Furfurylated wood exhibits excellent dimensional stability and corrosion resistance,making it a promising material for constructing buildings,but it is highly flammable.Herein,flame-retardant furfurylated poplar wood ...Furfurylated wood exhibits excellent dimensional stability and corrosion resistance,making it a promising material for constructing buildings,but it is highly flammable.Herein,flame-retardant furfurylated poplar wood was produced via a two-step process utilizing boric acid(BA)and ammonium dihydrogen phosphate(ADP)as flame-retardant components,and biomass-derived furfuryl alcohol(FA)as a modifier.The acidity of BA and ADP allowed them to catalyze the polymerization of FA,which formed a cross-linked network that immobilized BA and ADP inside the wood.The addition of BA/ADP substantially delayed the time to ignition from 10 to 385 s and reduced the total heat release and total smoke release by 58.75%and 77.31%,respectively.Analysis of the pyrolysis process showed that the decomposition products of BA and ADP protected the underlying furfurylated wood and diluted combustible gases.This method significantly improved the fire retardancy and smokeless properties of furfurylated wood,providing promising prospects for its application as an engineering material.展开更多
A robust and green strategy for the selective upgrading of biomass-derived platform chemicals towards highly valuable products is important for the sustainable development.Herein,the efficient electrocatalytic oxidati...A robust and green strategy for the selective upgrading of biomass-derived platform chemicals towards highly valuable products is important for the sustainable development.Herein,the efficient electrocatalytic oxidation of biomass-derived furfuryl alcohol(FFA)into furoic acid(FurAc)catalyzed by the electrodeposited non-precious NiFe microflowers was successfully reached under the low temperature and ambient pressure.The 3D hierarchical NiFe microflowers assembled from ultrathin nanosheets were controllably synthesized by the electrodeposition method and uniformly grown on carbon fiber paper(CFP).Electrochemical analysis confirmed that NiFe nanosheets more preferred in the selective oxidation of FFA(FFAOR)than oxygen evolution reaction(OER).The linear sweep voltammetry(LSV)in FFAOR displayed a clear decrease towards lower potential,resulting in 30 mV reduction of overpotential at 20 mA cm^(-2) compared with that of OER.The optimal catalyst Ni_(1)Fe_(2) nanosheets exhibited the highest selectivity of FurAc(94.0%)and 81.4%conversion of FFA within 3 h.Besides,the influence of various reaction parameters on FFAOR was then explored in details.After that,the reaction pathway was investigated and rationally proposed.The outstanding performance for FFAOR can be ascribed to the unique structure of 3D flower-like NiFe nanosheets and oxygen vacancies,resulting in large exposure of active sites,faster electron transfer and enhanced adsorption of reactants.Our findings highlight a facile and convenient mean with a promising green future,which is promising for processing of various biomass-derived platform chemicals into value-added products.展开更多
Furfurylation is a well-known wood modification technology.This paper studied the effect of tannin addition on the wood furfurylation.Three kinds of dicarboxylic acids,adipic acid,succinic acid,and tartaric acid,as we...Furfurylation is a well-known wood modification technology.This paper studied the effect of tannin addition on the wood furfurylation.Three kinds of dicarboxylic acids,adipic acid,succinic acid,and tartaric acid,as well as glyoxal as a comparing agent,were used to catalyse the polymerisation of furanic or tannin-furanic solutions during wood modification.Impregnation of furanic or tannin-furanic solution at a certain concentration into the wood followed with curing at 103℃for a specific duration was performed for the wood modification.Different properties of the modified woods like dimensional stability,resistance of treatment to leaching,mechanical properties,decay durability against white-rot(Coriolus versicolor,Pycnoporus sanguineus)and brown-rot(Coniophora puteana)as well as their chemical and anatomical characteristics were evaluated.Results revealed that the partial substitution of FA by the tannins improved the fixation of the chemicals impregnated in wood.Further,dimensional stability,leaching resistance,Brinell hardness,modulus of elasticity/modulus of rupture,and decay durability properties of the furfurylated wood were also improved in the presence of tannins.Scanning electron microscopy revealed the deposition of the polymer in the wood lumen cells and in the wood cell walls.展开更多
Cu nanoparticles supported on a variety of oxide supports, including SiO2, TiO2, ZrO2, Al2O3, MgO and ZnO, were investigated for the hydrogenolysis of biomass‐derived furfuryl alcohol to1,2‐pentanediol and 1,5‐pent...Cu nanoparticles supported on a variety of oxide supports, including SiO2, TiO2, ZrO2, Al2O3, MgO and ZnO, were investigated for the hydrogenolysis of biomass‐derived furfuryl alcohol to1,2‐pentanediol and 1,5‐pentanediol. A Cu‐Al2O3 catalyst with 10 wt% Cu loading prepared by a co‐precipitation method exhibited the best performance in terms of producing pentanediols compared with the other materials. This catalyst generated an 85.8% conversion and a 70.3% combined selectivity for the target pentanediols at 413 K and 8 MPa H2 over an 8‐h reaction. The catalyst could also be recycled over repeated reaction trials without any significant decrease in productivity. Characterizations with X‐ray diffraction, NH3/CO2‐temperature programmed desorption, N2 adsorption,transmission electron microscopy and N2 O chemisorption demonstrated that intimate and effective interactions between Cu particles and the acidic Al2O3 support in this material greatly enhanced its activity and selectivity. The promotion of the hydrogenolysis reaction was found to be especially sensitive to the Cu particle size, and the catalyst with Cu particles 1.9 to 2.4 nm in size showed the highest turnover frequency during the synthesis of pentanediols.展开更多
