To address the issues of reduced performance and shortened lifespan during the low-carbonizating process of Al_(2)O_(3)-C refractories,nano-crystalline ZrC modified graphite was prepared using Zr powder and flake grap...To address the issues of reduced performance and shortened lifespan during the low-carbonizating process of Al_(2)O_(3)-C refractories,nano-crystalline ZrC modified graphite was prepared using Zr powder and flake graphite as raw materials,with NaCl and NaF mixed salt serving as the medium.The flake graphite was gradually replaced by ZrC modified graphite in the preparation of Al_(2)O_(3)-C refractories,and its impact on the material’s structure and properties was investigated.The results indicate that,compared to samples with only flake graphite,the introduction of 1 mass%to 5 mass%nano-crystalline ZrC modified graphite can significantly enhance the mechanical performance of low-carbon Al_(2)O_(3)-C refractories.When 5 mass%ZrC modified graphite is added,the mechanical properties of the samples are optimal,with the cold modulus of rupture and elastic modulus reaching 22.5 MPa and 65.0 GPa,respectively.展开更多
This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_...This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/graphite batteries.After 450 cycles at room temperature(25℃),the discharge capacity retentions of batteries with blank and PHIS-containing electrolyte are 56.03%and 94.92%respectively.After 230 cycles at high temperatures(45℃),their values are 75.30%and 88.38%respectively.The enhanced electrochemical performance of the batteries with PHIS-containing electrolyte is supported by the spectroscopic characterization and theoretical calculations.It is demonstrated that this PHIS electrolyte additive can facilitate the construction of the electrode interface films,remove the H2O/HF in the electrolyte,and improve the electrochemical performance of the batteries.This work not only develops a sulfonate-based electrolyte but also can stimulate new ideas of functional additives to improve the battery performance.展开更多
A novel nano-SnO2/graphite electrode has been prepared via polishing procedure to produce active and stable surface. The modified electrode resolves the overlapping voltammetric response of dopamine and ascorbic acid...A novel nano-SnO2/graphite electrode has been prepared via polishing procedure to produce active and stable surface. The modified electrode resolves the overlapping voltammetric response of dopamine and ascorbic acid into two well-defined peaks by 230 mV. The mechanism of discrimination of dopamine from ascorbic acid is discussed. Dopamine and ascorbic acid can be determined simultaneously with the modified electrode. The electrode shows good sensitivity, selectivity and stability.展开更多
Four kinds of Cu-based composites with different mass ratios of graphite and WS2 as lubricants were fabricated by hot-pressing method. Electrical sliding wear behaviors of the composites were investigated using a bloc...Four kinds of Cu-based composites with different mass ratios of graphite and WS2 as lubricants were fabricated by hot-pressing method. Electrical sliding wear behaviors of the composites were investigated using a block-on-ring tribometer rubbing against Cu-5%Ag alloy ring. The results demonstrated that 800 ~C was the optimum sintering temperature for Cu-graphite-WS2 dual-lubricant composites to obtain the best comprehensive properties of mechanical strength and lubrication performance. Contact voltage drops of the Cu-based composites increased with increasing the mass ratio of WS2 to graphite. The Cu-based composite with 20% graphite and 10% WS2 showed the best wear resistance due to the excellent synergetic lubricating effect of graphite and WS2. The reasonable addition of WS2 into the Cu-graphite composite can remarkably improve the wear resistance without much rise of electrical energy loss which provides a novel principle of designing suitable sliding electrical contact materials for industrial applications.展开更多
In order to reduce the friction coefficients and improve the wear resistance of mechanical parts, which work in the severe friction and wear conditions at heavy loads, the graphite/CaFg/TiC/Ni-base alloy composite coa...In order to reduce the friction coefficients and improve the wear resistance of mechanical parts, which work in the severe friction and wear conditions at heavy loads, the graphite/CaFg/TiC/Ni-base alloy composite coatings were prepared by plasma spray and their tribological behavior and mechanisms were investigated. The results show that the friction coefficients of the composite coatings are in the range of 0.22-0.288, which are reduced by 25.9% to 53% compared with those of the pure Ni-base alloy coatings, and the wear rates of the former are 18.6%-70.1% less than those of the latter. When wear against GCr15 steel balls, a transferred layer mainly composed of ferric oxides, graphite and CaF2 may gradually develop on the worn surface of the composite coatings, which made the friction and wear between GCr15 steel ball and the composite coatings change into that between the former and the transferred layer. So the friction coefficients and the wear lubrication effect of the transferred layer. The main wear layer in friction process. rates of the composite coatings are greatly reduced because of the solid mechanism of the composite coatings is delamination of the transferred展开更多
