Optimal Scheduling Method of Cogeneration System with Heat Storage Device Based on Memetic Algorithm

Electric-heat coupling characteristics of a cogeneration system and the operating mode of fixing electricity with heat are the main reasons for wind abandonment during the heating season in the Three North area.To improve the wind-power absorption capacity and operating economy of the system,the structure of the system is improved by adding a heat storage device and an electric boiler.First,aiming at the minimum operating cost of the system,the optimal scheduling model of the cogeneration system,including a heat storage device and electric boiler,is constructed.Second,according to the characteristics of the problem,a cultural gene algorithm program is compiled to simulate the calculation example.Finally,through the system improvement,the comparison between the conditions before and after and the simulation solutions of similar algorithms prove the effectiveness of the proposed scheme.The simulation results show that adding the heat storage device and electric boiler to the scheduling optimization process not only improves the wind power consumption capacity of the cogeneration system but also reduces the operating cost of the system by significantly reducing the coal consumption of the unit and improving the economy of the system operation.The cultural gene algorithm framework has both the global evolution process of the population and the local search for the characteristics of the problem,which has a better optimization effect on the solution.

Interannual variability of mixed layer depth and heat storage of upper layer in the tropical Pacific Ocean

By using the upper layer data(downloaded from the web of the Scripps Institution of Oceanography),the interannual variability of the heat storage of upper layer(from surface to 400 m depth) and the mixed layer depth in the tropical Pacific Ocean are investigated. The abnormal signal of the warm event comes from the central and west Pacific Ocean, whereas it is regarded that the abnormal signal of the warm event comes from the east Pacific Ocean in the popular viewpoint. From the viewpoint on the evolution of the interannual variability of the mixed layer depth and the heat storage of the whole upper layer, the difference between the two types of El Nino is so small that it can be neglected. During these two El Nino/La Nina events(1972/1973 and 1997/1998), other than the case of the heat storage or for the mixed layer depth, the abnormal signal propagates from the central and west Pacific Ocean to the east usually by the path along the equator whereas the abnormal signal propagates from the east to the west by the path northern to the equator. For the interannual variability, the evolution of the mixed layer depth corresponds to that of the heat storage in the upper layer very well. This is quite different from the evolution of seasonality.

Simultaneous CO_(2) capture and thermochemical heat storage by modified carbide slag in coupled calcium looping and CaO/Ca(OH)2 cycles

The simultaneous CO_(2) capture and heat storage performances of the modified carbide slag with byproduct of biodiesel were investigated in the process coupled calcium looping and CaO/Ca(OH)2 thermochemical heat storage using air as the heat transfer fluid.The modified carbide slag with by-product of biodiesel exhibits superior CO_(2) capture and heat storage capacities in the coupled calcium looping and heat storage cycles.The hydration conversion and heat storage density of the modified carbide slag after 30 heat storage cycles are 0.65 mol·mol^(-1) and 1.14 GJ·t^(-1),respectively,which are 1.6 times as high as those of calcined carbide slag.The negative effect of CO_(2) in air as the heat storage fluid on the heat storage capacity of the modified carbide slag is overcome by introducing CO_(2) capture cycles.In addition,the CO_(2) capture reactivity of the modified carbide slag after the multiple calcium looping cycles is enhanced by the introduction of heat storage cycles.By introducing 10 heat storage cycles after the 10th and 15th CO_(2) capture cycles,the CO_(2) capture capacities of the modified carbide slag are subsequently improved by 32%and 43%,respectively.The porous and loose structure of modified carbide slag reduces the diffusion resistances of CO_(2) and steam in the material in the coupled process.The formed CaCO_(3)in the modified carbide slag as a result of air as the heat transfer fluid in heat storage cycles decomposes to regenerate CaO in calcium looping cycles,which improves heat storage capacity.Therefore,the modified carbide slag with by-product of biodiesel seems promising in the coupled calcium looping and CaO/Ca(OH)_(2) heat storage cycles.

