Model test of the group piles foundation of a high-speed railway bridge in mined-out area

The research on the mechanism of pile-soil-cap-goaf interaction and settlement of high-speed railway bridge located in mined-out area is still relatively rare. By taking the pile group of Guanshandi bridge foundation in Hefei- Fuzhou high-speed railway as the prototype, a model test is carried out. According to the similarity theory, the similar constant is derived and the similar model material is determined. Meanwhile, three types of data including the bearing behavior of piles, and the settlement law, and soil among piles are investigated. It can be found that： the influence of goaf on the bearing capacity of pile is inversely to the loading degree, the larger of loading degree, the smaller impact of goaf on the bearing capacity. There is no negative side friction can been found in pile body and the degree of downward tendency for the barycenter of side friction layout is obvious for piles in goaf. Although the bearing ratio of soil resistance under cap is relatively large, the cap effect is suggested be ignored considering the characteristic of goaf. There is a maximum critical value for the uneven settlement of pile group in goaf, and when the value is reached, the uneven settlement stop growing anymore. In addition, the formula for calculating bearing capacity and settlement of pile group in goaf based on test results, theory analysis and related standard is established.

Investigating the Efficiency Coefficient of Pile Group in Clay Under Two-Way Lateral Load

This research investigates the behavior of a 2×2 pile group under two-directional lateral loads in addition to the vertical load.Through three-dimensional numerical modeling based on Flac 3D software,the study examines the total bearing capacity and efficiency coefficient of the pile group,considering factors such as the angle of lateral load,relative pile spacing,and relative stiffness of the pile-soil system.The findings highlight the significance of these factors in understanding and predicting the response of pile groups to changing lateral load directions.The results reveal that increasing the angle of the lateral load from 0°to 45°enhances both the maximum total lateral load and the efficiency coefficient of the pile group.When the relative stiffness of the pile-soil system significantly increases,soil stiffening occurs and reducing the relative spacing of the piles from 7 to 3 times the diameter of the piles diminishes the influence of the pile group.Consequently,the response of the pile group to lateral loads becomes more linear,with only a slight alteration in the maximum total lateral load and the efficiency coefficient when the lateral load is angled from 0°to 45°.Conversely,increasing the relative distance between the piles,specifically from 3 to 7 times the diameter of the piles,amplifies the influence of the pile group.Both the maximum total lateral load and the efficiency coefficient of the pile group exhibit an observed increase.These provide insights for designing pile groups and optimizing their performance under lateral loading conditions.

Effects of non-liquefiable crust layer and superstructure mass on the response of 2×2 pile groups to liquefaction-induced lateral spreading

In this research,two shake table experiments were conducted to study the effects of non-liquefiable crust layer and superstructure mass on the responses of two sets of 22 pile groups to liquefactioninduced lateral spreading.In this regard,an inclined base layer overlain by a very loose liquefiable layer was constructed in both models;while only in one model,a non-liquefiable crust layer was built.A lumped mass,being representative of a superstructure,was attached to the cap of one pile group in both models.The models were fully instrumented with various sensors,including acceleration,displacement,and pore water pressure transducers.Also,the piles were instrumented with pair strain gauges to measure pure bending moments induced by cyclic and monotonic loadings associated with ground shaking and lateral spreading,respectively.The results showed that the existence of the non-liquefiable crust layer increases both the maximum and residual soil displacements at the free field and also the maximum bending moments in the piles.The results of the experiments indicated that the crust layer induces a high kinematic lateral soil pressure and force on the piles which are not present in the crustless case.The crust layer increases the pile cap displacement before liquefaction,albeit decreases it after liquefaction,due to the elastic rebound of the piles in the liquefiable layer.The crust layer postpones both liquefaction triggering and dissipation of excess pore water pressure.The existence of the superstructure mass on the pile caps decreases the acceleration amplitude of the pile caps,while increases their maximum displacement.

Shake table test of soil-pile groups-bridge structure interaction in liquefiable ground

This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground. The soil profile, contained in a large-scale laminar shear box, consisted of a horizontally saturated sand layer overlaid with a silty clay layer, with the simulated low-cap pile groups embedded. The container was excited in three E1 Centro earthquake events of different levels. Test results indicate that excessive pore pressure （EPP） during slight shaking only slightly accumulated, and the accumulation mainly occurred during strong shaking. The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased. The acceleration response of the sand was remarkably influenced by soil liquefaction. As soil liquefaction occurred, the peak sand displacement gradually lagged behind the input acceleration; meanwhile, the sand displacement exhibited an increasing effect on the bending moment of the pile, and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top. A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events. It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun.

