Optimal synthesis of heat-integrated distillation configurations using the two-column superstructure

In the realm of the synthesis of heat-integrated distillation configurations,the conventional approach for exploring more heat integration possibilities typically entails the splitting of a single column into a twocolumn configuration.However,this approach frequently necessitates tedious enumeration procedures,resulting in a considerable computational burden.To surmount this formidable challenge,the present study introduces an innovative remedy:The proposition of a superstructure that encompasses both single-column and multiple two-column configurations.Additionally,a simultaneous optimization algorithm is applied to optimize both the process parameters and heat integration structures of the twocolumn configurations.The effectiveness of this approach is demonstrated through a case study focusing on industrial organosilicon separation.The results underscore that the superstructure methodology not only substantially mitigates computational time compared to exhaustive enumeration but also furnishes solutions that exhibit comparable performance.

Effects of the Water-Cement Ratio and the Molding Temperature on the Hydration Heat of Cement

The effects of the water-cement ratio and the molding temperature on the hydration heat of cement were investigated with semi-adiabatic calorimetry.The specimens were prepared with water-cement ratios of 0.31,0.38,and 0.45,and the molding temperature was specified at 10 and 20℃.The experimental results show that,as the water-binder ratio increases,the value of the second temperature peak on the temperature curve of the cement paste decreases,and the age at which the peak appears is delayed.The higher the water-cement ratio,the higher the hydration heat release in the early period of cement hydration,but this trend reverses in the late period.There are intersection points of the total hydration heat curve of the cement pastes under the influence of the water-cement ratio,and this law can be observed at both molding temperatures.With the increase in the molding temperature,the age of the second temperature peak on the temperature curve of the cement paste will advance,but the temperature peak will decrease.The higher the molding temperature,the earlier the acceleration period of the cement hydration began,and the larger the hydration heat of the cement in the early stage,but the smaller the total heat in the late period.A subsection function calculation model of the hydration heat,which was based on the existing models,was proposed in order to predict the heat of the hydration of the concrete.

Numerical Study on the Impacts of Hydrometeor Processes on the“21·7”Extreme Rainfall in Zhengzhou Area of China

The impacts of hydrometeor-related processes on the development and evolution of the“21·7”extremely heavy rainfall in Zhengzhou were investigated using WRF simulations.Surface precipitation was determined by the hydrometeor microphysical processes(all microphysical source sink terms of hydrometeors)and macrophysical processes(local change and flux convergence of hydrometeors).The contribution of hydrometeor macrophysical processes was commonly less than 10%,but could reach 30%–50%in the early stage of precipitation,which was largely dependent on the size of the study area.The macrophysical processes of liquid-phase hydrometeors always presented a promotional effect on rainfall,while the ice-phase hydrometeors played a negative role in the middle and later stages of precipitation.The distributions of microphysical latent heat corresponded well with those of buoyancy and vertical velocity(tendency),indicating that the phase-change heating was the major driver for convective development.Reasonable diagnostic buoyancy was obtained by choosing an area close to the convective size for getting the reference state of air.In addition,a new dynamic equilibrium involving hydrometeors with a tilted airflow was formed during the heavy precipitation period(updraft was not the strongest).The heaviest instantaneous precipitation was mainly produced by the warm-rain processes.Sensitivity experiments further pointed out that the uncertainty of latent heat parameterization(±20%)did not significantly affect the convective rainfall.While when the phase-change heating only altered the temperature tendency,its impact on precipitation was remarkable.The results of this study help to deepen our understanding of heavy rainfall mechanisms from the perspective of hydrometeor processes.

Combining reinforcement learning with mathematical programming:An approach for optimal design of heat exchanger networks

Heat integration is important for energy-saving in the process industry.It is linked to the persistently challenging task of optimal design of heat exchanger networks(HEN).Due to the inherent highly nonconvex nonlinear and combinatorial nature of the HEN problem,it is not easy to find solutions of high quality for large-scale problems.The reinforcement learning(RL)method,which learns strategies through ongoing exploration and exploitation,reveals advantages in such area.However,due to the complexity of the HEN design problem,the RL method for HEN should be dedicated and designed.A hybrid strategy combining RL with mathematical programming is proposed to take better advantage of both methods.An insightful state representation of the HEN structure as well as a customized reward function is introduced.A Q-learning algorithm is applied to update the HEN structure using theε-greedy strategy.Better results are obtained from three literature cases of different scales.

