A new hybrid method, Monte-Carlo-Heat-Flux (MCHF) method, was presented to analyze the radiative heat transfer of participating medium in a three-dimensional rectangular enclosure using combined the Monte-Carlo meth...A new hybrid method, Monte-Carlo-Heat-Flux (MCHF) method, was presented to analyze the radiative heat transfer of participating medium in a three-dimensional rectangular enclosure using combined the Monte-Carlo method with the heat flux method. Its accuracy and reliability was proved by comparing the computational results with exact results from classical "Zone Method".展开更多
Piloti is commonly used in tropical and subtropical climate zones to get high wind velocity and create shadowed areas in order to optimize the living environment of residential blocks,but there are few studies to reve...Piloti is commonly used in tropical and subtropical climate zones to get high wind velocity and create shadowed areas in order to optimize the living environment of residential blocks,but there are few studies to reveal the influence of piloti on the radiant environment of residential blocks systematically. Taking the city of Guangzhou as an example,using 3-D Unsteady State Heat Balance Radiation Calculation Method,this paper shows that the mean radiant temperature( MRT) under piloti area increases with the increase of piloti ratio,and especially when piloti ratio is equal to 100%,the MRT increase trend becomes sharp. The MRT of exposed area decreases with the increase of piloti ratio,especially when piloti ratio reaches 100%,the decrease trend of MRT becomes sharp,which offers the reference for the study on piloti design in subtropical climate zones and further research on living environment by CFD simulation in residential blocks.展开更多
The results stemming from the calculation of heat transfer in torch furnaces by the laws, relating to radiation from solid surfaces and gas volumes are analyzed. The article presents the laws for radiation from gas vo...The results stemming from the calculation of heat transfer in torch furnaces by the laws, relating to radiation from solid surfaces and gas volumes are analyzed. The article presents the laws for radiation from gas volumes and the procedure for calculating heat transfer in torch furnaces, fire boxes, and combustion chambers, elaborated on their basis. The example of heat transfer calculation in a torch furnace is given, and it is significantly non-uniform in nature. Non-uniformity of heat flux distribution on heating surfaces is given. According to the results of calculations, a new furnace is designed to decrease the non-uniformity of ingot heating, fuel rate, and increase the furnace capacity. The calculation results of the distribution of heat fluxes on the heating surfaces are given in changing torch geometric dimensions. These results are confirmed by experimental studies.展开更多
A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot parti...A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot particles are spherical. That in this formula there consist neither constants needing adjustments nor variables related to engine types or operating conditions makes it universal and easy to use. Also it can be seen from the formula that radiation heat transfer is proportional to the quotient of in-cylinder soot mass over the average radius of primary particles. Besides, with the help of different algorithms it can be used for predicting cylinders' global as well as local radiation heat flows. As a demonstrative application on its global facet, a three-dimension simulation study about the soot-radiation-related heat flow in the combustion chamber of a diesel engine is carried out. Results show that the range of the soot-radiation-related heat flow computed by this formula agrees well with other researcher's earlier theoretic reasoning and experimental measurements.展开更多
The impact of soil moisture availability on the Bowen ratio and on the partition of net radiation flux into sensible, latent and soil heat fluxes was investigated by using one-dimensional primitive equations with a re...The impact of soil moisture availability on the Bowen ratio and on the partition of net radiation flux into sensible, latent and soil heat fluxes was investigated by using one-dimensional primitive equations with a refined soil parameterization scheme. Simulation results presented that as soil moisture availability increases, the Bowen ratio and the partition of net radiation flux into sensible and soil heat fluxes decrease. The partition of net radiation flux into latent heat flux, however, increases. Quantitative relationships between Bowen ratio and the partitions with soil moisture availability were also given in this study.展开更多
We investigated the ability of four popular Machine Learning methods i.e.,Deep Neural Networks(DNNs),Random Forest-based regressors(RFRs),Extreme Gradient Boosting-based regressors(XGBs),and stacked ensembles of DNNs,...We investigated the ability of four popular Machine Learning methods i.e.,Deep Neural Networks(DNNs),Random Forest-based regressors(RFRs),Extreme Gradient Boosting-based regressors(XGBs),and stacked ensembles of DNNs,to model the radiative heat transfer based on view factors in bi-and polydisperse particle beds including walls.Before training and analyzing the predictive capability of each method,an adjustment of markers used in monodisperse systems,as well as an evaluation of new markers was performed.On the basis of our dataset that considers a wide range of particle radii ratios,system sizes,particle volume fractions,as well as different particle-species volume fractions,we found that(i)the addition of particle size information allows the transition from monodisperse to bi-and polydisperse beds,and(ii)the addition of particle volume fraction information as the fourth marker leads to very accurate predictions.In terms of the overall performance,DNNs and RFRs should be preferred compared to the other two options.For particle-particle view factors,DNN and RFR are on par,while for particle-wall the RFR is superior.We demonstrate that DNNs and RFRs can be built to meet or even exceed the prediction quality standards achieved in a monodisperse system.展开更多
