Effect of CO_(2)flooding in an oil reservoir with strong bottom-water drive in the Tahe Oilfield,Tarim Basin,Northwest China

The dissolution and diffusion of CO_(2)in oil and water and its displacement mechanism were investigated by laboratory experiment and numerical simulation for Block 9 in the Tahe oilfield,a sandstone oil reservoir with strong bottom-water drive in Tarim Basin,Northwest China.Such parameters were analyzed as solubility ratio of CO_(2)in oil,gas and water,interfacial tension,in-situ oil viscosity distribution,remaining oil saturation distribution,and oil compositions.The results show that CO_(2)flooding could control water coning and increase oil production.In the early stage of the injection process,CO_(2)expanded vertically due to gravity differentiation,and extended laterally under the action of strong bottom water in the intermediate and late stages.The CO_(2)got enriched and extended at the oil-water interface,forming a high interfacial tension zone,which inhibited the coning of bottom water to some extent.A miscible region with low interfacial tension formed at the gas injection front,which reduced the in-situ oil viscosity by about 50%.The numerical simulation results show that enhanced oil recovery(EOR)is estimated at 5.72%and the oil exchange ratio of CO_(2)is 0.17 t/t.

Study on Optimal Water ControlMethods for Horizontal Wells in Bottom Water Clastic Rock Reservoirs

The segmented water control technology for bottom water reservoirs can effectively delay the entry of bottom water and adjust the production profile.To clarify the impact of different methods on horizontal well production with different reservoir conditions and to provide theoretical support for the scientific selection of methods for bottom water reservoirs,a numerical simulation method is presented in this study,which is able to deal with wellbore reservoir coupling under screen tube,perforation,and ICD(Inflow Control Device)completion.Assuming the geological characteristics of the bottom-water conglomerate reservoir in the Triassic Formation of the Tahe Block 9 as a test case,the three aforementioned completion methods are tested to predict the transient production characteristics.The impact of completion parameters,reservoir permeability,bottom-water energy,and individual well control on the time to encounter water in horizontal wells(during a water-free production period)is discussed.A boundary chart for the selection of completion methods is introduced accordingly.The results show that the optimized ICD completion development effect for heterogeneous reservoirs is the best,followed by optimized perforation completion.Permeability is the main factor affecting the performances of completion methods,while bottom water energy and single well controlled reserves have a scarce impact.The average permeability of the reservoir is less than 500 mD,and ICD has the best water control effect.If the permeability is greater than 500 mD,the water control effect of perforation completion becomes a better option.

Evaluation of reservoir environment by chemical properties of reservoir water‒A case study of Chang 6 reservoir in Ansai oilfield,Ordos Basin,China

The Ordos Basin is the largest continental multi-energy mineral basin in China,which is rich in coal,oil and gas,and uranium resources.The exploitation of mineral resources is closely related to reservoir water.The chemical properties of reservoir water are very important for reservoir evaluation and are significant indicators of the sealing of reservoir oil and gas resources.Therefore,the caprock of the Chang 6 reservoir in the Yanchang Formation was evaluated.The authors tested and analyzed the chemical characteristics of water samples selected from 30 wells in the Chang 6 reservoir of Ansai Oilfield in the Ordos Basin.The results show that the Chang 6 reservoir water in Ansai Oilfield is dominated by calcium-chloride water type with a sodium chloride coefficient of generally less than 0.5.The chloride magnesium coefficients are between 33.7 and 925.5,most of which are greater than 200.The desulfurization coefficients range from 0.21 to 13.4,with an average of 2.227.The carbonate balance coefficients are mainly concentrated below 0.01,with an average of 0.008.The calcium and magnesium coefficients are between 0.08 and 0.003,with an average of 0.01.Combined with the characteristics of the four-corner layout of the reservoir water,the above results show that the graphics are basically consistent.The study indicates that the Chang 6 reservoir in Ansai Oilfield in the Ordos Basin is a favorable block for oil and gas storage with good sealing properties,great preservation conditions of oil and gas,and high pore connectivity.