Selective hydrogenolysis of biomass‐derived furfuryl alcohol(FFA)to 1,5‐and 1,2‐pentanediol(PeD)was conducted over Cu‐LaCoO3 catalysts with different Cu loadings;the catalysts were derived from perovskite structur...Selective hydrogenolysis of biomass‐derived furfuryl alcohol(FFA)to 1,5‐and 1,2‐pentanediol(PeD)was conducted over Cu‐LaCoO3 catalysts with different Cu loadings;the catalysts were derived from perovskite structures prepared by a one‐step citrate complexing method.The catalytic performances of the Cu‐LaCoO3 catalysts were found to depend on the Cu loading and pretreatment conditions.The catalyst with 10 wt%Cu loading exhibited the best catalytic performance after prereduction in 5%H2‐95%N2,achieving a high FFA conversion of 100%and selectivity of 55.5%for 1,5‐pentanediol(40.3%)and 1,2‐pentanediol(15.2%)at 413 K and 6 MPa H2.This catalyst could be reused four times without a loss of FFA conversion but it resulted in a slight decrease in pentanediol selectivity.Correlation between the structural changes in the catalysts at different states and the simultaneous variation in the catalytic performance revealed that cooperative catalysis between Cu0 and CoO promoted the hydrogenolysis of FFA to PeDs,especially to 1,5‐PeD,while Co0 promoted the hydrogenation of FFA to tetrahydrofurfuryl alcohol(THFA).Therefore,it is suggested that a synergetic effect between balanced Cu0 and CoO sites plays a critical role in achieving a high yield of PeDs with a high 1,5‐/1,2‐pentanediol selectivity ratio during FFA hydrogenolysis.展开更多
The conversion of hemicellulose-derived xylose to furfuryl alcohol is a practical procedure for producing value-added chemicals from biomass.In this study,a bifunctional Cu/SBA-15-SO3 H catalyst was employed for the o...The conversion of hemicellulose-derived xylose to furfuryl alcohol is a practical procedure for producing value-added chemicals from biomass.In this study,a bifunctional Cu/SBA-15-SO3 H catalyst was employed for the one-pot catalytic conversion of xylose to furfuryl alcohol with a yield of up to 62.6% at the optimized conditions of 140℃,4 MPa,and for 6 h in a biphasic water/n-butanol solvent.A high reaction temperature resulted in further hydrogenation to 2-methyl furan,while a high hydrogen pressure led to a side hydrogenation reaction to xylitol.The biphasic solvent allowed xylose solvation as well as furfuryl product extraction.The acidic-SO3 H sites and Cu sites co-existed,maintained a balance,and cooperatively catalyzed the cascade conversion.Excessive acidic sites and large pores could promote the xylose conversion,although a low furfuryl alcohol yield was obtained.This catalytic system could be potentially applied to the one-pot synthesis of furfuryl alcohol from hemicellulose-derived xylose.展开更多
Silicoaluminophosphate-34(SAPO-34) molecular sieves have important applications in the petrochemical industry as a result of their shape selectivity and suitable acidity. In this work, nanoaggregate SAPO-34 with a lar...Silicoaluminophosphate-34(SAPO-34) molecular sieves have important applications in the petrochemical industry as a result of their shape selectivity and suitable acidity. In this work, nanoaggregate SAPO-34 with a large external surface area was obtained by dissolving pseudoboehmite and tetraethylorthosilicate in an aqueous solution of tetraethylammonium hydroxide and subsequently adding phosphoric acid. After hydrolysis in an alkaline solution, the aluminum and silicon precursors exist as Al(OH)4-and SiO2(OH)-, respectively;this is beneficial for rapid nucleation and the formation of nanoaggregates in the following crystallization process. Additionally, to study the effect of the external surface area and pore size on the catalytic performance of different SAPO-34 structures, the alcoholysis of furfuryl alcohol to ethyl levulinate(EL) was chosen as a model reaction. In a comparison with the traditional cube-like SAPO-34, nanoaggregate SAPO-34 generated a higher yield of 74.1% of EL, whereas that with cube-like SAPO-34 was only 19.9%. Moreover, the stability was remarkably enhanced for nanoaggregate SAPO-34. The greater external surface area and larger number of external surface acid sites are helpful in improving the catalytic performance and avoiding coke deposition.展开更多
At present, furan resin is the largest selling no-bake system of moulding sands. The most commonly used furan no-bake binders(FNB) are condensation products of furfuryl alcohol(FA) urea, formaldehyde and phenol. They ...At present, furan resin is the largest selling no-bake system of moulding sands. The most commonly used furan no-bake binders(FNB) are condensation products of furfuryl alcohol(FA) urea, formaldehyde and phenol. They are generally cured by exposure to organic sulfonic acids. FNB provide excellent mold and core strength, cure rapidly and allow the sand to be reclaimed at fairly high yields, generally 75%-80%, especially in applications where due allowance is made for the need to keep total sulfur content below 0.1%. However, due to probable carcinogenic properties of furfuryl alcohol, the EU Directive limits the content of this substance(in a monomer form in resin) to 25%. The classification of furfuryl alcohol and the resulting furan resin products has changed from "harmful" to "toxic by inhalation". The aim of this study was to determine the effect of free furfuryl alcohol content in the resin on the emission of harmful substances from the BTEX(Benzene Toluene Ethylbenzene & Xylene) and PAHs(polycyclic aromatic hydrocarbon) group exposed to high temperature and how it affects the emissions allowance of reclaimed sand in the matrix. Three resins from a leading manufacturer were examined, which contain a free furfuryl alcohol content of 71%-72%, about 50% and < 25%, respectively. The hardener for each resin was 65% aqueous solution of paratoluenesulfonic acid. Tests were carried out in semi-industrial conditions where liquid cast-iron was poured into sample sand mold at 1,350 °C. The matrix of the studied sands was reclaimed in the amount of 0, 50%, 100%, respectively.With the increase of free furfuryl alcohol content, the volume of evolved gases decreased. For all resins the main component from the BTEX group dominating in the emitted gases was benzene; however toluene also appeared in the amount of a few percentages. In contrast, ethylbenzene and xylenes occurred only in the gases emitted from resin-bonded sands with the largest furfuryl alcohol content. The increase in the share of reclaimed sands resulted in very significant increase in the volume of gas generated and participation of benzene in these gases. In terms of emission of compounds from the PAHs group virtually for all resins, the total content of these substances was comparable(within the limits of error). The main components were: fluoranthene, pyrene and benzo(a) anthracene.展开更多
