The resin-matrix pantograph contact strip (RMPCS),which has excellent abrasion resistance with electrical current and friction-reducing function,was developed in view of the traditional contact strips with high mainte...The resin-matrix pantograph contact strip (RMPCS),which has excellent abrasion resistance with electrical current and friction-reducing function,was developed in view of the traditional contact strips with high maintenance cost,high wear rate with electrical current and severe damage to the copper conducting wire.The characteristics of worn surfaces,cross-section and typical elemental distributions of RMPCS were studied by scanning electron microscopy (SEM) and energy dispersion spectrometry (EDS).The wear behavior and arc discharge of RMPCS against copper were investigated with self-made electrical wear tester.The results show that the electrical current plays a critical role in determining the wear behavior,and the wear rate of the RMPCS against copper with electrical current is 2.7-5.8 times higher than the value without electrical current.The wear rate of the contact strip increases with the increase of the sliding speed and electrical current density.The main wear mechanism of RMPCS against copper without electrical current is low stress grain abrasive and slightly adhesive wear,while arc erosion wear and oxidation wear are the dominate mechanism with electrical current,which is accompanied by adhesive wear during the process of wear.展开更多
As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments ...As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.展开更多
CNTs-Ag-G electrical contact composite material was prepared by means of powder metallurgical method. The influence of the graphite content on sliding wear characteristics of electrical contact levels was examined. In...CNTs-Ag-G electrical contact composite material was prepared by means of powder metallurgical method. The influence of the graphite content on sliding wear characteristics of electrical contact levels was examined. In experiments, CNTs content was retained as 1% (mass fraction), and graphite was added at content levels of 8%, 10%, 13%, 15% and 18%, respectively. The results indicate that with the increase of graphite content, the contact resistance of electrical contacts is enhanced to a certain level then remains constant. Friction coefficient decreases gradually with the increase of graphite content. Wear mass loss decreases to the minimum value then increases. With the small content of graphite, the adhesive wear is hindered, which leads to the decrease of wear mass loss, while excessive graphite brings much more worn debris, resulting in the increase of mass loss. It is concluded that wear mass loss reaches the minimum value when the graphite mass fraction is about 13%. Compared with conventional Ag-G contact material, the wear mass loss of CNTs-Ag-G composite is much less due to the obvious increase of hardness and electrical conductivity, decline of friction surface temperature and inhibition of adhesive wear between composites and slip rings.展开更多
Sliding friction and wear experiments using Cu-La2O3-graphite composites against Cu-5 wt.%Ag alloy ring were conducted at a constant sliding speed of 10 m/s, a current density of 10 A/cm2 and a load of 2.5 N/cm2. Thes...Sliding friction and wear experiments using Cu-La2O3-graphite composites against Cu-5 wt.%Ag alloy ring were conducted at a constant sliding speed of 10 m/s, a current density of 10 A/cm2 and a load of 2.5 N/cm2. These composites with different La2O3 and graphite contents were fabricated by hot-pressing. Physical and mechanical properties of the composites were examined. Morphologies of the worn surface of composites were observed using optical microscopy. X-ray photoelectron spectroscopy spectra were used to study compositions of the lubricating film. The results showed that with the increasing addition of La2O3, hardness, flexural strength and electrical resistivity increased, but the relative density dropped. The friction coefficient increased with the increasing addition of La2O3. Composite containing 3 vol.% of La2O3 and 37 vol.% of graphite showed the best wear resistance. The main wear mechanisms of composites were abrasive wear, oxidative wear and adhesive wear.展开更多
基金Project (06FJ3041) supported by the Key Laboratory Open Foundation of Hunan Province, China
文摘The resin-matrix pantograph contact strip (RMPCS),which has excellent abrasion resistance with electrical current and friction-reducing function,was developed in view of the traditional contact strips with high maintenance cost,high wear rate with electrical current and severe damage to the copper conducting wire.The characteristics of worn surfaces,cross-section and typical elemental distributions of RMPCS were studied by scanning electron microscopy (SEM) and energy dispersion spectrometry (EDS).The wear behavior and arc discharge of RMPCS against copper were investigated with self-made electrical wear tester.The results show that the electrical current plays a critical role in determining the wear behavior,and the wear rate of the RMPCS against copper with electrical current is 2.7-5.8 times higher than the value without electrical current.The wear rate of the contact strip increases with the increase of the sliding speed and electrical current density.The main wear mechanism of RMPCS against copper without electrical current is low stress grain abrasive and slightly adhesive wear,while arc erosion wear and oxidation wear are the dominate mechanism with electrical current,which is accompanied by adhesive wear during the process of wear.
基金supported by Major Research Program of National Natural Science Foundation of China(Grant No. 91026018)National Natural Science Foundation of China(Grant No. 60979017)Doctoral Fund of Ministry of Education of China(Grant No. 20110111110015)
文摘As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.
基金Project(50271021) supported by the National Natural Science Foundation of ChinaProject(ZD2008003) supported by Key Science Foundation of the Education Department of Anhui Province, China+2 种基金Project(CF07-10) supported by the Innovation Center for Postgraduates at HFNL (USTC), ChinaProject(KF0702) supported by the Open Project Program of Ministry of Education of ChinaProject supported by Nippon Sheet Glass Foundation of Japan for Materials Science and Engineering
文摘CNTs-Ag-G electrical contact composite material was prepared by means of powder metallurgical method. The influence of the graphite content on sliding wear characteristics of electrical contact levels was examined. In experiments, CNTs content was retained as 1% (mass fraction), and graphite was added at content levels of 8%, 10%, 13%, 15% and 18%, respectively. The results indicate that with the increase of graphite content, the contact resistance of electrical contacts is enhanced to a certain level then remains constant. Friction coefficient decreases gradually with the increase of graphite content. Wear mass loss decreases to the minimum value then increases. With the small content of graphite, the adhesive wear is hindered, which leads to the decrease of wear mass loss, while excessive graphite brings much more worn debris, resulting in the increase of mass loss. It is concluded that wear mass loss reaches the minimum value when the graphite mass fraction is about 13%. Compared with conventional Ag-G contact material, the wear mass loss of CNTs-Ag-G composite is much less due to the obvious increase of hardness and electrical conductivity, decline of friction surface temperature and inhibition of adhesive wear between composites and slip rings.
基金Project supported by the Major Research Program of the National Natural Science Foundation of China(91026018)the Doctoral Fund of Ministry of Education of China(2011011110015)the Shanghai City special artificial micro materials and Technology Key Laboratory Open Fund(ammt2013A-7)
文摘Sliding friction and wear experiments using Cu-La2O3-graphite composites against Cu-5 wt.%Ag alloy ring were conducted at a constant sliding speed of 10 m/s, a current density of 10 A/cm2 and a load of 2.5 N/cm2. These composites with different La2O3 and graphite contents were fabricated by hot-pressing. Physical and mechanical properties of the composites were examined. Morphologies of the worn surface of composites were observed using optical microscopy. X-ray photoelectron spectroscopy spectra were used to study compositions of the lubricating film. The results showed that with the increasing addition of La2O3, hardness, flexural strength and electrical resistivity increased, but the relative density dropped. The friction coefficient increased with the increasing addition of La2O3. Composite containing 3 vol.% of La2O3 and 37 vol.% of graphite showed the best wear resistance. The main wear mechanisms of composites were abrasive wear, oxidative wear and adhesive wear.
