Improving Heat Transfer in Parabolic Trough Solar Collectors by Magnetic Nanofluids

A parabolic trough solar collector(PTSC)converts solar radiation into thermal energy.However,low thermal efficiency of PTSC poses a hindrance to the deployment of solar thermal power plants.Thermal performance of PTSC is enhanced in this study by incorporating magnetic nanoparticles into the working fluid.The circular receiver pipe,with dimensions of 66 mm diameter,2 mm thickness,and 24 m length,is exposed to uniform temperature and velocity conditions.The working fluid,Therminol-66,is supplemented with Fe3O4 magnetic nanoparticles at concentrations ranging from 1%to 4%.The findings demonstrate that the inclusion of nanoparticles increases the convective heat transfer coefficient(HTC)of the PTSC,with higher nanoparticle volume fractions leading to greater heat transfer but increased pressure drop.The thermal enhancement factor(TEF)of the PTSC is positively affected by the volume fraction of nanoparticles,both with and without a magnetic field.Notably,the scenario with a 4%nanoparticle volume fraction and a magnetic field strength of 250 G exhibits the highest TEF,indicating superior thermal performance.These findings offer potential avenues for improving the efficiency of PTSCs in solar thermal plants by introducing magnetic nanoparticles into the working fluid.

Regularization Method to the Parameter Identification of Interfacial Heat Transfer Coefficient and Properties during Casting Solidification

The accurate material physical properties, initial and boundary conditions are indispensable to the numerical simulation in the casting process, and they are related to the simulation accuracy directly. The inverse heat conduction method can be used to identify the mentioned above parameters based on the temperature measurement data. This paper presented a new inverse method according to Tikhonov regularization theory. A regularization functional was established and the regularization parameter was deduced, the Newton-Raphson iteration method was used to solve the equations. One detailed case was solved to identify the thermal conductivity and specific heat of sand mold and interfacial heat transfer coefficient (IHTC) at the meantime. This indicates that the regularization method is very efficient in decreasing the sensitivity to the temperature measurement data, overcoming the ill-posedness of the inverse heat conduction problem (IHCP) and improving the stability and accuracy of the results. As a general inverse method, it can be used to identify not only the material physical properties but also the initial and boundary conditions' parameters.

Thermal Conductivity and Heat Transfer Coefficient of Concrete

A very simple model for predicting thermal conductivity based on its definiensis was presented. The thermal conductivity obtained using the model provided a good coincidence to the investigations performed by other authors. The heat transfer coefficient was determined by inverse analysis using the temperature measurements. From experimental results, it is noted that heat transfer coefficient increases with the increase of wind velocity and relative humidity, a prediction equation on heat transfer coefficient about wind velocity and relative humidity is given.

Determination of interfacial heat transfer coefficient and its application in high pressure die casting process

In this paper,the research progress of the interfacial heat transfer in high pressure die casting(HPDC)is reviewed.Results including determination of the interfacial heat transfer coefficient(IHTC),influence of casting thickness,process parameters and casting alloys on the IHTC are summarized and discussed.A thermal boundary condition model was developed based on the two correlations:(a)IHTC and casting solid fraction and(b)IHTC peak value and initial die surface temperature.The boundary model was then applied during the determination of the temperature field in HPDC and excellent agreement was found.

A Numerical Method on Inverse Determination of Heat Transfer Coefficient Based on Thermographic Temperature Measurement

The heat transfer coefficient in a multidimensional heat conduction problem is obtained from the solution of the inverse heat conduction problem based on the thermographic temperature measurement. The modified one-dimensional correction method （MODCM）, along with the finite volume method, is employed for both two- and three-dimensional inverse problems. A series of numerical experiments are conducted in order to verify the effectiveness of the method. In addition, the effect of the temperature measurement error, the ending criterion of the iteration, etc. on the result of the inverse problem is investigated. It is proved that the method is a simple, stable and accurate one that can solve successfully the inverse heat conduction problem.

