An mmWave Dual-Band Integrated Substrate Gap Waveguide Single Cavity Filter with Frequency Selectivity

A novel dual-band ISGW cavity filter with enhanced frequency selectivity is proposed in this paper by utilizing a multi-mode coupling topology.Its cavity is designed to control the number of modes,and then the ports are determined by analyzing the coupling relationship between these selected modes.By synthesizing the coupling matrix of the filter,a nonresonating node(NRN)structure is introduced to flexibly tune the frequency of modes,which gets a dualband and quad-band filtering response from a tri-band filter no the NRN.Furthermore,a frequency selective surface(FSS)has been newly designed as the upper surface of the cavity,which significantly improves the bad out-of-band suppression and frequency selectivity that often exists in most traditional cavity filter designs and measurements.The results show that its two center frequencies are f01=27.50 GHz and f02=32.92GHz,respectively.Compared with the dual-band filter that there is no the FSS metasurface,the out-of-band suppression level is improved from measured 5 dB to18 dB,and its finite transmission zero(FTZ)numbers is increased from measured 1 to 4 between the two designed bands.Compared with the tri-band and quadband filter,its passband bandwidth is expanded from measured 1.17%,1.14%,and 1.13% or 1.31%,1.50%,0.56%,and 0.57% to 1.71% and 1.87%.In addition,the filter has compact,small,and lightweight characteristics.

A Dual-polarized Frequency Selective Rasorber with a Tunable Transparent Band

A tunable dual polarization absorption-transmission-absorption(A-T-A)frequency selective absorbers(FSR)to address the issue of high insertion loss in current tunable FSRs is proposed.The lumped resistors are loaded onto the lossy layer to absorb electromagnetic waves within the absorption band.The varactor diodes are loaded onto another lossless layer to control the transmission frequency band of the FSR.Its equivalent circuit model is provided.The proposed tunable FSR can change the passband within the range of 14.5~15.5 GHz by changing the bias voltage applied to the lossless transmission layer,while maintaining insertion loss above-1.67 dB.The series resonant structure of the lossy layer generates bilateral absorption bands between 10.2~13.5 GHz and 17.2~22 GHz,with broadband reflection suppression ranging from 10.3 GHz to 22 GHz(70.7%).The prototype is manufactured,and the measured results have verified the simulation results.

Enhanced microwave absorption property of silver decorated biomass ordered porous carbon composite materials with frequency selective surface incorporation

Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.

A band-pass frequency selective surface with polarization rotation

A band-pass frequency selective surface(FSS) with polarization rotation property is proposed. The proposed polarization rotating FSS(PR-FSS) is a two-dimensional periodic structure, its unit cell is an antenna-filter-antenna(AFA) module,and the polarization directions of the upper and lower antennas in each AFA module are orthogonal to each other, so the PR-FSS can achieve frequency selection and 90 degrees polarization rotation at the same time. The numerical simulation demonstrate that the anticipated frequency selection and polarization rotation are realized by the PR-FSS in the frequency band from 8.84 GHz to 10.30 GHz with a relative bandwidth of 15.26%, and the maximum insertion loss in the pass band is only 0.17 d B. Finally, one effective experiment validation is carried out, a reasonable agreement is observed between the experimental and simulated results except for a slight deviation caused by fabrication error and measurement tolerance.

Modelling of Wideband Concentric Ring Frequency Selective Surface for 5G Devices

Frequency selective surfaces(FSSs)play an important role in wireless systems as these can be used as filters,in isolating the unwanted radiation,in microstrip patch antennas for improving the performance of these antennas and in other 5G applications.The analysis and design of the double concentric ring frequency selective surface(DCRFSS)is presented in this research.In the sub-6 GHz 5G FR1 spectrum,a computational synthesis technique for creating DCRFSS based spatial filters is proposed.The analytical tools presented in this study can be used to gain a better understanding of filtering processes and for constructing the spatial filters.Variation of the loop sizes,angles of incidence,and polarization of the concentric rings are the factors which influence the transmission coefficient as per the thorough investigation performed in this paper.A novel synthesis approach based on mathematical equations that may be used to determine the physical parameters ofDCRFSSbased spatial filters is presented.The proposed synthesis technique is validated by comparing results from high frequency structure simulator(HFSS),Ansys electronic desktop circuit editor,and an experimental setup.Furthermore,the findings acquired from a unit cell are expanded to a 2×2 array,which shows identical performance and therefore proves its stability.

