Performance of underground heat storage system in a double-film-covered greenhouse

An underground heat storage system in a double-film-covered greenhouse and an adjacent greenhouse without the heat storage system were designed on the basis of plant physiology to reduce the energy consumption in greenhouses. The results indicated that the floor temperature was respectively 5.2℃, 4.6℃ and 2.0 ℃ higher than that of the soil in the adjacent reference greenhouse after heat storage in a clear, cloudy and overcast sky in winter. Results showed that the temperature and humidity were feasible for plant growth in the heat saving greenhouse.

The Effect of Water Flow Velocity on Heat Collection Performance of Active Heat Storage and Release System for Solar Greenhouses

In order to explore the influence of water velocity on the heat collection performance of the active heat storage and release system for solar greenhouses,six different flow rates were selected for treatment in this experiment.The comprehensive heat transfer coefficient of the active heat storage and release system at the heat collection stage was calculated by measuring the indoor solar radiation intensity,indoor air temperature and measured water tank temperature.The prediction model of water temperature in the heat collection stage was established,and the initial value of water temperature and the comprehensive heat transfer coefficient were input through MATLAB software.The simulated value of water temperature was compared with the measured value and the results showed that the best heat transfer effect could be achieved when the water flow speed was 1.0 m3h-1.The average relative error between the simulated water tank temperature and the measured value is 2.70-6.91%.The results indicate that the model is established correctly,and the variation trend of water temperature can be predicted according to the model in the heat collection stage.

Optimal Scheduling Method of Cogeneration System with Heat Storage Device Based on Memetic Algorithm

Electric-heat coupling characteristics of a cogeneration system and the operating mode of fixing electricity with heat are the main reasons for wind abandonment during the heating season in the Three North area.To improve the wind-power absorption capacity and operating economy of the system,the structure of the system is improved by adding a heat storage device and an electric boiler.First,aiming at the minimum operating cost of the system,the optimal scheduling model of the cogeneration system,including a heat storage device and electric boiler,is constructed.Second,according to the characteristics of the problem,a cultural gene algorithm program is compiled to simulate the calculation example.Finally,through the system improvement,the comparison between the conditions before and after and the simulation solutions of similar algorithms prove the effectiveness of the proposed scheme.The simulation results show that adding the heat storage device and electric boiler to the scheduling optimization process not only improves the wind power consumption capacity of the cogeneration system but also reduces the operating cost of the system by significantly reducing the coal consumption of the unit and improving the economy of the system operation.The cultural gene algorithm framework has both the global evolution process of the population and the local search for the characteristics of the problem,which has a better optimization effect on the solution.

Numerical study of solar absorption heat storage system applied to Bucharest city

Buildings represent a large part in terms of fossil energy consumption,which depends on the great need for heating.Even if the solar absorption heat storage system is possible,the performance of this system is affected by the cycle limits and the climatic conditions.The goal of the present study is to control the thermal performance of the system cycle according to the imposed climatic conditions of Bucharest city,Romania,and therefore a numerical model was developed for this purpose.The scheme and the thermodynamic cycle,the energy and mass balance equations,and the computational algorithm were presented.The results show that the cycle temperature increases at the end of desorption when the heating power supplied to the desorber is increased,which is also proportional to the drop in temperature at the beginning of the desorption.The temperature at the end of absorption and the mass flow rates of the solution have a significant effect on the thermal power released from the absorber and used to heat the building.For an average daily heat power of 1.35 kW/m^(2) and 10 hours per day of heating the building,the system with a solar collector area of 3 m^(2) has the capacity of heat supply for all the cold period.However,an economic strategy remains necessary.