Response of a pile group behind quay wall to liquefaction-induced lateral spreading:a shake-table investigation

The response of pile foundations near a quay wall under liquefaction-induced lateral spreading remains a complex problem. This study presents the results of a shake-table test on a 2×2 pile group behind a sheet-pile quay wall that was subjected to lateral spreading. The quay wall was employed to trigger liquefaction-induced large lateral ground deformation. The discussions focus on the behavior of the pile and the soil and on the bending moment distributions within the group pile and the restoring force characteristics at the superstructure. Overall, the piles exhibited apparent pinning effects that reduced soil deformation. In addition, the rear-row piles near the quay wall experienced larger bending moments than did the front-row piles, indicating significant pile group effects. The tests showed that lateral spreading could be a primary cause of larger monotonic deformations and bending moments. It can also be concluded that the monotonic bending moments were significantly decreased due to the presence of slow soil flow. The stiffness at the superstructure was reduced because of accumulated excess pore pressure before liquefaction, and it was recovered during lateral spreading. The present study further enhances current understanding of the behavior of low-cap pile foundations under lateral spreading.

Performance of X-Section Concrete Pile Group in Coral Sand Under Vertical Loading

To reveal the bearing capacity of the X-section pile group in coral sand, a series of model load tests are conducted.The testing results are presented as load-settlement curves, pile-soil stress ratios, distributions of side friction and axial force, and load-sharing ratio between side and tip resistances. The reliability and accuracy of the numerical simulation model are verified by comparing the results of the model test. Comparative analysis between X-section and circular section piles with the same cross-sectional area indicates that the bearing capacity of the X-section pile group is much larger than that of the circular pile group. The axial force of X-section piles is smaller while the peak skin friction is larger than that of circular piles at the same depth. The skin friction of the core pile is the largest,followed by the side pile and the corner pile is the smallest when the load is relatively small;however, it is converse when the load is larger than 10 k N. Compared with piles in silica sand, the pile in coral sand has a lower bearing capacity, and the sand breakage leads to the steep drop failure of pile foundation. Moreover, pile positions under the raft have less effect on the load-share differences among corner, side and core piles in coral sand. This study provides a reference for the construction of pile foundations in coral sand.

Experimental and numerical investigation on the dynamic response of pile group in liquefying ground

The response of pile foundation in liquefable sand reinforced by densification techniques remains a very complex problem during strong earthquakes. A shake-table experiment was carried out to investigate the behavior of a reinforced concrete low-cap pile group embedded in this type of ground. In this study, a three-dimensional （3D） finite element （FE） analysis of the experiment was conducted. The computed response of the soil-pile system was in reasonable agreement with the experimental results, highlighting some key characteristics. Then, a parametric study was performed to explore the influence of pile spacing, pile stiffness （E/）, superstructure mass, sand permeability, and shaking characteristics of input motion on the behavior of the pile. The investigation demonstrated a stiffening behavior appearing in the liquefied medium- dense sand, and the pile group effect seemed negligible. Furthermore, the kinematic effect was closely connected with both EI and sand permeability. Nevertheless, the inertial effect was strongly influenced by the superstructure mass. Meanwhile, high frequency and large amplitude of the input motion could produced greater the pile＇s moments. It is estimated that this case study could further enhance the current understanding of the behavior of low-cap pile foundations in liquefied dense sand.

Numerical and test study on vertical vibration characteristics of pile group in slope soil topography

Topography effects on the vertical vibration responses of pile group are revealed though numerical analysis and model tests.First,a series of model tests with different topography of ground and bedrock are conducted.The results indicate that displacement amplitude of the pile head in sloping ground topography is larger than in horizontal ground.Differential displacement at various positions of the pile cap is observed in non-horizontal topography.Afterwards,a numerical algorithm is employed to further explore the essential response characteristics in group piles of different topography configurations,which has been verified by the test results.The lengths of the exposed and frictional segment,together with the thickness of the subsoil layer,are the dominant factors which cause non-axisymmetric vibration at the pile cap.

