The stretching tests of the commercial AZ31 Mg alloy were conducted at 130 ℃, 170 ℃, 210 ℃, at the forming speeds of 10 mm/min and 50 mm/min, respectively. The formability of AZ31 sheets at high temperature was eva...The stretching tests of the commercial AZ31 Mg alloy were conducted at 130 ℃, 170 ℃, 210 ℃, at the forming speeds of 10 mm/min and 50 mm/min, respectively. The formability of AZ31 sheets at high temperature was evaluated by forming limit diagrams (FLD). The fracture morphologies were analyzed using a scanning electron microscope. The results show that the FLD of AZ31 Mg alloy is affected by the forming temperature, in another word, the formability increases with the increasing of the forming temperature. That may be because the non-basal slip system starts to move by thermal activation at high forming temperature. It is also demonstrated that the formability of the AZ31 Mg alloy is on the decline with the increasing of the forming speed. The slipping performs thoroughly to release the stress during the deformation if the forming speed decreases. In addition, the higher the forming temperature is, the more obvious the effect of the forming speed is. The forming temperature is the main dominating factor on the formability of AZ31 Mg alloy.展开更多
Hot deformation behavior of a new type of M3∶ 2 high speed steel with niobium addition made by spray forming was investigated based on compression tests in the temperature range of 950-1 150 ℃ and strain rate of 0. ...Hot deformation behavior of a new type of M3∶ 2 high speed steel with niobium addition made by spray forming was investigated based on compression tests in the temperature range of 950-1 150 ℃ and strain rate of 0. 001-10 s^（-1）. A comprehensive constitutive equation was obtained,which could be used to predict the flow stress at different strains. Processing map was developed on the basis of the flow stress data using the principles of dynamic material model. The results showed that the flow curves were in fair agreement with the dynamic recrystallization model. The flow stresses,which were calculated by the comprehensive constitutive equation,agreed well with the test data at low strain rates（ ≤1 s^（-1））. The material constant（ α）,stress exponent（ n） and the hot deformation activation energy（ Q_（HW）） of the new steel were 0. 006 15 MPa^（-1）,4. 81 and 546 kJ·mol^（-1）,respectively. Analysis of the processing map with an observation of microstructures revealed that hot working processes of the steel could be carried out safely in the domain（ T = 1 050-1 150 ℃,ε = 0. 01- 0. 1 s^（-1））with about 33% peak efficiency of power dissipation（ η）. Cracks was expected in two domains at either lower temperatures（ 〈 1 000 ℃） or low strain rates（ 0. 001 s^（-1）） with different cracking mechanisms. Flow localization occurred when the strain rates exceeded 1 s^（-1） at all testing temperatures.展开更多
文摘The stretching tests of the commercial AZ31 Mg alloy were conducted at 130 ℃, 170 ℃, 210 ℃, at the forming speeds of 10 mm/min and 50 mm/min, respectively. The formability of AZ31 sheets at high temperature was evaluated by forming limit diagrams (FLD). The fracture morphologies were analyzed using a scanning electron microscope. The results show that the FLD of AZ31 Mg alloy is affected by the forming temperature, in another word, the formability increases with the increasing of the forming temperature. That may be because the non-basal slip system starts to move by thermal activation at high forming temperature. It is also demonstrated that the formability of the AZ31 Mg alloy is on the decline with the increasing of the forming speed. The slipping performs thoroughly to release the stress during the deformation if the forming speed decreases. In addition, the higher the forming temperature is, the more obvious the effect of the forming speed is. The forming temperature is the main dominating factor on the formability of AZ31 Mg alloy.
基金Item Sponsored by National Basic Research Program of China(2011CB606303)Constructed Project for Key Laboratory of Beijing of China
文摘Hot deformation behavior of a new type of M3∶ 2 high speed steel with niobium addition made by spray forming was investigated based on compression tests in the temperature range of 950-1 150 ℃ and strain rate of 0. 001-10 s^（-1）. A comprehensive constitutive equation was obtained,which could be used to predict the flow stress at different strains. Processing map was developed on the basis of the flow stress data using the principles of dynamic material model. The results showed that the flow curves were in fair agreement with the dynamic recrystallization model. The flow stresses,which were calculated by the comprehensive constitutive equation,agreed well with the test data at low strain rates（ ≤1 s^（-1））. The material constant（ α）,stress exponent（ n） and the hot deformation activation energy（ Q_（HW）） of the new steel were 0. 006 15 MPa^（-1）,4. 81 and 546 kJ·mol^（-1）,respectively. Analysis of the processing map with an observation of microstructures revealed that hot working processes of the steel could be carried out safely in the domain（ T = 1 050-1 150 ℃,ε = 0. 01- 0. 1 s^（-1））with about 33% peak efficiency of power dissipation（ η）. Cracks was expected in two domains at either lower temperatures（ 〈 1 000 ℃） or low strain rates（ 0. 001 s^（-1）） with different cracking mechanisms. Flow localization occurred when the strain rates exceeded 1 s^（-1） at all testing temperatures.
