The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a seri...The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a series of tests on machine as EPMA, STM, DTG-DTA,an optical microscope and a friction test machine. The tests show that the rising rate in temperature and the heat conductivity of GFRF are lower than that of asbestos friction material. In GFRF, the heat-decline is slowed down or even eliminated. the distribution of heat- stress is improved and the life span is extended. Raising the temperature of resin resolution and enhancing the stickness between resin and glass fibre are the two important procedures to improve the friction and wear performance of GFRF.A discription about the friction and wear mechanism of GFRF is given in this paper.展开更多
Presentation of empirical equations for estimating engineering properties of soils is a simple, low cost and widely-used method. One of the major concerns in using these equations is evaluating their accuracy in diffe...Presentation of empirical equations for estimating engineering properties of soils is a simple, low cost and widely-used method. One of the major concerns in using these equations is evaluating their accuracy in different conditions and regions which often lead to doubts about obtained results. Most of these equations were derived in special laboratories, different climate conditions and in soils with different geotechnical and geological engineering properties and were generalized to other conditions. The main question is that whether these methods are also applicable to other conditions. Using local equations and narrowing the usage range of various methods based on each region’s properties are appropriate methods to solve these problems. This leads to simplified and faster analysis and high reliability in the obtained results. In this paper, empirical equations were derived to estimate internal friction angle, based on SPT numbers of Mashhad City’s soils in Iran, using SPT and direct shear tests results from 50 samples (25 GW and 25 GC soil samples). The results showed similar values for predicted?φ?values by SPT test and?φ?values determined by direct shear tests.展开更多
Friction spun core yarn has two components: filament core and staple fiber sheath. Under axial rubbing action, the failure mode of the core yarn is the stripping of the sheath from the core. This paper introduces a me...Friction spun core yarn has two components: filament core and staple fiber sheath. Under axial rubbing action, the failure mode of the core yarn is the stripping of the sheath from the core. This paper introduces a method to test the anti - stripping property of the core yarn. With a modified Universal Testing Machine, the stripping resistance of friction spun core yarn can be continuously measured. Some factors Influencing the measurements are discussed in detail. The testing results are compared with those from a Y731 Yarn Abrasion Tester and fur - ther confirmed by weaving practice.展开更多
Current work is focused on the influence of friction in deep drawing process. Friction measurements were also conducted using a modified tribotester based on strip sliding between tools. Four different tool surfaces w...Current work is focused on the influence of friction in deep drawing process. Friction measurements were also conducted using a modified tribotester based on strip sliding between tools. Four different tool surfaces were tested under similar contact conditions regarding contact area, normal pressure, sliding speed, lubricant and surface characteristics to calculate the friction coefficient between the tool surface and a high strength low alloy steel sheet HSLA 380. The results showed that friction coefficient varies over a wide range with different lubricating conditions and different sliding velocities. For some sliding velocities, the coefficient of friction is stable and low, while for others it is unstable and higher. Results of the experiments reveal that this novel tribotester is a very useful tool to evaluate and compare the friction between steel sheet and tool surfaces in alloyed steel for cold working applications. The outcomes have only small dispersion within the different test series, which indicates a stable process with good repeatability. The test method enables comparison of different surface finishes and treatments, lubricants and coatings in terms of friction and galling under conditions similar to those found in sheet metal forming processes. The four different types of surfaces considered for this study were grinded, polished, nitrided and quenched/tempered. The main difference among the tested tools in this work was the surface roughness, which was found to have a strong influence on friction.展开更多
文摘The relationships between the microstructure, the composition, the friction temperature and the form of a new kind of friction material which is a glass fibre resin friction materials (GFRF) are studied through a series of tests on machine as EPMA, STM, DTG-DTA,an optical microscope and a friction test machine. The tests show that the rising rate in temperature and the heat conductivity of GFRF are lower than that of asbestos friction material. In GFRF, the heat-decline is slowed down or even eliminated. the distribution of heat- stress is improved and the life span is extended. Raising the temperature of resin resolution and enhancing the stickness between resin and glass fibre are the two important procedures to improve the friction and wear performance of GFRF.A discription about the friction and wear mechanism of GFRF is given in this paper.
文摘Presentation of empirical equations for estimating engineering properties of soils is a simple, low cost and widely-used method. One of the major concerns in using these equations is evaluating their accuracy in different conditions and regions which often lead to doubts about obtained results. Most of these equations were derived in special laboratories, different climate conditions and in soils with different geotechnical and geological engineering properties and were generalized to other conditions. The main question is that whether these methods are also applicable to other conditions. Using local equations and narrowing the usage range of various methods based on each region’s properties are appropriate methods to solve these problems. This leads to simplified and faster analysis and high reliability in the obtained results. In this paper, empirical equations were derived to estimate internal friction angle, based on SPT numbers of Mashhad City’s soils in Iran, using SPT and direct shear tests results from 50 samples (25 GW and 25 GC soil samples). The results showed similar values for predicted?φ?values by SPT test and?φ?values determined by direct shear tests.
文摘Friction spun core yarn has two components: filament core and staple fiber sheath. Under axial rubbing action, the failure mode of the core yarn is the stripping of the sheath from the core. This paper introduces a method to test the anti - stripping property of the core yarn. With a modified Universal Testing Machine, the stripping resistance of friction spun core yarn can be continuously measured. Some factors Influencing the measurements are discussed in detail. The testing results are compared with those from a Y731 Yarn Abrasion Tester and fur - ther confirmed by weaving practice.
文摘Current work is focused on the influence of friction in deep drawing process. Friction measurements were also conducted using a modified tribotester based on strip sliding between tools. Four different tool surfaces were tested under similar contact conditions regarding contact area, normal pressure, sliding speed, lubricant and surface characteristics to calculate the friction coefficient between the tool surface and a high strength low alloy steel sheet HSLA 380. The results showed that friction coefficient varies over a wide range with different lubricating conditions and different sliding velocities. For some sliding velocities, the coefficient of friction is stable and low, while for others it is unstable and higher. Results of the experiments reveal that this novel tribotester is a very useful tool to evaluate and compare the friction between steel sheet and tool surfaces in alloyed steel for cold working applications. The outcomes have only small dispersion within the different test series, which indicates a stable process with good repeatability. The test method enables comparison of different surface finishes and treatments, lubricants and coatings in terms of friction and galling under conditions similar to those found in sheet metal forming processes. The four different types of surfaces considered for this study were grinded, polished, nitrided and quenched/tempered. The main difference among the tested tools in this work was the surface roughness, which was found to have a strong influence on friction.