Comparison and Performance Analysis of Heat Storage Equipment in Solar Heating System

Solar heating system is widely used recently. Heat storage equipment is the guarantee for steady performance of solar heating system. A design of latent heat storage exchanger with submerged coil was introduced with the structure, working principle, and the main advantages. This heat exchanger was integrated into solar heating system as the heat storage equipment. Advantage comparison of the designed heat exchanger in solar heating system with hot water tank was carried out. The analysis results show that the latent heat storage exchanger is superior to hot water tank obviously. The heat exchanger performance parameters and variations of these parameters are got： （1） with the increase of phase change material （PCM） volume ratio, heat storage equipment volume ratio decreases; （2） heat storage efficiency has the same varying tendency with outdoor and air temperature; while the bigger PCM volume ratio is, the weaker the effect of outdoor air temperature on heat storage efficiency is; （3） heat storage capacity and heat storage efficiency increase together; when PCM volume ratio is big, heat storage efficiency is high and the system can begin operating effcienfly and quickly; （4） with the increase of heat storage capacity, life cyde operation cost （LCOC） of system increases gradually in high speed; but with the increase of PCM volume ratio, the difference between the two systems LCOCs becomes smaller and smaller; （5） the reasonable range of PCM volume ratio is 0.5 - 0.7. Temperature characteristic analysis shows that, with the filled PCM, heat storage medium temperature presents several segments at different time, under conditions of different heat storage capacity and different PCM state.

Research on Operation Optimization of Heating System Based on Electric Storage Coupled Solar Energy and Air Source Heat Pump

For heating systems based on electricity storage coupled with solar energy and an air source heat pump(ECSA),choosing the appropriate combination of heat sources according to local conditions is the key to improving economic efficiency.In this paper,four cities in three climatic regions in China were selected,namely Nanjing in the hot summer and cold winter region,Tianjin in the cold region,Shenyang and Harbin in the severe cold winter region.The levelized cost of heat(LCOH)was used as the economic evaluation index,and the energy consumption and emissions of different pollutants were analyzed.TRNSYS software was used to simulate and analyze the system performance.The Hooke-Jeeves optimization algorithm and GenOpt software were used to optimize the system parameters.The results showed that ECSA systemhad an excellent operation effect in cold region and hot summer and cold winter region.Compared with ECS system,the systemenergy consumption,and the emission of different pollutants of ECSA system can be reduced by a maximum of 1.37 times.In cold region,the initial investment in an air source heat pump is higher due to the lower ambient temperature,resulting in an increase in the LOCH value of ECSA system.After the LOCH value of ECSA system in each region was optimized,the heating cost of the system was reduced,but also resulted in an increase in energy consumption and the emission of different pollutant gases.

Simultaneous CO_(2) capture and thermochemical heat storage by modified carbide slag in coupled calcium looping and CaO/Ca(OH)2 cycles

The simultaneous CO_(2) capture and heat storage performances of the modified carbide slag with byproduct of biodiesel were investigated in the process coupled calcium looping and CaO/Ca(OH)2 thermochemical heat storage using air as the heat transfer fluid.The modified carbide slag with by-product of biodiesel exhibits superior CO_(2) capture and heat storage capacities in the coupled calcium looping and heat storage cycles.The hydration conversion and heat storage density of the modified carbide slag after 30 heat storage cycles are 0.65 mol·mol^(-1) and 1.14 GJ·t^(-1),respectively,which are 1.6 times as high as those of calcined carbide slag.The negative effect of CO_(2) in air as the heat storage fluid on the heat storage capacity of the modified carbide slag is overcome by introducing CO_(2) capture cycles.In addition,the CO_(2) capture reactivity of the modified carbide slag after the multiple calcium looping cycles is enhanced by the introduction of heat storage cycles.By introducing 10 heat storage cycles after the 10th and 15th CO_(2) capture cycles,the CO_(2) capture capacities of the modified carbide slag are subsequently improved by 32%and 43%,respectively.The porous and loose structure of modified carbide slag reduces the diffusion resistances of CO_(2) and steam in the material in the coupled process.The formed CaCO_(3)in the modified carbide slag as a result of air as the heat transfer fluid in heat storage cycles decomposes to regenerate CaO in calcium looping cycles,which improves heat storage capacity.Therefore,the modified carbide slag with by-product of biodiesel seems promising in the coupled calcium looping and CaO/Ca(OH)_(2) heat storage cycles.

