Microstructure and mechanical characteristics of AA6061-T6 joints produced by friction stir welding,friction stir vibration welding and tungsten inert gas welding:A comparative study

This study compared the microstructure and mechanical characteristics of AA6061-T6 joints produced using friction stir welding(FSW),friction stir vibration welding(FSVW),and tungsten inert gas welding(TIG).FSVW is a modified version of FSW wherein the joining specimens are vibrated normal to the welding line during FSW.The results indicated that the weld region grains for FSVW and FSW were equiaxed and were smaller than the grains for TIG.In addition,the weld region grains for FSVW were finer compared with those for FSW.Results also showed that the strength,hardness,and toughness values of the joints produced by FSVW were higher than those of the other joints produced by FSW and TIG.The vibration during FSW enhanced dynamic recrystallization,which led to the development of finer grains.The weld efficiency of FSVW was approximately 81%,whereas those of FSW and TIG were approximately 74%and 67%,respectively.

Feature Extraction and Dimensionality Reduction of Arc Sound under Typical Penetration Status in Metal Inert Gas Welding

Arc sound is well known as the potential and available resource for monitoring and controlling of the weld penetration status,which is very important to the welding process quality control,so any attentions have been paid to the relationships between the arc sound and welding parameters.Some non-linear mapping models correlating the arc sound to welding parameters have been established with the help of neural networks.However,the research of utilizing arc sound to monitor and diagnose welding process is still in its infancy.A self-made real-time sensing system is applied to make a study of arc sound under typical penetration status,including partial penetration,unstable penetration,full penetration and excessive penetration,in metal inert-gas（MIG） flat tailored welding with spray transfer.Arc sound is pretreated by using wavelet de-noising and short-time windowing technologies,and its characteristics,characterizing weld penetration status,of time-domain,frequency-domain,cepstrum-domain and geometric-domain are extracted.Subsequently,high-dimensional eigenvector is constructed and feature-level parameters are successfully fused utilizing the concept of primary principal component analysis（PCA）.Ultimately,60-demensional eigenvector is replaced by the synthesis of 8-demensional vector,which achieves compression for feature space and provides technical supports for pattern classification of typical penetration status with the help of arc sound in MIG welding in the future.

A novel single wire indirect arc metal inert gas welding process operated in streaming mode

Dilution of a pad weld must be limited to a certain critical level to improve its wear and/or corrosion properties.To do that,a novel single wire indirect arc metal inert gas welding process operated in streaming mode was realized.A metal inert gas welding torch,arranged perpendicular to a substrate in vertical position,is fixed with an auxiliary tungsten electrode horizontally.The arc is ignited between a wire through the torch and the auxiliary electrode.The substrate is not electrically connected.The welding current is set in the range of streaming mode.304 stainless steel was pad welded on Q235 substrates in vertical position by this process.Microstructures were analyzed with optical microscope.Dilution ratios were measured with stereo light microscope and calculated.The results show that,after eliminating interference of the massive torch setup,the dilution ratio of the pad weld with optimized parameters is 5.07%,much less than that with a metal inert gas welding process,which is 26.46%.The pad weld is bonded to the substrate without defects.Microstructures of the pad weld consist of columnar austenite and ferrite between the columns.The dilution ratio increases with increasing welding current or welding velocity,and decreases with increasing distance to the substrate.

Influence of arc pressure on the forming of molten pool in tungsten inert gas arc butt welding with micro gap for tantalum sheet

Arc pressure is the key influencing factor to forming of molten pool. Countering the characteristic of tungsten inert gas arc welding with micro gap for tantalum sheet, according to the fundament of arc physics, a distribution model of arc pressure and forming mechanism of molten pool with micro butt gap are proposed, and the influences of arc pressure on forming of molten pool are discussed. Experimental researches for the dynamic formation process of weld molten pool by using high-speed vidicon camera show that when butt gap is appropriate, that is from 0. 1 to 0. 15 mm, molten metals formed on two workpiece uplift and grow up first, then are fused and form uniform molten pool finally.