Simplified Calculation Method and 3D Numerical Analysis for Pile Group Under Uplift Loading

Pile foundations of ports, mooring systems for ocean surface or submerged platforms are subjected to amount of uplift loading, and prediction of the uplift capacity is one of the most important subjects in structure designs. The paper pertains to the development of a simplified theoretical method on prediction of the uplift capacity of pile group embedded in clay assuming a composite failure surface （inverted and tnmcated circular pyramidal and cylindrical sttrface）. Various pile and soil parameters such as the arrangement of pile group, pile spacing, length, diameter of the pile and the soil properties such as unit weight, angle of internal friction and the pile-soil interface friction angle, which have direct influence on the uplift capacity of the pile group, are incorporated in the analysis. A 3D numerical model is built by FLAC3D to analyze the pile group under uplift loading for comparison, and various effect factors, such as length to diameter ratio, pile spacing and pile numbers are considered. The predicted values of uplift capacity and failure surface of pile group with different length to diameter ratio, pile spacing and soil properties are then compared with numerical analysis results and tleld test results. The predictions are found to be in good agreement with numerical analysis and measured values, which validate the correctness of the developed method. It is also found that the uplift capacity is significantly influenced by the pile-soil friction coefficient, soil shear strength, etc.

Experimental study of vertical and batter pile groups in saturated sand using a centrifuge shaking table

To study the dynamic response of vertical and batter pile groups in saturated sand,dynamic tests of these pile groups in saturated sand were carried out using the ZJU400 geotechnical centrifuge at Zhejiang University.The following results were obtained.(1)As the motion intensity increased,the peak acceleration in soil layers at different depths significantly decreased,indicating that the soil stiffness was significantly reduced.(2)During the motion process,the instantaneous bending moment of the vertical and batter pile groups at different depths changed continuously,which had a strong relationship with the saturated sand liquefaction.In the process of sand liquefaction,the residual bending moment generated by the batter pile was more obvious than that of the vertical pile.(3)With the liquefaction of the saturated sand,the distribution of the maximum bending moment of the vertical pile group changed,and the bending moment near the pile cap of the vertical and batter pile groups was always large.(4)In certain cases,the horizontal acceleration and dynamic displacement of the vertical pile cap were amplified.When the motion intensity was large,residual displacement of the batter pile cap occurred.

Physical modeling of behaviors of cast-in-place concrete piled raft compared to free-standing pile group in sand

Similar to free-standing pile groups, piled raft foundations are conventionally designed in which the piles carry the total load of structure and the raft bearing capacity is not taken into account. Numerous studies indicated that this method is too conservative. Only when the pile cap is elevated from the ground level,the raft bearing contribution can be neglected. In a piled raft foundation, pileesoileraft interaction is complicated. Although several numerical studies have been carried out to analyze the behaviors of piled raft foundations, very few experimental studies are reported in the literature. The available laboratory studies mainly focused on steel piles. The present study aims to compare the behaviors of piled raft foundations with free-standing pile groups in sand, using laboratory physical models. Cast-in-place concrete piles and concrete raft are used for the tests. The tests are conducted on single pile, single pile in pile group, unpiled raft, free-standing pile group and piled raft foundation. We examine the effects of the number of piles, the pile installation method and the interaction between different components of foundation. The results indicate that the ultimate bearing capacity of the piled raft foundation is considerably higher than that of the free-standing pile group with the same number of piles. With installation of the single pile in the group, the pile bearing capacity and stiffness increase. Installation of the piles beneath the raft decreases the bearing capacity of the raft. When the raft bearing capacity is not included in the design process, the allowable bearing capacity of the piled raft is underestimated by more than 200%. This deviation intensifies with increasing spacing of the piles.