Building is an important scenario for achieving global carbon peak and carbon neutrality goals,accounting for approximately 37%of global energy-related CO_(2) emissions in 2020.In the meanwhile,the construction and op...Building is an important scenario for achieving global carbon peak and carbon neutrality goals,accounting for approximately 37%of global energy-related CO_(2) emissions in 2020.In the meanwhile,the construction and operation of buildings was responsible for 36%of global energy consumption,of which 30%energy was used for space heating.Therefore,this paper proposes a low-carbon building heating system that is coupled to a new semiconductor radiation heating unit and distributed rooftop photovoltaic to reduce carbon emissions.To reveal its building heating characteristics,a dynamic model of heat transfer based on semiconductor low-temperature radiant heating is first established by analyzing the heat conduction,convection,and radiation models,and the uncertainty from both the distributed rooftop photovoltaic and building heating demand is considered in the building heating operation strategy.Then,a simulation model of a low-carbon building heating system is built in MATLAB/SIMULINK for two different climate zones in China(Beijing and Wuhan).When building and using the low-carbon building heating system stable for 30 years,the payback period is 5.2–8.2 years in Beijing and 6.4–11.6 years in Wuhan.Compared with the traditional grid-powered heating system,the simulation revealed that the carbon emissions of Beijing and Wuhan during the heating season are reduced by 44.9%and 44.3%,respectively,and the corresponding building heating cost is saved by 62.1%and 57.8%.展开更多
This paper introduces a new model for the Fourier law of heat conduction with the time-fractional order to the generalized Maxwell fluid. The flow is influenced by magnetic field, radiation heat, and heat source. A fr...This paper introduces a new model for the Fourier law of heat conduction with the time-fractional order to the generalized Maxwell fluid. The flow is influenced by magnetic field, radiation heat, and heat source. A fractional calculus approach is used to establish the constitutive relationship coupling model of a viscoelastic fluid. We use the Laplace transform and solve ordinary differential equations with a matrix form to obtain the velocity and temperature in the Laplace domain. To obtain solutions from the Laplace space back to the original space, the numerical inversion of the Laplace transform is used. According to the results and graphs, a new theory can be constructed. Comparisons of the associated parameters and the corresponding flow and heat transfer characteristics are presented and analyzed in detail.展开更多
Satellite's thermal control subsystem (TCS) has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing bot...Satellite's thermal control subsystem (TCS) has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing both the weight of the system and required heater power while keeping components temperature within their design range. For a space based heat pipe radiator system, several researchers have published different approaches to reach such goal. This paper presents a thermal design and optimization of a heat pipe radiator applied to a practical engineering design application. For this study, a prospective communication satellite payload panel with applied passive thermal control techniques was considered. The thermal passive techniques used in this design mainly include multilayer insulation (MLI) blankets, optical solar reflectors (OSR), selected thermal coatings, interface fillers and constant conductance heat pipes. The heat pipe network is comprised of some heat pipes embedded in the panel and some mounted on inner surface of the panel. Embedded heat pipes are placed under high heat dissipation equipments and their size is fixed; minimum weight of the radiator is achieved by a minimum weight of the mounted heat pipes. Hence, size of the mounted heat pipes is optimized. A thermal model was built and parameterized for transient thermal analysis and optimization. Temperature requirements of components in both worst case conditions (Hot case and cold case) were satisfied under optimal sizing of mounted heat pipes.展开更多
Particle melting and substrate temperature are important in controlling deposited density and residual stress in thermal plasma deposition of refractory materials. In this paper, both the heating and cooling behaviour...Particle melting and substrate temperature are important in controlling deposited density and residual stress in thermal plasma deposition of refractory materials. In this paper, both the heating and cooling behaviours of tungsten particles inside a radio frequency inductively coupled plasma (ICP) and the plasma heat flux to the substrate were investigated. The distribution of the plasma-generated heat on device, powder injection probe, deposition chamber, and substrate was determined by measuring the water flow rate and the flow-in and flow-out water temperatures in the four parts. Substrate temperature was measured by a two-colour pyrometer during the ICP deposition of tungsten. Experimental results show that the heat flux to the substrate accounts for about 20% of the total plasma energy, the substrate temperature can reach as high as 2100 K, and the heat loss by radiation is significant in the plasma deposition of tungsten.展开更多
