The effects of different flow forms on an opposed-piston two-stroke（OPTS）gasoline-directinjection（GDI）engine was studied by analyzing the mixture formation and combustion.Swirl was broken and dissipated gradually ...The effects of different flow forms on an opposed-piston two-stroke（OPTS）gasoline-directinjection（GDI）engine was studied by analyzing the mixture formation and combustion.Swirl was broken and dissipated gradually and the turbulence kinetic energy（TKE）was small in the compression process;however,tumble was strengthened and the TKE was strong in the compression process.For swirl around X axis（the axis of cylinder）and tumble around Y axis（the vertical direction of injector）,droplets were attached to the cylinder liner by the centrifugal force and the mixture distribution was poor.For tumble around Zaxis（the direction of injector）,the wall film in cylinder liner was thin and mixture distribution was homogeneous.Results showed that since the injector were installed on the wall of the cylinder liner in the OPTS-GDI engine,the spray angle was small and the mixture formation time was short.The 45° oblique axis tumble ratio of 1 was reasonable for the mixture formation and combustion for an OPTS-GDI engine.展开更多
In order to improve the fuel consumption and exhaust emission for gasoline engines,gasoline direct injection（GDI） system is spotlighted to solve these requirements.Thus,many researchers focus on the investigation of...In order to improve the fuel consumption and exhaust emission for gasoline engines,gasoline direct injection（GDI） system is spotlighted to solve these requirements.Thus,many researchers focus on the investigation of spray characteristics and the fuel formation of GDI injector.This paper presents a complete numerical and experimental characterization of transient gasoline spray from a high pressure injection system equipped with a modern single-hole electric controlled injector in a pressurized constant volume vessel.The numerical analysis is carried out in a one-dimensional model of fuel injection system which is developed in the AVL HYDSIM environment.The experimental analyses are implemented through a self-developed injection rate measurement device and spray evolution visualization system.The experimental results of injection rate and spray dynamics are taken to tune and validate the built model.The visualization system synchronize a high speed CMOS camera to obtain the spray structure,moreover,the captured images are taken to validate the injector needle lift process which is simulated in the model.The reliability of the built model is demonstrated by comparing the numerical results with the experimental data.The formed vortex structure at 0.8 ms is effectively disintegrated at 6.2 ms and the spray dynamics become rather chaotic.The fuel flow characteristics within injector nozzle extremely influence the subsequent spray evolution,and therefore this point should be reconsidered when building hybrid breakup GDI spray model.The spray tip speed reach the maximum at 1.18 ms regardless of the operation conditions and this is only determined by the injector itself.Furthermore,an empirical equation for the spray tip penetration is obtained and good agreement with the measured results is reached at a certain extent.This paper provides a methodology for the investigation of spray behavior and fuel distribution of GDI engine design.展开更多
As one of the most important actuators for gasoline direct injection technology,common rail systems provide the requested rail pressure for fuel injection.Special system characteristics,such as coupled discrete-contin...As one of the most important actuators for gasoline direct injection technology,common rail systems provide the requested rail pressure for fuel injection.Special system characteristics,such as coupled discrete-continuous dynamic in the common rail system,limited measurable states,and time-varying engine operating conditions,impel the combination of advanced methods to obtain the desired injection pressure.Therefore,reducing the pressure fluctuation and satisfying engineering implementation have become noteworthy issues for rail pressure control(RPC)systems.In this study,the benchmark problem and the design specification of RPC proposed by 2018 IFAC E-CoSM Committee are introduced.Moreover,a common rail system model is provided to the challengers,and a traditional PI control is applied to show the problem behaviors.Finally,intermediate results of the challengers are summarized briefly.展开更多
基金Supported by the National Natural Science Foundation of China(B2220110005)
文摘The effects of different flow forms on an opposed-piston two-stroke（OPTS）gasoline-directinjection（GDI）engine was studied by analyzing the mixture formation and combustion.Swirl was broken and dissipated gradually and the turbulence kinetic energy（TKE）was small in the compression process;however,tumble was strengthened and the TKE was strong in the compression process.For swirl around X axis（the axis of cylinder）and tumble around Y axis（the vertical direction of injector）,droplets were attached to the cylinder liner by the centrifugal force and the mixture distribution was poor.For tumble around Zaxis（the direction of injector）,the wall film in cylinder liner was thin and mixture distribution was homogeneous.Results showed that since the injector were installed on the wall of the cylinder liner in the OPTS-GDI engine,the spray angle was small and the mixture formation time was short.The 45° oblique axis tumble ratio of 1 was reasonable for the mixture formation and combustion for an OPTS-GDI engine.
基金supported by China First Auto Works Group Corporation R&D Center Program (Grant No. 56067028)
文摘In order to improve the fuel consumption and exhaust emission for gasoline engines,gasoline direct injection（GDI） system is spotlighted to solve these requirements.Thus,many researchers focus on the investigation of spray characteristics and the fuel formation of GDI injector.This paper presents a complete numerical and experimental characterization of transient gasoline spray from a high pressure injection system equipped with a modern single-hole electric controlled injector in a pressurized constant volume vessel.The numerical analysis is carried out in a one-dimensional model of fuel injection system which is developed in the AVL HYDSIM environment.The experimental analyses are implemented through a self-developed injection rate measurement device and spray evolution visualization system.The experimental results of injection rate and spray dynamics are taken to tune and validate the built model.The visualization system synchronize a high speed CMOS camera to obtain the spray structure,moreover,the captured images are taken to validate the injector needle lift process which is simulated in the model.The reliability of the built model is demonstrated by comparing the numerical results with the experimental data.The formed vortex structure at 0.8 ms is effectively disintegrated at 6.2 ms and the spray dynamics become rather chaotic.The fuel flow characteristics within injector nozzle extremely influence the subsequent spray evolution,and therefore this point should be reconsidered when building hybrid breakup GDI spray model.The spray tip speed reach the maximum at 1.18 ms regardless of the operation conditions and this is only determined by the injector itself.Furthermore,an empirical equation for the spray tip penetration is obtained and good agreement with the measured results is reached at a certain extent.This paper provides a methodology for the investigation of spray behavior and fuel distribution of GDI engine design.
基金the National Nature Science Foundation of China(Nos.61790564,61803173)the Program for Natural Science Foundation of Jilin Province(No.20190103047JH).
文摘As one of the most important actuators for gasoline direct injection technology,common rail systems provide the requested rail pressure for fuel injection.Special system characteristics,such as coupled discrete-continuous dynamic in the common rail system,limited measurable states,and time-varying engine operating conditions,impel the combination of advanced methods to obtain the desired injection pressure.Therefore,reducing the pressure fluctuation and satisfying engineering implementation have become noteworthy issues for rail pressure control(RPC)systems.In this study,the benchmark problem and the design specification of RPC proposed by 2018 IFAC E-CoSM Committee are introduced.Moreover,a common rail system model is provided to the challengers,and a traditional PI control is applied to show the problem behaviors.Finally,intermediate results of the challengers are summarized briefly.