Modified coatings including carbide of iron, nickel, chromium, silicon, and titanium are obtained on 9Cr18 stainless steel surface by laser alloying. The processing method, the microstructure, the interface, the tribo...Modified coatings including carbide of iron, nickel, chromium, silicon, and titanium are obtained on 9Cr18 stainless steel surface by laser alloying. The processing method, the microstructure, the interface, the tribological properties, and the forming mechanisms of the coatings are analyzed. The results show that the microstructure of the alloyed coatings is mainly irregular FeC crystals. Carbides of chromium and iron are around the FeC crystals. Small granular TiC disperses in the alloyed coatings. The microhardness of the alloyed coatings is greatly improved because of the occurrence of carbide with high hardness. At the same time, the wear resistance of the alloyed coatings are higher than that of 9Cr18 stainless steel.展开更多
A Ni Fe_2O_4/expanded graphite(Ni Fe_2O_4/EG)nanocomposite was prepared via a simple and inexpensive synthesis method. Its lithium storage properties were studied with the goal of applying it as an anode in a lithium-...A Ni Fe_2O_4/expanded graphite(Ni Fe_2O_4/EG)nanocomposite was prepared via a simple and inexpensive synthesis method. Its lithium storage properties were studied with the goal of applying it as an anode in a lithium-ion battery. The obtained nanocomposite exhibited a good cycle performance, with a capacity of 601 m Ah g^(-1)at a current of 1 A g^(-1)after 800 cycles. This good performance may beattributed to the enhanced electrical conductivity and layered structure of the EG. Its high mechanical strength could postpone the disintegration of the nanocomposite structure,efficiently accommodate volume changes in the Ni Fe_2O_4-based anodes, and alleviate aggregation of Ni Fe_2O_4 nanoparticles.展开更多
By loading nanometer anatase onto exfoliated graphite with the sol-gel method, exfoliated graphite-TiO2 composite （EG-TiO2） can be prepared, which can adsorb oil and can also degrade oil. In a technologic condition ...By loading nanometer anatase onto exfoliated graphite with the sol-gel method, exfoliated graphite-TiO2 composite （EG-TiO2） can be prepared, which can adsorb oil and can also degrade oil. In a technologic condition for preparing EG-TiO2, the impregnated number of times is the most important factor to influence oil-adsorbing capability, that is, when the impregnated number of times increases, the amount of saturation-adsorbed oil decreases. The study of EG-TiO2 photocatalytic degradation of machine oil based on the weight-loss method and infrared spectrum method indicates that EG-TiO2 has obvious effect of photocatalytic degradation for machine oil. Its performance is superior to pure nanometer TiO2 powder because nanometer TiO2 in EG-TiO2 has three-dimension laminar structure and comparatively high adsorption capability.展开更多
A flower-like SnO_(2)–SnO/porous Ga N(FSS/PGaN) heterojunction was fabricated for the first time via a facile spraying process, and the whole process also involved hydrothermal preparation of FSS and electrochemical ...A flower-like SnO_(2)–SnO/porous Ga N(FSS/PGaN) heterojunction was fabricated for the first time via a facile spraying process, and the whole process also involved hydrothermal preparation of FSS and electrochemical wet etching of GaN,and SnO_(2)–SnO composites with p–n junctions were loaded onto PGaN surface directly applied to H_(2)S sensor. Meanwhile,the excellent transport capability of heterojunction between FSS and PGaN facilitates electron transfer, that is, a response time as short as 65 s and a release time up to 27 s can be achieved merely at 150℃ under 50 ppm H_(2)S concentration, which has laid a reasonable theoretical and experimental foundation for the subsequent PGaN-based heterojunction gas sensor.The lowering working temperature and high sensitivity(23.5 at 200 ppm H2S) are attributed to the structure of PGaN itself and the heterojunction between SnO_(2)–SnO and PGaN. In addition, the as-obtained sensor showed ultra-high test stability.The simple design strategy of FSS/PGaN-based H_(2)S sensor highlights its potential in various applications.展开更多
