Current progress of research on heat -resistant Mg alloys: A review

With the increasing attention received by lightweight metals,numerous essential fields have increased requirements for mag-nesium(Mg)alloys with good room-temperature and high-temperature mechanical properties.However,the high-temperature mechanic-al properties of commonly used commercial Mg alloys,such as AZ91D,deteriorate considerably with increasing temperatures.Over the past several decades,extensive efforts have been devoted to developing heat-resistant Mg alloys.These approaches either inhibit the gen-eration of thermally unstable phases or promote the formation of thermally stable precipitates/phases in matrices through solid solution or precipitation strengthening.In this review,numerous studies are systematically introduced and discussed.Different alloy systems,includ-ing those based on Mg–Al,Mg–Zn,and Mg–rare earth,are carefully classified and compared to reveal their mechanical properties and strengthening mechanisms.The emphasis,limitations,and future prospects of these heat-resistant Mg alloys are also pointed out and dis-cussed to develop heat-resistant Mg alloys and broaden their potential application areas in the future.

Effect of Mn addition on microstructure and mechanical properties of GX40CrNiSi25-12 austenitic heat resistant steel

Three types of steels were designed on the basis of GX40CrNiSi25-12 austenitic heat resistant steel by adding different Mn contents(2wt.%,6wt.%,and 12wt.%).Thermodynamic calculation,microstructure characterization and mechanical property tests were conducted to investigate the effect of Mn addition on the microstructure and mechanical properties of the austenitic heat resistant steel.Results show that the matrix structure in all the three types of steels at room temperature is completely austenite.Carbides NbC and M_(23)C_(6)precipitate at grain boundaries of austenite matrix.With the increase of Mn content,the number of carbides increases and their distribution becomes more uniform.With the Mn content increases from 1.99%to 12.06%,the ultimate tensile strength,yield strength and elongation increase by 14.6%,8.0%and 46.3%,respectively.The improvement of the mechanical properties of austenitic steels can be explained by utilizing classic theories of alloy strengthening,including solid solution strengthening,precipitation strengthening,and grain refinement.The increase in alloy strength can be attributed to solid solution strengthening and precipitation strengthening caused by the addition of Mn.The improvement of the plasticity of austenitic steels can be explained from two aspects:grain refinement and homogenization of precipitated phases.

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.

LONG-TERM CREEP AND RUPTURE PROPERTIES OF HEATRESISTING STEELS AND ALLOYS

The present status of NRIM Creep Data Sheet Project and the recent activities of long-term creep and rupture studies on heat resisting steels are described. The project has been continued to produce long-term data such as 100 000h-creep rupture strength for 47 kinds of principal heat resisting steels and alloys, including welded joints. The long-term creep deformation behavior and microstructural evolution during creep have been shown to be complicated.

Wire arc additive manufacturing of a heat-resistant Al-Cu-Ag-Sc alloy:microstructures and high-temperature mechanical properties

With a high energy efficiency,low geometric limitation,and low cracking susceptivity to cracks,wire arc additive manufacturing(WAAM)has become an ideal substitute for casting in the manufacturing of load-bearing high strength aluminum components in aerospace industry.Recently,in scientific researches,the room temperature mechanical performance of additive manufactured high strength aluminum alloys has been continuously broken through,and proves these alloys can achieve comparable or even higher properties than the forged counterpart.Since the aluminum components for aerospace usage experience high-low temperature cycling due to the absence of atmosphere protection,the high temperature performances of additive manufactured high strength aluminum alloys are also important.However,few research focuses on that.A special 2319Ag Sc with 0.4 wt.%Ag and 0.2 wt.%Sc addition designed for high temperature application is deposited successfully via cold metal transfer(CMT)based on WAAM.The microstructures and high temperature tensile properties are investigated.The results show that the as-deposited 2319Ag Sc alloy presents an alternate distribution of columnar grains and equiaxed grains with no significant textures.Main second phases are Al_(2)Cu and Al3Sc,while co-growth of Al_(2)Cu and bulk Al_(3)Sc is found on the grain boundary.During manufacturing,nanoscale Al_(2)Cu can precipitate out from the matrix.Ag and Mg form nano-scaleΩphase on the Al_(2)Cu precipitates.At 260℃,average yield strengths in the horizontal direction and vertical direction are 87 MPa±2 MPa,87 MPa±4 MPa,while average ultimate tensile strengths are 140 MPa±7 MPa,141 MPa±11 MPa,and average elongations are 11.0%±2.5%,13.5%±3.0%.Anisotropy in different directions is weak.