Melting heat transfer enhancement of a horizontal latent heat storage unit by fern-fractal fins

The latent heat storage(LHS)technique is of crucial importance in chemical energy engineering.Inspired by multi-bifurcated fern leaves,a mimic fern-fractal fin is designed to improve the thermal energy charging efficiency.This paper develops a transient melting model of a rectangular LHS unit using fern-fractal fins,and their melting behaviors are compared with the conventional fins.Besides,a parametric optimization of fernfractal fins is conducted for maximizing the thermal efficiency based on the response surface method(RSM).The results indicate that the temperature uniformity is more superior and the melting duration is shorter for the fern-fractal LHS unit when compared with the conventional one.Interestingly,the fern-fractal LHS device presents a slower heat storage rate during the initial conduction-dominated and early convection-dominated melting stages,while a prominent melting enhancement is achieved during the later melting stage.The shortest melting time is obtained based on the RSM technique when a fern-fractal fin with length ratio α=0.94 and branch angle θ=54.7°is utilized.Compared with a conventional fin,the averaged heat storage rate increases by 88.3%,and the total melting time is declined by 40.3%for an optimized fern-fractal fin.

Effect of Radial Porosity Oscillation on the Thermal Performance of Packed Bed Latent Heat Storage

Owing to its high heat storage capacity and fast heat transfer rate,packed bed latent heat storage(LHS)is considered as a promising method to store thermal energy.In a packed bed,the wall effect can impact the packing arrangement of phase change material(PCM)capsules,inducing radial porosity oscillation.In this study,an actual-arrangement-based three-dimensional packed bed LHS model was built to consider the radial porosity oscillation.Its fluid flow and heat transfer were analyzed.With different cylindrical sub-surfaces intercepted along the radial direction in the packed bed,the corresponding relationships between the arrangement of capsules and porosity oscillation were identified.The oscillating distribution of radial porosity led to a non-uniform distribution of heat transfer fluid(HTF)velocity.As a result,radial temperature distributions and liquid fraction distributions of PCMs were further affected.The effects of different dimensionless parameters(e.g.,tube-to-capsule diameter ratio,Reynolds number,and Stefan number)on the radial characteristics of HTF and PCMs were discussed.The results showed that different diameter ratios correspond to different radial porosity distributions.Further,with an increase in diameter ratio,HTF velocity varies significantly in the near wall region while the non-uniformity of HTF velocity in the center region will decrease.The Reynolds and Stefan numbers slightly impact the relative velocity distribution of the HTF-while higher Reynolds numbers can lead to a proportional improvement of velocity,an increase in Stefan number can promote heat storage of the packed bed LHS system.

Synthesis and characterization of salt-impregnated anodic aluminum oxide composites for low-grade heat storage

Thermochemical heat storage(THS)systems have recently attracted a lot of attention in research and development.In this study,an anodic aluminum oxide(AAO)template,fabricated by a two-step anodization method,was used for the first time as the matrix material for a THS system.Different salts were studied as thermochemical materials for their suitability in low-grade heat storage application driven by solar energy for an open system.Compositions were prepared by absorbing CaCl2,MgCl2,LiCl,LiNO3 and mixtures of these salts under a vacuum in an AAO matrix.Field Emission Scanning Electron Microscopy was used to examine the morphology of the produced AAO composites.Thermal energy storage capacities of the composites were characterized using a differential scanning calorimeter.Characterization analysis showed that anodized Al plates were suitable matrix materials for THS systems,and composite sorbent prepared with a 1:1 ratio LiCl/LiNO3 salt mixture had the highest energy value among all composites,with an energy density of 468.1 k J·kg-1.

Fabrication of Al_2O_3-NaCl Composite Heat Storage Materials by One-step Synthesis Method

Thermal energy storage is an attractive option for effectiveness since it gives flexibility and reduces energy consumption and costs. New composite materials for storage and transformation of heat of NaCl-Al2O3composite materials were synthesized by one-step synthesis method. The chemical composition, morphology, structure, and thermal properties were investigated by XRD, EDS, SEM, and DSC. The results show that NaCl can be absorbed by Al2O3particle from 800 to 900 ℃ for Al2O3particle surface is rich active structure. The results also indicate that the leakage of NaCl when the phase change can be prevented by Al2O3particles and the enthalpy of phase change of NaCl-Al2O3material is 362 J/g. The composites have an excellent heat storage capacity. Therefore, this study contributes to one new thought and method to prepare high temperature heat storage material and this material can be applied in future thermal engineering.