Temporal variations in geochemistry of hydraulic fracturing fluid and flowback water in a tight oil reservoir

Hydraulic fracturing facilitates the development and exploitation of unconventional reservoirs.In this study,the injected hydraulic fracturing fluid(HFF)and flowback and produced water(FPW)in tight oil reservoirs of the Lucaogou Formation in the Junggar Basin are temporally sampled from day 1 to day 64.Freshwater is used for fracturing,and HFF is obtained.The chemical and isotopic parameters(including the water type,total salinity,total dissolved solids(TDS),pH,concentrations of Na^(+),Cl^(-),Ba^(+),K^(+),Fe^(2+)+Fe^(3+),and CO_(3)^(2-),dD,and δ^(18)O)are experimentally obtained,and their variations with time are systematically analyzed based on the flowback water.The results show that the water type,Na/Cl ratio,total salinity,and TDS of the FPW change periodically primarily due to the HFF mixing with formation water,thus causing δD and δ^(18)O to deviate from the meteoric water line of Xinjiang.Because of watererock interaction(WRI),the concentrations of Fe^(2+)+Fe^(3+)and CO_(3)^(2-)of the FPW increase over time,with the solution pH becoming more alkaline.Furthermore,based on the significant changes observed in the geochemistry of the FPW,three separate time intervals of flowback time are identified:Stage Ⅰ(<10 days),where the FPW is dominated by the HFF and the changes in ions and isotopes are mainly caused by the WRI;Stage Ⅱ(10-37 days),where the FPW is dominated by the addition of formation water to the HFF and the WRI is weakened;and finally,Stage Ⅲ(>37 days),where the FPW is dominated by the chemistry of the formation water.The methodology implemented in this study can provide critical support for the source identification of formation water.

Method of moderate water injection and its application in ultra-low permeability oil reservoirs of Yanchang Oilfield, NW China

To explore the method of improving development effect and solving the problem of water breakthrough and water out for ultralow permeability fractured reservoirs, an indoor evaluation method of dynamic imbibition for fracture-matrix system was established taking the Chang 8 reservoir in southern Yanchang Oilfield as a research target. Key factors for the imbibition effect were obtained, an imbibition's rate expression was obtained, a model considering the double effects of imbibition-displacement was built and optimal injection and production parameters for the research area were obtained as well. The results show that an optimum displacement rate that maximizes the oil displacement efficiency exists in the water displacing oil process, and the optimal displacing rate becomes smaller as the permeability decreases. The imbibition displacement efficiency increases as the reservoir quality index and water wettability index of rock become bigger. But the larger the initial water saturation or oil-water viscosity ratio is, the smaller the imbibition displacement efficiency is. The optimal injection-production ratio for the Chang 8 reservoir of southern Yanchang Oilfield is 0.95, and the predicted recovery is 17.2% when the water cut is 95%, it is 2.9% higher than the recovery of conventional injection-production ratio 1.2. By using the moderate water injection technique based on the double effects of imbibition-displacement mechanism, the water injection development effect for the ultra-low permeability fractured reservoirs can be improved significantly.

A Review of Formation Mechanism Study on Reservoirs with Tilted Oil-water Contacts

The distribution characteristics of the oil-water contact are the basis for the reservoir exploration and development and reserves evaluation. The reservoir with a tilted oil-water contact has a unique formation mechanism, and the understanding of its distribution and formation mechanism will directly affect the evaluations for the reservoir type, well deployment, selection of well pattern and type, determination of test section, and reserves evaluation. Based on the analysis of reservoir characteristics, petrophysical properties and geological structure in 40 reservoirs worldwide with tilted oil-water contacts, the progress of the research on the formation mechanisms of titled oil-water contacts is summarized in terms of the hydrodynamic conditions, reservoir heterogeneity, neotectonic movement and oil-gas exploitation. According to the formation mechanism of tilted oil-water contacts and the needs of exploration research, different aspects of research methods are summarized and classified, such as the calculation of equipotential surfaces for oil and water in the formation, analysis of formation pressure and analysis of reservoir physical properties and so on. Based upon statistical analysis, it is suggested that the degree of the inclination of the oil-water contact be divided based on the dip of oil-water contact（DipTOWC）. The tilted oil-water contact is divided into three categories： large dip（DipTOWC≥55 m/km）, medium dip（4 m/km≤DipTOWC55 m/km）, and small dip（DipTOWC4 m/km）. The classification and evaluation method can be combined with structure amplitude and reservoir property. The formation mechanism of domestic and international reservoirs with tilted oil-water contacts are summarized in this paper, which have important significance in guiding the exploration and development of the oilfield with tilted oil-water contacts, reserves evaluation, and well deployment.