From the microstructure of heat radiation, the interaction between theincident heat radiative wave and the electromagnetism syntonic wave is analyzed to reveal theemission, absorption, transmission and reflection mech...From the microstructure of heat radiation, the interaction between theincident heat radiative wave and the electromagnetism syntonic wave is analyzed to reveal theemission, absorption, transmission and reflection mechanisms of the incident heat radiative wave inmaterials. Based on Lorentz dispersion theory, the effect of optical parameters on heat radiativecharacteristics is also analyzed. The method of ultra-attenuation and nanocrystallization improvingthe heat radiative characteristics of the material and the emissivity dispersion of theultra-attenuated materials are brought to light.展开更多
This is the first report of using the microwave heating technique to synthesize calcium sulphide activated by europium whose structure is determined as the face-centered cubic by conventional X-ray powder diffraction ...This is the first report of using the microwave heating technique to synthesize calcium sulphide activated by europium whose structure is determined as the face-centered cubic by conventional X-ray powder diffraction method. The phosphor has maximum excitation peaks located at 280 urn and 560 urn and the maximum emission of the phosphor is 630 nm. When the concentration of Eu^(2+) in CaS increases from I .0 × 10^(-5) to l.0 × 10^(-2) mole per mole host, the body colour of the calcium sulphide activated with europium changes from white, through light-red to pink to deep-red. The phosphor obtains the longest afterglow at the concentration of 0.1% Eu^(2+)doped and is a kind of good material excited by sunlight.展开更多
This paper is concerned with the stationary plane contact of an insulated rigid punch and a half-space which is elastically anisotropic but thermally conducting. The frictional heat generation inside the contact regio...This paper is concerned with the stationary plane contact of an insulated rigid punch and a half-space which is elastically anisotropic but thermally conducting. The frictional heat generation inside the contact region due to the sliding of the punch over the half-space surface and the heat radiation outside the contact region are taken into account. With the help of Fourier integral transform, the problem is reduced to a system of two singular integral equations. The equations are solved numerically by using Gauss-Jacobi and trapezoidal-rule quadratures. The effects of anisotropy and thermal effects are shown graphically.展开更多
In the past 30 years,the effect of thermal radiation and convection heat transfer,which are predominant at high temperature and can affect the measurement accuracy of thermocouple,were not fully considered in the fiel...In the past 30 years,the effect of thermal radiation and convection heat transfer,which are predominant at high temperature and can affect the measurement accuracy of thermocouple,were not fully considered in the field of laminar flame researches.In this work,the effect of thermal radiation heat transfer was newly calculated by determining the spectral irradiation heat flux from the whole space to thermocouple and the radiation heat loss from thermocouple junction to surroundings.Analysis reveals that the thermocouple itself maintains at high temperature,resulting serious thermal radiation heat loss,which can be compensated via receiving energy from convection-transferred heat as well as thermal radiation emitted by flame and burner surface.Such method was applied to correct the temperatures measured by thermocouple in rich nitromethane flame as reference.The results indicate that the radiation heat loss plays a dominant role,while the radiations emitted by flame and burner surface account for minor contribution with the percentage of 20.78%at the height above burner(HAB)of 0.4 mm,3.63%at HAB of 2.0 mm and even smaller at higher HAB.Temperature correction states that the maximum temperature error is 117.60 K,where the effect of thermal radiation emitted by flame and burner surface is less than 1.75 K.Consequently,it is provably reasonable and feasible to concentrate on the radiation heat loss and ignore the effect of thermal radiation emitted by flame and burner in real combustion processes.展开更多
Phase change materials are one of the potential resources to replace fossil fuels in regards of supplying the energy of buildings.Basically,these materials absorb or release heat energy with the help of their latent h...Phase change materials are one of the potential resources to replace fossil fuels in regards of supplying the energy of buildings.Basically,these materials absorb or release heat energy with the help of their latent heat.Phase change materials have low thermal conductivity and this makes it possible to use the physical properties of these materials in the tropical regions where the solar radiation is more direct and concentrated over a smaller area.In this theoretical work,an attempt has been made to study the melting process of these materials by applying constant heat flux and temperature.It was found that by increasing the thickness of phase change materials’layers,due to the melting,more thermal energy is stored.Simultaneously it reduces the penetration of excessive heat into the chamber,so that by increasing the thickness of paraffin materials up to 20 mm,the rate of temperature reduction reaches more than 18%.It was also recognized that increasing the values of constant input heat flux increases buoyancy effects.Increasing the Stefan number from 0.1 to 0.3,increases the temperature by 6%.展开更多
Based on the analysis of heat radiation intensity from flame, a new mathematical model ofthe tube-wall temperatmp of heated tubes is developed by taking down-fired, upright-tube cylindricalfurnace for example. The pro...Based on the analysis of heat radiation intensity from flame, a new mathematical model ofthe tube-wall temperatmp of heated tubes is developed by taking down-fired, upright-tube cylindricalfurnace for example. The proposed mathematical model can be employed to indicate both the positionand size of the hot spot at fire-facing wall of heated tube of combustion chamber, and is characteristicof simplicity and efficiency If coupled with thermoelectric couple or infrared viewer, the presentedlocation method of combustion hot spot can offer engineers very valuable proposal to keep furnacerunning more safely The same is true for any other type of tubular furnaces.展开更多
