In the paper, a numerical study on symmetrical and asymmetrical laminar jet-forced flows is carried out by using a lattice Boltzmann method （LBM） with a special boundary treatment. The simulation results are in very...In the paper, a numerical study on symmetrical and asymmetrical laminar jet-forced flows is carried out by using a lattice Boltzmann method （LBM） with a special boundary treatment. The simulation results are in very good agreement with the available numerical prediction. It is shown that the LBM is a competitive method for the laminar jet-forced flow in terms of computational efficiency and stability.展开更多
In the flow on a mobile bed in an open channel, sand ripple often appears after the sediment begins to move. Different scholars have different views on the formation of sand ripples. This paper holds that as the rippl...In the flow on a mobile bed in an open channel, sand ripple often appears after the sediment begins to move. Different scholars have different views on the formation of sand ripples. This paper holds that as the ripple in general is very small, its formation is due to the instability of the laminar flow or the evolution of the small-scale coherent structures in the sublayer adjacent to the wall of the open channel. When the shear stresses caused by the disturbing waves or the coherent structure near the bed surface boundary and the water flow itself are greater than the shields stresses, responses on the bed surface appear and the sand ripple forms. If the frequency of the shear stress caused by the disturbance is close to the natural frequency of the sand grains that produced resonance, such a phenomenon is called the 'detection property' of the sediment. It is at this point that the maximum resonance appears and the sand ripple develops rapidly.展开更多
The evolution of wake structures and variation of the forces on a flat plate in harmonic oscillatory and in-line combined flows are obtained numerically by improved discrete vortex method. For the oscillatory oncoming...The evolution of wake structures and variation of the forces on a flat plate in harmonic oscillatory and in-line combined flows are obtained numerically by improved discrete vortex method. For the oscillatory oncoming flow cases, when K_c number varies from 2 to 40, the vortex pattern changes from a 'harmonic wave' shaped (in a range of small K_c numbers) to a slight inclined 'harmonic wave' shaped (in a range of moderate K_c numbers), then to inclined vortex clusters with an angle of 50 ° to the oncoming flow direction (at K_c = 20), at last, as K_c number becomes large, the vortex pattern is like a normal Karman vortex street. The well predicted drag and inertia force coefficients are obtained, which are more close to the results of Keulegan & Carpenter's experiment as compared with previous vortex simulation by other au- thors. The existence of minimum point of inertia force coefficient C_m near K_c = 20 is also well predicted and this phenomenon can be interpreted according to the vortex structure. For steady-oscillatory in-line combined flow cases, the vortex modes behave like a vortex street, exhibit a 'longitudinal wave' structure, and a vor- tex cluster shape corresponding to the ratios of U_m to U_0 which are of O (10^(-1)), O(1)and O (10), respectively. The effect on the prediction of forces on the flat plate from the disturbance component in a combined flow has been demon- strated qualitatively. In addition to this, the lock-in phenomenon of vortex shedding has been checked.展开更多
In this paper, using the integration method, it is sought to solve the problem for the laminar boundary_layer on a flat plate. At first, a trial function of the velocity profile which satisfies the basical boundary co...In this paper, using the integration method, it is sought to solve the problem for the laminar boundary_layer on a flat plate. At first, a trial function of the velocity profile which satisfies the basical boundary conditions is selected. The coefficients in the trial function awaiting decision are decided by using some numerical results of the boundary_layer differential equations. It is similar to the method proposed by Peng Yichuan, but the former is simpler. According to the method proposed by Peng, when the awaiting decision coefficients of the trial function are decided, it is sought to solve a third power algebraic equation. On the other hand, in this paper, there is only need for solving a linear algebraic equation. Moreover, the accuracy of the results of this paper is higher than that of Peng.展开更多
Various properties of a necklace vortex system formed around a rectangular plate standing vertically on a flat ground wall were investigated by visualizations produced by injecting fluorescent dye into a water channel...Various properties of a necklace vortex system formed around a rectangular plate standing vertically on a flat ground wall were investigated by visualizations produced by injecting fluorescent dye into a water channel flow. As a result, it was found that the necklace vortex pattern had three steady systems depending on the Reynolds number Reh, the relative height h/δ of the rectangular plate compared with the laminar boundary layer thickness and the aspect ratio w/h. As it is expected that the aspect ratio of the rectangular plate will typify the projected area configuration of various three-dimensional bodies, the aspect ratio is varied widely from 0.5 to 7.0. The transitional boundaries of Reh and h/δ in the 2-vortex, 4-vortex and 6-vortex systems for each aspect ratio decreased when w/h < 3.0, and increased when w/h ≥ 3.0 as w/h increased. The x-direction length of the main vortex position XV1/h was almost constant when w/h < 3.0, and decreased when w/h ≥ 3.0 as Reh increased. Then, the separation length r1/h increased when w/h < 3.0 and Reh < 1000, and became almost constant when w/h ≥ 3.0 and Reh ≥ 1000 as w/h and Reh increased. Moreover, the increase of r1/h is notably rapid when w/h < 3.0.展开更多