Mechanisms of remaining oil formation by water flooding and enhanced oil recovery by reversing water injection in fractured-vuggy reservoirs

To get a deeper understanding on the formation mechanisms and distribution laws of remaining oil during water flooding, and enhanced oil recovery(EOR) mechanisms by reversing water injection after water flooding, 3D visualization models of fractured-vuggy reservoir were constructed based on the elements and configuration of fractures and vugs, and typical fracture-vug structures by using advanced CT scanning and 3D printing technologies. Then, water flooding and reversing water injection experiments were conducted. The formation mechanisms of remaining oil during water flooding include inadequate injection-production well control, gravity difference between oil and water, interference between different flow channels, isolation by low connectivity channel, weak hydrodynamic force at the far end. Under the above effects, 7 kinds of remaining oil may come about, imperfect well-control oil, blind side oil, attic oil at the reservoir top, by-pass residual oil under gravity, by-pass residual oil in secondary channel, isolated oil in low connectivity channel, and remaining oil at far and weakly connected end. Some remaining oil can be recovered by reversing water injection after water flooding, but its EOR is related to the remaining oil type, fracture-cavity structure and reversing injection-production structure. Five of the above seven kinds of remaining oil can be produced by six EOR mechanisms of reversing water injection: gravity displacement, opening new flow channel, rising the outflow point, hydrodynamic force enhancement, vertically equilibrium displacement, and synergistic effect of hydrodynamic force and gravity.

Remaining Oil Distribution Law and Potential Tapping Strategy of Horizontal Well Pattern in Narrow Oil Rim Reservoir with Gas Cap and Edge Water

For thin oil rim reservoir with gas cap and edge water, it is helpful to improve the development effect to find out the distribution law of remaining oil in this kind of reservoirs. For this reason, taking the narrow oil rim reservoir with gas cap and edge water of Oilfield A in Bohai Sea as a case, the main controlling factors, including reservoir structure, fault, gas cap energy, edge water energy and well pattern, affecting the distribution of residual oil in this kind of reservoir were analyzed by using the data of core, logging, paleogeomorphology and production. Then, the distribution law of remaining oil was summarized. Generally, the remaining oil distribution is mainly potato-shaped or strip-shaped in plane. Vertically, it depends on the energy of gas cap and edge water. For the reservoir with big gas gap and weak edge water, the remaining oil mainly lies in the bottom of oil column. And for the reservoir with small gas gap and strong edge water, the remaining oil mainly locates at the top of oil column. Aiming at different distribution modes of remaining oil, the corresponding potential tapping strategies of horizontal wells are put forward: in the late stage of development, for the reservoir with big gas gap and weak edge water, the remaining oil concentrates at the bottom of the oil column, and the position of horizontal well should be placed at the lower 1/3 to the lower 1/5 of the oil column;for the reservoir with small gas cap and strong edge water, the remaining oil locates at the top of the oil column, and the position of horizontal well should be put at the upper 1/5 to the upper 1/3 of the oil column height, vertically. Based on the study on remaining oil of Oilfield A, a potential tapping strategy of well pattern thickening and vertical position optimization of horizontal well was proposed. This strategy guided the efficient implementation of the comprehensive adjustment plan of the oilfield. Moreover, 18 infill development wells were implemented in Oilfield A, and the average production of the infill wells is 2.1 times that of the surrounding old wells. It is estimated that the ultimate recovery factor of the oilfield will reach 33.9%, which is 2.3% higher than that before infilling wells. This study can be used for reference in the development of similar reservoirs.