Interannual variability of mixed layer depth and heat storage of upper layer in the tropical Pacific Ocean

By using the upper layer data(downloaded from the web of the Scripps Institution of Oceanography),the interannual variability of the heat storage of upper layer(from surface to 400 m depth) and the mixed layer depth in the tropical Pacific Ocean are investigated. The abnormal signal of the warm event comes from the central and west Pacific Ocean, whereas it is regarded that the abnormal signal of the warm event comes from the east Pacific Ocean in the popular viewpoint. From the viewpoint on the evolution of the interannual variability of the mixed layer depth and the heat storage of the whole upper layer, the difference between the two types of El Nino is so small that it can be neglected. During these two El Nino/La Nina events(1972/1973 and 1997/1998), other than the case of the heat storage or for the mixed layer depth, the abnormal signal propagates from the central and west Pacific Ocean to the east usually by the path along the equator whereas the abnormal signal propagates from the east to the west by the path northern to the equator. For the interannual variability, the evolution of the mixed layer depth corresponds to that of the heat storage in the upper layer very well. This is quite different from the evolution of seasonality.

Effect of Radial Porosity Oscillation on the Thermal Performance of Packed Bed Latent Heat Storage

Owing to its high heat storage capacity and fast heat transfer rate,packed bed latent heat storage(LHS)is considered as a promising method to store thermal energy.In a packed bed,the wall effect can impact the packing arrangement of phase change material(PCM)capsules,inducing radial porosity oscillation.In this study,an actual-arrangement-based three-dimensional packed bed LHS model was built to consider the radial porosity oscillation.Its fluid flow and heat transfer were analyzed.With different cylindrical sub-surfaces intercepted along the radial direction in the packed bed,the corresponding relationships between the arrangement of capsules and porosity oscillation were identified.The oscillating distribution of radial porosity led to a non-uniform distribution of heat transfer fluid(HTF)velocity.As a result,radial temperature distributions and liquid fraction distributions of PCMs were further affected.The effects of different dimensionless parameters(e.g.,tube-to-capsule diameter ratio,Reynolds number,and Stefan number)on the radial characteristics of HTF and PCMs were discussed.The results showed that different diameter ratios correspond to different radial porosity distributions.Further,with an increase in diameter ratio,HTF velocity varies significantly in the near wall region while the non-uniformity of HTF velocity in the center region will decrease.The Reynolds and Stefan numbers slightly impact the relative velocity distribution of the HTF-while higher Reynolds numbers can lead to a proportional improvement of velocity,an increase in Stefan number can promote heat storage of the packed bed LHS system.

Synthesis and characterization of salt-impregnated anodic aluminum oxide composites for low-grade heat storage

Thermochemical heat storage(THS)systems have recently attracted a lot of attention in research and development.In this study,an anodic aluminum oxide(AAO)template,fabricated by a two-step anodization method,was used for the first time as the matrix material for a THS system.Different salts were studied as thermochemical materials for their suitability in low-grade heat storage application driven by solar energy for an open system.Compositions were prepared by absorbing CaCl2,MgCl2,LiCl,LiNO3 and mixtures of these salts under a vacuum in an AAO matrix.Field Emission Scanning Electron Microscopy was used to examine the morphology of the produced AAO composites.Thermal energy storage capacities of the composites were characterized using a differential scanning calorimeter.Characterization analysis showed that anodized Al plates were suitable matrix materials for THS systems,and composite sorbent prepared with a 1:1 ratio LiCl/LiNO3 salt mixture had the highest energy value among all composites,with an energy density of 468.1 k J·kg-1.

Melting heat transfer enhancement of a horizontal latent heat storage unit by fern-fractal fins

The latent heat storage(LHS)technique is of crucial importance in chemical energy engineering.Inspired by multi-bifurcated fern leaves,a mimic fern-fractal fin is designed to improve the thermal energy charging efficiency.This paper develops a transient melting model of a rectangular LHS unit using fern-fractal fins,and their melting behaviors are compared with the conventional fins.Besides,a parametric optimization of fernfractal fins is conducted for maximizing the thermal efficiency based on the response surface method(RSM).The results indicate that the temperature uniformity is more superior and the melting duration is shorter for the fern-fractal LHS unit when compared with the conventional one.Interestingly,the fern-fractal LHS device presents a slower heat storage rate during the initial conduction-dominated and early convection-dominated melting stages,while a prominent melting enhancement is achieved during the later melting stage.The shortest melting time is obtained based on the RSM technique when a fern-fractal fin with length ratio α=0.94 and branch angle θ=54.7°is utilized.Compared with a conventional fin,the averaged heat storage rate increases by 88.3%,and the total melting time is declined by 40.3%for an optimized fern-fractal fin.

