A method to interpret fracture aperture of rock slope using adaptive shape and unmanned aerial vehicle multi-angle nap-of-the-object photogrammetry

The aperture of natural rock fractures significantly affects the deformation and strength properties of rock masses,as well as the hydrodynamic properties of fractured rock masses.The conventional measurement methods are inadequate for collecting data on high-steep rock slopes in complex mountainous regions.This study establishes a high-resolution three-dimensional model of a rock slope using unmanned aerial vehicle(UAV)multi-angle nap-of-the-object photogrammetry to obtain edge feature points of fractures.Fracture opening morphology is characterized using coordinate projection and transformation.Fracture central axis is determined using vertical measuring lines,allowing for the interpretation of aperture of adaptive fracture shape.The feasibility and reliability of the new method are verified at a construction site of a railway in southeast Tibet,China.The study shows that the fracture aperture has a significant interval effect and size effect.The optimal sampling length for fractures is approximately 0.5e1 m,and the optimal aperture interpretation results can be achieved when the measuring line spacing is 1%of the sampling length.Tensile fractures in the study area generally have larger apertures than shear fractures,and their tendency to increase with slope height is also greater than that of shear fractures.The aperture of tensile fractures is generally positively correlated with their trace length,while the correlation between the aperture of shear fractures and their trace length appears to be weak.Fractures of different orientations exhibit certain differences in their distribution of aperture,but generally follow the forms of normal,log-normal,and gamma distributions.This study provides essential data support for rock and slope stability evaluation,which is of significant practical importance.

Effect of stress-dependent microannulus aperture on well leakage

Debonding at the cement-casing interface is recognized as a principal failure mechanism leading to CO_(2) leakage in wells.This detachment gives rise to a microannulus,which notably possesses greater permeability than undamaged cement,undermining its sealing efficacy.Conventionally,the permeability of the microannulus is regarded as a uniform value throughout the well.However,fundamentally,a microannulus is one type of fracture,and its gap or aperture size is affected by the effective stress.In this work,we developed a unique experimental apparatus.This equipment facilitates the curing of cement inside a steel casing,the formation of a microannulus between the casing and the cement,and the investigation of the fluid flow dynamics along the microannulus under laboratory-replicated in situ conditions.The microannulus was formed by injecting fluid from one end of the setup,and receiving similar amount of fluid on the other end signified the development of the leakage channel.Additionally,strain gauges affixed to the casing’s external surface yielded key information on the microannulus’s opening and closure.We observed a noticeable decline in microannulus hydraulic aperture(or permeability)in relation to effective stress and an exponential equation fits their relationship.Our findings also indicate a distinct behavior when comparing liquid CO_(2) with water.Specifically,it is easier for liquid CO_(2) to create the microannulus.However,the hydraulic aperture range for this microannulus(0.7-6 mm)is considerably smaller than that created by water flow(2-17 mm).Finally,we integrated the stressdependent microannulus aperture size into the combined analysis of well mechanical integrity and well leakage.The outcomes consistently demonstrated that when factoring in the stress-dependent aperture sizes,the leakage rates are 3e5 times compared to a fixed aperture model.The traditional assumption of a constant aperture significantly underestimates fluid leakage risks.

Synthetic Aperture Positioning: A Review

Obtaining precise position of interested emitters passively has wide applications in both civilian and military fields.Different from traditional parameter measurement and direct position determination(DPD)method,recently a new passive localization method based on synthetic aper-ture technique,named synthetic aperture positioning(SAP),has been proposed.The method com-pensates for the nonlinear phase produced by relative motion between the moving platform and the emitter,achieving coherent summation of intercepted signals.The SAP can obtain high-resolution and high-precision localization results at a low signal-to-noise ratio.This paper summarizes the research progress of SAP,including localization principles,spaceborne applications,and application scope analysis.Besides,the possible future outlook of SAP is considered.