The control effect of low-amplitude structure on oil-gaswater enrichment and development performance of ultra-low permeability reservoirs

Based on drilling, logging, test production and dynamic monitoring data, the control effects of low-amplitude structure on hydrocarbon accumulation and development performance of ultra-low permeability reservoirs were discussed by using the methods of dense well pattern, multi-factor geological modeling, macro and micro analysis and static and dynamic analysis. The results show that the low-amplitude structure always had a significant control and influence on the distribution and accumulation of original hydrocarbon and water and the evolution trend of water flooding performance in ultra-low permeability reservoirs, and it was not only the direction of oil and gas migration, but also a favorable place for relative accumulation of oil and gas. The controlling effect of low-amplitude structure on ultra-low permeability reservoir mainly depended on its tectonic amplitude and scale;the larger the tectonic amplitude and scale, and the higher the tectonic position of the low amplitude structure, the better the reservoir characteristic parameters, oil and gas enrichment degree and development effect, and the larger the spatial scope it controlled and influenced;water cut and oil well output always fluctuated orderly with the height of the low-amplitude structure;the dynamic response of waterflooding was closely related to the relative structural position of the injection and production wells;the injected water always advanced to the low-lying area of the structure first and then moved up to the high-lying area of the structure gradually;with the continuous expansion of the flooded area, part of the oil and gas in the low-lying part of the structure was forced to be distributed to the high part of the structure, resulting in a new oil and gas enrichment, so that the dynamic reserves of oil wells in the high part increased, and the production capacity remained stable.

Using cyclic alternating water injection to enhance oil recovery for carbonate reservoirs developed by linear horizontal well pattern

In view of high water cut and low oil recovery caused by the unidirectional flow in linear pattern of horizontal wells for the carbonate reservoirs in the Middle East,this paper provides a novel approach to improve oil recovery by converting linear water injection to cyclic alternating water injection patterns including cyclic alternating water injection with apparent inverted seven-spot pattern or apparent five-spot pattern and cyclic differential alternating water injection.The main advantage of using this strategy is that the swept efficiency is improved by changing injection-production streamlines and displacement directions,which means displacement from two different direction for the same region during a complete cycle.This technology is effective in increasing the swept efficiency and tapping the remaining oil,thus resulting in higher oil recovery.Field application with three new patterns in a carbonate reservoir in the Middle East is successful.By optimizing injection and production parameters based on the cyclic alternating well pattern,the test well group had a maximum increase of daily oil production per well of 23.84 m^(3) and maximum water cut drop of 18%.By further optimizing the distance(keep a long distance)between the heels of injection and production wells,the waterflooding performance could be better with water cut decreasing and oil production increasing.

Geochemical characteristics of reservoir after water and polymer flooding in Xingshugang oilfield of Daqing

Collecting 44 oil-sand specimens of Pu-I Member in two inspection wells before and after polymer flooding in the thirteenth district of Xingshugang oilfield,with experimental analysis,the author obtained the data about oil viscosity,flow,oil saturation and oil displacement efficiency.The result shows that viscous oil predominates in the main remaining oil in Xingshugang oilfield after water flooding with a certain amount of low viscosity oil,high viscosity oil and heavy oil;after polymer flooding,the viscous oil is main ingredient.Compared with water flooding,the low mobility and poor oil can be spread by polymer flooding,expanding the affected area and improving sweep efficiency and oil recovery.The geochemical affecting factors of water flooding and oil displacement efficiency refer to reservoir flow,permeability and the viscosity of residual oil.In the reservoir with permeability from low to high,the polymer flooding efficiency is better than water flooding.It provides the basis for improving the water and polymer flooding efficiency of the Xingshugang oilfield.

The impact of connate water saturation and salinity on oil recovery and CO2 storage capacity during carbonated water injection in carbonate rock

