Microstructural Dependence of Friction and Wear Behavior in Biological Shells

As an essential renewable mineral resource,mollusk shells can be used as handicrafts,building materials,adsor-bents,etc.However,there are few reports on the wear resistance of their structures.The Vicker’s hardness and friction,and wear resistance of different microstructures in mollusk shells were comparatively studied in the pre-sent work.The hardness of prismatic structures is lower than that of cross-lamellar and nacreous structures.How-ever,the experimental results of sliding tests indicate that the prismatic structure exhibits the best anti-wear ability compared with foliated,crossed-lamellar,and nacreous structures.The anti-wear and hardness do not present a positive correlation,as the wear resistance properties of different microstructures in mollusk shells are governed jointly by organic matrix,structural arrangement,and basic building block actions.The present researchfindings are expected to provide fundamental insight into the design of renewable bionic materials with high wear resistance.

Friction and wear behavior and mechanism of low carbon microalloyed steel containing Nb

Dry sliding friction and wear test of Nb containing low carbon microalloyed steel was carried out at room temperature,and the effect of Nb on the wear behavior of the steel,as welll as the mechanism was studied.Scanning electron microscopy(SEM) and energy dispersive spectrometry(EDS) were employed to analyze the morphology and composition of the worn surface,and the structure evolution of the plastic deformation layer.The carbide content and type in the steel were analyzed by the electrolytic extraction device and X-ray diffraction(XRD).The experimental results demonstrate that the addition of 0.2% Nb can refine the grain and generate Nb C to improve the wear resistance of the steel.By enhancing the load and speed of wear experiment,the wear mechanism of the test steel with 0.2% Nb changes from slight oxidation wear to severe adhesion wear and oxidation wear.Compared with the load,the increase in the rotation speed exerts a greater influence on the wear of the test steel.

Exploring the Friction and Wear Properties of Silver Coatings on 718 Alloy

Fasteners of 718 alloys are used to set up connection between each support and other components for ITER system, metal-based Ag solid lubricant coating is widely used as an anti-seizure lubricant coating due to its strong low-temperature shear resistance. But the poor adhesion to the steel surfaces has been a critical restriction for applying the silver coatings to the practical machine elements. In this work, an 8-μm silver self-lubricating coating was deposited on the surface of 718 alloy by the method of magnetron sputtering. The coating was uniform, dense and consistent. The wear mechanism was investigated by analyzing the friction and wear properties of the coating. Stress is one of the important impacts on the friction coefficient, the results showed that it first increased and then decreased with the increase of pressure at room temperature and under vacuum. Temperature exerted an effect on the silver self-lubricating coating. A study was conducted under vacuum on the friction and wear performance of the coating at 300 K, 225 K, 155 K, and 77 K, respectively. The results showed that the wear mechanism and wear state varied under various low-temperature conditions, with the severity of wear reaching the maximum only at 225 K. Through the same silver coating process, the washer of superbolt was improved by silver coating treatment.

STUDY OF THE PERFORMANCE ON THE WEAR AND FRICTION OF THE C/Cu COMPOSITE MATERIAL

研究了Ｃ／Ｃｕ复合材料的摩擦磨损性能．通过在块－环型摩擦试验机上进行试验，得出在轻微磨损状态下，复合材料的摩擦系数和磨损率随压强增大而缓慢增大．电子显微镜观察和电子探针分析表明，摩擦面间形成了一层表面膜，这层膜具有一定的自润滑性和阻碍粘附发生的作用，这是使摩擦系数和磨损率保持较低水平的根本原因．

Dry Friction and Wear Characteristics of Impregnated Graphite in a Corrosive Environment

Tribological properties of impregnated graphite are greatly influenced by preparation technology and working conditions and it’s highly susceptible to corrosion environmental impacts,but the experimental research about it are few.In this paper,three kinds of impregnated graphite samples are prepared with different degree of graphitization,the tribological properties of these samples in the dry friction environment and in a corrosive environment are analyzed and contrasted.The tribo-test results show that the friction coefficient of samples is reduced and the amount of wear of samples increase when the graphitization degree of samples increases in dry friction condition.While in a corrosive environment（samples are soaked N2O4）,the friction coefficient and amount of wear are changed little if the graphitization degree of samples are low.If the degree of graphitization increase,the friction coefficient and amount of wear of samples increase too,the amount of wear is 2 to 3 times as the samples tested in the non-corrosive environment under pv value of 30MPa？m/s.The impregnated graphite,which friction coefficient is stable and graphitization degree is in mid level,such#2,is more appropriate to have a work in the corrosion conditions.In this paper,preparation and tribological properties especially in corrosive environment of the impregnated graphite is studied,the research conclusion can provide an experimental and theoretical basis for the selection and process improvement of graphite materials,and also provide some important design parameters for contact seal works in a corrosive environment.