Based on a special synthesis process of furan resin,the furfuryl alcohol(FA),the main component of typical no-bake furan resins is substituted by ethanol and xylitol mother liquor which is relatively low price and che...Based on a special synthesis process of furan resin,the furfuryl alcohol(FA),the main component of typical no-bake furan resins is substituted by ethanol and xylitol mother liquor which is relatively low price and chemically active.Through orthogonal test,the optimal amount of xylitol liquor,ethanol and modifier has been determined.Finally,the test results on technical properties show that the performance can meet the production requirement well,which indicate a success in this substituting attempt.展开更多
The Ni(Ⅱ) complex with ligand 2-N-(2-hydroxy-benzylidene) furanmethanoamine has been synthesized and characterized by elemental analysis, IR and single-crystal X-ray diffraction. It crystallizes in the monoclinic...The Ni(Ⅱ) complex with ligand 2-N-(2-hydroxy-benzylidene) furanmethanoamine has been synthesized and characterized by elemental analysis, IR and single-crystal X-ray diffraction. It crystallizes in the monoclinic system, space group C2/c with a = 2.0280(4), b =0.57700(12), c = 1.7340(4) nm, β = 94.74(3)°, Z = 4, Dc = 1.508 g/cm^3, the final R = 0.0434 and wR = 0.1112 for 1843 observed reflections with 1 〉 2σ(I). X-ray analysis revealed that the Ni(Ⅱ) ion is coordinated by two nitrogen atoms of Schiff base and two oxygen atoms of salicylaldehyde in the equatorial plane, and the coordination geometry can be described as a square.展开更多
An effect of phase compositions(rutile,Rut and anatase,Ant)of TiO_(2)supports on the selective hydrogenation of furfural to furfuryl alcohol was investigated.The 15%wt Ni/TiO_(2)catalysts were prepared by incipient im...An effect of phase compositions(rutile,Rut and anatase,Ant)of TiO_(2)supports on the selective hydrogenation of furfural to furfuryl alcohol was investigated.The 15%wt Ni/TiO_(2)catalysts were prepared by incipient impregnation method.The result showed that Ni supported on anatase-rutile mixed phase TiO_(2)(91%Rut and 9%Ant,A2)provided the highest furfuryl alcohol yield at 43.8%due to the relatively strong Ni-TiO_(2)interaction,its appropriate crystallite sizes,and high average pore sizes.Furthermore,the effect of cobalt as a promoter on Ni/TiO_(2)-A2 catalysts was studied.The result showed that the Ni-Co/TiO_(2)-A2 catalysts exhibited poorer catalyst performances compared to the monometallic Ni/TiO_(2),probably because addition of cobalt can lower the reduction temperatures of Ni/TiO_(2)and weaken the metal-support interaction.展开更多
The catalytic transformation of furfuryl alcohol and hexose into value-added chemicals have been investigated with a series of polymer-based catalysts including poly(styrenesulfonic acid)(PSS),graphite oxide-doped pol...The catalytic transformation of furfuryl alcohol and hexose into value-added chemicals have been investigated with a series of polymer-based catalysts including poly(styrenesulfonic acid)(PSS),graphite oxide-doped poly(styrenesulfonic acid)(PSS-GO),and graphite-doped poly(-styrenesulfonic acid)(PSS-C).It is found that the selective conversion of furfuryl alcohol to methyl levulinate(MLE)was successfully performed with PSS as the catalyst,in which a 96.4%yield is attained in methanol solvent.Moreover,the efficient dehydration of D-fructose to produce 5-hydroxymethylfurfural(HMF)has also been achieved using PSS-GO as the catalyst,where a 76.5%yield of HMF was obtained in Nmethylpyrrodinone solvent.The effects of reaction temperature,time and solvent were investigated.Furthermore,the used catalysts have been respectively characterized by XRD,TG,FTIR,SEM and TEM techniques to reveal the physical properties and structures of these polymeric catalytic materials.展开更多
The synthesis of a low cost no-bake furan resin with a high strength was researched in this paper. Through the analysis of main factors influencing the strength of furan resin, an orthogonal experiment was conducted t...The synthesis of a low cost no-bake furan resin with a high strength was researched in this paper. Through the analysis of main factors influencing the strength of furan resin, an orthogonal experiment was conducted to optimize synthesis of urea-formaldehyde furan resin with 3% nitrogen. The critical factors and their optimal levels were confirmed, and high strength property was obtained. Subsequently, some active substitute materials, including polyols A agent, methyl alcohol, mother liquid of xylitol, polyols B agent and ethanol, were used for partly substitution of furfural alcohol, the main material component of furan resin. A good combination of the substitute materials was determined to achieve a high strength, and the overal proportion of substitute materials to the resin is 20%. In this study, the substitution mechanism on furan resin was also characterized and analyzed by IR.展开更多
Simple bio-based abrasive grinding wheel based on thermosetting resin matrix was developed starting with condensed tannin and furfuryl alcohol,which are mainly derived from forest and agricultural products like tree b...Simple bio-based abrasive grinding wheel based on thermosetting resin matrix was developed starting with condensed tannin and furfuryl alcohol,which are mainly derived from forest and agricultural products like tree barks,wheat and crops.Fourier transform infrared spectra(FTIR)signified the acidic conditions are quiet efficient for the reaction of furfuryl alcohol,urea and glyoxal all together and the-CH_(2)-NH-and-CH_(2)-O-CH(OH)-groups are predominating in cross-linking of the tannin-furfuryl alcohol-urea-glyoxal(TFUG)resin.The strengthening contribution of the tannin was also confirmed by the preservation of its distinct crystallinity using X-ray diffraction(XRD).Differential scanning calorimetry(DSC)and thermogravimetric analysis(TGA)ensured that TFUG resin can be cured at low temperature and offer higher heat resistance compared with phenol-formaldehyde(PF)resin.The high hardness and excellent compressive strength revealed by the corresponding investigations such as Brinell hardness,compression resistance,and grinding tests suggested a strong abrasive ability using the new grinding wheel compared with lab-made grinding wheel based on PF resin.This could be ascribed to the absence of cracks and low content of formed holes as confirmed using scanning electron microscopy(SEM)and balanced reaction conditions that leads to network structure with regular local reinforcements and homogeneous crosslink density.展开更多