Carbonated water injection(CWI)is known as an efficient technique for both CO2 storage and enhanced oil recovery(EOR).During CWI process,CO2 moves from the water phase into the oil phase and results in oil swelling.This mechanism is considered as a reason for EOR.Viscous fingering leading to early breakthrough and leaving a large proportion of reservoir un-swept is known as an unfavorable phenomenon during flooding trials.Generally,instability at the interface due to disturbances in porous medium promotes viscous fingering phenomenon.Connate water makes viscous fingers longer and more irregular consisting of large number of tributaries leading to the ultimate oil recovery reduction.Therefore,higher in-situ water content can worsen this condition.Besides,this water can play as a barrier between oil and gas phases and adversely affect the gas diffusion,which results in EOR reduction.On the other hand,from gas storage point of view,it should be noted that CO2 solubility is not the same in the water and oil phases.In this study for a specified water salinity,the effects of different connate water saturations(Swc)on the ultimate oil recovery and CO2 storage capacity during secondary CWI are being presented using carbonate rock samples from one of Iranian carbonate oil reservoir.The results showed higher oil recovery and CO2 storage in the case of lower connate water saturation,as 14%reduction of Swc resulted in 20%and 16%higher oil recovery and CO2 storage capacity,respectively.

Factors influencing oil recovery by surfactant-polymer flooding in conglomerate reservoirs and its quantitative calculation method

This study aims to clarify the factors influencing oil recovery of surfactant-polymer(SP)flooding and to establish a quantitative calculation model of oil recovery during different displacement stages from water flooding to SP flooding.The conglomerate reservoir of the Badaowan Formation in the seventh block of the Karamay Oilfield is selected as the research object to reveal the start-up mechanism of residual oil and determine the controlling factors of oil recovery through SP flooding experiments of natural cores and microetching models.The experimental results are used to identify four types of residual oil after water flooding in this conglomerate reservoir with a complex pore structure:oil droplets retained in pore throats by capillary forces,oil cluster trapped at the junction of pores and throats,oil film on the rock surface,isolated oil in dead-ends of flow channel.For the four types of residual oil identified,the SP solution can enhance oil recovery by enlarging the sweep volume and improving the oil displacement efficiency.First,the viscosity-increasing effect of the polymer can effectively reduce the permeability of the displacement liquid phase,change the oil-water mobility ratio,and increase the water absorption.Furthermore,the stronger the shear drag force of the SP solution,the more the crude oil in a porous medium is displaced.Second,the surfactant can change the rock wettability and reduce the absorption capacity of residual oil by lowering interfacial tension.At the same time,the emulsification further increases the viscosity of the SP solution,and the residual oil is recovered effectively under the combined effect of the above two factors.For the four start-up mechanisms of residual oil identified after water flooding,enlarging the sweep volume and improving the oil displacement efficiency are interdependent,but their contribution to enhanced oil recovery are different.The SP flooding system primarily enlarges the sweep volume by increasing viscosity of solution to start two kinds of residual oil such as oil droplet retained in pore throats and isolated oil in dead-ends of flow channel,and primarily improves the oil displacement efficiency by lowing interfacial tension of oil phase to start two kinds of residual oil such as oil cluster trapped at the junction of pores and oil film on the rock surface.On this basis,the experimental results of the oil displacement from seven natural cores show that the pore structure of the reservoir is the main factor influencing water flooding recovery,while the physical properties and original oil saturation have relatively little influence.The main factor influencing SP flooding recovery is the physical and chemical properties of the solution itself,which primarily control the interfacial tension and solution viscosity in the reservoir.The residual oil saturation after water flooding is the material basis of SP flooding,and it is the second-most dominant factor controlling oil recovery.Combined with the analysis results of the influencing factors and reservoir parameters,the water flooding recovery index and SP flooding recovery index are defined to further establish quantitative calculation models of oil recovery under different displacement modes.The average relative errors of the two models are 4.4%and 2.5%,respectively;thus,they can accurately predict the oil recovery of different displacement stages and the ultimate reservoir oil recovery.