Calcium looping heat storage performance and mechanical property of CaO-based pellets under fluidization

The CaO-based pellets were fabricated using extrusion-spheronization method for calcium looping thermochemical heat storage under the fluidization.The effects of adhesive,biomass-based pore-forming agent,binder and particle size on the heat storage performance and mechanical property of the CaObased pellets were investigated in a bubbling fluidized bed reactor.The addition of 2%(mass)polyvinylpyrrolidone as an adhesive not only helps granulate,but also improves the heat storage capacity of the pellets.All biomass-templated CaO-based pellets display higher heat storage capacity than biomass-free pellets,indicating that the biomass-based pore-forming agent is beneficial for heat storage under the fluidization.Especially,bagasse-templated pellets show the highest heat storage conversion of 0.61 after 10 cycles.Moreover,Al_(2)O_(3)as a binder for the pellets helps obtain high mechanical strength.The CaO-based pellets doped with 10%(mass)bagasse and 5%(mass)Al_(2)O_(3)reach the highest heat storage density of 1621 kJ·kg^(-1) after 30 cycles and the highest crushing strength of 4.98 N.The microstructure of the bagasse-templated pellets appears more porous than that of biomass-free pellets.The bagassetemplated CaO-based pellets doped with Al_(2)O_(3)seem promising for thermochemical heat storage under the fluidization,owing to the enhanced heat storage capacity,excellent mechanical strength,and simplicity of the synthesis procedure.

Effects of Porous Graphene on LiOH Based Composite Materials for Low Temperature Thermochemical Heat Storage

Thermochemical heat storage material inorganic hydrate LiOH is selected as a promising candidate material for storing low-temperature heat energy because of its high energy density(1440 kJ/kg)and mild reaction process.However,the low hydration rate of LiOH limits the performance of low temperature thermochemical heat storage system as well as the thermal conductivity.In this study,porous-graphene/LiOH composite thermochemical heat storage materials with strong water sorption property and higher thermal conductivity were synthesized by hydrothermal process.The experimental results show that the hydration rate of the composites was greatly improved.The heat storage density of the composite materials was increased by 47%(from 661 kJ/kg to 974 kJ/kg).By combing the porous graphene,the thermal conductivity of composites with different contents were highly increased by 21.1%to 78.7%,but the increase of heat storage density is opposite to that of thermal conductivity.The development of high-performance materials for thermochemical heat storage should consider the relationship between the heat storage density and thermal conductivity of the material,and the thermal conductivity of the supporter needs to be further improved.

Performance Assessment of a Box Type Solar Cooker Using Jatropha Oil as a Heat Storage Material

Solar cookers are a good option in developing countries with high solar potential for environmentally friendly cooking and reduced pressure on forests. However, they are still affected by the intermittency of the sun. In order to overcome this problem, in this work, a box type solar cooker integrated Jatropha oil as a heat storage material is fabricated and experimented with. The design was examined with a maximum stagnation temperature of 157.7°C. The recorded cooking power vanished between 78.4 and 103.6 W, while thermal efficiency varied from 41.26% to 58.78%. The energy transfer cycle test, including charge and discharge revealed that 91.18% of the heat lost through the cooker could be recovered by the heat storage unit and a large amount is restored to the system during cloudiness or a temperature perturbation.

Chemical Heat Storage Using an SiC Honeycomb Packed with CaCl₂Powder

Chemical heat storage is a promising technology for improving thermal energy efficiency. In this study, CaCl2 and H2O were selected as a reaction system for utilization of low-grade exhaust heat that is cooler than 200°C. Heat discharging and charging were conducted through the CaCl2 hydration reaction. A silicon carbide honeycomb was adopted to improve heat transfer in the CaCl2 packed bed. The heat storage, condenser, and evaporator temperature were set at 150°C, 30°C and 90°C respectively. Repeated trials and experiments are time consuming for optimizing design of the equipment. Therefore, in this research, we constructed a simulation that can predict the performance of the device. A numerical simulation model was utilized in preparation for the design of the heat storage module. The consistency of both the simulation and the experimental results was confirmed by comparing them.

Thermochemical Heat Storage Performance in the Gas/Liquid-Solid Reactions of SrCl2 with NH3

Thermochemical heat storage is a promising technology for improving energy efficiency through the utilization of low-grade waste heat. The formation of a SrCl2 ammine complex was selected as the reaction system for the purpose of this study. Discharge characteristics were evaluated in a packed bed reactor for both the gas-solid reaction and the liquid-solid reaction. The average power of the gas-solid reaction was influenced by the pressure of the supplied ammonia gas, with greater powers being recorded at higher ammonia pressure. For the liquid-solid reaction, the obtained average power was comparable to that obtained for the gas-solid reaction at 0.2 MPa. Moreover, the lower heat transfer resistance in the reactor was observed, which was likely caused by the presence of liquid ammonia in the system. Finally, the short-term durability of the liquid-solid reaction system was demonstrated over 10 stable charge/discharge cycles.