Behavior of Pile Group with Elevated Cap Subjected to Cyclic Lateral Loads

The pile group with elevated cap is widely used as foundation of offshore structures such as turbines, power transmission towers and bridge piers, and understanding its behavior under cyclic lateral loads induced by waves, tide water and winds, is of great importance to designing. A large-scale model test on 3×3 pile group with elevated cap subjected to cyclic lateral loads was performed in saturated silts. The preparation and implementation of the test is presented. Steel pipes with the outer diameter of 114 mm, thickness of 4.5 mm, and length of 6 m were employed as model piles. The pile group was cyclic loaded in a multi-stage sequence with the lateral displacement controlled. In addition, a single pile test was also conducted at the same site for comparison. The displacement of the pile cap, the internal forces of individual piles, and the horizontal stiffness of the pile group are presented and discussed in detail. The results indicate that the lateral cyclic loads have a greater impact on pile group than that on a single pile, and give rise to the significant plastic strain in the soil around piles. The lateral loads carried by each row of piles within the group would be redistributed with loading cycles. The lateral stiffness of the pile group decreases gradually with cycles and broadly presents three different degradation patterns in the test. Significant axial forces were measured out in some piles within the group, owing to the strong restraint provided by the cap, and finally lead to a large settlement of the pile group. These findings can be referred for foundation designing of offshore structures.

The Effect of the Propeller Jet on Pile Groups

The objective of this study is to determine the effect of jet propeller on the damage of berthing structures combined of armoured slope with pile groups. For this purpose, scour measurements were performed for four types berthing structures, which were armoured slope with tandem arrangements of piles for two and three piles and with side by side arrangements of piles for two and three piles. The effect of gap between piles on damage was investigated. The damage level induced by propeller jet between piles was determined. The gaps were 1, 2, 3, and 4 times the pile diameter. Three different values of Rpm （690, 820, and 950） were chosen for the tests. The diameter of circular piles is 40 mm. The slope ratio was 1/3 and the diameter of propeller was 10 cm.

Effects of riverbed scour on seismic performance of high-rise pile cap foundation

To explore the seismic performance of a high-rise pile cap foundation with riverbed scour, a finite element model for foundations is introduced in the OpenSees finite element framework. In the model, a fiber element is used to simulate the pile shaft, a nonlinear p-y element is used to simulate the soil-pile interaction, and the p-factor method is used to reflect the group effects. A global and local scour model is proposed, in which two parameters, the scour depth of the same row of piles and the difference in the scour depth of the upstream pile and the downstream pile, are included to study the influence of scour on the foundation. Several elasto-plastic static pushover analyses are performed on this finite element model. The analysis results indicate that the seismic capacity （or supply） of the foundation is in the worst condition when the predicted deepest global scout depth is reached, and the capacity becomes larger when the local scour depth is below the predicted deepest global scout depth. Therefore, to evaluate the seismic capacity of a foundation, only the predicted deepest global scout depth should be considered. The method used in this paper can be also applied to foundations with other soil types.

Design of bridges against large tectonic deformation

The engineering community has devoted much effort to understanding the response of soil-structure systems to seismic ground motions, but little attention to the effects of an outcropping fault offset. The 1999 earthquakes of Turkey and Taiwan, offering a variety of case histories of structural damage due to faulting, have （re）fueled the interest on the subject. This paper presents a methodology for design of bridges against tectonic deformation. The problem is decoupled in two analysis steps： the first （at the local level） deals with the response of a single pier and its foundation to fault rupture propagating through the soil, and the superstructure is modeled in a simplified manner; and the second （at the global level） investigates detailed models of the superstructure subjected to the support （differential） displacements of Step 1. A parametric study investigates typical models of viaduct and overpass bridges, founded on piles or caissons. Fixed-head piled foundations are shown to be rather vulnerable to faulting-dnduced deformation. End-bearing piles in particular are unable to survive bedrock offsets exceeding 10 cm. Floating piles perform better, and if combined with hinged pile-to-cap connections, they could survive much larger offsets. Soil resilience is beneficial in reducing pile distress. Caisson foundations are almost invariably successful. Statically-indeterminate superstructures are quite vulnerable, while statically-determinate are insensitive （allowing differential displacements and rotations without suffering any distress）. For large-span cantilever-construction bridges, where a statically determinate system is hardly an option, inserting resilient seismic isolation bearings is advantageous as long as ample seating can prevent the deck from falling off the supports. An actual application of the developed method is presented for a major bridge, demonstrating the feasibility of design against tectonic deformation.