A theoretical study of poly furfuryle alcohol (PFA), rhodamine B (Rh B) dye and their blends (PFA-Rh B) is carried out by using the density functional theory (DFT). Electronic states and opto-electronic properties are...A theoretical study of poly furfuryle alcohol (PFA), rhodamine B (Rh B) dye and their blends (PFA-Rh B) is carried out by using the density functional theory (DFT). Electronic states and opto-electronic properties are investigated. The electronic states indicate that the oligomers of FA are insulators and Rh B is a wide band gap semiconductor. Their blends have a narrow band gap of about 0.75 eV. The optoelectronic properties are studied using TDDFT, which indicates that the chain length of poly furfuryl alcohol is an effective parameter to control both energies and intensities of absorption in which longer chain causes absorption with high intensity within long wavelength. A single broad baned of electron excitations is more like 8-oligomer-RhB case, which centers at wavelengths about 599 nm and 625 nm. This band of absorption covers the whole visible region of spectrum.展开更多
Vapor-phase transformations of furfural over SBA-15 silica supported Ni catalysts under H<sub>2</sub> in a continuous-flow reactor at atmospheric pressure and 170°C and 230°C were investiga...Vapor-phase transformations of furfural over SBA-15 silica supported Ni catalysts under H<sub>2</sub> in a continuous-flow reactor at atmospheric pressure and 170°C and 230°C were investigated. Two different samples having Ni loadings of 5 and 20 wt% (denoted here by SBA-5Ni and SBA-20Ni, respectively) were prepared by impregnation and characterized by atomic absorption spectroscopy, N<sub>2</sub> sorption analysis, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. Furan and furfuryl alcohol were two primary products resulting, respectively, from decarbonylation and hydrogenation of furfural. Under the conditions of the study, both reactions exhibited structure sensitivity evidenced by changes in product selectivities with variable Ni loadings. Compared with SBA-20Ni, the 5 wt% Ni catalyst showed better catalytic activity, reaching a furfural conversion of 100 mol% and a selectivity to furan of 98 mol%, after 5 h of time-on-stream at 230°C.展开更多
Selective activation of C-O bond is of fundamental importance in the precise conversion of oxygenates into value-added compounds in an atom-economic and sustainable manner, and meanwhile, the structurally well-defined...Selective activation of C-O bond is of fundamental importance in the precise conversion of oxygenates into value-added compounds in an atom-economic and sustainable manner, and meanwhile, the structurally well-defined dual-atoms catalysts (DACs) have been scarcely investigated in this field. In this study, a series of transition metal DACs anchored on nitrogen-doped graphene (TM2/NC, TM=Pt, Ir, Rh, Pd, Ru, Co, Ni and Cu) was constructed to make a comprehensive investigation of their selectivity in the hydrogenative transformation of furfuryl alcohol (FAL), an important biomass platform molecule, to 1,2-pentanediol (1,2-PeD) via selective cleavage of furanic C5-O bond, by density functional theory (DFT) calculations and microkinetic modeling. We found that Ir2/NC demonstrated a high selectivity for the cleavage of furanic C5-O bond to produce 1,2-PeD, while the production of THFAL or 1,5-pentanediol (1,5-PeD) on other TM2/NC catalysts are more favorable. Furthermore, we found that the selective C-O bond cleavage of FAL furan ring is affected by the orbital overlap between the d-orbitals of the anchored metal atoms and the p-orbitals of the adsorbed C atom in FAL, suggesting that the selectivity of the C-O bond cleavage is inextricably related with the electronic property of the anchored metals.展开更多
Bimetallic CuCo catalysts with different Cu to Co ratios on N-doped porous carbon materials(N-C)were achieved using impregnation method and applied in the hydrogenation of furfural(FAL)to furfuryl alcohol(FOL).The hig...Bimetallic CuCo catalysts with different Cu to Co ratios on N-doped porous carbon materials(N-C)were achieved using impregnation method and applied in the hydrogenation of furfural(FAL)to furfuryl alcohol(FOL).The high hydrogenation activity of FAL over Cu_(1)Co_(1)/N-C was originated from the synergistic interactions of Cu and Co species,where Co^(0)and Cu^(0)simultaneously adsorb and activate H_(2),and Cu^(+) served as Lewis acid sites to activate C]O.Meanwhile,electrons transfer from Cu to Co promoted the formation of Cu^(+).In situ Fourier transform infrared spectroscopy analysis indicated that Cu_(1)Co_(1)/N-C adsorbed FAL with a tilted η^(1)-(O)configuration.The superior Cu_(1)Co_(1)/N-C showed excellent adsorbed ability towards H_(2) and FAL,but weak adsorption for FOL.Therefore,Cu_(1)Co_(1)/N-C possessed 93.1%FAL conversion and 99.0% FOL selectivity after 5 h reaction,which also exhibited satisfactory reusability in FAL hydrogenation for five cycles.展开更多
Catalytic transfer hydroge nation(CTH)of furfural(FF)to furfu ryl alcohol(FFA)has received great intere st in recent years.He rein,Cu-Cs bimetallic supported catalyst,CuCs(2)-MCM,was developed for the CTH of FF to FFA...Catalytic transfer hydroge nation(CTH)of furfural(FF)to furfu ryl alcohol(FFA)has received great intere st in recent years.He rein,Cu-Cs bimetallic supported catalyst,CuCs(2)-MCM,was developed for the CTH of FF to FFA using formic as hydrogen donor.CuCs(2)-MCM achieved a 99.6%FFA yield at an optimized reaction conditions of 170℃,1 h.Cu species in CuCs(2)-MCM had dual functions in catalytically decomposing formic acid to generate hydrogen and hydrogenating FF to FFA.The doping of Cs made the size of Cu particles smaller and improved the dispersion of the Cu active sites.Impo rtantly,the Cs species played a favorable role in enhancing the hydrogenation activity as a promoter by adjusting the surface acidity of Cu species to an appropriate level.Correlation analysis showed that surface acidity is the primary factor to affect the catalytic activity of CuCs(2)-MCM.展开更多
基金financially supported by the Key Research and Development Program of Hunan Province,China(2023NK2038)National Natural Science Foundation of China(32201485)+2 种基金Natural Science Foundation of Hunan Province,China(2022JJ40863,2023JJ60161)Scientific Research Project of Hunan Provincial Education Department,China(21B0238,22A0177)Hunan Provincial Technical Innovation Platform and Talent Program in Science and Technology,China(2023RC3159).