High-Precision DOA Estimation Method Based on Synthetic Aperture Technique

The existing direction-of-arrival(DOA)estimation methods only utilize the current received signals,which are susceptible to noise.In this paper,a method for DOA estimation based on a motion platform is proposed to achieve high-precision DOA estimation by utilizing past and present signals.The concept of synthetic aperture is introduced to construct a linear DOA estima-tion model.A DOA fine-tuning method based on the linear model is proposed to eliminate the lin-ear DOA variation,achieving a non-coherent accumulation of DOA estimations.Moreover,the baseband modulation and the phase modulation caused by the range history are compensated to achieve the coherent accumulation of all the DOA estimations.Simulation results show that the proposed method can significantly improve the DOA estimated accuracy at low signal-to-noise ratios(SNR).

Modulated-ISRJ rejection using online dictionary learning for synthetic aperture radar imagery

In electromagnetic countermeasures circumstances,synthetic aperture radar(SAR)imagery usually suffers from severe quality degradation from modulated interrupt sampling repeater jamming(MISRJ),which usually owes considerable coherence with the SAR transmission waveform together with periodical modulation patterns.This paper develops an MISRJ suppression algorithm for SAR imagery with online dictionary learning.In the algorithm,the jamming modulation temporal properties are exploited with extracting and sorting MISRJ slices using fast-time autocorrelation.Online dictionary learning is followed to separate real signals from jamming slices.Under the learned representation,time-varying MISRJs are suppressed effectively.Both simulated and real-measured SAR data are also used to confirm advantages in suppressing time-varying MISRJs over traditional methods.

Real-Time Fracture Aperture Identification Using Mud Loss Data and Solution for LCM Combination

Managing server lost circulation is a major challenge of drilling operation in naturally fractured formations and it causes much nonproductive rig time. When encountered with loss, the fracture aperture intersecting the wellbore is not well-identified in time, which has a significant impact on the decision of drilling operation and the undesired result of loss curing. Therefore, the onset of fracture is identified in a timely manner and evaluated comprehensively to formulate an appropriate strategy over time. However, the mud loss date, which is the primary source of information retrieved from the drilling process, was not properly used in real-time prediction of fracture aperture. This article provides a detailed mathematical study to discuss the mechanism of mud invasion in the near-wellbore region and prediction of fracture aperture. The fracture aperture can be calculated from mud-loss data by solving a cubic equation with input parameters given by the well radius, the overpressure ratio, and the maximum mud-loss volume. It permits the proper selection of loss-circulation material (LCM) with respect to particle size distribution and fiber usage. The case study illustrates the applicability of this methodology with a discussion on LCM particle distribution in different scenarios and the result demonstrates the outcome of inappropriate LCM usage and the advantages of the novel fiber-based LCM treatment.

Aperture shape optimization in intensity-modulated radiation therapy planning

The gradient element of the aperture gradient map is utilized directly to generate the aperture shape without modulation.This process can be likened to choosing the direction of negative gradient descent for the generic aperture shape optimiza-tion.The negative gradient descent direction is more suitable under local conditions and has a slow convergence rate.To overcome these limitations,this study introduced conjugate gradients into aperture shape optimization based on gradient modulation.First,the aperture gradient map of the current beam was obtained for the proposed aperture shape optimiza-tion method,and the gradients of the aperture gradient map were modulated using conjugate gradients to form a modulated gradient map.The aperture shape was generated based on the modulated gradient map.The proposed optimization method does not change the optimal solution of the original optimization problem,but changes the iterative search direction when generating the aperture shape.The performance of the proposed method was verified using cases of head and neck cancer,and prostate cancer.The optimization results indicate that the proposed optimization method better protects the organs at risk and rapidly reduces the objective function value by ensuring a similar dose distribution to the planning target volume.Compared to the contrasting methods,the normal tissue complication probability obtained by the proposed optimization method decreased by up to 4.61%,and the optimization time of the proposed method decreased by 5.26%on average for ten cancer cases.The effectiveness and acceleration of the proposed method were verified through comparative experiments.According to the comparative experiments,the results indicate that the proposed optimization method is more suitable for clinical applications.It is feasible for the aperture shape optimization involving the proposed method.

