Optimal preparation of Bose and Fermi atomic gas mixtures of ^(87)Rb and ^(40)K in a crossed optical dipole trap

We report on the optimal production of the Bose and Fermi mixtures with ^(87) Rb and ^(40)K in a crossed optical dipole trap(ODT).We measure the atomic number and lifetime of the mixtures in combination of the spin state |F=9/2,m_(F)=9/2> of^(40)K and |1,1>of ^(87) Rb in the ODT,which is larger and longer compared with the combination of the spin state |9/2,9/2> of^(40)K and 12,2) of ^(87)Rb in the ODT.We observe the atomic numbers of ^(87)Rb and ^(40)K shown in each stage of the sympathetic cooling process while gradually reducing the depth of the optical trap.By optimizing the relative loading time of atomic mixtures in the MOT,we obtain the large atomic number of ^(40)K(~6 ×10^(6)) or the mixtures of atoms with an equal number(~1.6 × 10^(6)) at the end of evaporative cooling in the ODT.We experimentally investigate the evaporative cooling in an enlarged volume of the ODT via adding a third laser beam to the crossed ODT and found that more atoms(8 × 10^(6)) and higher degeneracy(T/T_(F)=0.25) of Fermi gases are obtained.The ultracold atomic gas mixtures pave the way to explore phenomena such as few-body collisions and the Bose-Fermi Hubbard model,as well as for creating ground-state molecules of ^(87)Rb^(40)K.

Investigation of the performance of CF3I/c-C4F8/N2 and CF3I/c-C4F8/CO2 gas mixtures from electron transport parameters

CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas mixtures with c-C4F8 and buffer gases N2 and CO2 by considering dielectric strength from electron transport parameters based on the Boltzmann method and synergistic effect analysis,compared with SF6 gas mixtures.The results confirm that the critical electric field strength of CF3I/c-C4F8/70%CO2 is greater than that of 30%SF6/70%CO2 when the CF3I content is greater than 17%.Moreover,a higher content of c-C4F8 decreases the sensitivity of gas mixtures to an electric field,and this phenomenon is more obvious in CF3I/c-C4F8/CO2 gas mixtures.The synergistic effects for CF3I/c-C4F8/70%N2 were most obvious when the c-C4F8 content was approximately 20%,and for CF3I/c-C4F8/70%CO2 when the c-C4F8 content was approximately 10%.On the basis of this research,CF3I/c-C4F8/70%N2 shows better insulation performance when the c-C4F8 content is in the15%–20%range.For CF3I/c-C4F8/70%CO2,when the c-C4F8 content is in the 10%–15%range,the gas mixtures have excellent performance.Hence,these gas systems might be used as alternative gas mixtures to SF6 in high-voltage equipment.

The effective ionization coefficients and electron drift velocities in gas mixtures of CF_3I with N_2 and CO_2 obtained from Boltzmann equation analysis

The electron swarm parameters including the density-normalized effective ionization coefficients（α-η）/N and the electron drift velocities V e are calculated for a gas mixture of CF3I with N2 and CO2 by solving the Boltzmann equation in the condition of a steady-state Townsend（SST） experiment.The overall density-reduced electric field strength is from 100 Td to 1000 Td（1 Td = 10-17V·cm2）,while the CF3I content k in the gas mixture can be varied over the range from 0% to 100%.From the variation of（αη）/N with the CF3I mixture ratio k,the limiting field strength（E/N） lim for each CF3I concentration is derived.It is found that for the mixtures with 70% CF3I,the values of（E/N） lim are essentially the same as that for pure SF 6.Additionally,the global warming potential（GWP） and the liquefaction temperature of the gas mixtures are also taken into account to evaluate the possibility of application in the gas insulation of power equipment.