文摘Furfurylated wood exhibits excellent dimensional stability and corrosion resistance,making it a promising material for constructing buildings,but it is highly flammable.Herein,flame-retardant furfurylated poplar wood was produced via a two-step process utilizing boric acid(BA)and ammonium dihydrogen phosphate(ADP)as flame-retardant components,and biomass-derived furfuryl alcohol(FA)as a modifier.The acidity of BA and ADP allowed them to catalyze the polymerization of FA,which formed a cross-linked network that immobilized BA and ADP inside the wood.The addition of BA/ADP substantially delayed the time to ignition from 10 to 385 s and reduced the total heat release and total smoke release by 58.75%and 77.31%,respectively.Analysis of the pyrolysis process showed that the decomposition products of BA and ADP protected the underlying furfurylated wood and diluted combustible gases.This method significantly improved the fire retardancy and smokeless properties of furfurylated wood,providing promising prospects for its application as an engineering material.
基金supported by Key Area Research and Development Program of Guangdong Province (2019B110209003)Guangdong Basic and Applied Basic Research Foundation (2019B1515120058,2020A1515011149)+2 种基金National Natural Science Foundation of China (22078374,21776324)National Key R&D Program of China (2018YFD0800703)National Ten Thousand Talent Plan,the Fundamental Research Funds for the Cornell University (19lgzd25)and Hundred Talent Plan (201602)from Sun Yat-sen University.
文摘A robust and green strategy for the selective upgrading of biomass-derived platform chemicals towards highly valuable products is important for the sustainable development.Herein,the efficient electrocatalytic oxidation of biomass-derived furfuryl alcohol(FFA)into furoic acid(FurAc)catalyzed by the electrodeposited non-precious NiFe microflowers was successfully reached under the low temperature and ambient pressure.The 3D hierarchical NiFe microflowers assembled from ultrathin nanosheets were controllably synthesized by the electrodeposition method and uniformly grown on carbon fiber paper(CFP).Electrochemical analysis confirmed that NiFe nanosheets more preferred in the selective oxidation of FFA(FFAOR)than oxygen evolution reaction(OER).The linear sweep voltammetry(LSV)in FFAOR displayed a clear decrease towards lower potential,resulting in 30 mV reduction of overpotential at 20 mA cm^(-2) compared with that of OER.The optimal catalyst Ni_(1)Fe_(2) nanosheets exhibited the highest selectivity of FurAc(94.0%)and 81.4%conversion of FFA within 3 h.Besides,the influence of various reaction parameters on FFAOR was then explored in details.After that,the reaction pathway was investigated and rationally proposed.The outstanding performance for FFAOR can be ascribed to the unique structure of 3D flower-like NiFe nanosheets and oxygen vacancies,resulting in large exposure of active sites,faster electron transfer and enhanced adsorption of reactants.Our findings highlight a facile and convenient mean with a promising green future,which is promising for processing of various biomass-derived platform chemicals into value-added products.
基金supported by a grant overseen by the French National Research Agency(ANR)as part of the“Investissements d’Avenir”Program(ANR-11-LABX-0002-01,Lab of Excellence ARBRE).
文摘Furfurylation is a well-known wood modification technology.This paper studied the effect of tannin addition on the wood furfurylation.Three kinds of dicarboxylic acids,adipic acid,succinic acid,and tartaric acid,as well as glyoxal as a comparing agent,were used to catalyse the polymerisation of furanic or tannin-furanic solutions during wood modification.Impregnation of furanic or tannin-furanic solution at a certain concentration into the wood followed with curing at 103℃for a specific duration was performed for the wood modification.Different properties of the modified woods like dimensional stability,resistance of treatment to leaching,mechanical properties,decay durability against white-rot(Coriolus versicolor,Pycnoporus sanguineus)and brown-rot(Coniophora puteana)as well as their chemical and anatomical characteristics were evaluated.Results revealed that the partial substitution of FA by the tannins improved the fixation of the chemicals impregnated in wood.Further,dimensional stability,leaching resistance,Brinell hardness,modulus of elasticity/modulus of rupture,and decay durability properties of the furfurylated wood were also improved in the presence of tannins.Scanning electron microscopy revealed the deposition of the polymer in the wood lumen cells and in the wood cell walls.
基金supported by the National Natural Science Foundation of China(2113301121203221+1 种基金21473224)the Natural Science Foundation of Gansu Province(1308RJZA281)~~
文摘Cu nanoparticles supported on a variety of oxide supports, including SiO2, TiO2, ZrO2, Al2O3, MgO and ZnO, were investigated for the hydrogenolysis of biomass‐derived furfuryl alcohol to1,2‐pentanediol and 1,5‐pentanediol. A Cu‐Al2O3 catalyst with 10 wt% Cu loading prepared by a co‐precipitation method exhibited the best performance in terms of producing pentanediols compared with the other materials. This catalyst generated an 85.8% conversion and a 70.3% combined selectivity for the target pentanediols at 413 K and 8 MPa H2 over an 8‐h reaction. The catalyst could also be recycled over repeated reaction trials without any significant decrease in productivity. Characterizations with X‐ray diffraction, NH3/CO2‐temperature programmed desorption, N2 adsorption,transmission electron microscopy and N2 O chemisorption demonstrated that intimate and effective interactions between Cu particles and the acidic Al2O3 support in this material greatly enhanced its activity and selectivity. The promotion of the hydrogenolysis reaction was found to be especially sensitive to the Cu particle size, and the catalyst with Cu particles 1.9 to 2.4 nm in size showed the highest turnover frequency during the synthesis of pentanediols.