Seasonal Behavior of Pavement in Geothermal Snow-Melting System with Solar Energy Storage

A two-dimensional unsteady heat transfer model of pavement of geothermal road snow-melting system (GRSS) with solar energy storage is established and numerical simulation is carried out based on annual hourly meteorological data and boundary conditions. Simulated results show that ground surface temperature and heating flux decrease with the increase of buried depth, but increase with the increase of fluid temperature in winter. Heat-extracted amount and efficiency drop with the increase of fluid temperature in summer.Compared with ambient temperature, solar radiation has more direct influence on the heat-extracted flux of pipe walls of GRSS in summer. The relationships among maximum and idling snow-melting load, the rate of snowfall, ambient temperature and wind speed are made clear, which provides necessary references for the design and optimization of a practical road snow-melting system.

Fabrication of Al_2O_3-NaCl Composite Heat Storage Materials by One-step Synthesis Method

Thermal energy storage is an attractive option for effectiveness since it gives flexibility and reduces energy consumption and costs. New composite materials for storage and transformation of heat of NaCl-Al2O3composite materials were synthesized by one-step synthesis method. The chemical composition, morphology, structure, and thermal properties were investigated by XRD, EDS, SEM, and DSC. The results show that NaCl can be absorbed by Al2O3particle from 800 to 900 ℃ for Al2O3particle surface is rich active structure. The results also indicate that the leakage of NaCl when the phase change can be prevented by Al2O3particles and the enthalpy of phase change of NaCl-Al2O3material is 362 J/g. The composites have an excellent heat storage capacity. Therefore, this study contributes to one new thought and method to prepare high temperature heat storage material and this material can be applied in future thermal engineering.

Solar Desalination with Latent Heat Storage Materials and Solar Collector

Availability of clean water is going to become one of biggest demands of the country. Even though there arc various technologies available for purification of water harnessing solar energy fits the purpose for future problems. Distillation is one of many processes available for water purification, and solar energy is one of several forms of heat energy that can be used to energize this process. In this review a study is made to enhance the productivity of the solar stills by connecting solar still with latent heat storage and solar air heater in series and other factors like improving evaporation rate by maintaining Low depth, more exposure area, heat addition by solar collector and presence of latent heat storage material, which is a paraffin wax as a integral part of still. Latent heat storage is one of the most efficient ways of storing thermal energy. Unlike the sensible heat storage method, the latent heat storage method provides much higher storage density, with a smaller temperature difference between storing and releasing heat. Further augmentation of the yield by scraps, pebble, and sand are added.

Calcium looping heat storage performance and mechanical property of CaO-based pellets under fluidization

The CaO-based pellets were fabricated using extrusion-spheronization method for calcium looping thermochemical heat storage under the fluidization.The effects of adhesive,biomass-based pore-forming agent,binder and particle size on the heat storage performance and mechanical property of the CaObased pellets were investigated in a bubbling fluidized bed reactor.The addition of 2%(mass)polyvinylpyrrolidone as an adhesive not only helps granulate,but also improves the heat storage capacity of the pellets.All biomass-templated CaO-based pellets display higher heat storage capacity than biomass-free pellets,indicating that the biomass-based pore-forming agent is beneficial for heat storage under the fluidization.Especially,bagasse-templated pellets show the highest heat storage conversion of 0.61 after 10 cycles.Moreover,Al_(2)O_(3)as a binder for the pellets helps obtain high mechanical strength.The CaO-based pellets doped with 10%(mass)bagasse and 5%(mass)Al_(2)O_(3)reach the highest heat storage density of 1621 kJ·kg^(-1) after 30 cycles and the highest crushing strength of 4.98 N.The microstructure of the bagasse-templated pellets appears more porous than that of biomass-free pellets.The bagassetemplated CaO-based pellets doped with Al_(2)O_(3)seem promising for thermochemical heat storage under the fluidization,owing to the enhanced heat storage capacity,excellent mechanical strength,and simplicity of the synthesis procedure.