Precipitation behavior and martensite lath coarsening during tempering of T/P92 ferritic heat-resistant steel

Tempering is an important process for T/P92 ferritic heat-resistant steel from the viewpoint of microstructure control, as it facili- tates the formation of final tempered martensite under serving conditions. In this study, we have gained deeper insights on the mechanism underlying the microstructural evolution during tempering treatment, including the precipitation of carbides and the coarsening of martensite laths, as systematically analyzed by optical microscopy, transmission electron microscopy, and high-resolution transmission electron mi- croscopy. The chemical composition of the precipitates was analyzed using energy dispersive X-ray spectroscopy. Results indicate the for- mation of M3C （cementite） precipitates under normalized conditions. However, they tend to dissolve within a short time of tempering, owing to their low thermal stability. This phenomenon was substantiated by X-ray diffraction analysis. Besides, we could observe the precipitation of fine carbonitrides （MX） along the dislocations. The mechanism of carbon diffusion controlled growth of M23C6 can be expressed by the Zener＇s equation. The movement of Y-junctions was determined to be the fundamental mechanism underlying the martensite lath coarsening process. Vickers hardness was estimated to determine their mechanical properties. Based on the comprehensive analysis of both the micro- structural evolution and hardness variation, the process of tempering can be separated into three steps.

Improvements of heat resistance and adhesive property of condensed poly-nuclear aromatic resin via epoxy resin modification

A bisphenol epoxy resin was used as modifier to increase the heat resistance of condensed poly-nuclear aromatic （COPNA） resin. The basic properties of COPNA resin and modified resin were characterized by Fourier transform infrared spectroscopy （FT-IR）, nuclear magnetic resonance spectroscopy （1H-NMR）, vapor pressure osmometry （VPO） and elemental analysis （EA）. Average structural parameters of resins were calculated by the improved Brown-Ladner method, and heat resistance of resins was tested by thermogravimetric analysis （TGA）. The chemical structure, mechanical properties and heat resistivity of the resin/graphite composites prepared with different resins were compared. The results show that the adhesive property and heat resistance of COPNA resin can be remarkably improved by addition of 5 wt.% epoxy resin. The reason is that the reactions between epoxy groups of epoxy resin and hydroxyl groups of COPNA resin improve the heat resistance and adhesive property of COPNA resin. Electric motor brushes with good mechanical properties and low electrical resistivity were successfully prepared by using the modified resin as binder.

Coarsening behavior of MX carbonitrides in type 347H heat-resistant austenitic steel during thermal aging

In this work, the growth kinetics of MX （M - metal, X - C/N） nanoprecipitates in type 347H austenitic steel was systematically studied. To investigate the coarsening behavior and the growth mechanism of MX carbonitrides during long-term aging, experiments were performed at 700, 800, 850, and 900℃ for different periods （1, 24, 70, and 100 h）. The precipitation behavior of carbonitrides in specimens subjected to various aging conditions was explored using carbon replicas and transmission electron microscopy （TEM） observations. The corresponding sizes ofMX carbonitrides were measured. The results demonstrates that MX carbonitrides precipitate in type 347H austenitic steel as Nb（C,N）. The coarsening rate constant is time-independent; however, an increase in aging temperature results in an increase in coarsening rate of Nb（C,N）. The coarsening process was analyzed according to the calculated diffusion activation energy of Nb（C,N）. When the aging temperature was 800-900℃, the mean activation energy was 294 kJ·mol -1, and the coarsening behavior was controlled primarily by the diffusion of Nb atoms.

Microstructural Evolution of 2.25Cr-1.6W-V-Nb Heat Resistant Steel during Creep

2.25Cr-1.6W-V-Nb developed in Japan, is a low alloy heat resistant steel with good comprehensive properties. Influence of long term creep at elevated temperature on the structure of 2.25Cr-1.6W-V-Nb steel was studied in this paper, and the micromechanism of creep strength degradation was elucidated, too. Both TEM observation and thermodynamic calculation reveal that during creep the transformation occurs from M7C3 and M23C6 to M6C, which can be cavity nucleation sites. Besides, creep at 600癈 also leads to the decrease of dislocation density, the coarsening and coalescence of M23C6, the nucleation of cavities and development of cracks. The strength decrease of 2.25Cr-1.6W-V-Nb steel after long term creep is related to the decrease of dislocation hardening, precipitation hardening, solution hardening, the nucleation of cavities and development of cracks.