Development of short prototype of dual aperture quadrupole magnet for CEPC ring

Main quadrupole magnets are critical for the Circular Electron and Positron Collider(CEPC)and are specifically designed as dual aperture quadrupole(DAQ)magnets.However,the field crosstalk between the two apertures presents challenges.As the CEPC will work at four beam energies of Z,W,Higgs and ttbar mode,the DAQ magnets will operate at four field gradients spanning from 3.18 to 12.63 T/m.The first short quadrupole magnet prototype with the bore diameter of 76 mm and magnetic length of 1.0 m revealed the problems of large magnetic field harmonics and a magnetic center shift within the beam energy range.Accordingly,a compensation method was proposed in this work to solve the field crosstalk effect.By adjusting the gap height at the middle of the two apertures,the field harmonics and magnetic center shift are significantly reduced.After optimization,the short prototype was modified using a new scheme.The field simulations are validated from the magnetic measurement results.Further,the multipole field meets the requirements of the four beam energies.The detailed magnetic field optimization,field harmonics adjustment,and measurement results are presented herein.

Wide-spectrum optical synthetic aperture imaging via spatial intensity interferometry

High resolution imaging is achieved using increasingly larger apertures and successively shorter wavelengths.Optical aperture synthesis is an important high-resolution imaging technology used in astronomy.Conventional long baseline amplitude interferometry is susceptible to uncontrollable phase fluctuations,and the technical difficulty increases rapidly as the wavelength decreases.The intensity interferometry inspired by HBT experiment is essentially insensitive to phase fluctuations,but suffers from a narrow spectral bandwidth which results in a lack of effective photons.In this study,we propose optical synthetic aperture imaging based on spatial intensity interferometry.This not only realizes diffraction-limited optical aperture synthesis in a single shot,but also enables imaging with a wide spectral bandwidth,which greatly improves the optical energy efficiency of intensity interferometry.And this method is insensitive to the optical path difference between the sub-apertures.Simulations and experiments present optical aperture synthesis diffraction-limited imaging through spatial intensity interferometry in a 100 nm spectral width of visible light,whose maximum optical path difference between the sub-apertures reaches 69λ.This technique is expected to provide a solution for optical aperture synthesis over kilometer-long baselines at optical wavelengths.

Design and Research of Active Gravity Unloading Device for Large Aperture Optical Mirror

The large aperture optical mirror for space is processed and tested in the gravity environment on the ground. After entering space, gravity disappears due to the change of environment, and the mirror surface that has met the engineering requirements on the ground will change, seriously affecting the imaging quality. In order to eliminate the influence of gravity and to ensure the consistency of space and ground, gravity unloading must be performed. In order to meet the requirements of processing and testing for the large aperture space mirror in the state of vertical optical axis, a universal gravity unloading device was proposed. It was an active support and used air cylinders to provide accurate unloading force. First, the design flow of gravity unloading was introduced;then the detailed design of the mechanical structure and control system was given;then the performance parameters of the two types of cylinders were tested and compared, including the force-pressure relationship curve and the force-position relationship curve;finally, the experimental verification of the gravity unloading device was carried out;for a mirror with an aperture of ?2100 mm, the gravity unloading device was designed and a vertical detection optical path was built. The test results showed that by using this gravity unloading device, the actual processing surface accuracy of the mirror was better than 1/50λ-RMS, which met the application requirement of the optical system. Thus, it can be seen that using this gravity unloading device can effectively unload the gravity of the mirror and realize the accurate processing and measurement of the mirror surface. .

