Development of a hybrid particle-mesh method for simulating free-surface flows

In this work the feasibility of a numerical wave tank using a hybrid particle-mesh method is investigated.Based on the fluid implicit particle method（FLIP）a formulation for the hybrid method is presented for incompressible multiphase flows involving large density jumps and wave generating boundaries.The performance of the method is assessed for a standing wave and for the generation and propagation of a solitary wave over a flat and a sloping bed.A comparison is made with results obtained with a well-established SPH package.The tests demonstrate that the method is a promising and attractive tool for simulating the nearshore propagation of waves.

4D-Flow MRI在肥厚型心肌病左室流出道血流评估中的价值探索

目的 探索四维血流(four-dimensional flow,4D-Flow)磁共振成像(magnetic resonance imaging,MRI)技术在左心室腔内应用的可行性。材料与方法 本研究为前瞻性、横断面研究,纳入2022年8月至2023年1月于我院接受心脏MRI检查的21例肥厚型心肌病患者,采用3.0 T MRI扫描仪进行二维血流(tow-dimensional flow,2D-Flow)及4D-Flow成像,收集患者一周内进行的超声心动图检查结果。采用组内相关系数(inter-class correlation coefficient,ICC)、变异系数(coefficients of variation,COV)及Bland-Altman分析比较2D-Flow、4D-Flow评估左室流出道峰值流速的可重复性及一致性,并通过Pearson相关性分析探究二者与超声心动图测量结果的关系。结果 2D-Flow和4D-Flow观察者内/观察者间的ICC分别为0.999/0.999和0.995/0.992,COV分别为0.5%/0.5%和2.4%/2.6%。4D-Flow与超声心动图的测量结果呈中度相关,相关系数r值为0.574(P=0.006),但一致性较差,ICC为0.375(P=0.013)。2D-Flow与4D-Flow和超声心动图间无显著的一致性及相关性。结论 4D-Flow技术能够可视化心腔内血流模式,对左室流出道峰值流速的测量具有高度可重复性,且与超声心动图的测量结果具有显著的一致性。

Effect of Viscosity on Free-Surface Waves in Oseen Flows

Based on the complex dispersion relation for the two-dimensional free-surface waves generated by a moving body in the steady Oseen flows, the effect of viscosity on wavelength and wave amplitude was investigated by means of an asymptotic method and a numerical analysis. A comparison between the asymptotic and numerical analysis for the viscous decay factor demonstrates the validity of the perturbation expansions for the wave profile. The numerical result shows that the wavelength of viscous wave is slightly elongated in comparison with that of inviscid wave.

THREE-DIMENSIONAL NON-HYDROSTATIC MODEL FOR FREE-SURFACE FLOWS WITH UNSTRUCTURED GRID

The three-dimensional Navier-Stokes equations were solved with the fractional step method where the hydrostatic pressure component was determined first, while the non-hydrostatic component of the pressure was computed from the pressure Poisson equation in which the coefficient matrix is positive definite and symmetric. The eddy viscosity was calculated from the efficient k-ε turbulence model. The resulting model is computationally efficient and unrestricted to the CFL condition. Computations with and without hydrostatic approximation were compared for the same cases to test the validity of the conventional hydrostatic pressure assumption. The model was verified against analytical solutions and experimental data, with excellent agreement.

肝硬化患者4D flow MRI血流动力学参数与中医证型的相关性研究

目的探讨肝硬化患者4D flow MRI血流动力学参数与中医证型的相关性。方法将118例肝硬化患者依据中医辨证分为肝气郁结证、湿热蕴结证、肝肾阴虚证、脾肾阳虚证、瘀血阻络证5个证型,所有患者均行门静脉4D flow MRI检查,统计不同证型肝硬化患者分布情况,观察门静脉系统(门静脉主干、脾静脉、肠系膜上静脉)的血流动力学参数,包括血流量、流速、壁剪切力等,比较不同证型患者门静脉血流动力学参数差异。结果肝硬化代偿期以肝气郁结证、湿热蕴结证为主,肝硬化失代偿期以脾肾阳虚、瘀血络阻证为主;A级以肝气郁结证、湿热蕴结证为主,B、C级以瘀血络阻证为主。瘀血络阻证肝硬化患者门静脉主干及脾静脉血流量明显高于肝气郁结证、湿热蕴结证患者(P<0.05);脾肾阳虚证门静脉主干血流量明显高于肝气郁结证肝硬化患者(P<0.05);瘀血络阻证肝硬化患者门静脉主干流速及剪切力较肝气郁结证和湿热蕴结证低。结论肝硬化患者中医辨证分型与门静脉血流动力学参数具有一定相关性,4D flow MRI可为肝硬化的中医辨证提供血流动力学参考。