All-solid-state electrolytes are exceedingly attractive because of the outstanding inherent safety and energy density compared to liquid electrolytes.Whereas,it is still formidable to simultaneously design solid elect...All-solid-state electrolytes are exceedingly attractive because of the outstanding inherent safety and energy density compared to liquid electrolytes.Whereas,it is still formidable to simultaneously design solid electrolytes with favorable electrode/electrolyte interface compatibility and high ionic conductivity in a simple and scalable manner.Hence,the oxygen-vacancy-rich Gd-doped SnO_(2) nanotubes(GDS NTs)are innovatively prepared and applied to the electrolyte of all-solid-state lithium metal batteries for the first time.The addition of GDS NTs can validly construct long-range co ntinuous ion transport networks in the poly(ethylene oxide)(PEO)-based system and greatly improve the mechanical properties of the electrolyte.Compared to the PEO-based electrolyte,the composite electrolyte displays a higher lithium ion conductivity of 2.41×10^(-4) S cm^(-1) at 30℃,a higher lithium ion transference number up to 0.62 and a wider electrochemical window of 5 V at 50℃.In addition,the composite electrolyte manifests outstanding compatibility with high-voltage LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2)(NMC811)cathode,LiFePO4 cathode and lithium metal anode.The assembled Li/Li symmetric battery exhibits stable Li plating/stripping cycling performance,which can cycle steadily for 1500 h at a capacity of 0.3 mA h cm^(-2).And Li/LiFePO4 battery still maintains a high capacity of 131.54 mA h g^(-1) at 0.5C after 800 cycles,which has a superior capacity retention rate of 93.2%.The obtained novel composite electrolyte has promising application prospects in the field of all-solid-state lithium metal cells.展开更多
With constant enlargement of the application areas of the spherical plain bearings,higher quality lubrication of the bearings is required.To solve the lubricating problems of spherical plain bearings under high temper...With constant enlargement of the application areas of the spherical plain bearings,higher quality lubrication of the bearings is required.To solve the lubricating problems of spherical plain bearings under high temperature,high vacuum,high speed,heavy loads and strong oxidation conditions,it is urgent for us to develop more excellent self-lubricating technologies.In this paper,the bonded solid lubricant coatings,which use inorganic phosphate as the binder,the mixture of MoS2 and graphite with two different weight proportions as the solid lubricant,are prepared by spraying under three different spray gun pressures.The bonding strength tests on the coatings show that the best spraying pressure is 0.2 MPa and the better mixing proportion of MoS2 to Graphite is 3：1.Then for the radial spherical plain bearings with steel/steel friction pair,after the coatings are made on the inner ring outer surfaces,the friction coefficient,the wear loss and the friction temperature of the bearings under four oscillating frequencies are investigated by a self-made tribo-tester.The test results,SEM of the worn morphologies and EDS of worn areas show that tribological properties of the bearing are obviously improved by the bonded solid lubricant coatings.When sprayed under the spray gun pressure of 0.2 MPa,the bearings have better anti-friction and anti-wear properties than those sprayed under 0.1 MPa and 0.3 MPa.Further as proved from the XPS analysis,between the coating with 3：1 mixing ratio of MoS2 to Graphite and the coating with 1：1 ratio,the former has less oxidation occurred on the surface and therefore has better tribological characteristics than the latter.This paper provides a reference to developing a new product of the radial spherical plain bearings with high bonding strength,oxidation resistance and abrasion resistance.展开更多
MoS2 is a promising anode material for sodium ion batteries owing to its two-dimensional layered structure and high specific capacity. But it still exhibits a poor cycle stability and limited rate capability for Na＋ ...MoS2 is a promising anode material for sodium ion batteries owing to its two-dimensional layered structure and high specific capacity. But it still exhibits a poor cycle stability and limited rate capability for Na＋ storage because of its poor electrical conductivity and structural instability. In this work, MoS2/graphite composite is fabricated by mechanically delaminated and restacked MoS2 and graphite to form two-dimensional composite layers. The graphite sheets will improve electrical conductivity and prevent the