Chemical Analysis Method for Carbon Bearing Refractory Products——Determination of the Total Carbon by Combustion Gravimetric Method

GB/T 13245-91 1 Theme and Scope This standard specifies the method abstract, reagents, apparatus, specimen, analyzing procedure, result calculation and permissible tolerance used for determination of the total carbon with combustion gravimetric method.

Chemical Analysis of Magnesia and Magnesia-Alumina Refractory Materials——Gravimetric method for determination of loss on ignition

1 Scope This standard specifies the gravimetric method for determination of loss on ignition.

A study of laboratory testing and calculation methods for coal sorption isotherms

Measurement of the volume of gas adsorbed per unit mass of coal with increasing pressure at a constant temperature produces an isotherm that describes the gas storage capacity of this type of coal. The accurate testing and interpretation of coal sorption isotherm plays an important role in the areas of coal mine methane drainage, coalbed methane （CBM） reservoir resource assessment, enhanced coalbed methane （ECBM） recovery, as well as the carbon dioxide （CO2） sequestration in deep coal seams or similar geological formations. Different coal sorption isotherm testing apparatus and associated calculation methods are critically reviewed and presented in this paper. These include both volumetric and gravimetric based methods, as well as experimental sorption tests with confining stress and direction sorption methods. The volumetric techniques utilise experimental apparatus with sample cell and injection pump and that with both sample cell and reference cell. Whilst the gravimetric approachesinclude methods with sample cell and suspension magnetic balance and that with both sample cell and reference cell. Different testing methods are compared and discussed in this study. A unique in-house-built coal sorption isotherm testing apparatus at the University of Wollongong was presented together with the calculation method, procedures and experimental results. The isotherm results can be calculated by both Soave-Redlich-Kwong （SRK） equation and calibration cure methods which can be used directly to convert the volume of adsorbed gas in different test conditions to standard condition （NTP）.

Geophysical and Petro-Structural Characteristics of the Tarkwaïan and Associated Formations of the Gontougo Region (Northeastern Côte d’Ivoire)

Studies carried out in the Gontougo region aimed to describe the physical and petro-structural properties of the Tarkwaian formations of northeastern Côte d’Ivoire. The methodology developed is focused on the one hand on the gravimetric geophysical method and on the other hand, on petro-structural studies. The geophysical results highlighted two gravimetric facies characterized respectively by high density (ΔBg > 121 mGal) and low density (ΔBg < 114 mGal) anomalies. From a lithological point of view, the denser domains are made up of intrusive rocks dominated by granodiorites and tonalites cutting low density facies composed of Tarkwaian formations (polygenic conglomerates and arkosic sandstones) and volcanics (tuffs and cinerites). Structurally, these different lithological groups are affected by brittle (fractures, faults, strike-slip) and ductile (folds, schistosities and mineral lineations) deformations. These structures are mainly oriented NNW-SSW, WNW-ESE and NE-SW. The description of the sulphide minerals reveals a style of gold mineralization of the Tarkwaian formations.

Die-Swell Performance of Colored Poly(m-phenylene isophthalamide)(PMIA)Fiber Prepared by Wet Spinning

The colored poly(m-phenylene isophthalamide)(PMIA)spinning solution was prepared by wet spinning and the die-swell of the colored PMIA spinning solution was done when it was extruded from a die in this experiment.The properties and structures of colored PMIA fibers were characterized by scanning electron microscopy(SEM).The colored PMIA spinning dopes were first commixed in a pressurizer and then spun into a coagulation bath.The effect of die swell on the colored PMIA solution was resulted from the viscoelastic properties of the colored PMIA solution in the spinning process.The results showed that the die-swell ratio of the colored PMIA solution increased linearly with increasing the pressure and die length/diameter ratio(L/D).At the same pressure and L/D,the die-swell ratio decreased with the increase of filter layers and temperature.Also,optimized spinning parameters of the dopedyed PMIA fiber were obtained.

Curcumin Extract as a Green Inhibitor of Leaching from Aluminum Cookware at Quasi-Cooking Conditions

Curcumin aqueous extract is used successfully as a green corrosion inhibitor at quasi-cooking conditions (90℃) to inhibit leaching from Aluminum cook wares in solutions containing vegetables or meat. Aluminum cook wares were bought from the market from four countries and cut to make the Aluminum samples. Six types of vegetables and three kinds of meat were chosen. Each type of vegetable and meat was used to prepare 30% w/v aqueous solutions. Three methods were used in the present study: Gravimetric method, Atomic Absorption and FTIR. Gravimetric method was applied to determine the leaching rate and the corrosion inhibition efficiency with/without NaCl. The effect of Curcumin concentration, Tab water, immersion time, alloying elements was investigated. There was a good consistency between Gravimetric and Atomic Absorption methods. The adsorption of Curcumin on the aluminum surface was in accordance with Langmuir isotherm. The values of the adsorption constant (Kads) and the free energy of adsorption (Gadso) were calculated and discussed. FTIR spectrum indicated that Curcumin coordinated with Al3+ resulting in the formation of Al3+-Curcumin complex on the metal surface. Using a small amount of Curcumin decreased leaching from Aluminum cook wares into food by 60% - 80% depending about the type of food.

Experimental Investigation of Inhibition Efficiency of Crocin for Chloride-Induced Corrosion of Aluminum Alloys

The use of Crocin, derived from the flowers of Crocus sativus, is investigated as corrosion inhibitor for the AA1050, AA5083, AA5754 and AA6082 aluminum alloys in chloride ions environment. Aluminum and aluminum alloys are subjected to corrosion in the aggressive environment of chlorides, so several green corrosion inhibitors, mostly of plant origin, with minimum impact on health and the environment have been examined. In this study, the inhibition efficiency of 1.25 mM Crocin in a 0.01 M NaCl corrosive solution was assessed via electrochemical corrosion techniques and gravimetric mass loss measurements of the aluminum alloys. The surface of the specimens was examined using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Stereomicroscopy and Glossiness measurements. Experimental results reveal the protective anticorrosive action of Crocin for all aluminum alloys in the sodium chloride medium.

Measurement of Solubilities of o-Phenylphenol in Petroleum Ether and DDP in Acetone+Water Solution

[（6-oxide-6H-dibenze（c, e）（1, 2）oxaphosphorin-6-yl）methyl]-butanedioic acid （DDP） was prepared and characterized. Solubilities of o-phenylphenol（OPP） in petroleum ether and DDP in acetone ＋ water solution were measured by a gravimetrical method. The solubility data of OPP were well correlated using Francis equation. For the solubility of DDP in acetone aqueous solution, it was found that at each fixed temperature there existed a maximum when the acetone mass fraction in the solvent reached a certain concentration. The experiment shows that the fraction is approximately 0.6. The solubility data would be helpful for their industrial crystallization process.