Calculation and characteristic analysis on synergistic effect of CF3I gas mixtures

CF3I is a potential SF6 alternative gas.In order to study the insulation properties and synergistic effects of CF3I/N2 and CF3I/CO2 gas mixtures,two-term approximate Boltzmann equations were used to obtain the ionization coefficient α,attachment coefficient η and the critical equivalent electrical field strength（E/N）（cr）.The results show that the（E/N）（cr）of CF3I gas at 300 K is 1.2 times that of SF6 gas,and CF3I/N2 and CF3I/CO2 gas mixtures both have synergistic effect occurred.The synergistic effect coefficient of CF3I/CO2 gas mixture was higher than that of CF3I/N2 gas mixture.But the（E/N）（cr）of CF3I/N2 is higher than that of CF3I/CO2 under the same conditions.When the content of CF3I exceeds 20%,the （E/N）（cr） of CF3I/N2 and CF3I/CO2 gas mixture increase linearly with the increasing of CF3I gas content.The breakdown voltage of CF3I/N2 gas mixture is also higher than that of CF3I/CO2 gas mixture in slightly non-uniform electrical field under power frequency voltage,but the synergistic effect coefficients of the two gas mixtures are basically the same.

Dispersion Relations in Binary Gas Mixtures From a Kinetic Theory

Sound propagation and the initial value problems in gas mixtures of two components are investigated. By using the eigen theory of linearized Boltzmann equations, a model equations is formed, with the use of the Fourier-Laplace transform for model equations derived, the dispersion relations for both components are obtained.

Calibrated explosive triangle for determining capacity of explosion of gas mixtures

Determination of the capacity for explosion of gas mixtures in a sealed area is very important for mining engineers.If this capacity is high,it would be very dangerous for rescue workers to proceed with their rescue operations.A number of methods have been developed to determine the capacity for explosion of gas mixtures in sealed areas.One of the more popular methods is the Coward explosive triangle,published by Coward.He presented a fast and easy way to determine the capacity for explosion of gas mixtures,which has proved to be a very useful tool for mining engineers and members of rescue teams.However,due to few drawbacks in this method;potential errors would be introduced when it is applied.In a brief introduction we first describe the Coward method and then,we propose and discuss new calibrated explosive triangles.We demonstrate the method in two case studies where we compare our results with those of the old model.The results indicate that the calibrated method have improved accuracy and reliability.Therefore,assessments can be made more accurately.

Predicting the Dielectric Strength of c-C_4F_8 and SF_6 Gas Mixtures by Monte Carlo Method

An improved Monte Carlo method was used to simulate the motion of electrons in c-C4F8 and SF6 gas mixtures for pulsed townsend discharge. The electron swarm parameters such as effective ionization coefficient, -↑α and drift velocity over the E/N range from 280～700 Td（1Td=10^-21 V·m^2） were calculated by employing a set of cross sections available in literature. From the variation cure of -↑α with SF6 partial pressure p, the limiting field （E/N）lim of gas mixture at different gas content was determined. It is found that the limiting field of c-C4F8 and SF6 gas mixture is higher than that of pure SF6 at any SF6 mixture ratio. Simulation results show excellent agreement with experiment data available in previous literature.

Transport properties of dilute ammonia-noble gas mixtures from new intermolecular potential energy functions

Previously we have determined the dilute mixture transport properties of slightly polar fluorocarbons using the inverted intermolecular potential energies(Ind. Eng. Chem. Res. 45(2006) 9211–9223). In the present paper, the corresponding states correlations for reduced viscosity collision integrals were employed to obtain effective unlike interaction potential models for dilute binary mixtures of highly polar molecule ammonia with noble gases.The inverted potentials were fitted to the Morse–Spline–van der Waals(MSV), model potential. The method of least-squares fitting was then applied to identify best consistence force parameters for each ammonia-noble gas mixture, taking advantage of experimental viscosities, diffusion coefficients and thermal conductivities.The proposed potential models were compared with those obtained from other sources, in order to assess the extent of their validity.The potentials were later employed to calculate transport properties of the studied mixtures. Then, results were compared with those reported in the literature, which led to the acceptable agreement.

Investigation of lubricant transfer and distribution at head/disk interface in air-helium gas mixtures

Lubricant transfer and distribution at the head/disk interface in air-helium gas mixtures is investigated using a developed model that combines an air-bearing model with a molecular dynamics model. The pressure distribution is calculated by the air-bearing model at the head/disk interface with respect to the helium content and the pressure obtained is then input to the molecular dynamics model to understand the lubricant transfer mechanism. Finally, the effects of pressure at the boundary condition and disk velocity on lubricant transfer are discussed in relation to the helium fraction within the air-helium gas mixtures. Results show there is a decrease in the pressure difference with an increase in the helium percentage, which leads to a decrease in the volume of the lubricant transferred. The results also suggest that the lubricant is not easily to transfer in gas mixtures with a high percentage of helium, even when both higher disk velocities and pressure boundary conditions are applied.