Computation of synthetic surface heat transfer coefficient of 7B50 ultra-high-strength aluminum alloy during spray quenching

According to inverse heat transfer theory, the evolutions of synthetic surface heat transfer coefficient（SSHTC） of the quenching surface of 7B50 alloy during water-spray quenching were simulated by the Pro CAST software based on accurate cooling curves measured by the modified Jominy specimen and temperature-dependent thermo-physical properties of 7 B50 alloy calculated using the JMat Pro software. Results show that the average cooling rate at 6 mm from the quenching surface and 420-230 ℃（quench sensitive temperature range） is 45.78℃/s. The peak-value of the SSHTC is 69 kW/（m^2·K） obtained at spray quenching for 0.4 s and the corresponding temperature of the quenching surface is 160 ℃. In the initial stage of spray quenching, the phenomenon called ＂temperature plateau＂ appears on the cooling curve of the quenching surface. The temperature range of this plateau is 160-170℃ with the duration about 3 s. During the temperature plateau, heat transfer mechanism of the quenching surface transforms from nucleate boiling regime to single-phase convective regime.

High-Resolution Heat Transfer Coefficients Measurement for Jet Impingement Using Thermochromic Liquid Crystals

A high-resolution testing technique named liquid crystal thermography is used for the experimental study on jet array impingement to map out the distribution of heat transfer coefficients on the cooling surface. Effects of the impingement distance, the impinging hole arrangement and the initial crossflow on heat transfer characteristics are investigated. The thermal images show truly the features of local heat transfer for each jet impingement cooling. The applications of thermochromic liquid crystal are successful in the qualitative and quantitative measurement for heat transfer coefficients distribution.

Establishment and Application of UFC-ACC Heat Transfer Coefficient Model

Based on medium plate runout table ultra-fast cooling( UFC)-accelerated cooling equipment( ACC) system,a heat transfer coefficient model was constructed. Firstly,according to the measured data,heat transfer coefficients under different roll speed and water volume were calculated by using an inverse heat conduction method. Secondly,a monofactorial heat transfer coefficient calculation formula was obtained. Finally,the heat transfer coefficient model based on medium plate runout table UFC-ACC system was constructed by intercept function,slope function,interaction influence function and linear or nonlinear influencing factors. The precision of these models was validated by comparing model prediction value with measured data,and the results were in good agreement with practical needs,and the average deviation was less than 5%.

Measurement of temperature inside die and estimation of interfacial heat transfer coefficient in squeeze casting

As an advanced near-net shape technology, squeeze casting is an excellent method for producing high integrity castings. Numerical simulation is a very effective method to optimize squeeze casting process, and the interfacial heat transfer coefficient(IHTC) is an important boundary condition in numerical simulation. Therefore, the study of the IHTC is of great significance. In the present study, experiments were conducted and a "plate shape" aluminum alloy casting was cast in H13 steel die. In order to obtain accurate temperature readings inside the die, a special temperature sensor units(TSU) was designed. Six 1 mm wide and 1 mm deep grooves were machined in the sensor unit for the placement of the thermocouples whose tips were welded to the end wall. Each groove was machined to terminate at a particular distance(1, 3, and 6 mm) from the front end of the sensor unit. Based on the temperature measurements inside the die, the interfacial heat transfer coefficient(IHTC) at the metal-die interface was determined by applying an inverse approach. The acquired data were processed by a low pass filtering method based on Fast Fourier Transform(FFT). The feature of the IHTC at the metal-die interface was discussed.

Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

The high pressure die casting (HPDC) process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today's manufacturing industry. In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC) was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger, and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified, when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

Influence of nanoparticle concentrations on flow boiling heat transfer coefficients of Al_2O_3/R141b in micro heat exchanger by direct metal laser sintering

Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80 in micro heat exchanger by direct metal laser sintering. Experimental results show that nanoparticle concentrations have significantly impact on heat transfer coefficients by homogeneity test of variances according to mathematical statistics. The heat transfer performance of Al2O3/R141b ＋ Span-80 nanorefrigerant is enhanced after adding nanoparticles in the pure refrigerant R141b. The heat transfer coefficients of 0.05 wt.%, 0.1 wt.%, 0.2 wt.%, 0.3 wt.% and 0.4 wt.% Al2O3/R141 b ＋ Span-80 nanorefrigerant respectively increase by 55.0% 72.0%, 53.0% 42.3% and 39.9% compared with the pure refrigerant R141b. The particle fluxes from viscosity gradient, non-uniform shear rate and Brownian motion cause particles to migrate in fluid especially in the process of flow boiling. This migration motion enhances heat transfer between nanoparticles and fluid. Therefore, the heat transfer performance of nanofluid is enhanced. It is important to note that the heat transfer coefficients nonlinearly increase with nanoparticle concentrations increasing. The heat transfer coefficients reach its maximum value at the mass concentration of 0.1% and then it decreases slightly. There exists an optimal mass concentration corresponding to the best heat transfer enhancement. The reason for the above phenomenon is attributed to nanoparticles deposition on the minichannel wall by Scanning Electron Microscopy observation. The channel surface wettability increases during the flow boiling experiment in the mass concentration range from 0.2 wt.% to 0.4 wt.%. The channel surface with wettability increasing needs more energy to produce a bubble. Therefore, the heat transfer coefficients decrease with nanopartide concentrations in the range from 0.2 wt.% to 0.4 wt.%. In addition, a new correlation has been proposed by fitting the experimental data considering the influence of mass concentrations on the heat trans- fer performance. The new correlation can effectively predict the heat transfer coefficient.