Effect of Low pH on Forming Process of Desulfurization Gypsum Composite Boards Strengthened by Melamine-formaldehyde Resin

Through exploring the effects of low pH on the composite system of desulfurization gypsum(DG)enhanced by melamine-formaldehyde resin(MF),it is found that the inducing of sulfate-ion,in contrast to chloride and oxalate ions,favors the longitudinal growth of the crystalline form of the hydration product,which was relatively simple and had the highest length to width(L/D)ratio.At the same time,MF can also improve L/D ratio of gypsum hydration products,which favors the formation of hydrated whiskers.Finally,in a composite system composed of hemihydrate gypsum,MF,and glass fibers,when dilute sulfuric acid was used to regulate pH=3-4,the tight binding formed among the components of the composite system compared to pH=5-6.The hydration product of gypsum adheres tightly to glass fiber surface and produces a good cross-linking and binding effect with MF.The flexural strength,compressive strength,elastic modulus,and water absorption of the desulphurized gypsum composite board is 22.7 MPa,39.8 MPa,5608 MPa,and 1.8%,respectively.

Finite-Time Thermodynamic Simulation of Circulating Direct Condensation Heat Recovery on Chillers

A time series model is used in this paper to describe the progress of circulating direct condensation heat recovery of the compound condensing process (CCP) which is made of two water cooling condensing processes in series for a centrifugal chiller in the paper. A finite-time thermodynamics method is used to set up the time series simulation model. As a result, an upper bound of recoverable condensation heat for the compound condensing process is obtained which is in good agreement with experimental result. And the result is valuable and useful to optimization design of condensing heat recovery.

Cleanliness of Ti-bearing Al-killed ultra-low-carbon steel during different heating processes

During the production of Ti-bearing Al-killed ultra-low-carbon(ULC) steel, two different heating processes were used when the converter tapping temperature or the molten steel temperature in the Ruhrstahl–Heraeus(RH) process was low: heating by Al addition during the RH decarburization process and final deoxidation at the end of the RH decarburization process(process-Ⅰ), and increasing the oxygen content at the end of RH decarburization, heating and final deoxidation by one-time Al addition(process-Ⅱ). Temperature increases of 10°C by different processes were studied; the results showed that the two heating processes could achieve the same heating effect. The T.[O] content in the slab and the refining process was better controlled by process-Ⅰ than by process-Ⅱ. Statistical analysis of inclusions showed that the numbers of inclusions in the slab obtained by process-Ⅰ were substantially less than those in the slab obtained by process-Ⅱ. For process-Ⅰ, the Al_2O_3 inclusions produced by Al added to induce heating were substantially removed at the end of decarburization. The amounts of inclusions were substantially greater for process-Ⅱ than for process-Ⅰ at different refining stages because of the higher dissolved oxygen concentration in process-Ⅱ. Industrial test results showed that process-Ⅰ was more beneficial for improving the cleanliness of molten steel.

Exploration and Application Practice of Energy Conservation Theory and Method in Steel Manufacturing Process System

This article briefly discusses the theoretical basis and overall goals of energy conservation in the steel manufacturing process system.It is proposed that in the process of implementing system energy conservation,it is necessary to fully recognize and utilize the characteristics and functional advantages of the steel manufacturing process,pay more attention to energy quality,firmly grasp the overall goal of system optimization,focus on the integrated optimization of gas,steam,and waste heat systems,and propose the idea of constructing a"steel chemi-cal gas electricity heating cooling multi generation system".Based on practice,the main principles,models,and effects of implementing systematic energy conservation in steel enterprises have been proposed.

Mathematical modelling and numerical optimization of particle heating process in copper flash furnace

A mathematical model of the particle heating process in the reaction shaft of flash smelting furnace was established and the calculation was performed.The results indicate that radiation plays a significant role in the heat transfer process within the first 0.6 m in the upper part of the reaction shaft,whilst the convection is dominant in the area below 0.6 m for the particle heating.In order to accelerate the particle ignition,it is necessary to enhance the convection,thus to speed up the particle heating.A high-speed preheated oxygen jet technology was then suggested to replace the nature gas combustion in the flash furnace,aiming to create a lateral disturbance in the gaseous phase around the particles,so as to achieve a slip velocity between the two phases and a high convective heat transfer coefficient.Numerical simulation was carried out for the cases with the high-speed oxygen jet and the normal nature gas burners.The results show that with the high-speed jet technology,particles are heated up more rapidly and ignited much earlier,especially within the area of the radial range of R=0.3−0.6 m.As a result,a more efficient smelting process can be achieved under the same operational condition.

Numerical simulation of temperature distribution and heat transfer during solidification of titanium alloy ingots in vacuum arc remelting process

In order to get a better understanding of the vacuum consumable arc remelting(VAR) processes and thus to optimize them,a 3D finite element model was developed for the temperature fields and heat transfer of titanium alloy ingots during VAR process.The results show that the temperature fields obtained by the simulation are well validated through the experiment results.The temperature distribution is different during the whole VAR process and the steady-state molten pool forms at 329 s for d100 mm × 180 mm ingots.At the initial stage of remelting,the heat dissipation of crucible bottom plays an important role in the whole heat dissipation system.At the middle of remelting,the crucible wall becomes a major heat dissipation way.The effect of cooling velocity on the solidification structure of ingots was investigated based on the temperature fields and the results can well explain the macrostructure of titanium alloy ingots.