Monte Carlo Simulation of Electron Swarms Parameters in c-C_4F_8/CF_4 Gas Mixtures

The swarm parametes for c-C4F8/CF4 mixtures, including the density-normalized effective ion- ization coefficient, drift velocity and mean energy were calculated using Monte-Carlo method with the null collision technique. The overall density-reduced electric field strength could be varied between 150 and 500 Td, while the c-C4F8 content in gas mixtures is varied in the range of 0-100%. The value of the density-normalized effective ionization coefficient shows a strong dependence on the c-C4F8 content, becoming more electronegative as the content of c-C4F8 is increased. The drift velocity of c-C4F8/CF4 mixtures is more affected by CF4. The calculated limiting field strength for c-C4F8/CF4 mixtures is higher than that of SF6/CF4.

Employing Per-Component Time Step in DSMC Simulations of Disparate Mass and Cross-Section Gas Mixtures

A new approach to simulation of stationary flows by Direct Simulation Monte Carlo method is proposed.The idea is to specify an individual time step for each component of a gas mixture.The approach consists of modifications mainly to collision phase simulation and recommendations on choosing time step ratios.It allows lowering the demands on the computational resources for cases of disparate collision diameters of molecules and/or disparate molecular masses.These are cases important e.g.,in vacuum deposition technologies.Few tests of the new approach are made.Finally,the usage of new approach is demonstrated on a problem of silver nanocluster diffusion in argon carrier gas under conditions of silver deposition experiments.

Separation of CO_2/CH_4 and CH_4/N_2 mixtures using MOF-5 and Cu_3(BTC)_2

In this paper we used MOF-5 and Cu3（BTC）2 to separate CO2/CH4 and CI-I4/N2 mixtures under dynamic conditions. Both materials were synthesized and pelletized, thus allowing for a meaningful characterization in view of process scale-up. The materials were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. By performing breakthrough experiments, we found that Cu3（BTC）2 separated CO2/CH4 slightly better than MOF-5. Because the crystal structure of Cu3 （BTC）2 includes unsaturated accessible metal sites formed via dehydration, it predominantly interacted with CO2 molecules and more easily captured them. Conversely, MOF-5 with a suitable pore size separated CH4/N2 more efficiently in our breakthrough test.

Identification of the normal and abnormal glow discharge modes in a neon-xenon gas mixture at low pressure

In this paper, we focused on the identification of the normal and abnormal glow discharge modes in a neon-xenon gas mixture at low pressure. We considered four gas mixtures： 90%Ne-10%Xe, 80%Ne-20%Xe, 70%Ne-30%Xe and 50%Ne-50%Xe at 1.5 Torr. The range of the gap voltage is 150-500 V. A one-dimensional fluid model with multiple species was used in this work, and the metastable state of the atoms as well as the radiation effects were integrated into the model too. The input data changed for each percentage in the gas mixture, and was calculated by BOLSIG＋ software. The parameters of particle transport and their rate coefficients strictly depend on the mean electron energy. The results show that the neon ion density is negligible compared to the xenon ion density, mostly in the case of 50%Ne-50%Xe.

Breakdown Electric Field of Hot 30% CF_3I/CO_2 Mixtures at Temperature of 300–3500 K During Arc Extinction Process

We calculated the uniform dielectric breakdown field strength of residual 30% CF3I/CO2 gas mixtures during the arc extinction process over the temperature range 300-3500 K at 0.1 MPa. The limiting reduced field strengths are decided by a balance of electron generation and loss based on chemical reactions estimated by the electron energy distribution function （EEDF）, which employs the Boltzmann equation method with two-term expanding approximation in the steady-state Townsend （SST） condition. During the insulation recovery phase, the hot CF3I/CO2 gas mixtures have maximum dielectric strength at a temperature of about 1500 K. At room temperature 300 K, the electric strength after arc extinction （90.3 Td, 1 Td=10-21 V.m2） is only 38% of the original value before arc （234.9 Td）. The adverse insulation recovery ability of CF3I/CO2 gas mixtures in arc extinction hinders its application in electric circuit breakers and other switchgears as an arc quenching and insulating medium.