Effects of Porous Graphene on LiOH Based Composite Materials for Low Temperature Thermochemical Heat Storage

Thermochemical heat storage material inorganic hydrate LiOH is selected as a promising candidate material for storing low-temperature heat energy because of its high energy density(1440 kJ/kg)and mild reaction process.However,the low hydration rate of LiOH limits the performance of low temperature thermochemical heat storage system as well as the thermal conductivity.In this study,porous-graphene/LiOH composite thermochemical heat storage materials with strong water sorption property and higher thermal conductivity were synthesized by hydrothermal process.The experimental results show that the hydration rate of the composites was greatly improved.The heat storage density of the composite materials was increased by 47%(from 661 kJ/kg to 974 kJ/kg).By combing the porous graphene,the thermal conductivity of composites with different contents were highly increased by 21.1%to 78.7%,but the increase of heat storage density is opposite to that of thermal conductivity.The development of high-performance materials for thermochemical heat storage should consider the relationship between the heat storage density and thermal conductivity of the material,and the thermal conductivity of the supporter needs to be further improved.

Coordinated control strategy for wind power accommodation based on electric heat storage and pumped storage

To solve the severe problem of wind power curtailment in the winter heating period caused by ＂power determined by heat＂ operation constraint of cogeneration units, this paper analyzes thermoelectric load, wind power output distribution and fluctuation characteristics at different time scales, and finally proposes a two level coordinated control strategy based on electric heat storage and pumped storage. The optimization target of the first level coordinated control is the lowest operation cost and the largest wind power utilization rate. Based on prediction of thermoelectric load and wind power, the operation economy of the system and wind power accommodation level are improved with the cooperation of electric heat storage and pumped storage in regulation capacity. The second level coordinated control stabilizes wind power real time fluctuations by cooperating electric heat storage and pumped storage in control speed. The example results of actual wind farms in Jiuquan, Gansu verifies the feasibility and effectiveness of the proposed coordinated control strategy.

Performance Assessment of a Box Type Solar Cooker Using Jatropha Oil as a Heat Storage Material

Solar cookers are a good option in developing countries with high solar potential for environmentally friendly cooking and reduced pressure on forests. However, they are still affected by the intermittency of the sun. In order to overcome this problem, in this work, a box type solar cooker integrated Jatropha oil as a heat storage material is fabricated and experimented with. The design was examined with a maximum stagnation temperature of 157.7°C. The recorded cooking power vanished between 78.4 and 103.6 W, while thermal efficiency varied from 41.26% to 58.78%. The energy transfer cycle test, including charge and discharge revealed that 91.18% of the heat lost through the cooker could be recovered by the heat storage unit and a large amount is restored to the system during cloudiness or a temperature perturbation.

Chemical Heat Storage Using an SiC Honeycomb Packed with CaCl₂Powder

Chemical heat storage is a promising technology for improving thermal energy efficiency. In this study, CaCl2 and H2O were selected as a reaction system for utilization of low-grade exhaust heat that is cooler than 200°C. Heat discharging and charging were conducted through the CaCl2 hydration reaction. A silicon carbide honeycomb was adopted to improve heat transfer in the CaCl2 packed bed. The heat storage, condenser, and evaporator temperature were set at 150°C, 30°C and 90°C respectively. Repeated trials and experiments are time consuming for optimizing design of the equipment. Therefore, in this research, we constructed a simulation that can predict the performance of the device. A numerical simulation model was utilized in preparation for the design of the heat storage module. The consistency of both the simulation and the experimental results was confirmed by comparing them.

Thermochemical Heat Storage Performance in the Gas/Liquid-Solid Reactions of SrCl2 with NH3

Thermochemical heat storage is a promising technology for improving energy efficiency through the utilization of low-grade waste heat. The formation of a SrCl2 ammine complex was selected as the reaction system for the purpose of this study. Discharge characteristics were evaluated in a packed bed reactor for both the gas-solid reaction and the liquid-solid reaction. The average power of the gas-solid reaction was influenced by the pressure of the supplied ammonia gas, with greater powers being recorded at higher ammonia pressure. For the liquid-solid reaction, the obtained average power was comparable to that obtained for the gas-solid reaction at 0.2 MPa. Moreover, the lower heat transfer resistance in the reactor was observed, which was likely caused by the presence of liquid ammonia in the system. Finally, the short-term durability of the liquid-solid reaction system was demonstrated over 10 stable charge/discharge cycles.