Enhancement of wear and ballistic resistance of armour grade AA7075 aluminium alloy using friction stir processing

Industrial applications of aluminium and its alloys are restricted because of their poor tribological properties. Thermal spraying, laser surfacing, electron beam welding are the most widely used techniques to alter the surface morphology of base metal. Preliminary studies reveal that the coating and layering of aluminium alloys with ceramic particles enhance the ballistic resistance. Furthermore, among aluminium alloys,7075 aluminium alloy exhibits high strength which can be compared to that of steels and has profound applications in the designing of lightweight fortification structures and integrated protection systems. Having limitations such as poor bond integrity, formation of detrimental phases and interfacial reaction between reinforcement and substrate using fusion route to deposit hard particles paves the way to adopt friction stir processing for fabricating surface composites using different sizes of boron carbide particles as reinforcement on armour grade 7075 aluminium alloy as matrix in the present investigation. Wear and ballistic tests were carried out to assess the performance of friction stir processed AA7075 alloy. Significant improvement in wear resistance of friction stir processed surface composites is attributed to the change in wear mechanism from abrasion to adhesion. It has also been observed that the surface metal matrix composites have shown better ballistic resistance compared to the substrate AA7075 alloy. Addition of solid lubricant Mo S2 has reduced the depth of penetration of the projectile to half that of base metal AA7075 alloy. For the first time, the friction stir processing technique was successfully used to improve the wear and ballistic resistances of armour grade high strength AA7075 alloy.

Friction and Wear Characteristics of Mg-Al Alloy Containing Rare Earths

The influence of rare earth on the friction and wear characteristics of magnesium alloy AZ91 and AM60 were studied. The results show that the wear resistance properties of rare earth magnesium alloys are better than those of matrix alloy under the testing conditions. The anti wear behaviour of AZ91 alloy is much better than that of AM60 alloy. In dry sliding process,magnesium alloys undergo a transition from mild wear to severe wear. The addition of rare earths refine the structure of alloys, improve the comprehensive behaviors of magnesium alloys, increase the stability of oxidation films on worn surfaces, enhance the loading ability of rare earth magnesium alloys, and delay the transition from mild wear to severe wear effectively.

Friction and Wear Study on Friction Pairs with a Biomimetic Non-smooth Surface of 316L Relative to CF/PEEK under a Seawater Lubricated Condition

Current studies of a seawater axial piston pump mainly solve the problems of corrosion and wear in a slipper pair by selecting materials with corrosion resistance, self-lubrication, and wear resistance. In addition, an appropriate biomimetic non-smooth surface design for the slipper pair can further improve the tribological behavior. In this paper, 316 L stainless steel and CF/PEEK were selected to process the upper and bottom specimens, and the biomimetic non-smooth surface was introduced into the interface between the friction pair. The friction and wear tests were performed on a MMD-5 A tester at a rotation speed of 1000 r/min and load of 200 N under seawater lubricated condition. The results indicate that the main friction form of the smooth surface friction pair corresponds to abrasive wear and adhesive wear and that it exhibits a friction coe cient of 0.05–0.07, a specimen temperature of 56 ℃, a high wear rate, and surface roughness. Pits on the non-smooth surface friction pairs produced hydrodynamic lubrication and reduced abrasive wear, and thus the plowing e ect is their main friction form. The non-smooth surface friction pairs exhibit a friction coe cient of 0.03–0.04, a specimen temperature of 48 ℃, a low wear rate, and surface roughness. The study has important theoretical significance for enriching the lubrication, friction, and wear theory of a seawater axial piston pump, and economic significance and military significance for promoting the marine development and the national defense military.