Experimental Study on Heat Storage Properties Comparison of Paraffin/Metal Foams Phase Change Material Composites

Heat storage properties of phase change materials(PCMs) are essential characteristics that perform a key role in thermal heat energy storage systems.The thermal properties of PCMs can be improved by developing metal foam/PCM composites.The addition of metal foam in PCMs has a significant effect on the thermal characteristics of PCMs.In this paper,the heat storage properties of two different metal foam/PCM composites were experimentally examined.The behavior of paraffin in metal foam(copper and iron-nickel)/paraffin composites concerning pure paraffin at a constant heat flux of 1000 W/m^(2) in three directions simultaneously(x,y,and z) was studied.Paraffin was infiltrated into copper and iron-nickel foams to develop composite materials which resulted in enhancing the thermal conductivity of the paraffin.A comparative analysis is made on the heat storage properties of paraffin in copper and iron-nickel foams/paraffin composites.Inner temperature distribution during the phase transition process is experimentally evaluated.This comparison indicates that temperature uniformity in copper foam/paraffin composite is better than in iron-nickel foam/paraffin composite and pure paraffin at the same heat flux.Experimental results show that at heat flux of 1000 W/m^(2),the heat storage time for copper foam/paraffin composite is 20.63% of that of iron-nickel foam/paraffin composite.

Heat Storage Performance of PCM in a Novel Vertical Pointer-Shaped Finned Latent Heat Tank

The heat storage performance of latent heat storage systems is not good due to the poor thermal conductivity of phase change materials.In this paper,a new type of pointer-shaped fins combining rectangular and triangular fins has been employed to numerically simulate the melting process in the heat storage tank,and the fin geometry parameter effects on heat storage performance have been studied.The results indicate that compared with the bare tube and the rectangular finned tank,the melting time of the phase change material in the pointer-shaped finned tank is reduced by 64.2%and 15.1%,respectively.The closer the tip of the triangular fin is to the hot wall,the better the heat transfer efficiency.The optimal height of the triangular fin is about 8 mm.Increasing the number of fins from 4 to 6 and from 6 to 8 reduces the melting time by 16.0%and 16.7%respectively.However,increasing the number of fins from 8 to 10 only reduces the melting time by 8.4%.When the fin dimensionless length is increased from 0.3 to 0.5 and from 0.5 to 0.7,the melting time is shortened by 17.5%and 13.0%.But the melting time is only reduced by 2.9%when the dimensionless fin length is increased from 0.7 to 0.9.For optimising the design of the thermal storage system,the results can provide a reference value.

Natural Convection Melting in a Rectangular Heat Storage Tank of Carbon Nanotube Dispersed Latent Heat Storage Material

A dispersion system fluid can convect even if the dispersoid is a solid phase.Therefore,heat exchange performance can be improved while maintaining fluidity using a material with high thermal conductivity as the dispersoid.This study presents the melting performance evaluation results of a latent heat storage material with a carbon nanotube(CNT)dispersion system with high thermal conductivity,which enhances the thermal conductivity of the latent heat storage material and does not limit free convection.Increasing the thermal conductivity and enhancing the melting convection of the heat storage material result in increased latent heat storage speed.In this study,the thermal conductivity of the latent heat storage material was successfully increased by dispersing CNTs in the material.When 0.1%(in mass)of multi-wall CNT(MWCNT)was dispersed in a paraffin-based latent heat storage material,the shear stress increased by 1.5 times at a shear rate of 500 s^(-1),while taking into account the potential effects of convective inhibition.Therefore,a latent heat storage experiment was conducted in a rectangular heat storage tank using the CNT dispersion composition ratio as a parameter.A rectangular vessel with a heated vertical surface was used for the latent heat storage experiment.The melting speed was determined by comparing the amount of latent heat stored in a CNT-dispersed latent heat storage material and a single-phase latent heat storage material sample.The experimental results show that the time required for the latent heat storage material to completely melt in the heat storage tank was the shortest for the single-phase latent heat storage material sample.However,the fastest melting progress was observed for the sample with 0.02%(in mass)MWCNT content in the melting rate range of up to approximately 40%in the tank.The results indicate that this phenomenon is caused by the difference in the melting rates in the upper part of the tank.The generated data are useful for determining the shape and heat transfer surface arrangement of the latent heat storage tank.