CHARACTERISTICS OF THE LATENT HEAT DUE TO DIFFERENT CLOUD MICROPHYSICAL PROCESSES AND THEIR INFLUENCE ON AN AUTUMN HEAVY RAIN EVENT OVER HAINAN ISLAND

We analyzed cloud microphysical processes' latent heat characteristics and their influence on an autumn heavy rain event over Hainan Island,China,using the mesoscale numerical model WRF and WRF-3DVAR system.We found that positive latent heat occurred far above the zero layer,while negative latent heat occurred mainly under the zero layer.There was substantially more positive latent heat than negative latent heat,and the condensation heating had the most important contribution to the latent heat increase.The processes of deposition,congelation,melting and evaporation were all characterized by weakening after their intensification;however,the variations in condensation and sublimation processes were relatively small.The main cloud microphysical processes for positive latent heat were condensation of water vapor into cloud water,the condensation of rain,and the deposition increase of cloud ice,snow and graupel.The main cloud microphysical processes for negative latent heat were the evaporation of rain,the melting and enhanced melting of graupel.The latent heat releases due to different cloud microphysical processes have a significant impact on the intensity of precipitation.Without the condensation and evaporation of rain,the total latent heating would decrease and the moisture variables and precipitation would reduce significantly.Without deposition and sublimation,the heating in high levels would decrease and the precipitation would reduce.Without congelation and melting,the latent heating would enhance in the low levels,and the precipitation would reduce.

Surface Rainfall Processes during the Genesis Period of Tropical Cyclone Durian(2001)

The rainfall processes during the formation of tropical cyclone(TC) Durian(2001) were investigated quantitatively using the three-dimensional(3 D) WRF-based precipitation equation. The rain rate(PS) decreased slightly as the TC approached to formation, and then increased as Durian began to intensify. The rate of moisture-related processes(QWV) in the equation contributed around 80% to PSbefore TC genesis, and made more contribution during and after TC genesis. The rate of hydrometeor-related processes(QCM) contributed about 20% before TC formation, followed by less contribution during and after TC formation. QWVwere dominated by the 3 D moisture flux advection rate(QWVA), while the surface evaporation rate(QWVE) also played an important role. Just before TC genesis, moisture from QWVAand QWVEhelped the local atmosphere moisten(negative QWVL). QCMwere determined by the 3 D hydrometeor advection rates(QCLAand QCIA) and the local change rates of hydrometeors(QCLLand QCIL). During TC formation, QCMlargely decreased and then reactivated as Durian began to intensify, accompanied by the development of TC cloud. Both the height and the strength of the net latent heating center associated with microphysical processes generally lowered before and during TC genesis, resulting mainly from lessening deposition and condensation. The downward shift of the net latent heating center induced a more bottom-heavy upward mass flux profile, suggesting to promote lower-tropospheric convergence in a shallower layer, vorticity amplification and TC spin-up.

Optimization of Dividing Wall Column with Heat Transfer Process Across the Wall for Feed Properties Variation

This paper investigates the thermal-coupled effect across the wall and the optimal heat transfer region of the wall for enhancing the energy saving effect of dividing wall column (DWC), and also studies the effects of feed thermal condition (q) and middle component composition of feed (cB) on the heat transfer process, the optimal heat transfer region, and the maximum heat transfer quantity across the wall. The simulation results show that the maximum heat transfer quantity across the wall and the potential for energy saving increase with the increase of q, while with the limitation of temperature difference across the wall, the beneficial heat transfer effect between certain range of stages, which are involved in the optimal heat transfer region, cannot be realized completely for a specific value of q. Besides, compared with q, a changing cB does not change the degree of realizing the beneficial heat transfer effect, but can bring about the variation of liquid split ratio (RL) and vapor split ratio (Rv). Thus, for achieving a maximum energy-saving effect of DWC, different q and cB need to find its own corresponding suitable heat transfer process across the wall.

Study on the automatic process of line heating for pillow shape plate

This paper focuses on the process for pillow shape plate by line heating technique, which is widely applied in the production of ship hull. Based on the analysis of primary parameters and experimental data in line heating process, the amount of local contraction generated by line heating has been illustrated. Then, combining with the computational result of local deformation determined by shell plate development, an optimization method for line heating parameters has been studied. This prediction system may provide rational arrangements of heating lines and technical parameters of process. By integrating the prediction system into the line heating robot for pillow shape plate, the automatic process of line heating for pillow shape plate can be achieved.

Numerical simulation of dynamic thermal process during doublesided asymmetrical TIG backing welding of large thick plates

The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.