Friction and Wear Performance of Boron Doped, Undoped Microcrystalline and Fine Grained Composite Diamond Films

Chemical vapor deposition （CVD） diamond films have attracted more attentions due to their excellent mechanical properties. Whereas as-fabricated traditional diamond films in the previous studies don＇t have enough adhesion or surface smoothness, which seriously impact their friction and wear performance, and thus limit their applications under extremely harsh conditions. A boron doped, undoped microcrystalline and fine grained composite diamond （BD-UM-FGCD） film is fabricated by a three-step method adopting hot filament CVD （HFCVD） method in the present study, presenting outstanding comprehensive performance, including the good adhesion between the substrate and the underlying boron doped diamond （BDD） layer, the extremely high hardness of the middle undoped microcrystalline diamond （UMCD） layer, as well as the low surface roughness and favorable polished convenience of the surface fine grained diamond （FGD） layer. The friction and wear behavior of this composite film sliding against low-carbon steel and silicon nitride balls are studied on a ball-on-plate rotational friction tester. Besides, its wear rate is further evaluated under a severer condition using an inner-hole polishing apparatus, with low-carbon steel wire as the counterpart. The test results show that the BD-UM-FGCD film performs very small friction coefficient and great friction behavior owing to its high surface smoothness, and meanwhile it also has excellent wear resistance because of the relatively high hardness of the surface FGD film and the extremely high hardness of the middle UMCD film. Moreover, under the industrial conditions for producing low-carbon steel wires, this composite film can sufficiently prolong the working lifetime of the drawing dies and improve their application effects. This research develops a novel composite diamond films owning great comprehensive properties, which have great potentials as protecting coatings on working surfaces of the wear-resistant and anti-frictional components.

The Friction and Wear Properties of the Spherical Plain Bearings with Self-lubricating Composite Liner in Oscillatory Movement

A test method based on the condition simulation and a friction and wear test machine featuring in oscillatory movement were set up for self-lubricating spherical plain bearings (SPB). In the machine the condition parameters such as load, angle and frequency of oscillation and number of test cycles can be properly controlled. The data relating to the tribological properties of the bearing, in terms of friction coefficient, linear wear amount, temperature near friction surface and applied load, can be monitored and recorded simultaneously during test process by a computerized measuring system of the machine. Efforts were made to improve the measurement technology of the friction coefficient in oscillating motion. In result, a well-designed bearing torque mechanism was developed, which could reveal the relation between the friction coefficient and the displacement of oscillating angle in any defined cycle while the curve of friction coefficient vs number of testing cycles was continuously plotted. The tribological properties and service life of four kinds of the bearings, i.e, the sampleⅠ-Ⅳ with different self-lubricating composite liners, including three kinds of polytetrafluoroethylene (PTFE) fiber weave/epoxy resin composite liners and a PTFE plastic/copper grid composite liner, were evaluated by testing, and the wear mechanisms of the liner materials were analyzed.

Friction and Wear Behaviors of Nanostructured Metals

Nanostructured （ns） materials, i.e., polycrystalline materials with grain sizes in the nanometer regime （typically below 100 nm）, have drawn considerable attention in the past decades due to their unique properties such as high strength and hardness. Wear resistance of ns materials, one of the most important properties for engineering materials, has been extensively investigated in the past decades. Obvious differences have been identified in friction and wear behaviors Between the ns materials and their corresponding coarse-grained （cg） counterparts, consistently correlating with their unique structure characteristics and mechanical properties. On the other hand, the superior tribological properties of ns materials illustrate their potential applications under contact loads. The present overview will summarize the important progresses achieved on friction and wear behaviors of ns metallic materials, including ultrafine-grained （ufg） materials in recent years. Tribological properties and effects on friction and wear behaviors of ns materials will be discussed under different wear conditions including abrasive wear, sliding wear, and fretting wear. Their correlations with mechanical properties will be analyzed. Perspectives on development of this field will be highlighted as well.