A Heterogeneous Information Fusion Deep Reinforcement Learning for Intelligent Frequency Selection of HF Communication

The high-frequency(HF) communication is one of essential communication methods for military and emergency application. However, the selection of communication frequency channel is always a difficult problem as the crowded spectrum, the time-varying channels, and the malicious intelligent jamming. The existing frequency hopping, automatic link establishment and some new anti-jamming technologies can not completely solve the above problems. In this article, we adopt deep reinforcement learning to solve this intractable challenge. First, the combination of the spectrum state and the channel gain state is defined as the complex environmental state, and the Markov characteristic of defined state is analyzed and proved. Then, considering that the spectrum state and channel gain state are heterogeneous information, a new deep Q network(DQN) framework is designed, which contains multiple sub-networks to process different kinds of information. Finally, aiming to improve the learning speed and efficiency, the optimization targets of corresponding sub-networks are reasonably designed, and a heterogeneous information fusion deep reinforcement learning(HIF-DRL) algorithm is designed for the specific frequency selection. Simulation results show that the proposed algorithm performs well in channel prediction, jamming avoidance and frequency channel selection.

Improvement on the wave absorbing property of a lossy frequency selective surface absorber using a magnetic substrate

An equivalent-circuit model is used to analyse the improvement of the wave absorbing performance of the lossy frequency selective surface（FSS） absorber by using a magnetic substrate,showing that it is possible to widen the wave absorbing bandwidth.Three pieces of magnetic substrates are prepared.According to the complex permittivity and permeability,the reflectivity of the corresponding absorber is calculated by the finite difference time-domain（FDTD） method,and the bandwidth of the reflectivity below 10 dB is optimized by genetic algorithm.The calculated results indicate that the wave absorbing performance is significantly improved by increasing the complex permeability of the substrate;the reflectivity bandwidth below 10 dB of the single layer FSS absorber can reach 3.6-18 GHz with a thickness of 5 mm,which is wider than that with a dielectric substrate.The density of the FSS absorber is only 0.92 g/cm 3.Additionally,the absorption band can be further widened by inserting a second lossy FSS.Finally,a double layer lossy FSS absorber with a magnetic substrate is fabricated based on the design result.The experimental result is consistent with the design one.

An ultrathin wide-band planar metamaterial absorber based on a fractal frequency selective surface and resistive film

We propose an ultrathin wide-band metamaterial absorber （MA） based on a Minkowski （MIK） fractal frequency selective surface and resistive film. This absorber consists of a periodic arrangement of dielectric substrates sandwiched with an MIK fractal loop structure electric resonator and a resistive film. The finite element method is used to simulate and analyze the absorption of the MA. Compared with the MA-backed copper film, the designed MA-backed resistive film exhibits an absorption of 90% at a frequency region of 2 GHz-20 GHz. The power loss density distribution of the MA is further illustrated to explain the mechanism of the proposed MA. Simulated absorptions at different incidence cases indicate that this absorber is polarization-insensitive and wide-angled. Finally, further simulated results indicate that the surface resistance of the resistive film and the dielectric constant of the substrate can affect the absorbing property of the MA. This absorber may be used in many military fields.

Infrared transparent frequency selective surface based on iterative metallic meshes

In this paper, we present an infrared transparent frequency selective surface（ITFSS） based on iterative metallic meshes, which possesses the properties of high transmittance in infrared band and band-pass effect in millimeter wave band. Cross-slot units are designed on the iterative metallic meshes, which is composed of two same square metallic meshes with a misplaced overlap. In the infrared band of 3–5 μm, the ITFSS has an average transmittance of 80% with a Mg F2 substrate. In the millimeter wave band, a transmittance of-0.74 d B at the resonance frequency of 39.4 GHz is obtained. Moreover, theoretical simulations of the ITFSS diffractive characteristics and transmittance response are also investigated in detail. This ITFSS may be an efficient way to achieve the metamaterial millimeter wave/infrared functional film.