Large eddy simulation of free-surface flows

This paper introduces and discusses numerical methods for flee-surface flow simulations and applies a large eddy simula- tion （LES） based flee-surface-resolved CFD method to a couple of flows of hydraulic engineering interest. The advantages, dis- advantages and limitations of the various methods are discussed. The review prioritises interface capturing methods over interface tracking methods, as these have shown themselves to be more generally applicable to viscous flows of practical engineering interest, particularly when complex and rapidly changing surface topologies are encountered. Then, a LES solver that employs the level set method to capture flee-surface deformation in 3-D flows is presented, as are results from two example calculations that concern com- plex low submergence turbulent flows over idealised roughness elements and bluff bodies. The results show that the method is capable of predicting very complex flows that are characterised by strong interactions between the bulk flow and the free-surface, and permits the identification of turbulent events and structures that would be very difficult to measure experimentally.

基于 Moldflow 的汽车中控台框架翘曲变形分析及优化

以某汽车中控台框架为研究对象,测量试模样品发现其翘曲变形量超过了装配要求。通过Moldflow软件模拟了该塑件实际的注塑过程,翘曲变形量的模拟值与实测平均值的最大误差为5.98%,发现该塑件翘曲变形的主要因素为冷却不均和收缩不均。本文在原物料中添加质量分数为25%的玻璃纤维以及优化工艺参数后,翘曲变形量的模拟值与初始方案相比降低了86.22%。试模验证表明,优化后的翘曲变形量模拟值与实测平均值的最大误差为4.35%,证明了Moldflow软件模拟分析的准确性。试模后各检测点的最大翘曲变形量降到了1.6 mm以下,较优化之前降低了80%以上,为类似大型复杂注塑件的翘曲变形分析及优化提供了思路。

V Flow技术测量颈动脉壁面剪应力的一致性研究

目的评价血流向量成像(V Flow)技术在测量健康成年人颈动脉壁面剪应力(WSS)中的一致性。方法于2021年2月至2021年3月招募健康成年志愿者20人,由2名不同年资的超声医师使用配备V Flow功能的Mindray Resona 7超声仪和3~9 MHz线阵探头进行双侧颈动脉扫查,分别采集双侧颈总动脉远段、颈总动脉分叉至颈内动脉起始部两段动脉的动态V Flow图像,测量两侧颈总动脉远段的近心端、远心端、分叉处及颈内动脉起始部的前、后壁的WSS,使用组内相关系数(ICC)和Bland-Altman图评估组内一致性及组间一致性。结果双侧颈动脉前、后壁的4个不同节段之间WSS值差异均有统计学意义(P<0.05)。高年资超声医师2次测量结果的一致性结果显示,左侧颈总动脉远段的远心端一致性极好(ICC 0.779),右侧颈总动脉远段的近心端(ICC 0.605)、远心端(ICC 0.585)、颈内动脉起始部(ICC 0.457)、左侧颈总动脉分叉处(ICC 0.606)及颈内动脉起始部(ICC 0.702)一致性均较好;不同年资超声医师的测量结果显示,仅右侧颈总动脉分叉处(ICC 0.486)及左侧颈总动脉远段的远心端(ICC 0.576)一致性较好。结论V Flow技术可显示不同位点间颈动脉WSS之间的差异,其组内一致性较好,但在不同年资超声医师间存在一定的差异。

基于Moldflow软件对薄壁件某塑料喷嘴的注塑方案优化研究

喷嘴注塑产品的质量和性能很大程度上由注塑方案和工艺参数所决定,不当的注塑方案和工艺参数会导致充填不足、熔接线过多、翘曲变形量大等问题。为了可以减少生产周期,节约生产成本,利用三维软件UG对喷嘴进行建模,基于模流分析软件Moldflow软件对喷嘴注塑产品进行分析和优化,通过比较点浇口和侧浇口两种方案的分析结果,最终确定该产品点浇口的方案更好。并通过设计正交实验,得到优化后的工艺参数。