Flow transition from laminar to turbulent mode (and vice versa)—that is, the initiation of turbulence—is one of the most important research subjects in the history of engineering. Even for pipe flow, predicting the ...Flow transition from laminar to turbulent mode (and vice versa)—that is, the initiation of turbulence—is one of the most important research subjects in the history of engineering. Even for pipe flow, predicting the onset of turbulence requires sophisticated instrumentation and/or direct numerical simulation, based on observing the instantaneous flow structure formation and evolution. In this work, a local Reynolds number equivalence c (ratio of local inertia effect to viscous effect) is seen to conform to the Universal Law of the Wall, where c = 1 represents a quantitative balance between the abovementioned two effects. This coincides with the wall layer thickness (y+= 1, where y+ is the dimensionless distance from the wall surface defined in the Universal Law of the Wall). It is found that the characteristic of how the local derivative of c against the local velocity changes with increasing velocity determines the onset of turbulence. For pipe flow, c - 25, and for plate flow, c - 151.5. These findings suggest that a certain combination of c and velocity (nonlinearity) can qualify the source of turbulence (i.e., generate turbulent energy). Similarly, a re-evaluation of the previous findings reveals that only the geometrically narrow domain can act locally as the source of turbulence, with the rest of the flow field largely being left for transporting and dissipating. This understanding will have an impact on the future large-scale modeling of turbulence.展开更多
A design of a slot bushing with a volumetric field has been developed, which allows to produce continuous fibers from melts with difficult processing characteristics in order to produce fibers with better operating ch...A design of a slot bushing with a volumetric field has been developed, which allows to produce continuous fibers from melts with difficult processing characteristics in order to produce fibers with better operating characteristics. The operability of the design was confirmed when solving two problems of special technological complexity. 1. 400 and 800 orifice bushings for production of continuous fibers from the basalt melt have been developed and recommended for manufacture. 2. The process of production of continuous fibers from standard glass using 2400 orifice bushing with perforated plates instead of orifice tips without air cooling, has been realized for the first time.展开更多
In this paper, a detailed numerical investigation of two-dimensional laminar forced convection in a porous channel with inlet and outlet slot is presented. A uniform heat flux is applied on one wall of channel and ano...In this paper, a detailed numerical investigation of two-dimensional laminar forced convection in a porous channel with inlet and outlet slot is presented. A uniform heat flux is applied on one wall of channel and another wall is isolated. The flow in the porous medium is modeled using the Brinkman-Forchheimer-extended Darcy model in which the inertia and boundary effects are taken into consideration and thermal dispersion effects are not included in the energy equation. Parametric studies are conducted to evaluate the effects of particle diameter, Reynolds number on the heat transfer and friction factor. Nusselt number and friction factor are developed for efficient design of a porous heat exchanger based on the present configuration. In order to solve this problem Fluent software was used.展开更多
The formula of the vibration response and power flow in beam-stiffened plate with force excitation applied on.the plate, have been obtained by using the Steepest Descent Integral method. The characteristics of the pow...The formula of the vibration response and power flow in beam-stiffened plate with force excitation applied on.the plate, have been obtained by using the Steepest Descent Integral method. The characteristics of the power flow have been studied through computer simulation.It is shown that the stiffener acts as an extra lineal excitation applied on the plate and changes the characteristics of the power flow of the infinite plate greatly The greater the stiffness and the smaller the distance between the exciting point and the stiffener is, the greater the induence is. Lastly, experiments have been carried out by using the dualaccelerometer measurement technique that based on cross spectrum, and the test data agree well with the theoretical results展开更多
An analysis of the flow in the gap between a rotating cone and a stationary plate at low Reynolds numbers is presented. Using series expansions for the components of the mean velocity profile and the pressure gradient...An analysis of the flow in the gap between a rotating cone and a stationary plate at low Reynolds numbers is presented. Using series expansions for the components of the mean velocity profile and the pressure gradient the Navier-Stokes equations and the continuity equation for a Newtonian fluid written in cylindrical coordinates are solved. It is found that the solution is stable and convergent for the local Reynolds numbers Re smaller than 1.2928. The computed angle of the wall streamlines is found to be in good agreement with experimental data.展开更多
基金supported by the National Natural Science Foundation of China (No. 10771134)the Youth Science Foundation of USTC
文摘In the paper, a numerical study on symmetrical and asymmetrical laminar jet-forced flows is carried out by using a lattice Boltzmann method （LBM） with a special boundary treatment. The simulation results are in very good agreement with the available numerical prediction. It is shown that the LBM is a competitive method for the laminar jet-forced flow in terms of computational efficiency and stability.
