A Novel High Spectral Efficiency Waveform Coding-OVFDM

Based on the Overlapped Multiplexing Principle[12],a frequency domain OVFDM(Overlapped Frequency Domain Multiplexing) Coding is proposed.By the data weighted shift overlapped version of any band-limited Multiplexing Transfer Function H(f) the coding gain and spectral efficiency are both achieved.The heavier the overlap of the data weighted Multiplexing Transfer Function H(f),the higher the coding gain and spectral efficiency as well as the closer the output to the optimum complex Gaussian distribution.The bit error probability performance is estimated.The time domain OVTDM(Overlapped Time Domain Multiplexing) Coding,the dual of OVFDM in time domain is incidentally proposed as well.Both theoretical analysis and testified simulations show that OVFDM(OVTDM) is suitable for high spectral efficiency application and its spectral efficiency is only roughly linear to SNR rather than the well-known logarithm to SNR.

LD Pumped High Efficient Intracavity Frequency-Doubled Green Laser

A laser diode (LD) pumped Q switched high efficient intracavity frequency doubled Nd ∶YAG laser is reported here. The authors have designed an optical coupler and pointed out that the key to increasing harmonic conversion efficiency is to decrease the loss of fundamental wave. In the experiments, a fundamental mode output laser was acquired. When the pumping power was 12 W, 2.6 W average output power at 1 064 nm with AO Q switch was obtained. 2.1 W average output power at 532 nm was obtained with intracavity frequency doubling, and the highest second harmonic conversion efficiency was 82 0 0.

Several Modulation in Direct-Sequence Spectrum-Spread Systems

Performances of BPSK, balanced quaternary modulation, dual quaternary modulation and complex quaternary modulation in direct sequence spectrum spread (DS SS) system are discussed in this paper. Based on the criterion the power of original signal is the same, it is shown that complex quaternary modulation has the best performance, and dual quaternary modulation degrades 2dB. Moreover, the frequency efficient of the two modulations is 2bit/Hz. Balanced quaternary has the same performance as BPSK with frequency efficient 1bit/Hz.

Fourier time spectral method for subsonic and transonic flows

The time accuracy of the exponentially accurate Fourier time spectral method（TSM） is examined and compared with a conventional 2nd-order backward difference formula（BDF） method for periodic unsteady flows. In particular, detailed error analysis based on numerical computations is performed on the accuracy of resolving the local pressure coefficient and global integrated force coefficients for smooth subsonic and non-smooth transonic flows with moving shock waves on a pitching airfoil. For smooth subsonic flows, the Fourier TSM method offers a significant accuracy advantage over the BDF method for the prediction of both the local pressure coefficient and integrated force coefficients. For transonic flows where the motion of the discontinuous shock wave contributes significant higherorder harmonic contents to the local pressure fluctuations,a sufficient number of modes must be included before the Fourier TSM provides an advantage over the BDF method.The Fourier TSM, however, still offers better accuracy than the BDF method for integrated force coefficients even for transonic flows. A problem of non-symmetric solutions for symmetric periodic flows due to the use of odd numbers of intervals is uncovered and analyzed. A frequency-searching method is proposed for problems where the frequency is not known a priori. The method is tested on the vortex shedding problem of the flow over a circular cylinder.

Ion beam figuring of continuous phase plates based on the frequency filtering process

Ion beam figuring （IBF） technology is an effective technique for fabricating continuous phase plates （CPPs） with small feature structures. This study proposes a multi-pass IBF approach with different beam diameters based on the frequency filtering method to improve the machining accuracy and efficiency of CPPs during IBF. We present the selection principle of the frequency filtering method, which incorporates different removal functions that maximize material removal over the topographical frequencies being imprinted. Large removal functions are used early in the fabrication to figure the surface profile with low frequency. Small removal functions are used to perform final topographical correction with higher fre- quency and larger surface gradient. A high-precision surface can be obtained as long as the filtering frequency is suitably selected. This method maximizes the high removal efficiency of the large removal function and the high corrective capability of the small removal function. Consequently, the fast convergence of the machining accuracy and efficiency can be achieved.

Amplification assisted difference frequency generation for efficient mid-infrared conversion based on monolithic tandem lithium niobate superlattice

We report the investigation on the performance of an amplification assisted difference frequency generation(AA-DFG) system driven by pulsed pump and continuous-wave primary signal lasers. A monolithic tandem lithium niobate superlattice was employed as the nonlinear crystal with a uniform grating section for the DFG process, followed by a chirp section for the optical parametric amplification process. The impacts of pump pulse shape, primary signal power, input beam diameter, and crystal structure on the pump-to-idler conversion efficiency of the AA-DFG system were comprehensively studied by numerically solving the coupled wave equations. It is concluded that square pump pulse and high primary signal power are beneficial to high pump-to-idler conversion efficiency. In addition, tighter input beam focus and smaller DFG length proportion could redeem the reduction in conversion efficiency resulting from wider acceptance bandwidths for the input lasers. We believe that such systems combining the merits of high stability inherited from cavity-free configuration and high efficiency attributed from the cascaded nonlinear conversion should be of great interest to a wide community,especially when the pulse shaping technique is incorporated.

Two-dimensional CoNi@mesoporous carbon composite with heterogeneous structure toward broadband microwave absorber

Constructing composites with heterogeneous structure and dual loss mechanism shows great potential in designing microwave absorbers.In this work,two-dimensional cobalt and nickel alloys@mesoporous carbon(CoNi@MC)composites were constructed via using CoNi layered double hydroxide@mesoporous polydopamine(CoNi LDH@MPDA)as sacrifice template.During the pyrolysis process,the MPDA is transformed into mesoporous carbon coated the surface of CoNi LDH that is further reduced to CoNi alloys.The mesoporous structure is conducive to the multi-reflection of electromagnetic waves and facilitates optimizing impedance matching.Heterogeneous interfaces between CoNi alloys and mesoporous carbon induce interface polarization.Multiple attenuation mechanism promotes the electromagnetic waves conversion.The maximum reflection loss of CoNi@MC composite is−70.86 dB and the widest effective absorption bandwidth is 7.74 GHz covering almost the entire Ku band.This strategy will be a guidance for designing electromagnetic absorbers.

Modeling of aggregation kernels for fluidized beds using discrete particle model simulations

Aggregation is one of the many important processes in chemical and process engineering. Several researchers have attempted to understand this complex process in fluidized beds using the macro-model of population balance equations （PBEs）. The aggregation kernel is an effective parameter in PBEs, and is defined as the product of the aggregation efficiency and collision frequency functions. Attempts to derive this kernel have taken different approaches, including theoretical, experimental, and empirical techniques. The present paper calculates the aggregation kernel using micro-model computer simulations, i.e., a discrete particle model. We simulate the micro-model without aggregation for various initial conditions, and observe that the collision frequency function is in good agreement with the shear kernel. We then simulate the micro-model with aggregation and calculate the aggregation efficiency rate.