Regularized determination of interfacial heat transfer coefficient during ZL102 solidification process

The interfacial heat transfer coefficient(IHTC)between the casting and the mould is essential to the numerical simulation as one of boundary conditions.A new inverse method was presented according to the Tikhonov regularization theory.A regularized functional was established and the regularization parameter was deduced.The functional was solved to determine the interfacial heat transfer coefficient by using the sensitivity coefficient and Newton-Raphson iteration method.The temperature measurement experiment was done to ZL102 sand mold casting,and the appropriate mathematical model of the IHTC was established.Moreover, the regularization method was used to determinate the IHTC.The results indicate that the regularization method is very efficient in overcoming the ill-posedness of the inverse heat conduction problem(IHCP),and ensuring the accuracy and stability of the solutions.

Equivalent heat transfer coefficient at casting/Cu mould interface and temperature field simulation

Using the inverse algorithm of heat transfer and the nonlinear estimation method, matching calculated values with measured ones, the interfacial heat transfer coefficient at casting/Cu mould interface was determined.The results show that the interfacial heat transfer coefficient at Al/Cu interface changes in a range of 4.0×10 3 1.0×10 5 W·m -2 ·K -1 and its average value is in a range of 5.0×10 37.0×10 3 W·m -2 ·K -1 .

Heat Transfer Coefficient between Ice Cover and Water in the Bohai Sea

The calculative method of heat transfer coefficient between ice cover and water is analyzed considering the heat balance at ice cover bottom firstly. The heat transfer coefficient is calculated with the meteorological, oceanographic data and sea ice conditions measured on the JZ20-2 Oil/Gas Platform in the Bohai Sea during the winter of 1997/1998. From the results, it is shown that the heat transfer coefficient is smaller in the freezing and melting periods, which is about 0.16×10-3 and 0.04×10-3 respectively. In the middle of ice season, the heat transfer coefficient has a larger value, which is about 0.5×10-3. Lastly, the influences of ice thickness and ice type on the heat transfer coefficient are discussed. With the heat transfer coefficient determined above, the oceanic heat flux in the winter of 1997～1998 is calculated, and its trend in the winter is analyzed. This study can be referenced in the sea ice numerical simulation and prediction in the Bohai Sea.

Effect of Heat Transfer Coefficient on the Temperature Gradient for Hollow Fiber

The heat transfer coefficient h caused by blowing affects the heat transfer of fiber greatly. Especially,unsymmetrical blowing forms the unsymmetrical temperature gradient on the fiber cross.section. Based on the results of spinning simulation by computer, the changes of heat transfer coefficient on the cross-section along the spinning line and the effects on distributions of temperature gradients were discussedl It is showed that for the spinning simulation of hollow fiber under strong blowing condition, the heat transfer coetticient should bemodified as: h=0.437×10-4[ G/Vρ ( R2/ R2-n2 ) ] -o.333(V2+ 64( VYsin (θ))2)0.

Estimation of overall heat transfer coefficient of cooling system in RF capacitive hyperthermia

The study presented in this article involves the estimation of the overall heat transfer coefficient of cooling system in RF capacitive hyperthermia treatment using inverse problem based on the conjugate gradient method to provide improved distribution of temperature. The temperature data computed numerically from the direct problem using the finite difference time domain method are used to simulate the temperature measurements. The effects of the errors and sensor positions upon the precision of the estimated results are also considered. The results show that a reasonable estimation of the unknown can be obtained. Finally, measurements in a tissue-equivalent phantom are employed to appraise the reliability of the presented method. The comparison of computed data with measurements shows a good agreement between numerical and experimental results.