Frequency selective surface with better polarization independency for arbitrary incident angle

This paper investigates the frequency-selective property of a planar layer consisting of period arrays both theoretically and experimentally for different polarizations at arbitrary incident angle. The novel element is designed by loading the rectangular microstrip element with L-shaped conducting patch at its two ends. Based on the spectral-domain method, the frequency response including angle effect and polarization effect of the frequency selective surface （FSS） structure are analysed and the plots of the frequency versus transmission coefficient are obtained. As a result of the numerical analysis, it is shown that if the source polarization is changed, polarization-independence of previous FSS design can be achieved only for normal incidence, which limits most FSS applications. But in our proposed structure, the better polarization-independency for arbitrary incident angle can be achieved. It is observed that the simulated result comes very close to the experimental result.

Tunable frequency selective surface with a shorted ring slot

In order to realize the tunable performance of a frequency selective surface （FSS）, a new unit cell is designed in this paper by properly adding two metal shorts to the ring slot. Based on the spectral-domain method, the frequency responses of the FSS structure with two shorts per slot ring are analysed for both the horizontal and the vertical polarizations at the normal incidence. It is demonstrated that the presence of the metal shorts does not affect the resonant frequency of the horizontally polarized wave but doubles the resonant frequency of the vertically polarized wave. Therefore based on the analysis of the novel transmission properties, a new approach to adjusting the resonant frequency by rotating the FSS screen 90° is presented in this paper.

Controlling Ion Conductance and Channels to Achieve Synapticlike Frequency Selectivity

Enhancing ion conductance and controlling transport pathway in organic electrolyte could be used to modulate ionic kinetics to handle signals. In a Pt/Poly(3-hexylthiophene-2,5-diyl)/Polyethylene?Li CF3SO3/Pt hetero-junction, the electrolyte layer handled at high temperature showed nano-fiber microstructures accompanied with greatly improved salt solubility. Ions with high mobility were confined in the nano-fibrous channels leading to the semiconducting polymer layer,which is favorable for modulating dynamic doping at the semiconducting polymer/electrolyte interface by pulse frequency.Such a device realized synaptic-like frequency selectivity, i.e., depression at low frequency stimulation but potentiation at high-frequency stimulation.

Design of multi-band frequency selective surfaces using multi-periodicity combined elements

Traditional multi-band frequency selective surface （FSS） approaches are hard to achieve a perfect resonance response in a wide band due to the limit of the onset grating lobe frequency determined by the array. To solve this problem, an approach of combining elements in different period to build a hybrid array is presented. The results of series of numerical simulation show that multi-periodicity combined element FSS, which are designed using this approach, usually have much weaker grating lobes than the traditional FSS. Furthermore, their frequency response can be well predicted through the properties of their member element FSS. A prediction method for estimating the degree of expected grating lobe energy loss in designing multi-band FSS using this approach is provided.

Design and Measurement of Microwave Absorbers Comprising Resistive Frequency Selective Surfaces

Frequency selective surfaces (FSSs) have been successfully used in constructing microwave absorbers which demonstrate the ability of modifying and improving its absorbing performances. In this paper, microwave absorber based on ferromagnetic nano-films has been proposed and investigated with a structure similar to that of the Salisbury screen except that the resistive sheet is replaced by FSS of square patch array of the nano-film. We have explored the FSS absorber from three aspects: equivalent circuit model, electromagnetic full-wave simulation and the actual sample measurement. By carefully tuning the patch size, the thickness of the dielectric spacer and the specification of the ferromagnetic nano-film, we obtain the optimized performance of broadband microwave absorbing. Due to the light weight of the nano-films, the proposed absorbers can achieve an ultra-low surface density less than 0.25 kg/m2.

Design of a tunable frequency selective surface absorber as a loaded receiving antenna array

An effective approach to designing a tunable electromagnetic absorber is presented and experimentally verified; it is based on an idea that an existing frequency selective surface （FSS） absorber is regarded as a loaded receiving antenna array. The existing absorber is effectively simplified by withdrawing half of the loaded resistors; a more compact one is obtained when lumped capacitors are introduced. Building on this, a varactor-tunable absorber with a proper bias network is proposed. Numerical simulations of one tunable absorber with 1.6 mm in thickness show that a wide tuning range from 3.05 GHz to 1.96 GHz is achieved by changing the capacitance of the loaded varactor from 0.5 pF to 5.0 pF. An experiment is carried out using a rectangular waveguide measurement setup and excellent agreement between the simulated and measured results is demonstrated.