基于MoldFlow太阳能储能系统下盖成型模拟及应用

以太阳能储能系统下盖模流分析为例,反复修改流道和浇口截面尺寸与长度以及主流道位置,确定流道尺寸。运用MoldFlow对设计好的流道进行充填分析,以使成型达到流动平衡,并进行冷却、翘曲分析,预测成型缺陷,提出解决措施,为模具设计提供浇注系统和冷却系统方案和注射成型工艺参数,并应用于模具设计和实际生产。

Dissipative free-surface solver for potential flow around hydrofoil distributed with doublets

A doublet integral equation is formulated for the two-dimensional dissipative potential flow around a hydrofoil submerged below a free-water surface. The free-water surface is assumed to involve energy dissipation, and thus it is the source of damping. A doublet panel method is developed from incorporation of the dissipative Green function approach and the doublet distributions on the hydrofoil surface. Numerical computations are implemented, and the derived numerical results are in good agreement with analytic solutions and experimental measurements.

A transient production prediction method for tight condensate gas wells with multiphase flow

Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir,a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed,and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established.The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure.In the early stage of production or in areas far from the wellbore with high reservoir pressure,the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models.In the late stage of production or in areas close to the wellbore with low reservoir pressure,the condensate oil saturation can be calculated using the data of constant composition expansion test.In the middle stages of production or when reservoir pressure is at an intermediate level,the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure.Through simulation and field application,the new method is verified to be reliable and practical.It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.

Debris Fan Produced by Failure of Canyon-Blocking Pyroclastic Flows

Ash-rich pyroclastic flows from the cataclysmic eruption of Mount Mazama (~7700 yr. B. P.), Cascade volcanic arc, Oregon, entered and blocked the narrow, bedrock-lined canyon of the Williamson River approximately 35 to 44 km from the source volcano. The blockage impounded a body of water which then released producing four stratigraphic units in the downstream debris fan. The four stratigraphic units are a boulder core comprised of locally sourced bedrock boulders and three sand-rich units including a fine-grained sand unit, a sandy pumice gravel (±basalt/hydrovolcanic tuff) unit, and a pumice pebble-bearing, crystal-rich sand unit. Hand-drilled auger holes up to ~1.6 m deep were used to obtain samples of the sand-rich units. Units were delimited using surface and down-hole observations, composition and texture, estimated density, statistical parameters of grain size, and vertical and lateral distribution of properties. Overtopping followed by rapid incision into the ash-rich pyroclastic flows progressively cleared the canyon, but a bedrock knickpoint near the head of the canyon limited the volume of debris available for transport to about 0.04 km3 to 0.08 km3. Co-deposition of bedrock boulders and lithic-rich sand was followed by rapid deposition with minimal reworking of remobilized pyroclastics. Continued draining of the impounded lake sent hyperconcentrated flows onto the debris fan depositing pumice-rich gravels that graded upward to crystal-rich sands.

Diagnostic performance of intravascular ultrasound-based fractional flow reserve in evaluating of intermediate left main stenosis

BACKGROUND The recently introduced ultrasonic flow ratio(UFR),is a novel fast computational method to derive fractional flow reserve(FFR)from intravascular ultrasound(IVUS)images.In the present study,we evaluate the diagnostic performance of UFR in patients with intermediate left main(LM)stenosis.METHODS This is a prospective,single center study enrolling consecutive patients with presence of intermediated LM lesions(diameter stenosis of 30%-80%by visual estimation)underwent IVUS and FFR measurement.An independent core laboratory assessed offline UFR and IVUS-derived minimal lumen area(MLA)in a blinded fashion.RESULTS Both UFR and FFR were successfully achieved in 41 LM patients(mean age,62.0±9.9 years,46.3%diabetes).An acceptable correlation between UFR and FFR was identified(r=0.688,P<0.0001),with an absolute numerical difference of 0.03(standard difference:0.01).The area under the curve(AUC)in diagnosis of physiologically significant coronary stenosis for UFR was 0.94(95%CI:0.87-1.01),which was significantly higher than angiographic identified stenosis>50%(AUC=0.66,P<0.001)and numerically higher than IVUS-derived MLA(AUC=0.82;P=0.09).Patient level diagnostic accuracy,sensitivity and specificity for UFR to identify FFR≤0.80 was 82.9%(95%CI:70.2-95.7),93.1%(95%CI:82.2-100.0),58.3%(95%CI:26.3-90.4),respectively.CONCLUSION In patients with intermediate LM diseases,UFR was proved to be associated with acceptable correlation and high accuracy with pressure wire-based FFR as standard reference.The present study supports the use of UFR for functional evaluation of intermediate LM stenosis.