基于Aperture-based优化方式对鼻咽癌调强计划设计的探讨

目的:探讨和总结使用Aperture-based逆向计划完成鼻咽癌调强计划设计,所能达到的计划质量及计划设计经验。方法:使用医科达Precise计划系统对24例鼻咽癌进行调强计划设计,每个计划设计9个大野,PGTV、PCTV1和PCTV2的处方剂量分别为68￣70、60和54 Gy。结果:PGTV和PCTV1 95%以上体积达到处方剂量。脑干、脊髓、左右晶体和左右腮腺的最大量平均分别为55、41、6.1和34.8 Gy。结论:使用Aperture-based完成的根治性鼻咽癌调强计划,其计划质量符合临床要求,但对于套环型靶区,在PGTV与PCTV1之间的剂量梯度未能压缩得很好。

Ground Surface Ruptures and Near-Fault,Large-Scale Displacements Caused by the Wenchuan Ms8.0 Earthquake Derived from Pixel Offset Tracking on Synthetic Aperture Radar Images

The 12 May 2008 Wenchuan Ms8.0 earthquake produced surface displacements along the causative fault, the Yingxiu-Beichuan Fault, which are up to several meters near the fault. Because of the large gradient, satellite synthetic aperture radar （SAR） interferometric data are strongly incoherent; the usual SAR interferometry method does not allow such displacements to be measured. In the present study, we employed another approach, the technique based on pixel offset tracking, to solve this problem. The used image data of six tracks are from the Advanced Land Observing Satellite, Phased Array type L-band Synthetic Aperture Radar （ALOS/PALSAR） dataset of Japan. The results show that the entire surface rupture belt is 238 km long, extending almost linearly in a direction of 42°north-east. It is offset left laterally by a north-west-striking fault at Xiaoyudong, and turns at Gaochuan, where the rupture belt shifts toward the south by 5 km, largely keeping the original trend. In terms of the features of the rupture traces, the rupture belt can be divided into five sections and three types. Among them, the Beichuan-Chaping and Hongkou-Yingxiu sections are relatively complex, with large widths and variable traces along the trend. The Pingtong-Nanba and Qingping-Jingtang sections appear uniform, characterized by straight traces and small widths. West of Yingxiu, the rupture traces are not clear. North of the rupture belt, surface displacements are 2.95 m on average, mostly 2-3.5 m, with 7-9 m the maximum near Beichuan. South of the rupture belt, the average displacement is 1.75 m, dominated by 1-2 m, with 3-4 m at a few sites. In the north, the displacements in the radar line of sight are of subsidence, and in the south, they are uplifted, in accordance with a right-slip motion that moves the northern wall of the fault to the east, and the southern wall to the west, respectively. Along the Guanxian-Jiangyou Fault, there is a uplift zone in the radar line of sight, which is 66 km long, 1.5-6 km wide, and has vertical displacements of approximately 2 m, but no observable rupture traces.

Wave parameters retrieval for dual-polarization C-band synthetic aperture radar using a theoretical-based algorithm under cyclonic conditions

Theoretical-based ocean wave retrieval algorithms are applied by inverting a synthetic aperture radar(SAR)intensity spectrum into a wave spectrum, that has been developed based on a SAR wave mapping mechanism. In our previous studies, it was shown that the wave retrieval algorithm, named the parameterized first-guess spectrum method(PFSM), works for C-band and X-band SAR at low to moderate sea states. In this work, we investigate the performance of the PFSM algorithm when it is applied for dual-polarization c-band sentinel-1(S-1) SAR acquired in extra wide-swath(EW) and interferometric wide-swath(IW) mode under cyclonic conditions.Strong winds are retrieved from six vertical-horizontal(VH) polarization S-1 SAR images using the c-band crosspolarization coupled-parameters ocean(C-3 PO) model and then wave parameters are obtained from the image at the vertical-vertical(VV) polarization channel. significant wave height(SWH) and mean wave period(MWP) are compared with simulations from the WAVEWATCH-III(WW3) model. The validation shows a 0.69 m root mean square error(RMSE) of SWH with a –0.01 m bias and a 0.62 s RMSE of MWP with a –0.17 s bias. Although the PFSM algorithm relies on a good quality SAR spectrum, this study confirms the applicability for wave retrieval from an S-1 SAR image. Moreover, it is found that the retrieved results have less accuracy on the right sector of cyclone eyes where swell directly affects strong wind-sea, while the PFSM algorithm works well on the left and rear sectors of cyclone eyes where the interaction of wind-sea and swell is relatively poor.