aggregation as well as structure collapse of the MoS2 layers during charge-discharge process. The MoS2/graphite composite exhibits excellent Na＋ storage properties. It delivers a high discharge specific capacity of 358.2 mAh/g at a current density of 100 mA]g in the first discharge process and with capacity retention of 68.1% after 800 cycles （retains 244 mAh/g）. The average discharge specific capacities retain 250.9 and 225.4 mAh/g corresponding to the current densities of 100 and 1000 mA]g, showing excellent rate capability. The improved electrochemical performance is attributed to the improved electrical conductivity and structural stability after composition of graphite sheets. The study demonstrates a new research strategy for improving sodium ion storage properties of Mo52.展开更多
In order to improve the wetting properties of graphite with Al melt and reduce the oxidation of the graphite, by which the segregation of components during the liquid-stir-casting process could be prevented. In this p...In order to improve the wetting properties of graphite with Al melt and reduce the oxidation of the graphite, by which the segregation of components during the liquid-stir-casting process could be prevented. In this paper, a uniform thin nano-film of CeO2, about 20 nm thick, was successfully prepared onto graphite powder surface by heterogeneous nu-cleation process. The results show that an obvious chemical reaction did exit between CeO2 film and graphite with the formation of Ce-O-C bond, leading to a shift of the binding energy of C and Ce. The cover with CeO2 film illustrates a distinct change of surface state of graphite with a decrease of angle of contact.展开更多
The antiwear and antifriction coating, which contains TiB2 and Nickel-coated graphite, has been obtained on stainless steel 9Cr18 by laser cladding. The processing method, microstructure, interface, microhardness, tri...The antiwear and antifriction coating, which contains TiB2 and Nickel-coated graphite, has been obtained on stainless steel 9Cr18 by laser cladding. The processing method, microstructure, interface, microhardness, tribological properties and the forming mechanisms of the coating are analyzed. Results show that the microstructure of the clad coating are mainly long plume-like primary phase sosoloid Ni-Fe which form the matrix framework, while the in-situ anomalous synthetical TiC grains and uhrafine TiB2 grains uniformly disperse among the framework. The hardness and wear resistance of the coating has been greatly improved, which can be attributed to the reinforcement mechanism of TiC, TiB2, FeC, Fe3C and Cr23 C6. etc. At the same time, the coating has friction-reducing ability.展开更多
文摘To address the issues of reduced performance and shortened lifespan during the low-carbonizating process of Al_(2)O_(3)-C refractories,nano-crystalline ZrC modified graphite was prepared using Zr powder and flake graphite as raw materials,with NaCl and NaF mixed salt serving as the medium.The flake graphite was gradually replaced by ZrC modified graphite in the preparation of Al_(2)O_(3)-C refractories,and its impact on the material’s structure and properties was investigated.The results indicate that,compared to samples with only flake graphite,the introduction of 1 mass%to 5 mass%nano-crystalline ZrC modified graphite can significantly enhance the mechanical performance of low-carbon Al_(2)O_(3)-C refractories.When 5 mass%ZrC modified graphite is added,the mechanical properties of the samples are optimal,with the cold modulus of rupture and elastic modulus reaching 22.5 MPa and 65.0 GPa,respectively.
基金financially supported by the Scientific and Technological Plan Projects of Guangzhou City(202103040001)。
文摘This work develops 2-Phenyl-1H-imidazole-1-sulfonate(PHIS)as a multi-functional electrolyte additive for H2O/HF scavenging and film formation to improve the high temperature performance of LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)/graphite batteries.After 450 cycles at room temperature(25℃),the discharge capacity retentions of batteries with blank and PHIS-containing electrolyte are 56.03%and 94.92%respectively.After 230 cycles at high temperatures(45℃),their values are 75.30%and 88.38%respectively.The enhanced electrochemical performance of the batteries with PHIS-containing electrolyte is supported by the spectroscopic characterization and theoretical calculations.It is demonstrated that this PHIS electrolyte additive can facilitate the construction of the electrode interface films,remove the H2O/HF in the electrolyte,and improve the electrochemical performance of the batteries.This work not only develops a sulfonate-based electrolyte but also can stimulate new ideas of functional additives to improve the battery performance.