Investigating the thermal transport properties of materials is of great importance in the field of earth science and for the development of materials under extremely high temperatures and pressures.However,it is an en...Investigating the thermal transport properties of materials is of great importance in the field of earth science and for the development of materials under extremely high temperatures and pressures.However,it is an enormous challenge to characterize the thermal and physical properties of materials using the diamond anvil cell(DAC)platform.In the present study,a steady-state method is used with a DAC and a combination of thermocouple temperature measurement and numerical analysis is performed to calculate the thermal conductivity of the material.To this end,temperature distributions in the DAC under high pressure are analyzed.We propose a three-dimensional radiative-conductive coupled heat transfer model to simulate the temperature field in the main components of the DAC and calculate in situ thermal conductivity under high-temperature and high-pressure conditions.The proposed model is based on the finite volume method.The obtained results show that heat radiation has a great impact on the temperature field of the DAC,so that ignoring the radiation effect leads to large errors in calculating the heat transport properties of materials.Furthermore,the feasibility of studying the thermal conductivity of different materials is discussed through a numerical model combined with locally measured temperature in the DAC.This article is expected to become a reference for accurate measurement of in situ thermal conductivity in DACs at high-temperature and high-pressure conditions.展开更多
Compressed thin layers of ceramic fiber insulation are used as high temperature insulating layers as well as mechanical support for catalyst coated ceramic monoliths in automotive emission control devices. Minimizatio...Compressed thin layers of ceramic fiber insulation are used as high temperature insulating layers as well as mechanical support for catalyst coated ceramic monoliths in automotive emission control devices. Minimization of energy losses, choice of material and thickness of com- pressed insulating layer are based on knowledge of their thermal physical properties. Currently, consistent meas- urements of materials in a compressed state, as they would be in emission control applications, are absent due to the absence of suitable methods for s,wh tests. A test method was developed for measurement of the thermal conductivity of compressed thin fiber layers. This paper summarizes the results of thermal conductivity and diffu- sivity measurements of 27 compressed fiber alumina -sili- ca -vermiculite materials in the range of 200 -950℃. Thermal physical properties as a function of temperature, density/mechanical pressure, thickness and composition of insulating layers are presented. The whole set of exper- imental data is generalized on 3D surface plots and de- scribed by polynomial functions. The possible heat trans- fer mechanisms governing apparent thermal conductivity of pressed insulation layers are discussed.展开更多
Under the back-side windy condition,the convection and radiation heat transfer characteristics in an iso-flux upward-facing cylindrical cavity were studied by three-dimensional numerical simulation.The impacts of cavi...Under the back-side windy condition,the convection and radiation heat transfer characteristics in an iso-flux upward-facing cylindrical cavity were studied by three-dimensional numerical simulation.The impacts of cavity tilt angle,wind incident angle and wind speed on convection and radiation heat transfer Nusselt number Nuc and Nur were analyzed,and the possible explanations for their impacts were presented.Results show that due to the disturbance of wind,the influence of cavity tilt angle becomes more complicated and is related to wind incident angle and wind speed.The variation of Nuc or Nur with wind incident angle is different for different cavity tilt angles.Despite of the changes of cavity tilt angle or wind incident angle,the Nuc increases with the wind speed while the Nur presents a declination with the increasing of wind speed.Hence,compared with cavity tilt angle and wind incident angle,wind speed may be the dominant factor affecting or controlling the convective and radiation heat transfer of cavity.展开更多
In this paper,we are concerned with the numerical approximation of a steady-state heat radiation problem with a nonlinear Stefan-Boltzmann boundary condition in IR^(3).We first derive an equivalent minimization probl...In this paper,we are concerned with the numerical approximation of a steady-state heat radiation problem with a nonlinear Stefan-Boltzmann boundary condition in IR^(3).We first derive an equivalent minimization problem and then present a finite element analysis to the solution of such a minimization problem.Moreover,we apply the Newton iterative method for solving the nonlinear equation resulting from the minimization problem.A numerical example is given to illustrate theoretical results.展开更多
基金financially supported by the National Natural Science Foundation of China (No.50464004)
文摘A new hybrid method, Monte-Carlo-Heat-Flux (MCHF) method, was presented to analyze the radiative heat transfer of participating medium in a three-dimensional rectangular enclosure using combined the Monte-Carlo method with the heat flux method. Its accuracy and reliability was proved by comparing the computational results with exact results from classical "Zone Method".