Donghe Sandstone Subtle Reservoir Exploration and Development Technology in Hade 4 Oilfield

Hade 4 oilfield is located on the Hadexun tectonic belt north of the Manjiaer depression in the Tarim basin, whose main target layer is the Donghe sandstone reservoir, with a burial depth over 5,000m and an amplitude below 34m, at the bottom of the Carboniferous. The Donghe sandstone reservoir consists of littoral facies deposited quartz sandstones of the transgressive system tract, overlapping northward and pinching out. Exploration and development confirms that water-oil contact tilts from the southeast to the northwest with a drop height of nearly 80m. The reservoir, under the control of both the stratigraphic overlap pinch-out and tectonism, is a typical subtle reservoir. The Donghe sandstone reservoir in Hade 4 oilfield also has the feature of a large oil-bearing area (over 130 km2 proved), a small thickness (average efficient thickness below 6m) and a low abundance (below 50 × 104t/km2). Moreover, above the target layer developed a set of igneous rocks with an uneven thickness in the Permian formation, thus causing a great difficulty in research of the velocity field. Considering these features, an combination mode of exploration and development is adopted, namely by way of whole deployment, step-by-step enforcement and rolling development with key problems to be tackled, in order to further deepen the understanding and enlarge the fruits of exploration and development. The paper technically focuses its study on the following four aspects concerning problem tackling. First, to strengthen the collecting, processing and explanation of seismic data, improve the resolution, accurately recognize the pinch-out line of the Donghe sandstone reservoir by combining the drilling materials in order to make sure its distribution law; second, to strengthen the research on velocity field, improve the accuracy of variable speed mapping, make corrections by the data from newly- drilled key wells and, as a result, the precision of tectonic description is greatly improved; third, to strengthen the research on sequence stratigraphy and make sure the distribution law of the Donghe sandstone; and fourth, with a step- by-step extrapolation method, to deepen the cognition of the leaning water-oil contact, and by combining the tectonic description and drilling results, to make sure little by little the law of change of the water-oil contact. The exploration and development of the Donghe sandstone subtle reservoir in Hade 4 oilfield is a gradually perfected process. From 1998 when it was discovered till now, the reservoir has managed to make a benign circle of exploration and development, in which its reserve has gradually been enlarged, its production scale increased, and, in a word, it has used techniques necessary for this subtle reservoir in the Tarim basin.

Water-cut rising mechanism and optimized water injection technology for deepwater turbidite sandstone oilfield: A case study of AKPO Oilfield in Niger Delta Basin, West Africa

Through the analysis of the reservoir connection relationship and the water-cut rising rules after water breakthrough in the highly volatile oil AKPO oilfield, a new model of water-cut rising was established, and the timing and strategy of water injection were put forward. The water-cut rising shapes of producers after water breakthrough can be divided into three types, and their water-cut rising mechanism is mainly controlled by reservoir connectivity. For the producers which directly connect with injectors in the single-phase sand body of the single-phase channel or lobe with good reservoir connectivity, the water-cut rising curve is "sub-convex". For the producers which connect with injectors through sand bodies developed in multi-phases with good inner sand connectivity but poorer physical property and connectivity at the overlapping parts of sands, the response to water injection is slow and the water-cut rising curve is "sub-concave". For the producers which connect with injectors through multi-phase sand bodies with reservoir physical properties, connectivity in between the former two and characteristics of both direct connection and overlapping connection, the response to water injection is slightly slower and the water-cut rising curve is "sub-S". Based on ratio relationship of oil and water relative permeability, a new model of water cut rising was established. Through the fitting analysis of actual production data, the optimal timing and corresponding technology for water injection after water breakthrough were put forward. Composite channel and lobe reservoirs can adopt water injection strategies concentrating on improving the vertical sweep efficiency and areal sweep efficiency respectively. This technology has worked well in the AKPO oilfield and can guide the development of similar oilfields.

Application Research of Oil Development Costs in Reservoir Management

Based on oil development costs, the application research in the technical and economic limits calculation of oil development and the production optimal allocation to all the oilfields, was finished. At the same time, according to the regression of real development costs, a new method for oil well economic water cut and oil well economic rate are set up, the production optimal allocation is developed with satisfactory results.