文摘A novel nano-SnO2/graphite electrode has been prepared via polishing procedure to produce active and stable surface. The modified electrode resolves the overlapping voltammetric response of dopamine and ascorbic acid into two well-defined peaks by 230 mV. The mechanism of discrimination of dopamine from ascorbic acid is discussed. Dopamine and ascorbic acid can be determined simultaneously with the modified electrode. The electrode shows good sensitivity, selectivity and stability.
基金Projects(9102601860979017) supported by the National Natural Science Foundation of ChinaProject(20110111110015) supported by the Doctoral Fund of Ministry of Education of China
文摘Four kinds of Cu-based composites with different mass ratios of graphite and WS2 as lubricants were fabricated by hot-pressing method. Electrical sliding wear behaviors of the composites were investigated using a block-on-ring tribometer rubbing against Cu-5%Ag alloy ring. The results demonstrated that 800 ~C was the optimum sintering temperature for Cu-graphite-WS2 dual-lubricant composites to obtain the best comprehensive properties of mechanical strength and lubrication performance. Contact voltage drops of the Cu-based composites increased with increasing the mass ratio of WS2 to graphite. The Cu-based composite with 20% graphite and 10% WS2 showed the best wear resistance due to the excellent synergetic lubricating effect of graphite and WS2. The reasonable addition of WS2 into the Cu-graphite composite can remarkably improve the wear resistance without much rise of electrical energy loss which provides a novel principle of designing suitable sliding electrical contact materials for industrial applications.
文摘In order to reduce the friction coefficients and improve the wear resistance of mechanical parts, which work in the severe friction and wear conditions at heavy loads, the graphite/CaFg/TiC/Ni-base alloy composite coatings were prepared by plasma spray and their tribological behavior and mechanisms were investigated. The results show that the friction coefficients of the composite coatings are in the range of 0.22-0.288, which are reduced by 25.9% to 53% compared with those of the pure Ni-base alloy coatings, and the wear rates of the former are 18.6%-70.1% less than those of the latter. When wear against GCr15 steel balls, a transferred layer mainly composed of ferric oxides, graphite and CaF2 may gradually develop on the worn surface of the composite coatings, which made the friction and wear between GCr15 steel ball and the composite coatings change into that between the former and the transferred layer. So the friction coefficients and the wear lubrication effect of the transferred layer. The main wear layer in friction process. rates of the composite coatings are greatly reduced because of the solid mechanism of the composite coatings is delamination of the transferred
基金Item Sponsored by Youth Science Foundation of Heilongjiang(QC06C023)
文摘Modified coatings including carbide of iron, nickel, chromium, silicon, and titanium are obtained on 9Cr18 stainless steel surface by laser alloying. The processing method, the microstructure, the interface, the tribological properties, and the forming mechanisms of the coatings are analyzed. The results show that the microstructure of the alloyed coatings is mainly irregular FeC crystals. Carbides of chromium and iron are around the FeC crystals. Small granular TiC disperses in the alloyed coatings. The microhardness of the alloyed coatings is greatly improved because of the occurrence of carbide with high hardness. At the same time, the wear resistance of the alloyed coatings are higher than that of 9Cr18 stainless steel.
基金support from the National Basic Research Program of China (2014CB239702)National Natural Science Foundation of China (Grant Nos. 21371121, 21506126 and 51502174)+1 种基金Shenzhen Science and Technology Research Foundation (Grant Nos. JCYJ20150324141711645,JCYJ20150324141711616 and JCYJ20150626090504916)China Postdoctoral Science Foundation (2015 M582401 and 2015 M572349)
文摘A Ni Fe_2O_4/expanded graphite(Ni Fe_2O_4/EG)nanocomposite was prepared via a simple and inexpensive synthesis method. Its lithium storage properties were studied with the goal of applying it as an anode in a lithium-ion battery. The obtained nanocomposite exhibited a good cycle performance, with a capacity of 601 m Ah g^(-1)at a current of 1 A g^(-1)after 800 cycles. This good performance may beattributed to the enhanced electrical conductivity and layered structure of the EG. Its high mechanical strength could postpone the disintegration of the nanocomposite structure,efficiently accommodate volume changes in the Ni Fe_2O_4-based anodes, and alleviate aggregation of Ni Fe_2O_4 nanoparticles.