基金Sponsored by the Strategic Japanese-Chinese Cooperation Program (Grant No.2011DFA91210)the Fundamental Research Funds for the Central Universities (Grant No.HIT.NSRIF.2014075),the Fundamental Research Funds for the Central Universities (Grant No.HIT.KISTP.201419)the Natural Science Foundation of Heilongjiang Province (Grant No.E201316)
文摘Piloti is commonly used in tropical and subtropical climate zones to get high wind velocity and create shadowed areas in order to optimize the living environment of residential blocks,but there are few studies to reveal the influence of piloti on the radiant environment of residential blocks systematically. Taking the city of Guangzhou as an example,using 3-D Unsteady State Heat Balance Radiation Calculation Method,this paper shows that the mean radiant temperature( MRT) under piloti area increases with the increase of piloti ratio,and especially when piloti ratio is equal to 100%,the MRT increase trend becomes sharp. The MRT of exposed area decreases with the increase of piloti ratio,especially when piloti ratio reaches 100%,the decrease trend of MRT becomes sharp,which offers the reference for the study on piloti design in subtropical climate zones and further research on living environment by CFD simulation in residential blocks.
文摘The results stemming from the calculation of heat transfer in torch furnaces by the laws, relating to radiation from solid surfaces and gas volumes are analyzed. The article presents the laws for radiation from gas volumes and the procedure for calculating heat transfer in torch furnaces, fire boxes, and combustion chambers, elaborated on their basis. The example of heat transfer calculation in a torch furnace is given, and it is significantly non-uniform in nature. Non-uniformity of heat flux distribution on heating surfaces is given. According to the results of calculations, a new furnace is designed to decrease the non-uniformity of ingot heating, fuel rate, and increase the furnace capacity. The calculation results of the distribution of heat fluxes on the heating surfaces are given in changing torch geometric dimensions. These results are confirmed by experimental studies.
基金Sponsored by the National "973" Program Projects(652345)
文摘A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot particles are spherical. That in this formula there consist neither constants needing adjustments nor variables related to engine types or operating conditions makes it universal and easy to use. Also it can be seen from the formula that radiation heat transfer is proportional to the quotient of in-cylinder soot mass over the average radius of primary particles. Besides, with the help of different algorithms it can be used for predicting cylinders' global as well as local radiation heat flows. As a demonstrative application on its global facet, a three-dimension simulation study about the soot-radiation-related heat flow in the combustion chamber of a diesel engine is carried out. Results show that the range of the soot-radiation-related heat flow computed by this formula agrees well with other researcher's earlier theoretic reasoning and experimental measurements.
文摘The impact of soil moisture availability on the Bowen ratio and on the partition of net radiation flux into sensible, latent and soil heat fluxes was investigated by using one-dimensional primitive equations with a refined soil parameterization scheme. Simulation results presented that as soil moisture availability increases, the Bowen ratio and the partition of net radiation flux into sensible and soil heat fluxes decrease. The partition of net radiation flux into latent heat flux, however, increases. Quantitative relationships between Bowen ratio and the partitions with soil moisture availability were also given in this study.