Microstructure and mechanical properties of friction pull plug welding for2219-T87 aluminum alloy with tungsten inert gas weld

The friction pull plug welding(FPPW)of the 2219-T87 tungsten inert gas(TIG)welded joint was investigated,and the microstructures,precipitate evolution,mechanical properties,and fracture morphologies of this joint were analyzed and discussed.In this study,defectfree joints were obtained using a rotational speed of 7000 r/min,an axial feeding displacement of 12 mm,and an axial force of 20-22 kN.The results indicated that within these welding parameters,metallurgical bonding between the plug and plate is achieved by the formation of recrystallized grains.The microstructural features of the FPPW joint can be divided into different regions,including the heat-affected zone(HAZ),thermomechanically affected zone(TMAZ),recrystallization zone(RZ),heat-affected zone in the TIG weld(TIG-HAZ),and the thermomechanically affected zone in the TIG weld(TIG-TMAZ).In the TIG-TMAZ,the grains were highly deformed and elongated due to the shear and the extrusion that produces the plug during the FPPW process.The main reason for the softening in the TMAZ is determined to be the dissolution ofθ’and coarsening ofθprecipitate particles.In a tensile test,the FPPW joint welded with an axial force of 22 kN showed the highest ultimate tensile strength of 237 MPa.The locations of cracks and factures in the TIG-TMAZ were identified.The fracture morphology of the tensile sample showed good plasticity and toughness of the joints.

Gas tungsten arc welding of CP-copper to 304 stainless steel using different filler materials

The dissimilar joining of CP-copper to 304 stainless steel was performed by gas tungsten arc welding process using different filler materials. The results indicated the formation of defect free joint by using copper filler material. But, the presence of some defects like solidification crack and lack of fusion caused decreasing tensile strength of other joints. In the optimum conditions, the tensile strength of the joint was 96% of the weaker material. Also, this joint was bent till to 180° without any macroscopic defects like separation, tearing or fracture. It was concluded that copper is a new and good candidate for gas tungsten arc welding of copper to 304 stainless steel.

Optimizing the Pulsed Current Gas Tungsten Arc Welding Parameters

The selection of process parameter in the gas tungsten arc （GTA） welding of titanium alloy was presented for obtaining optimum grain size and hardness. Titanium alloy （Ti-6Al-4V） is one of the most important non-ferrous metals which offers great potential application in aerospace, biomedical and chemical industries, because of its low density （4.5 g/cm^3）, excellent corrosion resistance, high strength, attractive fracture behaviour and high melting point （1678℃）. The preferred welding process for titanium alloy is frequent GTA welding due to its comparatively easier applicability and better economy. In the case of single pass （GTA） welding of thinner section of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current process. Many considerations come into the picture and one needs to carefully balance various pulse current parameters to reach an optimum combination. Four factors, five level, central composite, rotatable design matrix were used to optimize the required number of experimental conditions. Mathematical models were developed to predict the fusion zone grain size using analysis of variance （ANOVA） and regression analysis. The developed models were optimized using the traditional Hooke and Jeeve＇s algorithm. Experimental results were provided to illustrate the proposed approach.

Optimization of pulsed current gas tungsten arc welding process parameters to attain maximum tensile strength in AZ31B magnesium alloy

An empirical relationship to predict tensile strength of pulsed current gas tungsten arc welded AZ31B magnesium alloy was developed. Incorporating process parameters such as peak current, base current, pulse frequency and pulse on time were studied. The experiments were conducted based on a four-factor, five-level, central composite design matrix. The developed empirical relationship can be effectively used to predict the tensile strength of pulsed current gas tungsten arc welded AZ31B magnesium alloy joints at 95% confidence level. The results indicate that pulse frequency has the greatest influence on tensile strength, followed by peak current, pulse on time and base current.