文摘By loading nanometer anatase onto exfoliated graphite with the sol-gel method, exfoliated graphite-TiO2 composite （EG-TiO2） can be prepared, which can adsorb oil and can also degrade oil. In a technologic condition for preparing EG-TiO2, the impregnated number of times is the most important factor to influence oil-adsorbing capability, that is, when the impregnated number of times increases, the amount of saturation-adsorbed oil decreases. The study of EG-TiO2 photocatalytic degradation of machine oil based on the weight-loss method and infrared spectrum method indicates that EG-TiO2 has obvious effect of photocatalytic degradation for machine oil. Its performance is superior to pure nanometer TiO2 powder because nanometer TiO2 in EG-TiO2 has three-dimension laminar structure and comparatively high adsorption capability.
基金supported by the Natural Science Research Start-up Foundation of Recruiting Talents of Nanjing University of Posts and Telecommunications (Grant Nos. XK1060921115 and XK1060921002)Young Scientists Fund of the National Natural Science Foundation of China (Grant No. 62204125)+1 种基金the National Key R&D Program of China (Grant No. 2022YFB3605404)the Natural Science Foundation of Guangdong Province, China (Grant No. 2019A1515010790)。
文摘A flower-like SnO_(2)–SnO/porous Ga N(FSS/PGaN) heterojunction was fabricated for the first time via a facile spraying process, and the whole process also involved hydrothermal preparation of FSS and electrochemical wet etching of GaN,and SnO_(2)–SnO composites with p–n junctions were loaded onto PGaN surface directly applied to H_(2)S sensor. Meanwhile,the excellent transport capability of heterojunction between FSS and PGaN facilitates electron transfer, that is, a response time as short as 65 s and a release time up to 27 s can be achieved merely at 150℃ under 50 ppm H_(2)S concentration, which has laid a reasonable theoretical and experimental foundation for the subsequent PGaN-based heterojunction gas sensor.The lowering working temperature and high sensitivity(23.5 at 200 ppm H2S) are attributed to the structure of PGaN itself and the heterojunction between SnO_(2)–SnO and PGaN. In addition, the as-obtained sensor showed ultra-high test stability.The simple design strategy of FSS/PGaN-based H_(2)S sensor highlights its potential in various applications.
基金supported by the National Natural Science Foundation of China(52203066,51973157,61904123,51873152)the Tianjin Natural Science Foundation(18JCQNJC02900)+3 种基金the Science and Technology Plans of Tianjin(19PTSYJC00010)the Tianjin Research Innovation Project for Postgraduate Students(2021YJSB234)the Science&Technology Development Fund of Tianjin Education Commission for Higher Education(2018KJ196)State Key Laboratory of Membrane and Membrane Separation,Tiangong University。
文摘All-solid-state electrolytes are exceedingly attractive because of the outstanding inherent safety and energy density compared to liquid electrolytes.Whereas,it is still formidable to simultaneously design solid electrolytes with favorable electrode/electrolyte interface compatibility and high ionic conductivity in a simple and scalable manner.Hence,the oxygen-vacancy-rich Gd-doped SnO_(2) nanotubes(GDS NTs)are innovatively prepared and applied to the electrolyte of all-solid-state lithium metal batteries for the first time.The addition of GDS NTs can validly construct long-range co ntinuous ion transport networks in the poly(ethylene oxide)(PEO)-based system and greatly improve the mechanical properties of the electrolyte.Compared to the PEO-based electrolyte,the composite electrolyte displays a higher lithium ion conductivity of 2.41×10^(-4) S cm^(-1) at 30℃,a higher lithium ion transference number up to 0.62 and a wider electrochemical window of 5 V at 50℃.In addition,the composite electrolyte manifests outstanding compatibility with high-voltage LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2)(NMC811)cathode,LiFePO4 cathode and lithium metal anode.The assembled Li/Li symmetric battery exhibits stable Li plating/stripping cycling performance,which can cycle steadily for 1500 h at a capacity of 0.3 mA h cm^(-2).And Li/LiFePO4 battery still maintains a high capacity of 131.54 mA h g^(-1) at 0.5C after 800 cycles,which has a superior capacity retention rate of 93.2%.The obtained novel composite electrolyte has promising application prospects in the field of all-solid-state lithium metal cells.