Method of moving target detection based on sub-image cancellation for single-antenna airborne synthetic aperture radar

The method of moving target detection based on subimage cancellation for single-antenna airborne SAR is presented. First the subimage is obtained through frequency processing is pointed out. The imaging difference of a stationary objects and moving object in the subimage based on the frequency division is analyzed from the fundamental principle. Then the developed method combines the shear averaging algorithm to focus on the moving target in the subimage, after the clutter suppression and the focusing position in each subimage is obtained. Next the observation model and the relative movement of the moving targets between the subimages estimate the moving targets. The theoretical analysis and simulation results demonstrate that the method is effective and can not only detect the moving targets, but also estimate their motion parameters precisely.

Motion estimation in wide band synthetic aperture sonar based on the raw echo data using the method of displaced phase center antenna

Phase errors in synthetic aperture sonar (SAS) imaging must be reduced to less than one eighth of a wavelength so as to avoid image destruction. Most of the phase errors occur as a result of platform motion errors, for example, sway yaw and surge that are the most important error sources. The phase error of a wide band synthetic aperture sonar is modeled and solutions to sway yaw and surge motion estimation based on the raw sonar echo data with a Displaced Phase Center Antenna (DPCA) method are proposed and their implementations are detailed in this paper. It is shown that the sway estimates can be obtained from the correlation lag and phase difference between the returns at coincident phase centers. An estimate of yaw is also possible if such a technique is applied to more than one overlapping phase center positions. Surge estimates can be obtained by identifying pairs of phase centers with a maximum correlation coefficient. The method works only if the platform velocity is low enough such that a number of phase centers from adjacent pings overlap.

Rapid detection to long ship wake in synthetic aperture radar satellite imagery

The maritime administrative department employs synthetic aperture radar (SAR) satellite remote sensing technology to obtain evidence of illegal discharge of ships. If the ship is discharged during navigation, it forms a long dark wake on the SAR image due to the suppression of the Bragg wave by the oil fi lm. This study investigates key techniques for rapid detection of long ship wakes, thereby providing law enforcement agencies with candidate ships for possible discharge. This paper presents a rapid long ship wake detection method that uses satellite imaging parameters and the axial direction of the ship in images to determine the potential detection area of the wake. Then, the threshold of long ship wake detection is determined using statistical analysis, the area is binarized, and isolated points are removed using a morphological filter operator. The method was tested with ENVISAT Synthetic Aperture Radar and GF-3 SAR data, and results showed that the method was eff ective, and the overall accuracy of the decision reaches 71%. We present two innovations;one is a method that draws a Doppler shift curve, and uses the SAR imaging parameters to determine the detection area of the long wake to achieve rapid detection and reduce the image detection area. The other is where a classical linear fitting method is used to quickly and accurately determine whether the detected dark area is a long ship wake and realizes the twisted long ship wake detection caused by the sea surface flow field, which is otherwise diffi cult to detect by the traditional Radon and Hough transform methods. This method has good suppression performance for the dark spot false alarm formed by low speed wind region or upward flow. The method is developed for maritime ship monitoring system and will promote the operational application of maritime ship monitoring system.