A multichannel thermal bubble-actuated impedance flow cytometer with on-chip TIA based on CMOS-MEMS

Electrochemical impedance spectroscopy(EIS)flow cytometry offers the advantages of speed,affordability,and portability in cell analysis and cytometry applications.However,the integration challenges of microfluidic and EIS read-out circuits hinder the downsizing of cytometry devices.To address this,we developed a thermal-bubble-driven impedance flow cytometric application-specific integrated circuit(ASIC).The thermal-bubble micropump avoids external piping and equipment,enabling high-throughput designs.With a total of 36 cell counting channels,each measuring 884×220μm^(2),the chip significantly enhances the throughput of flow cytometers.Each cell counting channel incorporates a differential trans-impedance amplifier(TIA)to amplify weak biosensing signals.By eliminating the parasitic parameters created at the complementary metal-oxidesemiconductor transistor(CMOS)-micro-electromechanical systems(MEMS)interface,the counting accuracy can be increased.The on-chip TIA can adjust feedback resistance from 5 to 60 kΩto accommodate solutions with different impedances.The chip effectively classifies particles of varying sizes,demonstrated by the average peak voltages of 0.0529 and 0.4510 mV for 7 and 14μm polystyrene beads,respectively.Moreover,the counting accuracies of the chip for polystyrene beads and MSTO-211H cells are both greater than 97.6%.The chip exhibits potential for impedance flow cytometer at low cost,high-throughput,and miniaturization for the application of point-of-care diagnostics.

Numerical simulation on the multiphase flow and reoxidation of the molten steel in a two-strand tundish during ladle change

A 3D mathematical model was proposed to investigate the molten steel–slag–air multiphase flow in a two-strand slab continuous casting(CC)tundish during ladle change.The study focused on the exposure of the molten steel and the subsequent reoxidation occurrence.The exposure of the molten steel was calculated using the coupled realizable k–εmodel and volume of fluid(VOF)model.The diffusion of dissolved oxygen was determined by solving the user-defined scalar(UDS)equation.Moreover,the user-defined function(UDF)was used to describe the source term in the UDS equation and determine the oxidation rate and oxidation position.The effect of the refilling speed on the molten steel exposure and dissolved oxygen content was also discussed.Increasing the refilling speed during ladle change reduced the refilling time and the exposure duration of the molten steel.However,the elevated refilling speed enlarged the slag eyes and increased the average dissolved oxygen content within the tundish,thereby exacerbating the reoxidation phenomenon.In addition,the time required for the molten steel with a high dissolved oxygen content to exit the tundish varied with the refilling speed.When the inlet speed was 3.0 m·s^(-1)during ladle change,the molten steel with a high dissolved oxygen content exited the outlet in a short period,reaching a maximum dissolved oxygen content of 0.000525wt%.Conversely,when the inlet speed was 1.8 m·s^(-1),the maximum dissolved oxygen content was 0.000382wt%.The refilling speed during the ladle change process must be appropriately decreased to minimize reoxidation effects and enhance the steel product quality.

Verification and Validation of High-Resolution Inviscid and Viscous Conical Nozzle Flows

Capturing elaborated flow structures and phenomena is required for well-solved numerical flows.The finite difference methods allow simple discretization of mesh and model equations.However,they need simpler meshes,e.g.,rectangular.The inverse Lax-Wendroff(ILW)procedure can handle complex geometries for rectangular meshes.High-resolution and high-order methods can capture elaborated flow structures and phenomena.They also have strong mathematical and physical backgrounds,such as positivity-preserving,jump conditions,and wave propagation concepts.We perceive an effort toward direct numerical simulation,for instance,regarding weighted essentially non-oscillatory(WENO)schemes.Thus,we propose to solve a challenging engineering application without turbulence models.We aim to verify and validate recent high-resolution and high-order methods.To check the solver accuracy,we solved vortex and Couette flows.Then,we solved inviscid and viscous nozzle flows for a conical profile.We employed the finite difference method,positivity-preserving Lax-Friedrichs splitting,high-resolution viscous terms discretization,fifth-order multi-resolution WENO,ILW,and third-order strong stability preserving Runge-Kutta.We showed the solver is high-order and captured elaborated flow structures and phenomena.One can see oblique shocks in both nozzle flows.In the viscous flow,we also captured a free-shock separation,recirculation,entrainment region,Mach disk,and the diamond-shaped pattern of nozzle flows.