Relationships between the surface quality of a single crystal copper ingot and the process parameters of a heated mould continuous casting method

The relationships between the surface quality of a single crystal copper ingot and the process parameters of heated mould continuous casting method were studied experimentally using our own design of horizontal heated mould continuous casting apparatus, and the mechanism by which process parameters affect the surface quality of a single crystal copper ingot is analyzed in the present paper. The results show that the process parameters affect the surface quality of a pure copper ingot by affecting the position of the liquid-solid interface in the mould. The position of the liquid-solid interface in the mould must be controlled carefully within an appropriate range, which is determined through a series of experiments, in order to gain a single crystal copper ingot with good surface quality.

Thermo-Calc calculations and studies of the heating process of Fe_(83)Si_4B_(13) alloy

The microstructural changes of Fe83Si4B13 amorphous mother alloy during the heating process were investigated by Laser Scanning Confocal Microscopy （LSCM） ,and the phase transformation was determined by the Thermo-Calc calculations. The differences in the melting points measured by Differential Scanning Calorimetry （DSC） and LSCM, and those obtained by Thermo-Calc calculations were also discussed. It is found that the melting points measured by DSC and LSCM are relatively similar, whereas the onset and end of the melting temperatures calculated by Thermo-Calc software are higher than those measured by DSC and observed by LSCM.

Reducing Efficiencies of the Commonly Used Heat Treatment Methods and Fermentation Processes on Aflatoxin M1 in Naturally Contaminated Fresh Cow Milk

The reducing efficiencies of the commonly used heat treatment methods and fermentation processes on aflatoxin M1 (AFM1) in Nigeria were investigated. Seventy samples of fresh cow milk from both conventional and traditional dairy cattle herds were collected and analyzed for the determination of AFM1 using Cobra-cell incorporated high performance liquid chromatography. Of these analyzed samples, 56 (80.0%) tested positive for AFM1 out of which 3 milk samples with high AFM1 concentrations were selectively pooled and subjected to varied conditions of heat treatments and fermentation processes using both indigenized and exotic strains of lactic acid bacteria (Lactobacillus bulgaricus + Streptococcus thermophilus and L. rhamnosus and L. plantarum) as starter cultures respectively. Both processes used either singly or combined, demonstrated high degrees of reducing effects on AFM1 levels. Sterilization of the milk at 121?C and 80?C under the same condition of time (15 - 20) min showed significant reduction of up to 58.8% (p 0.05) in the level of AFM1 when compared with the initial mean AFM1 concentration of the untreated fresh milk. The situation was however different around the boiling temperature of 100?C at which point the level of AFM1 reduction was found to be inconsistent. The indigenized combined strains showed some slight margins of AFM1 reduction in the proportions of (20.5, 30.8 and 43.9)% over and above that of the exotic strains (17.4, 30.0 and 41.1)% in 12 h, 48 h and 72 h of fermentation respectively. Generally, fermentation alone showed lower reduction of AFM1 in milk from 24.5% to 43.9% compared with the reducing activities of (35.4 to 58.8)% when heat-treated milk samples were subsequently subjected to varied fermentation conditions.

Estimation on Global Reaction Heat for the Aromatization Process of Liquefied Petroleum Gas

The reaction heat effect analysis for the aromatization process of Liquefied Petroleum Gas (LPG) was completed in this paper. In order to characterize this complex reaction system, one set of independent reactions was determined by means of atomic coefficient matrix method. Based on reaction thermodynamic and stoichiometric knowledge, the heat effect, Gibbs free energy change and equilibrium constant for each independent reaction was calculated for the specified conditions. Under these conditions, based on the initial and final composition data from LPG aromatization experiments, the actual extent of reaction for each independent reaction was determined. Furthermore, the global reaction heat and adiabatic temperature rise of LPG aromatization reaction system could be estimated. This work would provide a theoretical guidance for the design and scale-up of reactor for LPG aromatization process, as well as for the selection of proper operating conditions.

Simulation and design of a heat-integrated double-effect reactive distillation process for propylene glycol methyl ether production

A double-effect reactive distillation(DERD)process was proposed for the production of propylene glycol methyl ether from propylene oxide and methanol to overcome the shortcoming of low selectivity and high-energy consumption in the tubular plug-flow reactor.A single-column reactive distillation(RD)process was conducted under optimized operating conditions based on sensitivity analysis as a reference.The results demonstrated that the proposed DERD process is able to achieve more than 95%selectivity of the desired product.After that,a design approach of the DERD process with an objective of the minimum operating cost was proposed to achieve further energy savings in the RD process.The proposed DERD configuration can provide a large energy-savings by totally utilization of the overhead vapor steam in the high-pressure RD column.A comparison of the single-column RD process revealed that the proposed DERD process can reduce the operating cost and the total annual cost of 25.3%and 30.7%,respectively,even though the total capital cost of DERD process is larger than that of the RD process.