文摘Selective hydrogenolysis of biomass‐derived furfuryl alcohol(FFA)to 1,5‐and 1,2‐pentanediol(PeD)was conducted over Cu‐LaCoO3 catalysts with different Cu loadings;the catalysts were derived from perovskite structures prepared by a one‐step citrate complexing method.The catalytic performances of the Cu‐LaCoO3 catalysts were found to depend on the Cu loading and pretreatment conditions.The catalyst with 10 wt%Cu loading exhibited the best catalytic performance after prereduction in 5%H2‐95%N2,achieving a high FFA conversion of 100%and selectivity of 55.5%for 1,5‐pentanediol(40.3%)and 1,2‐pentanediol(15.2%)at 413 K and 6 MPa H2.This catalyst could be reused four times without a loss of FFA conversion but it resulted in a slight decrease in pentanediol selectivity.Correlation between the structural changes in the catalysts at different states and the simultaneous variation in the catalytic performance revealed that cooperative catalysis between Cu0 and CoO promoted the hydrogenolysis of FFA to PeDs,especially to 1,5‐PeD,while Co0 promoted the hydrogenation of FFA to tetrahydrofurfuryl alcohol(THFA).Therefore,it is suggested that a synergetic effect between balanced Cu0 and CoO sites plays a critical role in achieving a high yield of PeDs with a high 1,5‐/1,2‐pentanediol selectivity ratio during FFA hydrogenolysis.
基金supported by the National Key R&D Program of China(2018YFB1501600)the National Natural Science Foundation of China(21572212,51821006,51961135104)+2 种基金the Major Science and Technology Projects of Anhui Province(18030701157)the Strategic Priority Research Program of Chinese Academy of Sciences(XDA21060101)the Local Innovative and Research Teams Project of Guangdong Pearl River Talents Program(2017BT01N092)~~
文摘The conversion of hemicellulose-derived xylose to furfuryl alcohol is a practical procedure for producing value-added chemicals from biomass.In this study,a bifunctional Cu/SBA-15-SO3 H catalyst was employed for the one-pot catalytic conversion of xylose to furfuryl alcohol with a yield of up to 62.6% at the optimized conditions of 140℃,4 MPa,and for 6 h in a biphasic water/n-butanol solvent.A high reaction temperature resulted in further hydrogenation to 2-methyl furan,while a high hydrogen pressure led to a side hydrogenation reaction to xylitol.The biphasic solvent allowed xylose solvation as well as furfuryl product extraction.The acidic-SO3 H sites and Cu sites co-existed,maintained a balance,and cooperatively catalyzed the cascade conversion.Excessive acidic sites and large pores could promote the xylose conversion,although a low furfuryl alcohol yield was obtained.This catalytic system could be potentially applied to the one-pot synthesis of furfuryl alcohol from hemicellulose-derived xylose.
文摘Silicoaluminophosphate-34(SAPO-34) molecular sieves have important applications in the petrochemical industry as a result of their shape selectivity and suitable acidity. In this work, nanoaggregate SAPO-34 with a large external surface area was obtained by dissolving pseudoboehmite and tetraethylorthosilicate in an aqueous solution of tetraethylammonium hydroxide and subsequently adding phosphoric acid. After hydrolysis in an alkaline solution, the aluminum and silicon precursors exist as Al(OH)4-and SiO2(OH)-, respectively;this is beneficial for rapid nucleation and the formation of nanoaggregates in the following crystallization process. Additionally, to study the effect of the external surface area and pore size on the catalytic performance of different SAPO-34 structures, the alcoholysis of furfuryl alcohol to ethyl levulinate(EL) was chosen as a model reaction. In a comparison with the traditional cube-like SAPO-34, nanoaggregate SAPO-34 generated a higher yield of 74.1% of EL, whereas that with cube-like SAPO-34 was only 19.9%. Moreover, the stability was remarkably enhanced for nanoaggregate SAPO-34. The greater external surface area and larger number of external surface acid sites are helpful in improving the catalytic performance and avoiding coke deposition.
基金supported by the National Centre for Research and Development(PolandNo PBS2/A5/30/2013)
文摘At present, furan resin is the largest selling no-bake system of moulding sands. The most commonly used furan no-bake binders(FNB) are condensation products of furfuryl alcohol(FA) urea, formaldehyde and phenol. They are generally cured by exposure to organic sulfonic acids. FNB provide excellent mold and core strength, cure rapidly and allow the sand to be reclaimed at fairly high yields, generally 75%-80%, especially in applications where due allowance is made for the need to keep total sulfur content below 0.1%. However, due to probable carcinogenic properties of furfuryl alcohol, the EU Directive limits the content of this substance(in a monomer form in resin) to 25%. The classification of furfuryl alcohol and the resulting furan resin products has changed from "harmful" to "toxic by inhalation". The aim of this study was to determine the effect of free furfuryl alcohol content in the resin on the emission of harmful substances from the BTEX(Benzene Toluene Ethylbenzene & Xylene) and PAHs(polycyclic aromatic hydrocarbon) group exposed to high temperature and how it affects the emissions allowance of reclaimed sand in the matrix. Three resins from a leading manufacturer were examined, which contain a free furfuryl alcohol content of 71%-72%, about 50% and < 25%, respectively. The hardener for each resin was 65% aqueous solution of paratoluenesulfonic acid. Tests were carried out in semi-industrial conditions where liquid cast-iron was poured into sample sand mold at 1,350 °C. The matrix of the studied sands was reclaimed in the amount of 0, 50%, 100%, respectively.With the increase of free furfuryl alcohol content, the volume of evolved gases decreased. For all resins the main component from the BTEX group dominating in the emitted gases was benzene; however toluene also appeared in the amount of a few percentages. In contrast, ethylbenzene and xylenes occurred only in the gases emitted from resin-bonded sands with the largest furfuryl alcohol content. The increase in the share of reclaimed sands resulted in very significant increase in the volume of gas generated and participation of benzene in these gases. In terms of emission of compounds from the PAHs group virtually for all resins, the total content of these substances was comparable(within the limits of error). The main components were: fluoranthene, pyrene and benzo(a) anthracene.