Optimal Experiment Design for the Identification of the Interfacial Heat Transfer Coefficient in Sand Casting

The interfacial heat transfer coefficient(IHTC)is one of the main input parameters required by casting simulation software.It plays an important role in the accurate modeling of the solidification process.However,its value is not easily identifiable by means of experimental methods requiring temperature measurements during the solidification process itself.For these reasons,an optimal experiment design was performed in this study to determine the optimal position for the temperature measurement and the optimal thickness of the rectangular cast iron part.This parameter was identified using an inverse technique.In particular,two different algorithms were used:Levenberg Marquard(LM)and Monte Carlo(MC).A numerical model of the solidification process was associated with the optimization algorithm.The temperature was measured at different positions from the mould/metal interface at d=0 mm(mould/metal interface),30 mm,60 mm and 90 mm.the thicknesses of the cast part were:L1=40 mm,60 mm and 80 mm.A comparative study on the IHTC identification was then carried out by varying the initial value of the IHTC between 500 Wm^(-2)K^(-1) and 1050 Wm^(-2)K^(-1).Results showed that the MC algorithm used for estimating the IHTC gives the best results,and the optimal position was at d=30 mm,the position closest to the mould/metal interface,for the lowest thickness L1=40 mm.

Laminar Heat Transfer Modeling and Investigation of Thermal Dispersion in a Flat Plate Heat Exchanger： Estimating Heat Transfer Coefficient, Heat Flux and Nusselt Number

PHEs （plate heat exchangers） are among the most common thermal equipments in diverse industries particularly in oil and gas companies. This wide usage is obviously due to significant benefits of these heat exchangers over other types. In this article, a behavioral analysis of heat transfer in fiat plates of these heat exchangers in laminar flow situation through CFD （computational fluid dynamics） simulation using FLUENT 6.3.26 software is done. The study reveals results graphically based on fluid＇s behavior in co-current and counter current flows and discusses thermal indexes consisting of heat transfer coefficient, Nusslet and total heat flux in both conditions. Eventually, a comparison via the graphical results is presented between the two types of flow directions.

Identification of Heat Transfer Coefficients by Use Conditions of Quenching Oil

Heat transfer coefficients of the quench medium are necessary for heat-treatment simulation. Cooling characteristics of quenching oil vary with kinds and usage greatly. Users are selecting oil solutions that come up to their desired hardness and quenching distortion requirements. In particular cooling performance rises by agitation and decompression. Therefore we identified a heat transfer coefficient by usage and kinds of quenching oil. Cooling characteristics are different greatly by a kind of quenching oil. A difference of a cooling characteristic by a kind of oil depends on a temperature range of a boiling stage and the maximum heat transfer coefficient mainly. On the other hand, in a convection stage, there are few changes in a boiling stage. Even if quenching oil temperature is changed, heat transfer coefficients do not change greatly. When quenching oil stirred, heat transfer coefficients of vapor blanket stage and a convection stage rise, but there are a few changes in a boiling stage. When quenching oil is decompressed a temperature range of a high heat transfer coefficient moves to the low temperature side. In addition, a heat transfer coefficient in a vapor blanket stage comes down. For precision improvement of heat-treatment simulation, it is important that the heat transfer coefficient is calculated in conformity to the on-site use reality.

Effect Analysis of Volume Fraction of Nanofluid Al2O3-Water on Natural Convection Heat Transfer Coefficient in Small Modular Reactor

Development and use of nuclear energy is currently growing very rapidly, in order to achieve increasingly advanced technology, both in terms of design, economic factors and safety factors. Thermal-hydraulics aspects of nuclear reactors should be done with calculation and near-perfect condition. Including today began development of a nuclear reactor with low power below 300 MW, or commonly called the Small Modular Reactor (SMR). One is CAREM-25 developed by Argentina with a power of 25 MW, where in CAREM already using natural circulation system and the use of nanofluid as coolant fluid. In this research, analytic modeling of thermal-hydraulics nuclear reactor SMR CAREM-25, when the nanofluid Al2O3-Water used as cooling fluid in the cooling system of a nuclear reactor. Further to this analytic modeling will be done on CFD. Analytic modeling with CFD to determine the flow phenomena and distribution as well as the effect of nano-particles of Al2O3-Water based on the volume fraction (1% and 3%) of the coefficient of heat transfer by natural convection.