In situ synthesis and hardness of TiC/Ti_5Si_3 composites on Ti-5Al-2.5Sn substrates by gas tungsten arc welding

TiC/TisSi3 composites were fabricated on Ti-5A1-2.5Sn substrates by gas tungsten arc welding （GTAW）. Identification of the phases was performed using X-ray diffraction （XRD）. The microstructures were analyzed using scanning electron microscopy （SEM） combined with energy-dispersive X-ray spectrometry （EDS） and optical microscopy （OM）. The Vickers hardness was measured with a micro-hardness tester. The TiC/TisSi3 composites were obtained in a double-layer track, and the Vickers hardness of the track increased by two to three times compared with the Ti-5A1-2.5Sn substrate.

Assessment of gas tungsten arc welding thermal cycles on Inconel 718 alloy

Heat moving source models along with transient heat analysis by finite element method were used to determine weld thermal cycles and isothermal sections obtained from the application of a gas tungsten arc welding beads on Inconel 718 plates. Analytical (Rosenthal’s thick plate model) and finite element results show an acceptable approximation with the experimental weld thermal cycles. The isothermal sections determined by numerical simulation show a better approximation with the experimental welding profile for double-ellipse model heat distribution than Gauss model. To analyze the microstructural transformation produced by different cooling rates in the fusion and heat affected zones, Vickers microhardness measurements (profile and mapping representation) were conducted. A hardness decrement for the heat affected zone (~200 HV0.2) and fusion zone (~240 HV0.2) in comparison with base material (~350 HV0.2) was observed. This behavior has been attributed to the heterogeneous solubilization process of the γ″ phase (nickel matrix), which, according to the continuous-cooling-transformation curve, produced the Laves phase,δ and MC transition phases, generating a loss in hardness close to the fusion zone.

Effect of process parameters of pulsed current tungsten inert gas welding on weld pool geometry of titanium welds

The effects of pulsing current parameters on weld pool geometry namely front height, back height, front width and back width of pulse current gas tungsten arc welded （GTAW） titanium alloy was analysed. Four factors, five levels, central composite design were used to develop empirical relationships, incorporating pulsed current parameters and weld pool geometry.

Study on chaos in short circuit gas metal arc welding process

Based on the chaos theory, an idea is put forward to analyze the short circuit Gas Metal Arc Welding （ GMAW-S） process. The theory of phase space reconstruction and related algorithms such as mutual information and so on, are applied to analyze the chaos of the GMAW-S process. The largest Lyapunov exponents of some current time series are calculated, and the results indicate that chaos exists in the GMAW-S process. The research of the chaos in the GMAW-S process can be help to get new knowledge of the process.

A NEURAL NETWORK FOR WELD PENETRATION CONTROL IN GAS TUNGSTEN ARC WELDING

Realizing of weld penetration control in gas tungsten arc welding requires establishment of a model describing the relationship between the front-side geometrical parameters of weld pool and the back-side weld width with sufficient accuracy. A neural network model is developed to attain this aim. Welding experiments are conducted to obtain the training data set （including 973 groups of geometrical parameters of the weld pool and back-side weld width） and the verifying data set （108 groups）. Two data sets are used for training and verifying the neural network, respectively. The testing results show that the model has sufficient accuracy and can meet the requirements of weld penetration control.

Computer-based sensing and visualizing of metal transfer mode in gas metal arc welding

Using Xenon lamp lights to overcome the strong interference from the welding arc, a computer-based system is developed to sense and visualize the metal transfer in GMAW. This system combines through-the-arc sensing of the welding current and arc voltage with high speed imaging of the metal transfer. It can simultaneously display the metal transfer processes and waveforms of electrical welding parameters in real-time The metal transfer videos and waveforms of electrical welding parameters can be recorded. Metal transfers under various welding conditions have been investigated with the system developed.

Digital control of pulsed gas metal arc welding inverter using TMS320LF2407A

A digital control of pulsed gas metal arc welding inverter was proposed. A control system consisting of analogue parts was replaced with a new digital control implemented in a TMS320LF2407A DSP chip. The design and constructional features of the whole digital control were presented. The resources of the DSP chip were efficiently utilized and the circuits are very concise, which can enhance the stability and reliability of welding inverter. Experimental results demonstrate that the developed digital control has the ability to accomplish the excellent pulsed gas metal arc welding process and the merits of the developed digital control are stable welding process, little spatter and perfect weld appearance.