A new layered space-time detection algorithm for frequency selective fading multiple-input multiple-output channels based on particle filter

In this paper, a new observation equation of non-Gaussian frequency selective fading Bell Labs layered space time （BLAST） architecture system is proposed, which is used for frequency selective fading channels and non-Gaussian noise in an application environment of BLAST system. With othogonal matrix triangularization （QR decomposition） of the channel matrix, the static observation equation of frequency selective fading BLAST system is transformed into a dynamic state space model, and then the particle filter is used for space-time layered detection. Making the full use of the finite alphabet of the digital modulation communication signal, the optimal proposal distribution can be chosen to produce particle and update the weight. Incorporated with current method of reducing error propagation, a new space-time layered detection algorithm is proposed. Simulation result shows the validity of the proposed algorithm.

Frequency selective surface structure optimized by genetic algorithm

Frequency selective surface （FSS） is a two-dimensional periodic structure which has promiaent characteristics of bandpass or bandbloek when interacting with electromagnetic waves. In this paper, the thickness, the dielectric constant, the element graph and the arrangement periodicity of an FSS medium are investigated by Genetic Algorithm （GA） when an electromagnetic wave is incident on the FSS at a wide angle, and an optimized FSS structure and transmission characteristics are obtained. The results show that the optimized structure has better stability in relation to incident angle of electromagnetic wave and preserves the stability of centre frequency even at an incident angle as large as 80°, thereby laying the foundation for the application of FSS to curved surfaces at wide angles.

A millimeter and sub-millimeter wave frequency selective surface beamsplitter for geostationary orbit microwave radiometers

We report the design of three frequency selective surface （FSS） filters used on the FengYun-4 （FY-4） microwave satellite, which separate five-frequency bands in the frequency range of 50-429 GHz with the insertion loss less than 0.4 dB, and separation between adjacent channels more than 20 dB for either TE or TM incidence. Firstly, we briefly introduce the disadvantages of two types of FSS filter： waveguide-array FSS and printed FSS, which are commonly employed in the millimeter and sub-millimeter wave band. In order to meet the insertion loss requirement and specified spectral transmission response, we adopt a filter composed of two closely spaced freestanding metal plates, which con- tains an array of resonant ring slot elements. Computer simulation technology （CST） is used to optimize the structural dimensions of the resonant unit and interlayer separation. Numerical results show that these FSS filters exhibit trans- mission loss of less than 0.4 dB and separation between adjacent channels of more than 20 dB. Simulated transmission coefficients are in close agreement with the required specification, and even exceed the performance specifications.

Frequency-selective microwave polarization rotator using substrate-integrated waveguide cavities

A frequency selective polarization rotator that can rotate the polarization angle of an incident electromagnetic wave at the microwave frequency by 45 is presented. The polarization rotator is based on a two-dimensional periodic array of substrate integrated waveguide cavities, realizing the polarization rotation by coupling the input signal to the output wave through three metallic slots. Two layers of frequency selective surfaces are cascaded by substrate and form the polarization rotator. A vertical slot on the top layer is used to select the horizontal polarization from the incident wave, the vertical and the horizontal slots on the bottom layer are, respectively, used to obtain horizontally and vertically polarized outgoing waves. The two orthogonal outgoing waves are combined to result in the 45~ polarized wave. Both full wave simulation and experimental measurement are carried out, together validating the proposed method.

Electromagnetic Transmission Characteristics of Y-Shaped and Y-Ring-Shaped Frequency Selective Fabrics

Asymmetrical Y-shaped and Y-ring-shaped frequency selective fabrics(FSFs) were proposed in this paper. They were prepared by computer engraving technology and tested in the anechoic chamber by using the free-space method. The test results of representative samples show that the resonance frequencies and the resonance peak or valley values in two polarization modes are not completely identical but the differentials are small, indicating that the influences of polarization modes are not significant. The transmission coefficient curves of Y-shaped and Y-ring-shaped FSFs with various size parameters are obviously different. For instance, as the unit size D increases by 4.0 mm, the resonance frequencies of patch FSFs decrease by 1.92 GHz and the resonance valleys increase by 12.32 dB. Different size parameters have dissimilar effects on the transmission characteristics and the corresponding influence laws should be analyzed concretely. The work could provide reference for the structural design and characteristics analysis of other FSFs.