Analysis of energy pile groups subjected to non-uniform thermal loadings

Sequentially coupled thermal-stress finite element analyses were performed to investigate the mechanical behaviors of an energy pile group subjected to non-uniform thermal loadings.The group effect was highlighted by comparing the thermo-mechanical responses with those of the single pile case.Due to the thermal interactions between piles,the group piles’temperatures were higher than that of the isolated single pile.If only part of the piles served as heat exchangers,i.e.,the pile group was thermal loaded unevenly,there were dif-ferential deformations between the heated and the non-heated piles.Due to the pile-raft-pile interaction,the axial forces of the piles chan-ged significantly.The location of the heated pile had an important influence on the thermally induced axial force,while the effect of the soil’s coefficient of thermal expansion was not significant.Inspired by the numerical result,a simplified method was proposed to capture the main characteristics of energy pile groups and to facilitate the design.The proposed method was developed in the framework of the traditional load transfer approach,and the pile-raft-pile interaction was included.By applying different temperature increments to dif-ferent piles,the non-uniform thermal loading was modeled.The proposed method was verified by comparing with the finite element anal-ysis results and the data collected from the literature.

Three-dimensional elasto-plastic finite element analysis of a soil-pilebridge interaction

The soil-pile-bridge interaction of super-large pile groups is a very complex issue for the design of deep pile group foundations. In this paper, the load distribution on the pile top of a super large bridge foundation and its influential factors are analyzed comprehensively using a three-dimensional elasto-plastic finite element method. The adopted model and its input parameters are firstly verified by comparing the numerical results with the measured data of static loading tests of a single pile. Numerical analysis is then performed to investigate the load distribution and the load-settlement characteristics of super-large pile groups, and the models are verified using centrifuge laboratory model testing data. The mechanism of the interaction between pile groups and soil under different conditions is explored.

Interaction of Building Frame with Pile Foundation

The study deals with physical modeling of a typical building frame resting on a pile group embedded in cohesive soil mass using complete three-dimensional finite element analysis. The elements of the superstructure frame and that of the pile foundation are discretized using twenty node isoparametric continuum elements. The interface between the pile and pile cap is idealized using sixteen node isoparametric surface elements. The more improved finite element mesh is used for modeling soil element as compared to the one used in the study reported in the literature. The soil elements are discretized using eight node, nine node and twelve node continuum elements. Both the elements of superstructure and substructure (i.e., foundation) including soil are assumed to remain in elastic state at all the time. The interaction analysis is carried out using sub-structure approach to attempt a parametric study. The effect of the parameter such as spacing between the piles in a group and diameter of pile is evaluated on the response of superstructure. The response includes the displacement at the top of the frame. The effect of the soil-structure interaction is observed to be significant for the type of foundation and soil considered in the present study.

WAVE CURRENT FORCES ON THE PILE GROUP OF BASE FOUNDATION FOR THE EAST SEA BRIDGE, CHINA

On the basis of the two structures of the bridge foundation designed for the East Sea Bridge, the wave current forces on four types of oblique piles, the pile group and the single piles at different positions in the pile group considering the effect of the super structures were experimentally investigated. The relationship between the wave current forces and the associated wave parameters, and the comparison of the wave current forces on the pile groups and the single piles were systematically analyzed. The group effectiveness and the reduction coefficient for the wave current forces on the group were examined for engineering design.

Finite element prediction on the response of non-uniformly arranged pile groups considering progressive failure of pile-soil system

A uniform arrangement of individual piles is commonly adopted in the conventional pile group foundation,and basin-shaped settlement is often observed in practice.Large differential settlement of pile groups will decrease the use-safety requirements of building,even cause the whole-building tilt or collapse.To reduce differential settlement among individual piles,non-uniformly arranged pile groups can be adopted.This paper presents a finite element analysis on the response of pile groups with different layouts of individual piles in pile groups.Using the userdefined subroutine FRIC as the secondary development platform,a softening model of skin friction and a hyperbolic model of end resistance are introduced into the contact pair calculation of ABAQUS software.As to the response analysis of a single pile,the reliability of the proposed secondary development method of ABAQUS software is verified using an iterative computer program.The reinforcing effects of individual piles is then analyzed using the present finite element analysis.Furthermore,the response of non-uniformly arranged pile groups,e.g.,individual piles with variable length and individual piles with variable diameter,is analyzed using the proposed numerical analysis method.Some suggestions on the layout of individual piles are proposed to reduce differential settlement and make full use of the bearing capacity of individual piles in pile groups for practical purposes.