Influence of composition on friction-wear behavior of composite materi-als reinforced by brass fibers

In the study, for the composite materials reinforced by brass fibers, theinfluence of dominant ingredients, such as organic adhesion agent, cast iron debris, brass fiber,and graphite powder, on the friction-wear characteristics was investigated. The friction-wearexperiment was carried out on the block-on-ring tribometer MM 200. The worn surfaces of the frictionpair consisting of the composite materials and grey cast iron HT 200 under dry sliding frictionwere examined using scanning electron microscope (SEM), energy dispersive analysis (EDX) anddifferential thermal analysis-thermogravimetric analysis (DTA-TAG). The experimental results showedthat the friction coefficient and the wear loss of the composite material increase obviously withthe increase of cast iron debris content, but decrease obviously with the increase of graphitepowder content, and increase a little when the mass fraction of brass fiber was over 19 percent, andthe orientation of brass fiber has obvious influence on friction-wear property. When the massfraction of organic adhesion agent was about 10-11 percent, the composite materials have anexcellent friction-wear performance. The friction heat can pyrolyze organic ingredient in wornsurface layer.

Friction and Wear Behaviors of Ti/Cu/N Coatings on Titanium Alloy Surface by DC Magnetron Sputtering

Ti/Cu/N coatings with different Cu contents were deposited on titanium alloy surface by the DC magnetron sputtering technique.XPS and FESEM were employed to characterize the composition and structure of the coating on the Ti6A14 V substrates.In addition,The adhesion force,friction,and wear properties of the Ti/Cu/N coatings were investigated.The experimental results showed that the coarse particles of the coatings would grow more and the surface roughness increased with the increase of copper content in the coatings;The coatings showed a strong adhesion force;The friction coefficient of the coating of the samples was less than the substrate,reaching 0.19 at least.The wear resistance of the coatings could be improved by optimizing and controlling the relative content of Ti,Cu,N elements on the titanium alloy surface,especially the 10.98 at%contents of the copper.The sample C2 kept the best wear resistance.

Effect of Al2O3sf addition on the friction and wear properties of (SiCp+Al2O3sf)/Al2024 composites fabricated by pressure infiltration

Aluminum(Al) 2024 matrix composites reinforced with alumina short fibers(Al_2O_(3sf)) and silicon carbide particles(SiC_p) as wear-resistant materials were prepared by pressure infiltration in this study. Further, the effect of Al_2O_(3sf) on the friction and wear properties of the as-synthesized composites was systematically investigated, and the relationship between volume fraction and wear mechanism was discussed. The results showed that the addition of Al_2O_(3sf), characterized by the ratio of Al_2O_(3sf) to SiC_p, significantly affected the properties of the composites and resulted in changes in wear mechanisms. When the volume ratio of Al_2O_(3sf) to SiC_p was increased from 0 to 1, the rate of wear mass loss(K_m) and coefficients of friction(COFs) of the composites decreased, and the wear mechanisms were abrasive wear and furrow wear. When the volume ratio was increased from 1 to 3, the COF decreased continuously; however, the K_m increased rapidly and the wear mechanism became adhesive wear.

Friction and wear properties of copper matrix composites reinforced by tungsten-coated carbon nanotubes

Carbon nanotubes （CNTs） were coated by tungsten layer using metal organic chemical vapor deposition process with tungsten hexacarbonyl as a precursor. The W-coated CNTs （W-CNTs） were dispersed into Cu powders by magnetic stirring process and then the mixed powders were consolidated by spark plasma sintering to fabricate W-CNTs/Cu composites. The CNTs/Cu composites were fabricated using the similafprocesses. The friction coefficient and mass wear loss of W-CNTs/Cu and CNTs/Cu composites were studied. The results showed that the W-CNT content, interfacial bonding situation, and applied load could influence the friction coefficient and wear loss of W-CNTs/Cu com- posites. When the W-CNT content was 1.0 wt.%, the W-CNTs/Cu composites got the minimum friction coefficient and wear loss, which were decreased by 72.1% and 47.6%, respectively, compared with pure Cu specimen. The friction coefficient and wear loss of W-CNTs/Cu composites were lower than those of CNTs/Cu composites, which was due to that the interracial bonding at （W-CNTs）-Cu interface was better than that at CNTs-Cu interface. The friction coefficient of composites did not vary obviously with increasing applied load, while the wear loss of composites increased significantly with the increase of applied load.

Investigation of Micro-wear and Micro-friction Properties for Bionic Non-smooth Concave Components

Five kinds of 45# steel samples with concave features on the surface were manufactured using Laser Texturing Technology (LTT). Optimum design theory was used to design the experiment, and a two-level orthogonal table-L 16 (2 15 ) design was adopted . Micro-wear and micro-friction experienced by samples with concave surface features and samples with smooth surfaces were compared experimentally. The wear resistance of samples with concave surface features was increased most, and different surface morphologies had different effects on friction and wear properties.