文摘We investigated the ability of four popular Machine Learning methods i.e.,Deep Neural Networks(DNNs),Random Forest-based regressors(RFRs),Extreme Gradient Boosting-based regressors(XGBs),and stacked ensembles of DNNs,to model the radiative heat transfer based on view factors in bi-and polydisperse particle beds including walls.Before training and analyzing the predictive capability of each method,an adjustment of markers used in monodisperse systems,as well as an evaluation of new markers was performed.On the basis of our dataset that considers a wide range of particle radii ratios,system sizes,particle volume fractions,as well as different particle-species volume fractions,we found that(i)the addition of particle size information allows the transition from monodisperse to bi-and polydisperse beds,and(ii)the addition of particle volume fraction information as the fourth marker leads to very accurate predictions.In terms of the overall performance,DNNs and RFRs should be preferred compared to the other two options.For particle-particle view factors,DNN and RFR are on par,while for particle-wall the RFR is superior.We demonstrate that DNNs and RFRs can be built to meet or even exceed the prediction quality standards achieved in a monodisperse system.
基金supported by the National Natural Science Foundation of China(No.52006114).
文摘Building is an important scenario for achieving global carbon peak and carbon neutrality goals,accounting for approximately 37%of global energy-related CO_(2) emissions in 2020.In the meanwhile,the construction and operation of buildings was responsible for 36%of global energy consumption,of which 30%energy was used for space heating.Therefore,this paper proposes a low-carbon building heating system that is coupled to a new semiconductor radiation heating unit and distributed rooftop photovoltaic to reduce carbon emissions.To reveal its building heating characteristics,a dynamic model of heat transfer based on semiconductor low-temperature radiant heating is first established by analyzing the heat conduction,convection,and radiation models,and the uncertainty from both the distributed rooftop photovoltaic and building heating demand is considered in the building heating operation strategy.Then,a simulation model of a low-carbon building heating system is built in MATLAB/SIMULINK for two different climate zones in China(Beijing and Wuhan).When building and using the low-carbon building heating system stable for 30 years,the payback period is 5.2–8.2 years in Beijing and 6.4–11.6 years in Wuhan.Compared with the traditional grid-powered heating system,the simulation revealed that the carbon emissions of Beijing and Wuhan during the heating season are reduced by 44.9%and 44.3%,respectively,and the corresponding building heating cost is saved by 62.1%and 57.8%.
基金Project supported by the China Postdoctoral Science Foundation(No.2015M580069)
文摘This paper introduces a new model for the Fourier law of heat conduction with the time-fractional order to the generalized Maxwell fluid. The flow is influenced by magnetic field, radiation heat, and heat source. A fractional calculus approach is used to establish the constitutive relationship coupling model of a viscoelastic fluid. We use the Laplace transform and solve ordinary differential equations with a matrix form to obtain the velocity and temperature in the Laplace domain. To obtain solutions from the Laplace space back to the original space, the numerical inversion of the Laplace transform is used. According to the results and graphs, a new theory can be constructed. Comparisons of the associated parameters and the corresponding flow and heat transfer characteristics are presented and analyzed in detail.
文摘Satellite's thermal control subsystem (TCS) has to maintain components and structure within their specified temperature limits during satellite service life. TCS designers have to face the challenge of reducing both the weight of the system and required heater power while keeping components temperature within their design range. For a space based heat pipe radiator system, several researchers have published different approaches to reach such goal. This paper presents a thermal design and optimization of a heat pipe radiator applied to a practical engineering design application. For this study, a prospective communication satellite payload panel with applied passive thermal control techniques was considered. The thermal passive techniques used in this design mainly include multilayer insulation (MLI) blankets, optical solar reflectors (OSR), selected thermal coatings, interface fillers and constant conductance heat pipes. The heat pipe network is comprised of some heat pipes embedded in the panel and some mounted on inner surface of the panel. Embedded heat pipes are placed under high heat dissipation equipments and their size is fixed; minimum weight of the radiator is achieved by a minimum weight of the mounted heat pipes. Hence, size of the mounted heat pipes is optimized. A thermal model was built and parameterized for transient thermal analysis and optimization. Temperature requirements of components in both worst case conditions (Hot case and cold case) were satisfied under optimal sizing of mounted heat pipes.