Micro-analysis of high-temperature oxidation-resistance of a new kind of heat-resistant grid plate in grate-kiln

To further improve the oxidation-resistance of materials and reduce the cost of grid plates in grate-kiln, a new kind of heat-resistant grid plate was developed. The microstructure of this grid plate with a life more than 18 months was studied by XRD, SEM and EDS techniques. The results show that high hardness, high intensity and good impact property make the new kind of heat-resistant grid plate and its oxide film have a higher resistance to deformation and abrasion at 900-1000℃ Besides, small grain size is beneficial to form a complete protective oxide film. The oxide film composed of SiO2 layer, Cr2O3 layer and Fe2O3 layer is rather thin and bonds closely with the backing. The forming of the chemical stable nickel-rich layer increases the density of Cr2O3 layer.

Formation Mechanism and Existing Form of Sb in Heat Resistance Mg-Gd-Y-Sb Alloy

The existing form and reaction mechanism of Sb in heat resistane Mg-Gd-Y-Sb rare earth magnesium alloy were investigated by inductive coupled plasma emission spectroscopy(ICP),scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and X-ray diffraction(XRD).It is found that Sb tends to form high melting point intermetallics with rare earth elements of Gd and Y.The existing form of Sb is determined to be GdSb and SbY,respectively,which has high melting point(GdSb:2142℃/SbY:1782℃).Meanwhile,the first principle calculation and electronegativity difference calculation were performed to further understand the reaction mechanism.Therefore,the forming heat and binding energy were calculated.The experimental results show that the binding tendency of Sb element to Gd and Y is much stronger than that of it with other elements in this alloy,which results in the formation of high melting point of Gd-Sb and Y-Sb intermetallics,and finally leads to the high temperature resistant further improvement of the Mg-Gd-Y magnesium alloy.

Heat Resistance of TiN Coated HSS Tools

The cutting friction, cutting deformation, producing heat, conducting heat, temperature field of TiN coated HSS tools in the cutting process are discussed profoundly. In order to make clear the heat property of TiN coated tools, from the micromechanism angle, the relationship of the heat property and the crystal structure of TiN compound is analyzed, and the regularity of TiN compound crystal structure changing with temperature rising is sought. The difference of the wear resistance and heat resistance of TiN coated tools deposited by c1 and c2 depositing techniques is proved by tests. The conclusions will offer the theoretical basis for correct design of geometrical parameters of TiN coated tools, rational selection of cutting regimes and optimization of the depositing technique.

EFFECT OF HEAT TREATMENT ON INTERMEDIATE TEMPERATURE STRESS RUPTURE PROPERTIES OF ALLOY K403

The standard heat treatment of cast nickel base superalloy K403 is the solid solution treatment of 1210℃/4h, air cooling. It is very difficult to meet the requirements of Aviation Standard HB5155, in which the stress rupture life at 750℃ and 645MPa is longer than 50h. The results showed that the intermediate temperature stress rupture properties impaired by treatment of 1210℃/4h were due to precipitation of too small γ′ phase(<0.2μm) in grains and absence of the secondary carbides at grain boundaries. Microstructure containing the intergranular M6C carbides with envelope of γ′ and the residual coarse γ′ was obtained by means of 1180℃/4h treatment, therefore the stress rupture life was obviously increased to meet the demand of HB5155. The effect of γ′ size was also discussed from the view point of deformation mechanism in this paper.

High-temperature oxidation behavior of heat resistant stainless steel 1.4828

The kinetic curves of the high-temperature oxidation of austenitic heat resistant stainless steel 1. 4828 at 1 050 ℃ were measured using a weighing method. It is shown that the oxidation curves at 1 050 ℃ followed the parabolic line law, and after 250 h of oxidation, the mass gain was about 80 g/m2. The surface morphology and structure of the oxide layers were studied by scanning electron microscopy and X-ray diffraction. A complicated oxide layer obtained at 1 050 ℃ was mainly composed, from inner to outer, of （FeSi） 3 04, Cr2 03, Fe2 03, and spinel oxides FeCr204 and NiMn204.

Effect of aging temperature on the microstructures and mechanical properties of ZG12Cr9Mo1Co1NiVNbNB ferritic heat-resistant steel

The effect of aging on the mechanical properties and microstructures of a new ZG12Cr9 MolColNiVNbNB ferritic heat resistant steel was investigated in this work to satisfy the high steam parameters of the ultra-supercritical power plant.The results show that the main precipitates during aging are Fe（Cr,Mo）23C6,V（Nb）C,and（Fe2Mo） Laves in the steel.The amounts of the precipitated phases increase during aging,and correspondingly,the morphologies of phases are similar to be round.Fe（Cr,Mo）23C6 appears along boundaries and grows with increasing temperature.In addition,it is revealed that the martensitic laths are coarsened and eventually happen to be polygonization.The hardness and strength decrease gradually,whereas the plasticity of the steel increases.What＇s more,the hardness of this steel after creep is similar to that of other 9%-12%Cr ferritic steels.Thus,ZG12Cr9 MolColNiVNbNB can be used in the project.