文摘Based on a special synthesis process of furan resin,the furfuryl alcohol(FA),the main component of typical no-bake furan resins is substituted by ethanol and xylitol mother liquor which is relatively low price and chemically active.Through orthogonal test,the optimal amount of xylitol liquor,ethanol and modifier has been determined.Finally,the test results on technical properties show that the performance can meet the production requirement well,which indicate a success in this substituting attempt.
文摘The Ni(Ⅱ) complex with ligand 2-N-(2-hydroxy-benzylidene) furanmethanoamine has been synthesized and characterized by elemental analysis, IR and single-crystal X-ray diffraction. It crystallizes in the monoclinic system, space group C2/c with a = 2.0280(4), b =0.57700(12), c = 1.7340(4) nm, β = 94.74(3)°, Z = 4, Dc = 1.508 g/cm^3, the final R = 0.0434 and wR = 0.1112 for 1843 observed reflections with 1 〉 2σ(I). X-ray analysis revealed that the Ni(Ⅱ) ion is coordinated by two nitrogen atoms of Schiff base and two oxygen atoms of salicylaldehyde in the equatorial plane, and the coordination geometry can be described as a square.
文摘An effect of phase compositions(rutile,Rut and anatase,Ant)of TiO_(2)supports on the selective hydrogenation of furfural to furfuryl alcohol was investigated.The 15%wt Ni/TiO_(2)catalysts were prepared by incipient impregnation method.The result showed that Ni supported on anatase-rutile mixed phase TiO_(2)(91%Rut and 9%Ant,A2)provided the highest furfuryl alcohol yield at 43.8%due to the relatively strong Ni-TiO_(2)interaction,its appropriate crystallite sizes,and high average pore sizes.Furthermore,the effect of cobalt as a promoter on Ni/TiO_(2)-A2 catalysts was studied.The result showed that the Ni-Co/TiO_(2)-A2 catalysts exhibited poorer catalyst performances compared to the monometallic Ni/TiO_(2),probably because addition of cobalt can lower the reduction temperatures of Ni/TiO_(2)and weaken the metal-support interaction.
基金financially supported from the Tianjin Research Program of Application Foundation and Advanced Technology (No. 17JCYBJC20200)the National Natural Science Foundation of China (No. 21878235)
文摘The catalytic transformation of furfuryl alcohol and hexose into value-added chemicals have been investigated with a series of polymer-based catalysts including poly(styrenesulfonic acid)(PSS),graphite oxide-doped poly(styrenesulfonic acid)(PSS-GO),and graphite-doped poly(-styrenesulfonic acid)(PSS-C).It is found that the selective conversion of furfuryl alcohol to methyl levulinate(MLE)was successfully performed with PSS as the catalyst,in which a 96.4%yield is attained in methanol solvent.Moreover,the efficient dehydration of D-fructose to produce 5-hydroxymethylfurfural(HMF)has also been achieved using PSS-GO as the catalyst,where a 76.5%yield of HMF was obtained in Nmethylpyrrodinone solvent.The effects of reaction temperature,time and solvent were investigated.Furthermore,the used catalysts have been respectively characterized by XRD,TG,FTIR,SEM and TEM techniques to reveal the physical properties and structures of these polymeric catalytic materials.
文摘The synthesis of a low cost no-bake furan resin with a high strength was researched in this paper. Through the analysis of main factors influencing the strength of furan resin, an orthogonal experiment was conducted to optimize synthesis of urea-formaldehyde furan resin with 3% nitrogen. The critical factors and their optimal levels were confirmed, and high strength property was obtained. Subsequently, some active substitute materials, including polyols A agent, methyl alcohol, mother liquid of xylitol, polyols B agent and ethanol, were used for partly substitution of furfural alcohol, the main material component of furan resin. A good combination of the substitute materials was determined to achieve a high strength, and the overal proportion of substitute materials to the resin is 20%. In this study, the substitution mechanism on furan resin was also characterized and analyzed by IR.
基金supported by the Youth Fund of the Natural Science Foundation of China(Grant No.31800482)Yunnan Provincial Natural Science Foundation(Grant No.2018FG001-095)+1 种基金Yunnan Provincial Reserve Talents for Middle&Young Academic and Technical Leaders(2019HB026)the Yunnan Provincial Youth Talent Support Project.
文摘Simple bio-based abrasive grinding wheel based on thermosetting resin matrix was developed starting with condensed tannin and furfuryl alcohol,which are mainly derived from forest and agricultural products like tree barks,wheat and crops.Fourier transform infrared spectra(FTIR)signified the acidic conditions are quiet efficient for the reaction of furfuryl alcohol,urea and glyoxal all together and the-CH_(2)-NH-and-CH_(2)-O-CH(OH)-groups are predominating in cross-linking of the tannin-furfuryl alcohol-urea-glyoxal(TFUG)resin.The strengthening contribution of the tannin was also confirmed by the preservation of its distinct crystallinity using X-ray diffraction(XRD).Differential scanning calorimetry(DSC)and thermogravimetric analysis(TGA)ensured that TFUG resin can be cured at low temperature and offer higher heat resistance compared with phenol-formaldehyde(PF)resin.The high hardness and excellent compressive strength revealed by the corresponding investigations such as Brinell hardness,compression resistance,and grinding tests suggested a strong abrasive ability using the new grinding wheel compared with lab-made grinding wheel based on PF resin.This could be ascribed to the absence of cracks and low content of formed holes as confirmed using scanning electron microscopy(SEM)and balanced reaction conditions that leads to network structure with regular local reinforcements and homogeneous crosslink density.