Coastal wind field retrieval from polarimetric synthetic aperture radar

Coastal winds are strongly influenced by topology and discontinuity between land and sea surfaces. Wind assessment from remote sensing in such a complex area remains a challenge. Space-borne scatterometer does not provide any information about the coastal wind field, as the coarse spatial resolution hampers the radar backscattering. Synthetic aperture radar （SAR） with a high spatial resolution and all-weather observation abilities has become one of the most important tools for ocean wind retrieval, especially in the coastal area. Conventional methods of wind field retrieval from SAR, however, require wind direction as initial information, such as the wind direction from numerical weather prediction models （NWP）, which may not match the time of SAR image acquiring. Fortunately, the polarimetric observations of SAR enable independent wind retrieval from SAR images alone. In order to accurately measure coastal wind fields, this paper proposes a new method of using co-polarization backscattering coefficients from polarimetric SAR observations up to polarimetric correlation backscattering coefficients, which are acquired from the conjugate product of co-polarization backscatter and cross-polarization backscatter. Co-polarization backscattering coefficients and polarimetric correlation backscattering coefficients are obtained form Radarsat-2 single-look complex （SLC） data.The maximum likelihood estimation is used to gain the initial results followed by the coarse spatial filtering and fine spatial filtering. Wind direction accuracy of the final inversion results is 10.67 with a wind speed accuracy of 0.32 m/s. Unlike previous methods, the methods described in this article utilize the SAR data itself to obtain the wind vectors and do not need external wind directional information. High spatial resolution and high accuracy are the most important features of the method described herein since the use of full polarimetric observations contains more information about the space measured.This article is a useful addition to the work of independent SAR wind retrieval. The experimental results herein show that it is feasible to employ the co-polarimetric backscattering coefficients and the polarimetric correlation backscattering coefficients for coastal wind field retrieval.

Design of synthetic aperture radar low-intercept radio frequency stealth

Not confined to a certain point,such as waveform,this paper systematically studies the low-intercept radio frequency(RF)stealth design of synthetic aperture radar(SAR)from the system level.The study is carried out from two levels.In the first level,the maximum low-intercept range equation of the conventional SAR system is deduced firstly,and then the maximum low-intercept range equation of the multiple-input multiple-output SAR system is deduced.In the second level,the waveform design and imaging method of the low-intercept RF SAR system are given and verified by simulation.Finally,the main technical characteristics of the lowintercept RF stealth SAR system are given to guide the design of low-intercept RF stealth SAR system.

A synthetic aperture radar sea surface distribution estimation by n-order Bézier curve and its application in ship detection

To dates,most ship detection approaches for single-pol synthetic aperture radar（SAR） imagery try to ensure a constant false-alarm rate（CFAR）.A high performance ship detector relies on two key components：an accurate estimation to a sea surface distribution and a fine designed CFAR algorithm.First,a novel nonparametric sea surface distribution estimation method is developed based on n-order Bézier curve.To estimate the sea surface distribution using n-order Bézier curve,an explicit analytical solution is derived based on a least square optimization,and the optimal selection also is presented to two essential parameters,the order n of Bézier curve and the number m of sample points.Next,to validate the ship detection performance of the estimated sea surface distribution,the estimated sea surface distribution by n-order Bézier curve is combined with a cell averaging CFAR（CA-CFAR）.To eliminate the possible interfering ship targets in background window,an improved automatic censoring method is applied.Comprehensive experiments prove that in terms of sea surface estimation performance,the proposed method is as good as a traditional nonparametric Parzen window kernel method,and in most cases,outperforms two widely used parametric methods,K and G0 models.In terms of computation speed,a major advantage of the proposed estimation method is the time consuming only depended on the number m of sample points while independent of imagery size,which makes it can achieve a significant speed improvement to the Parzen window kernel method,and in some cases,it is even faster than two parametric methods.In terms of ship detection performance,the experiments show that the ship detector which constructed by the proposed sea surface distribution model and the given CA-CFAR algorithm has wide adaptability to different SAR sensors,resolutions and sea surface homogeneities and obtains a leading performance on the test dataset.