Characterization of precipitates in 9%Cr heat resistant steel

Precipitation strengthening as well as solution strengthening is key mechanism for heat resistant steels.It is very important to characterize the precipitates in 9%Cr ferrite heat resistant steels,especially to show the nanometer-sized particles.By transmission electronic microscope attached with an energy dispersive spectrometer as well as optical microscope,scanning electronic microscope,the microstructure and chemical composition of precipitates in a 9%Cr heat resistant steel after different heat treatments were investigated.It was found that the microstructure of normalized sample was martensite with fine NbC and Fe_3C.The microstructure of tempered sample is tempered martensite,and there mainly were two types of precipitates,M_(23)C_6 with the size range of 50 - 300 nm and MX with the size of 10 - 100 nm.Superfine M_(23)C_6 precipitated preferably on prior austenitic grain boundaries and martensitic lath boundaries,while nanometer-sized MX precipitates were distributed randomly. After short-term creep,Laves phase formed along grain boundaries of the 9%Cr steel,and M_(23) C_6 and MX precipitates were found to become coarser.More information about precipitates in the 9%Cr steel had been exhibited by atomic force microscopy.Thereby,distribution,size and shape of the precipitates as well as their compositions and structures were revealed.

A Study on Heat Resistance and Initial Characterization of Protease Inhibitors in Porcine Colostrum

Porcine colostrum was separated into the acid soluble fraction (SF) and casein fraction (CF) by acidifying followed by centrifuge. SF was further separated by liquid chromatography and anisotropic membrane filtration. Capacities of the SF or CF of porcine colostrum, to inhibit trypsin and chymotrypsin activity and to inhibit the epidermal growth factor (EGF) degradation in pig small intestinal contents, were determined under different heat treatments. The study showed that trypsin inhibitors in porcine colostrum survived heat treatments of 100℃ water bath for up to 10 min, but exposure to boiling water bath for 30 min significantly decreased the inhibitory activity. Compared with the trypsin inhibitors, the chymotrypsin inhibitors were more heat sensitive. SF was more heat sensitive than CF. Separation of the SF of porcine colostrum by liquid chromatography and anisotropic membrane filtration revealed that the porcine colostrum protease inhibitors, those had the capacity to inhibit the trypsin chymotrypsin activity and enhanced the stability of EGF in the gastrointestinal(GI) lumen of weaned pigs, existed mainly in SF, milk derived, were a group of heat labile small proteins with molecular weight of 10 00050 000.

THERMAL ANALYSIS STUDY OF Fe-Cr-Mn HEAT RESISTANT ALLOY

Thermal analysis has been adopted to determine the liquidus and eutectic temperature of Fe-20%Cr-Mn alloy over range of Mn and C contents.Using regression analysis,the par- tial quasi-binary phase diagrams of Fe-Mn alloy(solidification range)have been con- structed.And the effect of Mn content on liquidus and eutectic temperature was discussed.

R&D on Resistive Heat Exchangers for HTS High Rated Current Leads

The HTS current leads of superconducting magnets for large scale fusion devices and high energy particle colliders can reduce the power consumption for cooling by 2/3 compared with conventional leads. The resistive sections of high-rated current leads are usually made of a heat exchanger cooled by gas flow. The supply of the cooling mass flow incurs more than 90% of the cooling cost for the HTS leads. The mass flow rate requirement depends not only on the length and material of the resistive heat exchanger, but also on the heat transfer coefficient and HEX surface, the joint resistance at the cold end of a sheet-stack HEX with a larger specific presented in the paper. The test results of efficiency can be achieved. and its cooling approach. The design and operation surface and a much smaller hydraulic diameter are an HTS lead optimized for 8 kA show that a 98.4%

Optimization of fin geometry in heat convection with entransy theory

The entransy theory developed in recent years is used to optimize the aspect ratio of a plate fin in heat convection.Based on a two-dimensional model,the theoretical analysis shows that the minimum thermal resistance defined with the concept of entransy dissipation corresponds to the maximum heat transfer rate when the temperature of the heating surface is fixed.On the other hand,when the heat flux of the heating surface is fixed,the minimum thermal resistance corresponds to the minimum average temperature of the heating surface.The entropy optimization is also given for the heat transfer processes.It is observed that the minimum entropy generation,the minimum entropy generation number,and the minimum revised entropy generation number do not always correspond to the best heat transfer performance.In addition,the influence factors on the optimized aspect ratio of the plate fin are also discussed.The optimized ratio decreases with the enhancement of heat convection,while it increases with fin thermal conductivity increasing.