文摘In the flow on a mobile bed in an open channel, sand ripple often appears after the sediment begins to move. Different scholars have different views on the formation of sand ripples. This paper holds that as the ripple in general is very small, its formation is due to the instability of the laminar flow or the evolution of the small-scale coherent structures in the sublayer adjacent to the wall of the open channel. When the shear stresses caused by the disturbing waves or the coherent structure near the bed surface boundary and the water flow itself are greater than the shields stresses, responses on the bed surface appear and the sand ripple forms. If the frequency of the shear stress caused by the disturbance is close to the natural frequency of the sand grains that produced resonance, such a phenomenon is called the 'detection property' of the sediment. It is at this point that the maximum resonance appears and the sand ripple develops rapidly.
基金The project supported by National Natural Science Foundation of China & LNM, Institute of Mechanics, CAS
文摘The evolution of wake structures and variation of the forces on a flat plate in harmonic oscillatory and in-line combined flows are obtained numerically by improved discrete vortex method. For the oscillatory oncoming flow cases, when K_c number varies from 2 to 40, the vortex pattern changes from a 'harmonic wave' shaped (in a range of small K_c numbers) to a slight inclined 'harmonic wave' shaped (in a range of moderate K_c numbers), then to inclined vortex clusters with an angle of 50 ° to the oncoming flow direction (at K_c = 20), at last, as K_c number becomes large, the vortex pattern is like a normal Karman vortex street. The well predicted drag and inertia force coefficients are obtained, which are more close to the results of Keulegan & Carpenter's experiment as compared with previous vortex simulation by other au- thors. The existence of minimum point of inertia force coefficient C_m near K_c = 20 is also well predicted and this phenomenon can be interpreted according to the vortex structure. For steady-oscillatory in-line combined flow cases, the vortex modes behave like a vortex street, exhibit a 'longitudinal wave' structure, and a vor- tex cluster shape corresponding to the ratios of U_m to U_0 which are of O (10^(-1)), O(1)and O (10), respectively. The effect on the prediction of forces on the flat plate from the disturbance component in a combined flow has been demon- strated qualitatively. In addition to this, the lock-in phenomenon of vortex shedding has been checked.
文摘In this paper, using the integration method, it is sought to solve the problem for the laminar boundary_layer on a flat plate. At first, a trial function of the velocity profile which satisfies the basical boundary conditions is selected. The coefficients in the trial function awaiting decision are decided by using some numerical results of the boundary_layer differential equations. It is similar to the method proposed by Peng Yichuan, but the former is simpler. According to the method proposed by Peng, when the awaiting decision coefficients of the trial function are decided, it is sought to solve a third power algebraic equation. On the other hand, in this paper, there is only need for solving a linear algebraic equation. Moreover, the accuracy of the results of this paper is higher than that of Peng.