Development and applications of solids-free oil-in-water drilling fluids

The increasing application of near balanced drilling technology to low-pressure and depleted fractured reservoirs requires the use of low-density drilling fluids to avoid formation damage. Solidsfree oil-in-water （O/W） emulsion drilling fluid is one type of low-density drilling fluid suitable for depleted fractured reservoirs. In this paper, the solids-free O/W drilling fluid was developed and has been successfully used in the Bozhong 28-1 oil and gas field, by which lost circulation, a severe problem occurred previously when drilling into fractured reservoir beds, was controlled, thereby minimizing formation damage. The O/W emulsion drilling fluid was prepared by adding 20% （by volume） No. 5 mineral oil （with high flash point, as dispersed phase） into seawater （as continuous phase）. Surfactant HTO-1 （as a primary emulsifier） and non-ionic surfactant HTO-2 （as a secondary emulsifier） were added into the drilling fluid system to stabilize the emulsion; and YJD polymer was also added to seawater to improve the viscosity of the continuous phase （seawater）. The drilling fluid was characterized by high flash point, good thermal stability and high stability to crude oil contamination.

Diagenetic evolution and effects on reservoir development of the Dengying and Longwangmiao formations,Central Sichuan Basin,Southwestern China

The deeply buried Lower Cambrian Longwangmiao Formation and Upper Ediacaran Dengying Formation from the Sichuan Basin,China,have a total natural gas reserve up to 3×10^(12)m^(3).The complex diagenetic evolution and their impacts on the present-day reservoir quality have not been systematically elucidated,hampering the current exploration.Crucially,the integration and comparation diagenetic study on these two formations,which may be able to shed new lights on reservoir formation mechanism,are yet to be systemically evaluated.By compiling geochemistry data,including carbonate U-Pb ages and petrophysics data,coupled with new petrology,trace elements,and strontium isotope data,of various types of diagenetic carbonates,this study aims to decipher the potential links between diagenesis and reservoir development of both formations.Intriguingly,similar diagenetic sequence,which contains five distinctive dolomite phases,is established in both formations.The matrix dolomite(D1)and early dolomite cement(D2)were likely formed by reflux dolomitization,as inferred by their nearly syn-depositional U-Pb ages and elevatedδ^(18)O caused by seawater evaporation.The subsequent moderate burial dolomite cement(D3)was most plausibly the product of burial compaction as indicated by its lighterδ^(18)O and slightly younger U-Pb ages compared with D1 and D2.Whereas deep burial dolomite cements(D4 and D5)yield markedly depletedδ^(18)O,elevated ^(87)Sr/^(86)Sr,along with much younger U-Pb ages and higher precipitation temperatures,suggesting that they were likely linked to hydrothermal fluids.Despite the wide occurrence of meteoric and organic acids leaching and thermochemical sulfate reduction,they may have only played a subsidiary role on these reservoirs development.Instead,superior reservoir quality is tightly linked to tectonics as inferred by higher reservoir quality closely related to the well-developed fractures and faults filled with abundant hydrothermal minerals.Notably,good reservoirs in both formations are mainly attributed to high permeability caused by tectonics.Hence,this new contribution emphasizes the crucial role of tectonics on spatially explicit reservoir prediction of deep to ultra-deep(up to>8000 m)carbonates in the Sichuan Basin,as well as other sedimentary basin analogues in China.

Geochemical Characteristics of Oilfield Waters fromthe Turpan Depression, Xinjiang and Their Petroleum Geological Significance

This paper, based on the fundamental inorganic chemical and organic geochemical characteristics of oilfield waters from the Turpan Depression, presents the contents of organic matter, the distribution of low-carbon fatty acids and the contents of aromatic hydrocarbons as well as their principal ultraviolet absorption spectral and fluorescence spectral characteristics in oilfield waters from different oil/gas-bearing areas. The oil/gas reservoirs in this depression are classified in terms of their conserving conditions. In addition, the paper also discusses the chemical characteristics of oilfield waters from different types of oil/gas reservoirs with an emphasis on the characteristics of their localization in the γ_Na/γCa-γNa/γ_Cl correction diagram. On this basis it is attempted to expound the fundamental geochemical characteristics of oilfield waters from the Turpan Depression and their geological significance.

Development Plan of East Unity Oil Field, Sudan, Using Reservoir Simulation Study

Simulation study was applied in the development planning of East Unity oilfield, Sudan. A grid consisting of 2 000 cells was constructed. A major challenge of the study wasto evolve a full field development and future reservoir management strategy that would ensuremaximum recovery of oil based on well Un51. Simulation shows that Un51 as injection well inAradiebaC would yield better oil recovery than to be production well.