基金Supported by National Natural Science Foundation of China(Grant No.51275155)Henan Provincial Science and Technology Innovation Outstanding Talent Project of China(Grant No.154200510013)Henan Provincial Innovation and Research Team of Science and Technology in Universities of China(Grant No.13IRTSTHN025)
文摘With constant enlargement of the application areas of the spherical plain bearings,higher quality lubrication of the bearings is required.To solve the lubricating problems of spherical plain bearings under high temperature,high vacuum,high speed,heavy loads and strong oxidation conditions,it is urgent for us to develop more excellent self-lubricating technologies.In this paper,the bonded solid lubricant coatings,which use inorganic phosphate as the binder,the mixture of MoS2 and graphite with two different weight proportions as the solid lubricant,are prepared by spraying under three different spray gun pressures.The bonding strength tests on the coatings show that the best spraying pressure is 0.2 MPa and the better mixing proportion of MoS2 to Graphite is 3：1.Then for the radial spherical plain bearings with steel/steel friction pair,after the coatings are made on the inner ring outer surfaces,the friction coefficient,the wear loss and the friction temperature of the bearings under four oscillating frequencies are investigated by a self-made tribo-tester.The test results,SEM of the worn morphologies and EDS of worn areas show that tribological properties of the bearing are obviously improved by the bonded solid lubricant coatings.When sprayed under the spray gun pressure of 0.2 MPa,the bearings have better anti-friction and anti-wear properties than those sprayed under 0.1 MPa and 0.3 MPa.Further as proved from the XPS analysis,between the coating with 3：1 mixing ratio of MoS2 to Graphite and the coating with 1：1 ratio,the former has less oxidation occurred on the surface and therefore has better tribological characteristics than the latter.This paper provides a reference to developing a new product of the radial spherical plain bearings with high bonding strength,oxidation resistance and abrasion resistance.
基金supported by the National Natural Science Foundation of China(no.21403099)the Natural Science Funds for Distinguished Young Scholars of Gansu Province(no.1606RJDA320)
文摘MoS2 is a promising anode material for sodium ion batteries owing to its two-dimensional layered structure and high specific capacity. But it still exhibits a poor cycle stability and limited rate capability for Na＋ storage because of its poor electrical conductivity and structural instability. In this work, MoS2/graphite composite is fabricated by mechanically delaminated and restacked MoS2 and graphite to form two-dimensional composite layers. The graphite sheets will improve electrical conductivity and prevent the aggregation as well as structure collapse of the MoS2 layers during charge-discharge process. The MoS2/graphite composite exhibits excellent Na＋ storage properties. It delivers a high discharge specific capacity of 358.2 mAh/g at a current density of 100 mA]g in the first discharge process and with capacity retention of 68.1% after 800 cycles （retains 244 mAh/g）. The average discharge specific capacities retain 250.9 and 225.4 mAh/g corresponding to the current densities of 100 and 1000 mA]g, showing excellent rate capability. The improved electrochemical performance is attributed to the improved electrical conductivity and structural stability after composition of graphite sheets. The study demonstrates a new research strategy for improving sodium ion storage properties of Mo52.
基金Project supported by the National '973' Project (G19990649)
文摘In order to improve the wetting properties of graphite with Al melt and reduce the oxidation of the graphite, by which the segregation of components during the liquid-stir-casting process could be prevented. In this paper, a uniform thin nano-film of CeO2, about 20 nm thick, was successfully prepared onto graphite powder surface by heterogeneous nu-cleation process. The results show that an obvious chemical reaction did exit between CeO2 film and graphite with the formation of Ce-O-C bond, leading to a shift of the binding energy of C and Ce. The cover with CeO2 film illustrates a distinct change of surface state of graphite with a decrease of angle of contact.
文摘The antiwear and antifriction coating, which contains TiB2 and Nickel-coated graphite, has been obtained on stainless steel 9Cr18 by laser cladding. The processing method, microstructure, interface, microhardness, tribological properties and the forming mechanisms of the coating are analyzed. Results show that the microstructure of the clad coating are mainly long plume-like primary phase sosoloid Ni-Fe which form the matrix framework, while the in-situ anomalous synthetical TiC grains and uhrafine TiB2 grains uniformly disperse among the framework. The hardness and wear resistance of the coating has been greatly improved, which can be attributed to the reinforcement mechanism of TiC, TiB2, FeC, Fe3C and Cr23 C6. etc. At the same time, the coating has friction-reducing ability.