文摘A theoretical study of poly furfuryle alcohol (PFA), rhodamine B (Rh B) dye and their blends (PFA-Rh B) is carried out by using the density functional theory (DFT). Electronic states and opto-electronic properties are investigated. The electronic states indicate that the oligomers of FA are insulators and Rh B is a wide band gap semiconductor. Their blends have a narrow band gap of about 0.75 eV. The optoelectronic properties are studied using TDDFT, which indicates that the chain length of poly furfuryl alcohol is an effective parameter to control both energies and intensities of absorption in which longer chain causes absorption with high intensity within long wavelength. A single broad baned of electron excitations is more like 8-oligomer-RhB case, which centers at wavelengths about 599 nm and 625 nm. This band of absorption covers the whole visible region of spectrum.
文摘Vapor-phase transformations of furfural over SBA-15 silica supported Ni catalysts under H<sub>2</sub> in a continuous-flow reactor at atmospheric pressure and 170°C and 230°C were investigated. Two different samples having Ni loadings of 5 and 20 wt% (denoted here by SBA-5Ni and SBA-20Ni, respectively) were prepared by impregnation and characterized by atomic absorption spectroscopy, N<sub>2</sub> sorption analysis, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. Furan and furfuryl alcohol were two primary products resulting, respectively, from decarbonylation and hydrogenation of furfural. Under the conditions of the study, both reactions exhibited structure sensitivity evidenced by changes in product selectivities with variable Ni loadings. Compared with SBA-20Ni, the 5 wt% Ni catalyst showed better catalytic activity, reaching a furfural conversion of 100 mol% and a selectivity to furan of 98 mol%, after 5 h of time-on-stream at 230°C.
基金the National Key R&D Program of China(No.2022YFA1504601)Startup Program of the State Key Laboratory for Oxo Synthesis and Selective Oxidation of LICP,China(No.E0SX0184)+1 种基金the National Natural Science Foundation of China(Nos.22102193,21972151)the Key Research Program of Frontier Science of CAS(No.QYZDJSSW-SLH051).
文摘Selective activation of C-O bond is of fundamental importance in the precise conversion of oxygenates into value-added compounds in an atom-economic and sustainable manner, and meanwhile, the structurally well-defined dual-atoms catalysts (DACs) have been scarcely investigated in this field. In this study, a series of transition metal DACs anchored on nitrogen-doped graphene (TM2/NC, TM=Pt, Ir, Rh, Pd, Ru, Co, Ni and Cu) was constructed to make a comprehensive investigation of their selectivity in the hydrogenative transformation of furfuryl alcohol (FAL), an important biomass platform molecule, to 1,2-pentanediol (1,2-PeD) via selective cleavage of furanic C5-O bond, by density functional theory (DFT) calculations and microkinetic modeling. We found that Ir2/NC demonstrated a high selectivity for the cleavage of furanic C5-O bond to produce 1,2-PeD, while the production of THFAL or 1,5-pentanediol (1,5-PeD) on other TM2/NC catalysts are more favorable. Furthermore, we found that the selective C-O bond cleavage of FAL furan ring is affected by the orbital overlap between the d-orbitals of the anchored metal atoms and the p-orbitals of the adsorbed C atom in FAL, suggesting that the selectivity of the C-O bond cleavage is inextricably related with the electronic property of the anchored metals.
基金the National Natural Science Foundation of China (22108189, 22278286)Science Foundation for Distinguished Young Scholar of Shanxi Province(202303021223001)SINOPEC 122027
文摘Bimetallic CuCo catalysts with different Cu to Co ratios on N-doped porous carbon materials(N-C)were achieved using impregnation method and applied in the hydrogenation of furfural(FAL)to furfuryl alcohol(FOL).The high hydrogenation activity of FAL over Cu_(1)Co_(1)/N-C was originated from the synergistic interactions of Cu and Co species,where Co^(0)and Cu^(0)simultaneously adsorb and activate H_(2),and Cu^(+) served as Lewis acid sites to activate C]O.Meanwhile,electrons transfer from Cu to Co promoted the formation of Cu^(+).In situ Fourier transform infrared spectroscopy analysis indicated that Cu_(1)Co_(1)/N-C adsorbed FAL with a tilted η^(1)-(O)configuration.The superior Cu_(1)Co_(1)/N-C showed excellent adsorbed ability towards H_(2) and FAL,but weak adsorption for FOL.Therefore,Cu_(1)Co_(1)/N-C possessed 93.1%FAL conversion and 99.0% FOL selectivity after 5 h reaction,which also exhibited satisfactory reusability in FAL hydrogenation for five cycles.
基金supported by the National Natural Science Fund of China(Nos.21776234,21978246)。
文摘Catalytic transfer hydroge nation(CTH)of furfural(FF)to furfu ryl alcohol(FFA)has received great intere st in recent years.He rein,Cu-Cs bimetallic supported catalyst,CuCs(2)-MCM,was developed for the CTH of FF to FFA using formic as hydrogen donor.CuCs(2)-MCM achieved a 99.6%FFA yield at an optimized reaction conditions of 170℃,1 h.Cu species in CuCs(2)-MCM had dual functions in catalytically decomposing formic acid to generate hydrogen and hydrogenating FF to FFA.The doping of Cs made the size of Cu particles smaller and improved the dispersion of the Cu active sites.Impo rtantly,the Cs species played a favorable role in enhancing the hydrogenation activity as a promoter by adjusting the surface acidity of Cu species to an appropriate level.Correlation analysis showed that surface acidity is the primary factor to affect the catalytic activity of CuCs(2)-MCM.