Although the analytical solution of the starting flow of Maxwell fluid in a pipe has been derived for a long time, the effect of relaxation time λ on start-up time ts of this flow is still not well understood. Especi...Although the analytical solution of the starting flow of Maxwell fluid in a pipe has been derived for a long time, the effect of relaxation time λ on start-up time ts of this flow is still not well understood. Especially, there exist a series of jumps on the ts-λ. curve. In this paper we introduce a normalized mechanical energy by mode decomposition and mathematical analogy to describe the start-up process. An improved definition of start-up time is presented based on the normalized mechanical energy. It is proved that the ts-λ. curve contains a series of jumps if λ is larger than a critical value. The exact positions of the jumps are determined and the physical reason of the jumps is discussed.展开更多
Gas bearings,which have the advantages of low frictional resistance and power loss,high rotational speed and high temperature operation,and long life,are more suitable than are traditional liquid lubricated bearings b...Gas bearings,which have the advantages of low frictional resistance and power loss,high rotational speed and high temperature operation,and long life,are more suitable than are traditional liquid lubricated bearings because of their high precision,high rotational speed,and special condition support.However,the problem of starting a closed-cycle compression system with gas bearings still needs to be solved for practical application.Thus,a new start-up method for a closed-cycle compression system with aerostatic gas bearings is proposed in this paper.Further,this paper presents a numerical simulation and experimental investigation of the method’s feasibility and characteristics during the start-up process when the gas tank’s initial pressure is fixed.The results show that the gas tank volume is approximately directly proportional to the start-up time allowable,and a gas tank volume sufficiently small,which not only ensures the feasibility of start-up,but also affects other components only slightly,can be obtained.A perfect combination of radial and axial loads also can be achieved to make the start-up time allowable as long as possible.R134a is a better choice for the working medium than is air,as the start-up time allowable is longer,which leads to a smaller gas tank.This research proposes a new start-up method for a closed-cycle compression system with aerostatic gas bearings which has sufficient load capacity to support system during the start-up method.展开更多
文摘Although the analytical solution of the starting flow of Maxwell fluid in a pipe has been derived for a long time, the effect of relaxation time λ on start-up time ts of this flow is still not well understood. Especially, there exist a series of jumps on the ts-λ. curve. In this paper we introduce a normalized mechanical energy by mode decomposition and mathematical analogy to describe the start-up process. An improved definition of start-up time is presented based on the normalized mechanical energy. It is proved that the ts-λ. curve contains a series of jumps if λ is larger than a critical value. The exact positions of the jumps are determined and the physical reason of the jumps is discussed.
基金Supported by National Natural Science Foundation of China(Grant No.51706009).
文摘Gas bearings,which have the advantages of low frictional resistance and power loss,high rotational speed and high temperature operation,and long life,are more suitable than are traditional liquid lubricated bearings because of their high precision,high rotational speed,and special condition support.However,the problem of starting a closed-cycle compression system with gas bearings still needs to be solved for practical application.Thus,a new start-up method for a closed-cycle compression system with aerostatic gas bearings is proposed in this paper.Further,this paper presents a numerical simulation and experimental investigation of the method’s feasibility and characteristics during the start-up process when the gas tank’s initial pressure is fixed.The results show that the gas tank volume is approximately directly proportional to the start-up time allowable,and a gas tank volume sufficiently small,which not only ensures the feasibility of start-up,but also affects other components only slightly,can be obtained.A perfect combination of radial and axial loads also can be achieved to make the start-up time allowable as long as possible.R134a is a better choice for the working medium than is air,as the start-up time allowable is longer,which leads to a smaller gas tank.This research proposes a new start-up method for a closed-cycle compression system with aerostatic gas bearings which has sufficient load capacity to support system during the start-up method.