Extending homogeneous fluidization flow regime of Geldart-A particles by exerting axial uniform and steady magnetic field

The homogeneous/particulate fluidization flow regime is particularly suitable for handling the various gas–solid contact processes encountered in the chemical and energy industry.This work aimed to extend such a regime of Geldart-A particles by exerting the axial uniform and steady magnetic field.Under the action of the magnetic field,the overall homogeneous fluidization regime of Geldart-A magnetizable particles became composed of two parts:inherent homogeneous fluidization and newly-created magnetic stabilization.Since the former remained almost unchanged whereas the latter became broader as the magnetic field intensity increased,the overall homogeneous fluidization regime could be extended remarkably.As for Geldart-A nonmagnetizable particles,certain amount of magnetizable particles had to be premixed to transmit the magnetic stabilization.Among others,the mere addition of magnetizable particles could broaden the homogeneous fluidization regime.The added content of magnetizable particles had an optimal value with smaller/lighter ones working better.The added magnetizable particles might raise the ratio between the interparticle force and the particle gravity.After the magnetic field was exerted,the homogeneous fluidization regime was further expanded due to the formation of magnetic stabilization flow regime.The more the added magnetizable particles,the better the magnetic performance and the broader the overall homogeneous fluidization regime.Smaller/lighter magnetizable particles were preferred to maximize the magnetic performance and extend the overall homogeneous fluidization regime.This phenomenon could be ascribed to that the added magnetizable particles themselves became more Geldart-A than-B type as their density or size decreased.

Effect of aspect ratio of elliptical stirred vessel on mixing time and flow field characteristics in the absence of baffles

Elliptical tanks were used as an alternative to circular tanks in order to improve mixing efficiency and reduce mixing time in unbaffled stirred tanks(USTs). Five different aspect ratios of elliptical vessels were designed to compare their mixing time and flow field. Computational fluid dynamics(CFD) simulations were performed using the k–ε model to calculate the mixing time and simulate turbulent flow field features, such as streamline shape, velocity distribution, vortex core region distribution, and turbulent kinetic energy(TKE) transfer. Visualization was also carried out to track the tinctorial evolution of the liquid phase. Results reveal that elliptical stirred tanks can significantly improve mixing performance in USTs. Specifically, the mixing time at an aspect ratio of 2.00 is only 45.3% of the one of a circular stirred tank. Furthermore, the secondary flow is strengthened and the vortex core region increases with the increase of aspect ratio. The axial velocity is more sensitive to the aspect ratio than the circumferential and radial velocity. Additionally, the TKE transfer in elliptical vessels is altered. These findings suggest that elliptical vessels offer a promising alternative to circular vessels for enhancing mixing performance in USTs.

Enhancing wood efficiency through comprehensive wood flow analysis:Methodology and strategic insights

Wood,an essential natural resource in human civilization,remains widely used despite advances in technology and material substitution.The surge in greenhouse gas emissions and environmental concerns accentuates the need for optimizing wood utilization.Material flow analysis is a powerful tool for tracking material flows and stocks,aiding resource management and environmental decision-making.However,the full extent of its methodological dimensions,particularly within the context of the wood supply chain,remains relatively unexplored.In this study,we delve into the existing literature on wood flow analysis,discussing its primary objectives,materials involved,temporal and spatial scales,data sources,units,and conversion factors.Additionally,data uncertainty,data reconciliation and crucial assumptions in material flow analysis are highlighted in this paper.Key findings reveal the significance of wood cascading and substitution effects by replacing non-wood materials,where they can reduce greenhouse gas emissions more than the natural carbon sink of forests and wood products.The immediate impact of short-term wood cascading might not be as robust as the substitution effect,with energy substitution showcasing better results than material substitution.However,it's crucial to note that these conclusions could experience significant reversal from a long-term and global perspective.Strategies for improving wood efficiency involve maximizing material use,advancing construction technologies,extending product lifespans,promoting cascade use,and optimizing energy recovery processes.The study underscores the need for standardized approaches in wood flow analysis and emphasizes the potential of wood efficiency strategies in addressing environmental challenges.