Friction and wear behavior of Mg–11Y–5Gd–2Zn–0.5Zr(wt%)alloy with oil lubricant

The sliding friction and wear behaviors of Mg-11Y-5Gd-2Zn-0.5Zr （wt%） alloy were investigated under oil lubricant condition by pin-on-disk configuration with a constant sliding distance of 1,000 m in the temperature range of 25-200℃. Results indicate that the volumetric wear rates and average friction coefficients decrease with the increase of sliding speeds, and increase with the increase of test temperature below 150℃. The hard and thermally stable Mg12（Y,Gd）Zn phase with long-period stacking order structure in the alloy presents significant wear resistance, The wear mechanism below 100℃ is abrasive wear as a result of plastic extrusion deformation. The corporate effects of severe abrasive, oxidative, and delaminating wear result in the tribological mechanism above 100℃.

Effect of Extrusion Temperatures on Friction-wear Behavior of Chain-wheel Fabricated by 40Cr Steel under Oil-lubrication Condition

A 40Cr steel was formed into a chain-wheel using a warm extrusion technology. The surface roughness and micro-structure, micro-hardness and phases of the extruded samples at different temperatures were analyzed using a three-dimensional optical microscope (OM), micro-hardness tester, and X-ray diffraction (XRD), respectively. The morphologies, chemical element distributions and phases of worn tracks at the extrusion temperatures of 550, 650 and 750 °C were analyzed using a scanning electron microscopy (SEM), energy disperse spectroscopy (EDS), and XRD, respectively. The friction-wear behaviors of extruded samples under oil-lubrication condition were observed using a wear test. And the effects of extrusion temperatures on the wear mechanism were discussed. The results show that residual austenite and pearlite exist on the sample at the extrusion temperature of 550 °C with the corresponding grain size and surface micro-hardness of 32.7 nm and 370.33 HV, respectively. The average coefficient of friction (COF) of extruded sample at the temperature of 550 °C is 0.196 5, and the wear mechanism is fatigue and abrasive wear. While the acicular martensite exists on the extruded samples at the extrusion temperatures of 650 and 750 °C, the corresponding grain sizes are 30.0 and 29.1 nm, respectively. The average COF (coefficient of friction) of extruded sample at the temperatures of 650 and 750 °C are 0.187 4 and 0.163 6, respectively, and the wear mechanism is abrasive wear. As a result, the friction performance of extruded sample at the temperatures of 650 and 750 °C is better than that at the temperature of 550 °C.

The Friction and Wear of Sleeve-ring Pair Lubricated by Active Lubricants in the Presence of Magnetic Field

The effect of magnetic field on the tribological process of sleeve-ring pair lubricated by WRL lubricants was investigated by means of a NG-x wear tester and a PS5013 video microscope. The friction coefficient(f) and the wear weight(W) in lubricating test with WRL lubricant were decreased with the increase in the magnetic field vertical to the rubbing surface, and an almost zero wear lubricating situation was gained in a magnetic field of 1000A/m. The captured wear micro particles on the rubbing surface were observed in the testing process, and the theoretical analysis of magnetic effects was completed. It is indicated that the magnetic field has not only a capturing action of wear micro particles on the worn surface, but also a inducing polarization of magnetic anisotropy of lubricant molecular. The actions promote the absorption of WRL lubricant into the wear surface as well as wear micro-particles, so that a good tribological effect is obtained when both magnetic field and WRL present.

Friction and Wear Properties of TiAl and Ti_2AlN/TiAl Composites at High Temperature

The high-temperature friction and wear properties of TiAl alloys and Ti2AlN/TiAl composites （TTC） in contact with nickel-based superalloy were studied. The results showed that, at 800 and 1 000 ℃, the coefficient of the friction （COF） decreased with the increase of sliding velocity and the wear loss of the TTC decreased with the increase of volume fraction of Ti2AlN. The wear mechanisms of the pairs are adhesive wear and the wear debris mainly comes from the contacting nickel-based superalloy. The intergranular fracture and the cracking of the phase boundary in the lamellar structure are the wear mode of TiAl alloy. The wear mode of TTC is phase boundary fracture and adhesive spalling. The abrasive resistance of TTC is slightly higher than that of TiAl alloy.