文摘Various properties of a necklace vortex system formed around a rectangular plate standing vertically on a flat ground wall were investigated by visualizations produced by injecting fluorescent dye into a water channel flow. As a result, it was found that the necklace vortex pattern had three steady systems depending on the Reynolds number Reh, the relative height h/δ of the rectangular plate compared with the laminar boundary layer thickness and the aspect ratio w/h. As it is expected that the aspect ratio of the rectangular plate will typify the projected area configuration of various three-dimensional bodies, the aspect ratio is varied widely from 0.5 to 7.0. The transitional boundaries of Reh and h/δ in the 2-vortex, 4-vortex and 6-vortex systems for each aspect ratio decreased when w/h < 3.0, and increased when w/h ≥ 3.0 as w/h increased. The x-direction length of the main vortex position XV1/h was almost constant when w/h < 3.0, and decreased when w/h ≥ 3.0 as Reh increased. Then, the separation length r1/h increased when w/h < 3.0 and Reh < 1000, and became almost constant when w/h ≥ 3.0 and Reh ≥ 1000 as w/h and Reh increased. Moreover, the increase of r1/h is notably rapid when w/h < 3.0.
文摘Flow transition from laminar to turbulent mode (and vice versa)—that is, the initiation of turbulence—is one of the most important research subjects in the history of engineering. Even for pipe flow, predicting the onset of turbulence requires sophisticated instrumentation and/or direct numerical simulation, based on observing the instantaneous flow structure formation and evolution. In this work, a local Reynolds number equivalence c (ratio of local inertia effect to viscous effect) is seen to conform to the Universal Law of the Wall, where c = 1 represents a quantitative balance between the abovementioned two effects. This coincides with the wall layer thickness (y+= 1, where y+ is the dimensionless distance from the wall surface defined in the Universal Law of the Wall). It is found that the characteristic of how the local derivative of c against the local velocity changes with increasing velocity determines the onset of turbulence. For pipe flow, c - 25, and for plate flow, c - 151.5. These findings suggest that a certain combination of c and velocity (nonlinearity) can qualify the source of turbulence (i.e., generate turbulent energy). Similarly, a re-evaluation of the previous findings reveals that only the geometrically narrow domain can act locally as the source of turbulence, with the rest of the flow field largely being left for transporting and dissipating. This understanding will have an impact on the future large-scale modeling of turbulence.
文摘A design of a slot bushing with a volumetric field has been developed, which allows to produce continuous fibers from melts with difficult processing characteristics in order to produce fibers with better operating characteristics. The operability of the design was confirmed when solving two problems of special technological complexity. 1. 400 and 800 orifice bushings for production of continuous fibers from the basalt melt have been developed and recommended for manufacture. 2. The process of production of continuous fibers from standard glass using 2400 orifice bushing with perforated plates instead of orifice tips without air cooling, has been realized for the first time.
文摘In this paper, a detailed numerical investigation of two-dimensional laminar forced convection in a porous channel with inlet and outlet slot is presented. A uniform heat flux is applied on one wall of channel and another wall is isolated. The flow in the porous medium is modeled using the Brinkman-Forchheimer-extended Darcy model in which the inertia and boundary effects are taken into consideration and thermal dispersion effects are not included in the energy equation. Parametric studies are conducted to evaluate the effects of particle diameter, Reynolds number on the heat transfer and friction factor. Nusselt number and friction factor are developed for efficient design of a porous heat exchanger based on the present configuration. In order to solve this problem Fluent software was used.
文摘The formula of the vibration response and power flow in beam-stiffened plate with force excitation applied on.the plate, have been obtained by using the Steepest Descent Integral method. The characteristics of the power flow have been studied through computer simulation.It is shown that the stiffener acts as an extra lineal excitation applied on the plate and changes the characteristics of the power flow of the infinite plate greatly The greater the stiffness and the smaller the distance between the exciting point and the stiffener is, the greater the induence is. Lastly, experiments have been carried out by using the dualaccelerometer measurement technique that based on cross spectrum, and the test data agree well with the theoretical results
文摘An analysis of the flow in the gap between a rotating cone and a stationary plate at low Reynolds numbers is presented. Using series expansions for the components of the mean velocity profile and the pressure gradient the Navier-Stokes equations and the continuity equation for a Newtonian fluid written in cylindrical coordinates are solved. It is found that the solution is stable and convergent for the local Reynolds numbers Re smaller than 1.2928. The computed angle of the wall streamlines is found to be in good agreement with experimental data.