Determining chaotic invariant properties of short-circuiting gas metal arc welding from an observed time series

The experimental time series of welding current produced by carbon dioxide gas metal arc welding with shortcircuiting transfer were recorded and subsequently evaluated. Based on phase space reconstruction, the correlation dimeusions and Kolmogorov entropies of the corresponding system have been numerically calculated using the Grassberger-Procaccia algorithm at different time delays. It was found out that the time delay has little effect on the estimation of correlation dimension; conversely, it plays a key role in producing precise results on the estimation of Kolmogorov entropy.

Experimental study on gas metal arc welding and laser hybrid welding of WYS700 steel

Gas metal arc welding, laser welding, and laser-metal active gas welding(MAG) hybrid welding methods were applied to WYS700 steel.Different welding procedures were performed and different welding technologies were compared.Macro metallographs of the welded joints were obtained, and the mechanical properties(such as tensile strength, bending property, and hardness) of the joints formed using the different welding technologies were determined.The results revealed that the joint of the WYS700 steel could be formed well through gas metal arc welding, laser welding, and laser-MAG hybrid welding.Furthermore, the softening of the welding heat affected zone can be effectively reduced to obtain good strength and plasticity by using a suitable welding procedure.Laser-MAG hybrid welding allows the realization of high efficiency and deep penetration for the welding of thick plates with specifications above 3 mm.

Analysis of Arc Physical Property of Pulsed Tungsten Inert Gas Welding Based on Fowler-Milne Method

Pulsed tungsten inert gas （TIG） welding is widely used in industry due to its superior properties, so the measurement of arc telnperature is important to analyse welding process. Arc image of spectral line in 794.8 nm is captured by high speed camera; both the Abel inversion and the Fowler-Milne method are used to calculate the temperature distribution of the pulsed TIG welding. Characteristic of transient variation in arc intensity and temperature is analyzed. When the change of current happens, intensity and temperature of arc jump as well, it costs several millisoconds. The flirther the axial position from the tungsten is, the greater the intensity jumps, and the smaller the temperature changes.

Study on gas metal arc welding of two types of TMCP steels

Gas metal arc welding experiments were conducted on two types of steels with 0.41% carbon equivalent(Ceq) and 0.31% Cequsing WER70T wire and 20% CO_(2)and 80% Ar as shielding gas.The two types of steels show satisfactory weldability.The transition temperatures of 50% upper shelf energy(Tk0.5) for Charpy-V impact test of both the welded joints are below-40 ℃.However, the toughness of the fusion line zone and heat-affected zone(HAZ) of the two steel joints exhibits differences, with the toughness of 0.41% Ceqsteel being better than that of 0.31% Ceqsteel.The Tk0.5of the fusion line zone and the HAZ of 0.41% Ceqsteel is below-60℃,whereas that of 0.31% Ceqsteel is above-40℃.The welded joint of 0.41% Ceqsteel has low hardness fluctuation, while that of 0.31% Ceqsteel exhibits a narrow, softened zone, which has no obvious influence on the tested tensile strength.The coarse grain heat-affected zone(CGHAZ)microstructure of 0.41% Ceqsteel is bainite, while that of 0.31% Ceqsteel is bainite with ferrite and minor pearlite.

Gas metal arc welding of duplex stainless clad steel plates

The 2205 duplex stainless ＋ DH36 clad steel plate was welded by gas metal arc welding（GMAW）, and the welding performance of the clad steel plate was investigated. The results show that the adaptability of the welding procedure for the base metal of carbon steel, the transition layer, and the cladding material is excellent. The test results indicate that the phase proportion and component dilution of the GMAW-welded joints of clad steel plate can be effectively controlled to yield joints with good mechanical properties and corrosion resistance.