文摘Particle melting and substrate temperature are important in controlling deposited density and residual stress in thermal plasma deposition of refractory materials. In this paper, both the heating and cooling behaviours of tungsten particles inside a radio frequency inductively coupled plasma (ICP) and the plasma heat flux to the substrate were investigated. The distribution of the plasma-generated heat on device, powder injection probe, deposition chamber, and substrate was determined by measuring the water flow rate and the flow-in and flow-out water temperatures in the four parts. Substrate temperature was measured by a two-colour pyrometer during the ICP deposition of tungsten. Experimental results show that the heat flux to the substrate accounts for about 20% of the total plasma energy, the substrate temperature can reach as high as 2100 K, and the heat loss by radiation is significant in the plasma deposition of tungsten.
文摘From the microstructure of heat radiation, the interaction between theincident heat radiative wave and the electromagnetism syntonic wave is analyzed to reveal theemission, absorption, transmission and reflection mechanisms of the incident heat radiative wave inmaterials. Based on Lorentz dispersion theory, the effect of optical parameters on heat radiativecharacteristics is also analyzed. The method of ultra-attenuation and nanocrystallization improvingthe heat radiative characteristics of the material and the emissivity dispersion of theultra-attenuated materials are brought to light.
基金This work was supported by the National NatUral Science Foundation of China! (No 59982003) Guangdong Provincial NatUral Scie
文摘This is the first report of using the microwave heating technique to synthesize calcium sulphide activated by europium whose structure is determined as the face-centered cubic by conventional X-ray powder diffraction method. The phosphor has maximum excitation peaks located at 280 urn and 560 urn and the maximum emission of the phosphor is 630 nm. When the concentration of Eu^(2+) in CaS increases from I .0 × 10^(-5) to l.0 × 10^(-2) mole per mole host, the body colour of the calcium sulphide activated with europium changes from white, through light-red to pink to deep-red. The phosphor obtains the longest afterglow at the concentration of 0.1% Eu^(2+)doped and is a kind of good material excited by sunlight.
文摘This paper is concerned with the stationary plane contact of an insulated rigid punch and a half-space which is elastically anisotropic but thermally conducting. The frictional heat generation inside the contact region due to the sliding of the punch over the half-space surface and the heat radiation outside the contact region are taken into account. With the help of Fourier integral transform, the problem is reduced to a system of two singular integral equations. The equations are solved numerically by using Gauss-Jacobi and trapezoidal-rule quadratures. The effects of anisotropy and thermal effects are shown graphically.
基金the financial support from National Natural Science Foundation of China(No.51976216,No.51888103)the Ministry of Science and Technology of China(2017YFA0402800)+2 种基金Beijing Municipal Natural Science Foundation(JQ20017)K.C.Wong Education FoundationRecruitment Program of Global Youth Experts。
文摘In the past 30 years,the effect of thermal radiation and convection heat transfer,which are predominant at high temperature and can affect the measurement accuracy of thermocouple,were not fully considered in the field of laminar flame researches.In this work,the effect of thermal radiation heat transfer was newly calculated by determining the spectral irradiation heat flux from the whole space to thermocouple and the radiation heat loss from thermocouple junction to surroundings.Analysis reveals that the thermocouple itself maintains at high temperature,resulting serious thermal radiation heat loss,which can be compensated via receiving energy from convection-transferred heat as well as thermal radiation emitted by flame and burner surface.Such method was applied to correct the temperatures measured by thermocouple in rich nitromethane flame as reference.The results indicate that the radiation heat loss plays a dominant role,while the radiations emitted by flame and burner surface account for minor contribution with the percentage of 20.78%at the height above burner(HAB)of 0.4 mm,3.63%at HAB of 2.0 mm and even smaller at higher HAB.Temperature correction states that the maximum temperature error is 117.60 K,where the effect of thermal radiation emitted by flame and burner surface is less than 1.75 K.Consequently,it is provably reasonable and feasible to concentrate on the radiation heat loss and ignore the effect of thermal radiation emitted by flame and burner in real combustion processes.
文摘Phase change materials are one of the potential resources to replace fossil fuels in regards of supplying the energy of buildings.Basically,these materials absorb or release heat energy with the help of their latent heat.Phase change materials have low thermal conductivity and this makes it possible to use the physical properties of these materials in the tropical regions where the solar radiation is more direct and concentrated over a smaller area.In this theoretical work,an attempt has been made to study the melting process of these materials by applying constant heat flux and temperature.It was found that by increasing the thickness of phase change materials’layers,due to the melting,more thermal energy is stored.Simultaneously it reduces the penetration of excessive heat into the chamber,so that by increasing the thickness of paraffin materials up to 20 mm,the rate of temperature reduction reaches more than 18%.It was also recognized that increasing the values of constant input heat flux increases buoyancy effects.Increasing the Stefan number from 0.1 to 0.3,increases the temperature by 6%.