Insulation characteristics of triple mixtures of c-C_4F_8/N_2/CO_2 under lightning impulse voltage

This paper has researched the insulation characteristics of 10% c-C4F8/N2/CO2 mixtures under lightning impulse voltage by experiment. It is shown that the positive and negative lightning impulse breakdown voltages of 10%c-C4F8/N2/CO2 gas mixtures rise linearly as the electrode gap distance and gas pressure increase and under the same conditions, the positive lightning impulse breakdown voltage of the gas mixtures is always higher than the negative lightning impulse breakdown voltage. As the gas mixtures have a little higher liquefied temperature than SF6 and the comprehensive GWP is about 5% of SF6, and the positive and negative lightning impulse breakdown voltages can both reach 60% of SF6, 10%c-C4F8/N2/CO2 gas mixtures can be applied as insulation gas in electrical equipment such as C-GIS, GIT, GIL and so on.

Performance of Inner-core Supersonic Gas Separation Device with Droplet Enlargement Method

To improve the separation performance of a supersonic gas separation device for the treatment of gas mixture with a single heavy component, a novel structure with shorter settlement distance was constructed and a method of droplet enlargement was applied. A series of experiments were carried out in the improved separation device under various conditions, using air-ethanol vapor as the medium and micro water droplets as nucleation cen- ters. The effects of the inlet pressure, temperature and relative humidity, the swirling intensity, and mass flow rate of water on the separation performance were investigated. The separation was improved by increasing the inlet pressure and relative humidity. With the decrease of swirling intensity and mass flow rate of water, the separation efficiency increased first and then decreased. The inlet temperature had a slight effect on the separation. The results showed that the separation performance was effectively improved using the proposed structure and method, and the best separation in this study was obtained with the ethanol removal rate about 55% and dew point depression 27 K. The addition of water had little pollution to the air-ethanol vapor system since the water carry-over rate was within the range of -2 %-0 in most cases.

Numerical simulation for explosion wave propagation of combustible mixture gas

A two-dimensional multi-material code was indigenously developed to investigate the effects of duct boundary conditions and ignition positions on the propagation law of explosion wave for hydrogen and methane-based combustible mixture gas. In the code,Young's technique was employed to track the interface between the explosion products and air,and combustible function model was adopted to simulate ignition process. The code was employed to study explosion flow field inside and outside the duct and to obtain peak pressures in different boundary conditions and ignition positions. Numerical results suggest that during the propagation in a duct,for point initiation,the curvature of spherical wave front gradually decreases and evolves into plane wave. Due to the multiple reflections on the duct wall,multi-peak values appear on pressure-time curve,and peak pressure strongly relies on the duct boundary conditions and ignition position. When explosive wave reaches the exit of the duct,explosion products expand outward and forms shock wave in air. Multiple rarefaction waves also occur and propagate upstream along the duct to decrease the pressure in the duct. The results are in agreement with one-dimensional isentropic gas flow theory of the explosion products,and indicate that the ignition model and multi-material interface treatment method are feasible.

Protective behavior of an SO_2/CO_2 gas mixture for molten AZ91D alloy

The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.

The Effect of Pressure on the Dissociation of H_2/CH_4Gas Mixture during Diamond Films Growth via Chemical Vapor Deposition

Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used and the avalanche of electrons is taken into account in this simulation. The average energy distribution of electrons and the space distribution of effective species such as CH3, CH+3, CH+ and H at various gas pressures are given in this paper, and optimum experimental conditions are inferred from these results.

Distinguished discriminatory separation of CO2 from its methane-containing gas mixture via PEBAX mixed matrix membrane

Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based nanoparticles were homogenously integrated within the polymer matrix,facilitating penetration of CO_2 through the membrane while acting as barrier for methane gas.The membrane containing 4.6 wt% fumed silica(FS)(PEBAX/4.6 wt%FS)exhibits astonishing selectivity results where binary gas mixture of CO_2/CH_4 was used as feed gas.As detected by gas chromatography,in the permeate side,data showed a significant increase of CO_2 permeance,while CH_4 transport through the mixed matrix membrane was not detectable.Moreover,PEBAX/4.6 wt%FS greatly exceeds the Robeson limit.According to data reported on CO_2/CH_4 gas pair separation in the literature,the results achieved in this work are beyond those data reported in the literature,particularly when PEBAX/4.6 wt%FS membrane was utilized.