is under two extreme conditions: non-infiltration or complete infiltration. The assumption is not suitable for the actual infiltration process, and this will cause a great error in practical calculation. It shows that during the injection process, the dynamic variation in effective stress-dependent permeability has an influence on the infiltration, and the influence also brings about calculation errors. Based on the fluid-structure interaction and finite element method (FEM), considering partial infiltration during injection process, a numerical model for calculating rock failure pressure is established. According to the analysis of permeability test results and response-surface method, a new variation rule of rock permeability with the change of effective stress is presented, and the relationships among the permeability, confining pressure and pore pressure are proposed. There are some differences between the dynamic value of permeability-effective-stress coefficient observed herein and the one obtained by the classical theory. Combining with the numerical model and the dynamic permeability, a coupling method for calculating failure pressure is developed. Comparison of field data and calculated values obtained by various methods shows that accurate values can be obtained by the coupling method. The coupling method can be widely applied to the calculation of failure pressure of reservoirs and complex wells to achieve effective fracturing operation.

Numerical simulation of soft palate movement and airflow in human upper airway by fluid-structure interaction method

In this paper, the authors present airflow field characteristics of human upper airway and soft palate movement attitude during breathing. On the basis of the data taken from the spiral computerized tomography images of a healthy person and a patient with Obstructive Sleep Apnea-Hypopnea Syndrome （OSAHS）, three-dimensional models of upper airway cavity and soft palate are reconstructed by the method of surface rendering. Numerical simulation is performed for airflow in the upper airway and displacement of soft palate by fluid-structure interaction analysis. The reconstructed threedimensional models precisely preserve the original configuration of upper airways and soft palate. The results of the pressure and velocity distributions in the airflow field are quantitatively determined, and the displacement of soft palate is presented. Pressure gradients of airway are lower for the healthy person and the airflow distribution is quite uniform in the case of free breathing. However, the OSAHS patient remarkably escalates both the pressure and velocity in the upper airway, and causes higher displacement of the soft palate. The present study is useful in revealing pathogenesis and quantitative mutual relationship between configuration and function of the upper airway as well as in diagnosingdiseases related to anatomical structure and function of the upper airway.