基金This project is supported by National Natural Science Foundation of China(No.50175081).
文摘Based on the analysis of heat radiation intensity from flame, a new mathematical model ofthe tube-wall temperatmp of heated tubes is developed by taking down-fired, upright-tube cylindricalfurnace for example. The proposed mathematical model can be employed to indicate both the positionand size of the hot spot at fire-facing wall of heated tube of combustion chamber, and is characteristicof simplicity and efficiency If coupled with thermoelectric couple or infrared viewer, the presentedlocation method of combustion hot spot can offer engineers very valuable proposal to keep furnacerunning more safely The same is true for any other type of tubular furnaces.
基金Project supported by the National Key Research and Development Program of China(Grant No.2018YFA0702700)the National Natural Science Foundation of China(Grant Nos.11674404 and 11774126)。
文摘Investigating the thermal transport properties of materials is of great importance in the field of earth science and for the development of materials under extremely high temperatures and pressures.However,it is an enormous challenge to characterize the thermal and physical properties of materials using the diamond anvil cell(DAC)platform.In the present study,a steady-state method is used with a DAC and a combination of thermocouple temperature measurement and numerical analysis is performed to calculate the thermal conductivity of the material.To this end,temperature distributions in the DAC under high pressure are analyzed.We propose a three-dimensional radiative-conductive coupled heat transfer model to simulate the temperature field in the main components of the DAC and calculate in situ thermal conductivity under high-temperature and high-pressure conditions.The proposed model is based on the finite volume method.The obtained results show that heat radiation has a great impact on the temperature field of the DAC,so that ignoring the radiation effect leads to large errors in calculating the heat transport properties of materials.Furthermore,the feasibility of studying the thermal conductivity of different materials is discussed through a numerical model combined with locally measured temperature in the DAC.This article is expected to become a reference for accurate measurement of in situ thermal conductivity in DACs at high-temperature and high-pressure conditions.
文摘Compressed thin layers of ceramic fiber insulation are used as high temperature insulating layers as well as mechanical support for catalyst coated ceramic monoliths in automotive emission control devices. Minimization of energy losses, choice of material and thickness of com- pressed insulating layer are based on knowledge of their thermal physical properties. Currently, consistent meas- urements of materials in a compressed state, as they would be in emission control applications, are absent due to the absence of suitable methods for s,wh tests. A test method was developed for measurement of the thermal conductivity of compressed thin fiber layers. This paper summarizes the results of thermal conductivity and diffu- sivity measurements of 27 compressed fiber alumina -sili- ca -vermiculite materials in the range of 200 -950℃. Thermal physical properties as a function of temperature, density/mechanical pressure, thickness and composition of insulating layers are presented. The whole set of exper- imental data is generalized on 3D surface plots and de- scribed by polynomial functions. The possible heat trans- fer mechanisms governing apparent thermal conductivity of pressed insulation layers are discussed.
基金funded by National Key Research and Development Program of China(Grant No.2017YFB0602002,and Grant No.2016YFC0203700)。
文摘Under the back-side windy condition,the convection and radiation heat transfer characteristics in an iso-flux upward-facing cylindrical cavity were studied by three-dimensional numerical simulation.The impacts of cavity tilt angle,wind incident angle and wind speed on convection and radiation heat transfer Nusselt number Nuc and Nur were analyzed,and the possible explanations for their impacts were presented.Results show that due to the disturbance of wind,the influence of cavity tilt angle becomes more complicated and is related to wind incident angle and wind speed.The variation of Nuc or Nur with wind incident angle is different for different cavity tilt angles.Despite of the changes of cavity tilt angle or wind incident angle,the Nuc increases with the wind speed while the Nur presents a declination with the increasing of wind speed.Hence,compared with cavity tilt angle and wind incident angle,wind speed may be the dominant factor affecting or controlling the convective and radiation heat transfer of cavity.
文摘In this paper,we are concerned with the numerical approximation of a steady-state heat radiation problem with a nonlinear Stefan-Boltzmann boundary condition in IR^(3).We first derive an equivalent minimization problem and then present a finite element analysis to the solution of such a minimization problem.Moreover,we apply the Newton iterative method for solving the nonlinear equation resulting from the minimization problem.A numerical example is given to illustrate theoretical results.