Comparison of Thermal Performance between Annular Fins and Longitudinal Fins in Latent Heat Storage Unit

As a simple and effective method of heat transfer enhancement,fins are widely used in latent heat storage systems.However,the choice of annular fins and longitudinal fins has always been controversial.In this paper,the melting process of phase change material(PCM)in annular fins and longitudinal fins latent heat storage units with the same volume is numerically simulated.To ensure the same thermal penetration,three-dimensional spaces occupied with fins are specially controlled to be the same.Combined with finned structures,the effects of natural convection(NC),placement mode and heat transfer fluid(HTF)inlet direction on the melting process are studied.The results show that the melting time in annular finned structure is always 10%less than that in longitudinal finned structure,which demonstrates the superior of the annular fins in the latent heat storage unit.The melting time is the shortest in vertical unit with annular fins and HTF inlet at the bottom.Additionally,the correlation formulas of the liquid fraction are proposed in the vertical unit with HTF inlet at the bottom.

Thermal performance and evaluation of a novel stratified and mixed flexible transformation solar heat storage unit

It is necessary to satisfy the flexible requirements of solar heat storage systems to provide efficient heating and constant-temperature domestic hot water at different periods.A novel heat storage tank with both stratified and mixing functions is proposed,which can realize the integration of stable stratification and rapid mixing modes.In this research,a three-dimensional heat transfer model of the heat storage tank with stratified and mixed dual modes was established,and a thermal performance test system for the tank was built in the State Key Laboratory of Green Building in Western China.Moreover,a new evaluation index representing the mixing speed is proposed.The stratification effect and mixing characteristics of the tank were studied under different comprehensive conditions.The results show that the exergy efficiency of the tank with a stratified pipe can be increased by 10%–15%compared to that of a conventional tank.Additionally,the recommended optimal flow rate range for well-stratified tanks is 4–6 L/min.The mixing nozzle of the tank reduces the mixing reaction coefficient by 0.27 and significantly reduces the mixing time.This study provides critical guidance to meet the flexible thermal needs of users and implement high-performance applications using the stratified and mixing modes of heat storage tanks.

Enhanced Phase Change Heat Storage of Layered Backfill Body under Different Boundary Conditions

In view of the high temperature problem faced by mining activities,the coordinated mining of ore deposit and geothermal energy is a solution in line with the concept of green mining.The layered backfill body with finned double-pipe heat exchanger continuously exchanges heat with the surrounding thermal environment,which plays an effective role in gathering geothermal energy.In this paper,the heat storage process of each layered backfill body under different boundary conditions is simulated by Fluent.The results show the heat storage characteristic of layered backfill body can be significantly improved by adding fins to the double-pipe heat exchanger.On the whole,the heat storage effect of bottom layer backfill body(BLBB)is the best.The total heat storage capacity of top layer backfill body(TLBB),middle layer backfill body(MLBB)and BLBB with the finned double-pipe heat exchanger is 666.3 kJ,662.2 kJ,1003.0 kJ;1639.0 kJ,1760.8 kJ,1911.2 kJ and 1731.1 kJ,1953.3 kJ,1962.8 kJ respectively at 1 h,8 h and 24 h.This study explores the law of heat storage of layered backfill body under different boundary conditions and also expands the idea for layered backfill body to efficiently accumulate geothermal energy.

Heat Storage/Heat Release of Phase-Change Filling Body with Casing Heat Exchanger for Extracting Geothermal Energy

Arranging heat exchanger in filling body to extract geothermal energy is an effective way to alleviate the problems of high ground pressure and high ground temperature in deep resource exploitation.Filling body with casing heat exchanger was acted as research object,encapsulating phase change materials(PCMs)in annular space.During heat storage and heat release process,the effects of different PCMs on temperature distribution,phase-change process and heat transfer performance were studied.The result indicates:During heat storage process,the temperature increases rapidly and the melting process is accelerated for the position closer surrounding rock.CaCl_(2)·6H_(2)O/EG can make filling body complete heat storage process in the shortest time because of its good thermal diffusivity.The heat storage capacity of PCMs backfill is significantly higher than that of ordinary backfill;it increases by 36.6%-67.3%at heat storage of 10 h.During heat release process,the closer to the heat exchange tube,the greater the temperature drop in filling body.The maximum value of heat release rate and heat release capacity is in CaCl_(2)·6H_(2)O/EG backfill,it can release 116.4%more heat than RT35backfill after heat release of 12 h,the maximum value of effectiveness and its heat transfer rate also is in CaCl_(2)·6H_(2)O/EG backfill.This paper provides the basic data for the selection of PCMs in phase-change thermal storage filling body.

Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.